Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Propulsion Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

A Virtual Laboratory for Aviation and Airspace Prognostics Research

Integration of Unmanned Aerial Vehicles (UAVs), autonomy, spacecraft, and other aviation technologies, in the airspace is becoming more and more complicated, and will continue to do so in the future. Inclusion of new technology and complexity into the airspace increases the importance and difficulty of safety assurance. Additionally, testing new technologies on complex aviation systems and systems of systems can be challenging, expensive, and at times unsafe when implementing real life scenarios. The application of prognostics to aviation and airspace management may produce new tools and insight into these problems. Prognostic methodology provides an estimate of the health and risks of a component, vehicle, or airspace and knowledge of how that will change over time. That measure is especially useful in safety determination, mission planning, and maintenance scheduling. In our research, we develop a live, distributed, hardware- in-the-loop Prognostics Virtual Laboratory testbed for aviation and airspace prognostics. The developed testbed will be used to validate prediction algorithms for the real-time safety monitoring of the National Airspace System (NAS) and the prediction of unsafe events. In our earlier work1 we discussed the initial Prognostics Virtual Laboratory testbed development work and related results for milestones 1 & 2. This paper describes the design, development, and testing of the integrated tested which are part of milestone 3, along with our next steps for validation of this work. Through a framework consisting of software/hardware modules and associated interface clients, the distributed testbed enables safe, accurate, and inexpensive experimentation and research into airspace and vehicle prognosis that would not have been possible otherwise. The testbed modules can be used cohesively to construct complex and relevant airspace scenarios for research. Four modules are key to this research: the virtual aircraft module which uses the X-Plane simulator and X-PlaneConnect toolbox, the live aircraft module which connects fielded aircraft using onboard cellular communications devices, the hardware in the loop (HITL) module which connects laboratory based bench-top hardware testbeds and the research module which contains diagnostics and prognostics tools for analysis of live air traffic situations and vehicle health conditions. The testbed also features other modules for data recording and playback, information visualization, and air traffic generation. Software reliability, safety, and latency are some of the critical design considerations in development of the testbed.

LVC-DE↗
NASA NTRS1991

Composite load spectra for select space propulsion structural components

The objective of this program is to develop generic load models with multiple levels of progressive sophistication to simulate the composite load spectra that are induced in space propulsion system components, representative of Space Shuttle Main Engines (SSME), such as transfer ducts, turbine blades, and liquid oxygen (LOX) posts and system ducting. These models will be developed using two independent approaches. The first approach consists of using state-of-the-art probabilistic methods to describe the individual loading conditions and combinations of these loading conditions to synthesize the composite load spectra simulation. The methodology required to combine the various individual load simulation models (hot-gas dynamic, vibrations, instantaneous position, centrifugal field, etc.) into composite load spectra simulation models will be developed under this program. A computer code incorporating the various individual and composite load spectra models will be developed to construct the specific load model desired. The second approach, which is covered under the options portion of the contract, will consist of developing coupled models for composite load spectra simulation which combine the (deterministic) models for composite load dynamic, acoustic, high-pressure and high rotational speed, etc., load simulation using statistically varying coefficients. These coefficients will then be determined using advanced probabilