Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RANGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

An Evaluation of UAS Pilot Workload and Acceptability Ratings with Four Simulated Radar Declaration Ranges

Currently, minimum operational performance standards (MOPS) are being developed for a broader range of unmanned aircraft system (UAS) platforms, including smaller UAS that will feature onboard sensors that are low in size, weight, and power, otherwise known as low SWaP. The low SWaP sensors used to detect non-cooperative traffic will have limited declaration ranges compared to those designed for medium-to-large UAS. A human-in-the-loop (HITL) study was conducted examining four possible radar declaration ranges (i.e., 1.5 NM, 2 NM, 2.5 NM, and 3 NM) for a potential low SWaP sensor with a detect and avoid (DAA) system encountering various non-cooperative encounters in Oakland Center airspace. Participants had lower workload, particularly workload associated with temporal demand and effort, in scenarios that featured larger declaration ranges. Furthermore, participants reported better ability to remain DAA well clear within the larger declaration range conditions, specifically with the 2.5 NM and 3 NM conditions.

UAS↗
NASA NTRS2020

An Evaluation of UAS Pilot Workload and Acceptability Ratings with Four Simulated Radar Declaration Ranges

Currently, minimum operational performance standards (MOPS) are being developed for a broader range of unmanned aircraft system (UAS) platforms, including smaller UAS that will feature onboard sensors that are low in size, weight, and power, otherwise known as low SWaP. The low SWaP sensors used to detect non-cooperative traffic will have limited declaration ranges compared to those designed for medium-to-large UAS. A human-in-the-loop (HITL) study was conducted examining four possible radar declaration ranges (i.e., 1.5 NM, 2 NM, 2.5 NM, and 3 NM) for a potential low SWaP sensor with a detect and avoid (DAA) system encountering various non-cooperative encounters in Oakland Center airspace. Participants had lower workload, particularly workload associated with temporal demand and effort, in scenarios that featured larger declaration ranges. Furthermore, participants reported better ability to remain DAA well clear within the larger declaration range conditions, specifically with the 2.5 NM and 3 NM conditions.

UAS↗
NASA NTRSDate not supplied

Recent Progress in the International Laser Ranging Service (ILRS)

The International Laser Ranging Service (ILRS) provides Satellite Laser Ranging (SLR) and Lunar Laser Ranging (LLR) observations and data products with a focus on Earth and Lunar science and engineering applications. The basic observables are the precise two-way time-of-flight of ultra-short laser pulses from ground stations to retroreflector arrays on satellites and the Moon and the one-way time-of-flight measurements to space-borne receivers (transponders). SLR is one of the four space geodetic techniques (along with VLBI, GNSS, and DORIS). The International Terrestrial Reference Frame (ITRF) development, maintained by IERS, is based on these geodetic observations. Fundamental data products include accurate satellite ephemerides, Earth orientation parameters, three dimensional coordinates and velocities of the ILRS tracking stations, time-varying geocenter coordinates, static and time-varying coefficients of the Earth’s gravity field, fundamental physical constants, lunar ephemerides and librations, and lunar orientation parameters. The ILRS continues to expand spatial and temporal coverage of SLR observations. New stations with new technologies are being deployed; existing stations are being upgraded. Some of these stations are multi-technique Core Sites. New satellites are expanding applications and strengthening the ILRS contribution to the reference frame. New analysis, modeling, and data processing techniques are improving data products. New campaigns are expanding our applications into relativity and the study of non-gravitational forces. New activities are underway on Lunar Laser Ranging, Time Transfer, and Space Debris Tracking, helping to expand laser ranging applications. This talk will give an update on the current ILRS activities and their impact on ILRS data products.

Report on the ILRS activities↗
DOE OSTI2021

Assembling a Cyber Range to Evaluate Artificial Intelligence / Machine Learning (AI/ML) Security Tools

In this case study, we will describe the design and assembly of a cyber security test range we have built at Oak Ridge National Laboratory in Oak Ridge, TN, USA. The range is designed to provide a flexible environment to evaluate cyber security tools—particularly those involving AI/ML—in a way that provides realistic environments and where we can control the experiments to determine the strengths and weaknesses of the tools. We have designed in the ability to repeat the evaluations, so additional tools can be evaluated and compared at a later time. The system is one that can be scaled up or down for experiment sizes. At the time of the conference we will have completed two full-scale, national, government challenges on this range. These challenges are evaluating the performance and operating costs for AI/ML-based cyber security tools for application into large, government-sized environments. These evaluations will be described, in order to provide motivation and context for various design decisions and adaptations we have made. The first challenge measured end-point security tools against 100K malware samples chosen across a range of types. The second is network detection of attempted penetration and exploitations with varying levels of covertness in a high-volume, business network. The scale of each of these challenges is requiring us to create automation systems to repeat the experiments identically for each tool. Preventing there being easy signs of malicious activity for the AI/ML tools to focus on has been a particularly interesting and challenging aspect of designing and executing these challenge events. After the events, the range continues to be used for other research such as adversarial machine learning where the repeatability, scale, and automation required for the national challenge events become essential elements for research.

Nichols, Jeff↗
DOE OSTI2017

Wide-range fission chambers signal simulator - 373

Fission chambers (FC) signal simulators are a useful means to test neutron flux instrumentation channels of the reactors control and protection systems (CPS). Well-known signal simulators do not provide a secondary equipment testing in all modes of measurement. A wide range simulator that simulates a full range of FC signal changes (pulse, fluctuation, current) was designed. The simulator takes into account the statistical nature of neutrons detection in the FC, including the shape of the pulse and the spectrum of the pulse amplitude distribution. The simulator uses the principle of mathematical simulation of the fission chambers signal with realtime calculations using the FPGA. The wide-range simulator reproduces a FC signal in the range of ten orders without switching ranges or playback modes while ensuring very good linearity. It allows to generate both static and dynamic test signals such as: stair-step, linearly and exponential varying signals, exponential varying signals with a linearly changing period or a signal change simulating the response of the nuclear reactor power to a given reactivity response. Continuity of reproduced signals and the ability to playback dynamic effects makes it possible the simulator using to check the algorithms of cross-linking of measuring paths, reactivity and period measuring tools and to monitor the operation of interlocking and alarm CPS functions. This article discusses the simulator's software and hardware, its features and specifications, user interface and example of the simulator using to check the neutron flux monitoring channels. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Investigation of Benchmark $k$ eff Sensitivity and Uncertainty for 239 Pu fission in Specific Energy Ranges

Nuclear data at intermediate energies (from 1 to 100s of keV) are evaluated based on scarce differential data and theory unable to capture physics’ expected structure. There is also a lack of integral data. This is a known deficiency and is challenging to address. Calculated effective multiplication factor, k eff , values for intermediate energy experiments are ~25× further from experiment than for fast energies and are often well outside the experimental uncertainties. The goal of the PARADIGM (PARallel Approach of Differential and InteGral Measurements) project is to significantly re duce the uncertainties of intermediate energy nuclear data for 239 Pu. To this end, PARADIGM simultaneously optimizes experiments at both the Los Alamos Neutron Science Center (LANSCE) and National Criticality Experiments Research Center (NCERC). The combined set of data will inform new intermediate-energy nuclear data. By execution of differential and integral experiments, establishment of new theory, and undertaking nuclear data evaluation in parallel, the timeline to deliver improved nuclear data to users will be reduced significantly that is to three years. For the PARADIGM project, it was decided to optimize an integral experiment for two neutron energy ranges, within the full intermediate energy range. The low energy range goes from 1 to 30 keV, while the higher energy range goes from 30 to 600 keV. This work focuses on nuclear data sensitivities and uncertainties for 239 Pu fission for existing experiments in the International Criticality Safety Benchmark Evaluation Project (ICSBEP). When designing new experiments, it is important to understand what benchmarks currently exist. For a more traditional experiment design (in which a specific application model(s) exists), comparisons would be made between the application model(s) and existing benchmarks. For PARADIGM, there is no specific application model, but instead the specific nuclear data reaction and energy ranges of interest can be explored for existing benchmarks.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2015

Enhanced tunable magnetoresistance properties over a wide temperature range in epitaxial (La{sub 0.7}Sr{sub 0.3}MnO{sub 3}){sub 1−x}:(CeO{sub 2}){sub x} nanocomposites

Vertically aligned nanocomposite (VAN) (La{sub 0.7}Sr{sub 0.3}MnO{sub 3}){sub 1−x}:(CeO{sub 2}){sub x} (LSMO:CeO{sub 2}) thin films have been grown on SrTiO{sub 3} (001) substrates by pulsed laser deposition. Tunable magnetoresistance properties as well as microstructures are demonstrated in these VAN films by modulating the film composition (x = 0, 0.3, 0.4, 0.45, 0.5, and 0.55). The sample of x = 0.3 shows a large low-field magnetoresistance (LFMR) in a high temperature range, i.e., over 10% at the range of 280 K to 320 K under 1 T and with a peak value of ∼13.5% at 310 K. In addition, a vast enhancement of LFMR in a low temperature range of 20–150 K with peak of ≈34.3% at 45 K for 1 T could be achieved with x = 0.5. The enhanced LFMR properties can be attributed to both the phase boundary induced spin fluctuation and the magnetic tunneling effect through vertical ferromagnetic/insulator/ferromagnetic structures. The observed enhanced LFMR performance, especially at high temperatures, as well as its simple growth method, offers a great potential for LSMO:CeO{sub 2}nanocomposites to be used in spintronic devices in a large temperature range.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

Acoustic time-of-flight for proton range verification in water

Purpose: Measurement of the arrival times of thermoacoustic waves induced by pulsed proton dose depositions (protoacoustics) may provide a proton range verification method. The goal of this study is to characterize the required dose and protoacoustic proton range (distance) verification accuracy in a homogeneous water medium at a hospital-based clinical cyclotron. Methods: Gaussian-like proton pulses with 17 μs widths and instantaneous currents of 480 nA (5.6 × 10{sup 7} protons/pulse, 3.4 cGy/pulse at the Bragg peak) were generated by modulating the cyclotron proton source with a function generator. After energy degradation, the 190 MeV proton pulses irradiated a water phantom, and the generated protoacoustic emissions were measured by a hydrophone. The detector position and proton pulse characteristics were varied. The experimental results were compared to simulations. Different arrival time metrics derived from acoustic waveforms were compared, and the accuracy of protoacoustic time-of-flight distance calculations was assessed. Results: A 27 mPa noise level was observed in the treatment room during irradiation. At 5 cm from the proton beam, an average maximum pressure of 5.2 mPa/1 × 10{sup 7} protons (6.1 mGy at the Bragg peak) was measured after irradiation with a proton pulse with 10%–90% rise time of 11 μs. Simulation and experiment arrival times agreed well, and the observed 2.4 μs delay between simulation and experiment is attributed to the difference between the hydrophone’s acoustic and geometric centers. Based on protoacoustic arrival times, the beam axis position was measured to within (x, y) = (−2.0, 0.5) ± 1 mm. After deconvolution of the exciting proton pulse, the protoacoustic compression peak provided the most consistent measure of the distance to the Bragg peak, with an error distribution with mean = − 4.5 mm and standard deviation = 2.0 mm. Conclusions: Based on water tank measurements at a clinical hospital-based cyclotron, protoacoustics is a potential method for measuring the beam’s position (x and y within 2.0 mm) and Bragg peak range (2.0 mm standard deviation), although range verification will require simulation or experimental calibration to remove systematic error. Based on extrapolation, a protoacoustic arrival time reproducibility of 1.5 μs (2.2 mm) is achievable with 2 Gy of total deposited dose. Of the compared methods, deconvolution of the excitation proton pulse is the best technique for extracting protoacoustic arrival times, particularly if there is variation in the proton pulse shape.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2018

Tonopah Test Range Air Monitoring: CY2017 Meteorological, Radiological, and Wind Transported Particulate Observations

In 1963, the U.S. Department of Energy (DOE) (formerly the Atomic Energy Commission [AEC]), implemented Operation Roller Coaster on the Tonopah Test Range (TTR) and an adjacent area of the Nevada Test and Training Range (NTTR) (formerly the Nellis Air Force Range). This operation resulted in radionuclide-contaminated soils at the Double Tracks site and Clean Slate I, II, and III sites. This report documents observations made during ongoing monitoring of radiological, meteorological, and dust conditions at stations installed adjacent to the Clean Slate sites and at the TTR Sandia National Laboratories (SNL) Range Operations Center (ROC). The primary objective of the monitoring effort is to support the DOE Environmental Management Nevada Program (EM NV) in the safe cleanup of the environmental legacy of nuclear device development and testing by determining if wind blowing across the Clean Slate sites is transporting particles of radionuclide-contaminated soil beyond the physical and administrative boundaries of the sites. The monitoring program underwent a significant change during 2017 with the decommissioning of one monitoring station and the establishment of three new stations. Station 400, located within TTR Area 3 and near the ROC, monitors conditions near the local workforce center and was in operation the full calendar year. Stations 401 and 403 are located on the northwest and southeast perimeter fence lines, respectively, of the Clean Slate III site. Station 401 operated throughout 2017, whereas Station 403 began operation at the end of April 2017. Stations 404 and 405 are along the northern and eastern boundary fence, respectively, at Clean Slate II and both began data collection at the end of April 2017. Also at the end of April, the Clean Slate I monitoring site, Station 402, was decommissioned. The stations are located to be generally downwind of the contaminated areas during either north-northwesterly or south-southeasterly winds, which are the predominant wind directions. The stations—which are similar in design to the Community Environmental Monitoring Program (CEMP) stations operating at locations surrounding the Nevada National Security Site and TTR—include meteorological instruments and continuous-flow, low-volume air samplers. Three pressurized ionization chambers for measuring gamma energy are in use at Stations 400, 401, and 403 (formerly at 402). Saltation sensors and saltation traps are deployed at the stations adjacent to the Clean Slate sites. Detailed meteorological data are recorded on data loggers, with periodic uploads via a satellite system to the Western Regional Climate Center (WRCC) at Desert Research Institute (DRI), to monitor instrument and site conditions. Air filter samples are collected every two weeks and the deposits in the saltation traps are collected when a sufficient sample mass for analysis has accumulated (generally a six- to eight-month interval). Dust transport by suspension and saltation is strongly dependent on wind speed. Concentrations of PM10 (particulate matter of aerodynamic diameter ≤10 micrometers [μm], a size fraction of small particles that are suspended in the air and can be easily inhaled) remain low until winds exceed approximately 32 km/hr (20 mph). Saltation particle counts also increase above the same general threshold wind speed. Wind speeds in excess of 32 km/hr (20 mph) occur less than three percent of the time. High winds are associated with two predominant directions: north-northwest and south. In 2017, the very highest winds were from the north, but all winds above 40 km/hr (25 mph) were approximately evenly split between south and northwest directions. The low-volume air samplers collect total suspended dust, and saltating particles are captured by the passive saltation traps, both for radiological analysis. Radionuclide monitoring at the ROC in TTR Area 3 (Station 400) found natural background levels of gross alpha and gross beta radiation. Similar background levels were found on filter samples analyzed using gamma and alpha spectroscopy. The gamma exposure rate data from pressurized ionization chambers (PIC) are comparable to those from the regional CEMP stations. Plutonium concentrations above background values were measured during 2017 from soil samples collected in passive saltation traps and on select air filters from the monitoring stations adjacent to the Clean Slate sites. The background for soils in the region is assumed to be 0.014 pCi/g plutonium-239+240 ( 239+240 Pu) as measured by Turner et al. (2003), whereas the background concentration of suspended 239+240Pu is assumed to be 9.5 x 10 -19 μCi/ml, which was determined by continuous air monitoring at the TTR airport in 1996 and 1997 (SNL, 1998). Background concentrations are exceeded by one to four orders of magnitude by the majority of samples from Clean Slate I, II, and III. The gross alpha and gross beta measurements of the air filters are also generally higher than those measured at the regional CEMP stations, although the gamma exposure rates determined by the PICs located at Clean Slate I and III are similar to CEMP measurements. The highest radionuclide concentrations of suspended dust are associated with individual filter samples from Clean Slate II Station 404 and Clean Slate III Station 401. Both of the stations are downwind of their respective sites during southerly winds, but they are also geographically closer to the highly contaminated detonation areas than the other monitoring stations. Considering all the analyzed samples, the 239+240Pu concentrations are generally higher for the Clean Slate II samples compared with those from Clean Slate III. The highest gross alpha and gross beta results are also observed for the Clean Slate II stations. The highest radionuclide concentrations are measured on the smaller (≤63 μm) saltation-sized particles and particulate matter collected downwind of each site. Nonetheless, traps oriented to collect dust moving toward the contamination areas also had plutonium concentrations significantly above background values, which is consistent with observations of low-level contamination dispersed beyond the fenced area. All the observed 239+240 Pu concentrations are below the risk-based action level (25 millirem per year, equivalent to a 239+240 Pu concentration of 4,120 pCi/g for an industrial worker scenario; U.S. DOE, 2014). The meteorological and particulate matter monitoring indicate that conditions for wind-borne contaminant movement exist at the Clean Slate sites, and that transport of radionuclide-contaminated soil by both suspension and saltation is occurring. The Corrective Action Unit (CAU) closure strategy uses a risk-based approach, whereby acceptable contaminant concentrations are determined as a function of anticipated human exposure. This strategy is consistent with the fence lines at the Clean Slate sites encircling areas of higher concentration and the observed presence of lower concentrations of contamination outside the fences.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2011

Active Laser Ranging Along with Lasercom: Field Emulation

In summary, this work has: (1) Demonstrated the real-time active laser ranging using a method applicable to interplanetary distances (2) Sub-millimeter ranging accuracy has been achieved with the systems built from off-the-shelf commercial components, demonstrating the robustness of the scheme (3) The experimental results indicate that active laser ranging can be implemented for interplanetary distances to meet the goal of 1mm ranging accuracy, including the effects of the Earth's atmosphere (4) Paves the way for advances in the study of fundamental physics and solar system dynamics.

laser ranging↗
DOE OSTI2021

A record high average ZT over a wide temperature range in a Single-layer Sb 2 Si 2 Te 6

Conversion of waste heat into usable energy requires development of thermoelectric materials with high efficiency in a wide temperature range. Here, using first principles theory and Boltzmann transport theory, we show that the thermoelectric performance of the p-type single-layer Sb 2 Si 2 Te 6 has a high figure of merit ZT of 2.62 at 900 K and a record high average ZT of ~1.93 (corresponding the conversion efficiency of ~23.2%) in the temperature range of 300-900 K. These values are significantly higher than the recently measured average ZT of ~0.57 in the temperature range of 310–823 K [Luo et al., Joule 4, 159–175 (2020)] in layered bulk Sb 2 Si 2 Te 6 . We attribute the large enhancement of ZT in the single layer material to the increase in the thermoelectric power factor resulting from the complex Fermi surface. Our work reveals the great potential of a single-layer Sb 2 Si 2 Te 6 for wide-temperature-range thermoelectric applications.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Impact of long-range electrostatic and dispersive interactions on theoretical predictions of adsorption and catalysis in zeolites

In this article, we review the importance of long-range zeolite framework interactions in theoretical predictions for a variety of zeolite-catalyzed processes, and we show why such interactions must be determined accurately in order to reproduce experimentally measured adsorption and activation energies. We begin with an overview of the different strategies that have been used to account for long-range coulombic and dispersive interactions of zeolite framework atoms with species adsorbed at an active site. These methods include full periodic-DFT calculations and multi-layer hybrid techniques. Electrostatic interactions are observed to have a more significant impact than dispersive interactions on the geometries of ion-pair transition states and adsorbed species. Stabilization of the TS relative to reactant complexes is also dictated by electrostatic interactions. Dispersion effects are found to significantly stabilize both transition and reactant states for adsorbed species, especially those which have dimensions that provide good fits within the zeolite pore or cavity. We also show that the relevance of particular active site configurations can be missed, if the effects of long-range interactions are neglected. As a case in point, we demonstrate that a site previously considered inactive for ethane dehydrogenation, [GaH 2 ] + may in fact be more active than previously thought, when the impact of long-range interactions on the predicted activation energy is taken into account. In conclusion, the use of hybrid quantum mechanics/molecular mechanics approaches on extended, finite zeolite clusters has emerged as an accurate, highly cost-effective, and versatile alternative towards overcoming some of the present-day limitations of periodic calculations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Effects of ambient temperature on electric vehicle range considering battery Performance, powertrain Efficiency, and HVAC load

Here, this study investigates the impact of ambient temperature on the range of electric vehicles (EVs) by analyzing its effects on usable battery energy (UBE), heating, ventilation, and air conditioning (HVAC) energy consumption, and powertrain energy losses. Chassis dynamometer tests within a thermal chamber were conducted under various temperature conditions to investigate these impacts. The results indicate that lower temperatures lead to a decrease in UBE for lithium-ion batteries in EVs. At −18 °C, the UBE exhibited reductions of 4---8 % compared to the UBE at 22 °C. Battery thermal management strategies significantly affected the UBE loss, with different strategies resulting in distinct UBE reductions. HVAC energy consumption, especially for interior heating, proved to be the most dominant variable affecting EV driving range. Larger discrepancies between the HVAC target temperature (22 °C) and the ambient temperature increased HVAC energy usage. The type of HVAC system also influenced energy consumption, where EVs equipped with heat pumps demonstrated lower energy consumption for heating compared to those relying solely on resistance heaters. Ambient temperature also influenced motor energy consumption due to increased frictions, powertrain losses and tire rolling resistance at lower temperatures; consequently, regenerative braking energy decreased in cold conditions. Combining these effects influenced the overall energy consumption and driving range of EVs. At −18 °C, the driving range saw a substantial decrease of up to 60 % compared to 22 °C, while a slight decrease was observed at 35 °C.

Ambient Temperature↗
DOE OSTI2023

A study of examiner accuracy in cartridge case comparisons. Part 2: Examiner use of the AFTE range of conclusions

Here, this report describes an analysis of how examiners used the Association of Firearm and Toolmark Examiners (AFTE) Range of Conclusions in a controlled study undertaken to estimate examiner error rates in comparing cartridge cases. Results of the error rate analysis are reported in [1]; this paper focuses on a broader analysis of how the entire collection of classification categories, especially those in the Inconclusive range, were used by the participating examiners. Volunteer active examiners with AFTE membership or working in laboratories that participate in Association of Crime Laboratory Directors (ASCLD) were provided with 15 sets of three known and one questioned cartridge cases fired from a collection of 25 new Ruger SR9 handguns. Remington 9-mm Luger (manufacturer designation L9MM3) ammunition was used and comparison sets were made up of cartridge cases fired within 100 cartridges of each other for each gun. Examiners were provided with a background survey, an answer sheet allowing for the AFTE Range of Conclusions, and return shipping materials. The participating examiners were provided with both same-source and different-source comparison sets allowing the study to assess both error rates. Responses were received from 218 participating examiners. The overall rate of false-negatives was estimated as 0.367 % from comparisons known to be from the same firearm but reported as eliminations. The overall rate of false-positives was estimated as 1.01 % from comparisons known to be from different firearms but reported as identifications. In the case of true different-source examinations, it is clear that the three Inconclusive categories and the Elimination category are not used consistently by all examiners. We identify five different apparent patterns of use of the AFTE Range of Conclusions scale, and discuss possible reasons for and implications of these differences.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2020

Exploiting ultra-large linear elasticity over a wide temperature range in nanocrystalline NiTi alloy

Many shape memory alloys can support large recoverable strains of a few percent by reversible stress-induced martensite transformation, yet they behave non-linear within a narrow operating temperature range. Developing the bulk metallic materials with ultra-large linear elasticity over a wide temperature range has proven to be difficult. In this work, a material design concept was proposed, that is true elastic deformation and reversible twinning-detwinning deformation run in parallel to overcome this challenge. By engineering the residual internal stress to realize the concurrency of true elastic deformation and twinning-detwinning deformation, a bulk nanocrystalline NiTi that possesses an ultra-large linear elastic strain up to 5.1 % and a high yield stress of 2.16 GPa over a wide temperature range of 270 °C was developed. This study offers a new avenue for developing the metallic materials with ultra-large linear elasticity over a wide temperature range of 270 °C (from 70 °C to -197 °C).

36 MATERIALS SCIENCE↗
DOE OSTI2012

Sensitivity of Battery Electric Vehicle Economics to Drive Patterns, Vehicle Range, and Charge Strategies

Battery electric vehicles (BEVs) offer the potential to reduce both oil imports and greenhouse gas emissions, but high upfront costs discourage many potential purchasers. Making an economic comparison with conventional alternatives is complicated in part by strong sensitivity to drive patterns, vehicle range, and charge strategies that affect vehicle utilization and battery wear. Identifying justifiable battery replacement schedules and sufficiently accounting for the limited range of a BEV add further complexity to the issue. The National Renewable Energy Laboratory developed the Battery Ownership Model to address these and related questions. The Battery Ownership Model is applied here to examine the sensitivity of BEV economics to drive patterns, vehicle range, and charge strategies when a high-fidelity battery degradation model, financially justified battery replacement schedules, and two different means of accounting for a BEV's unachievable vehicle miles traveled (VMT) are employed. We find that the value of unachievable VMT with a BEV has a strong impact on the cost-optimal range, charge strategy, and battery replacement schedule; that the overall cost competitiveness of a BEV is highly sensitive to vehicle-specific drive patterns; and that common cross-sectional drive patterns do not provide consistent representation of the relative cost of a BEV.

25 ENERGY STORAGE↗
DOE OSTI2019

Extending the dynamic range of electronics in a Time Projection Chamber

When Time Projection Chambers (TPCs) are used in low to intermediate heavy ion collisions, the mass and momentum range of the emitted particles cover a wide range in energy losses. Many TPC readout electronics currently only have a single gain output with a fixed dynamic range. In a recent set of experiments using the SAMURAI Pion-Reconstruction and Ion-Tracker (StrRIT) TPC, it was important to simultaneously measure relativistic pions and heavy ion tracks from the same collisions. As the ionization from a track's energy loss is collected and multiplied by the anode wires, a distribution of image charges is induced on the TPC read-out pads. If the avalanche on a wire is large enough, the charge collected by pads directly underneath will saturate the readout electronics; pads farther away in the distribution will not be saturated. Using these unsaturated pads and the known pad distribution function, we can estimate the charge on saturated pads, increasing the dynamic range by a factor of 5.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Long-Range Dipole–Dipole Interactions in a Plasmonic Lattice

Spontaneous emission of quantum emitters can be enhanced by increasing the local density of optical states, whereas engineering dipole-dipole interactions requires modifying the two-point spectral density function. Here, we experimentally demonstrate long-range dipole-dipole interactions (DDIs) mediated by surface lattice resonances in a plasmonic nanoparticle lattice. Using angle-resolved spectral measurements and fluorescence lifetime studies, we show that unique nanophotonic modes mediate long-range DDI between donor and acceptor molecules. We observe significant and persistent DDI strengths for a range of densities that map to similar to 800 nm mean nearest-neighbor separation distance between donor and acceptor dipoles, a factor of similar to 100 larger than free space. Here, our results pave the way to engineer and control long-range DDIs between an ensemble of emitters at room temperature.

77 NANOSCIENCE AND NANOTECHNOLOGY↗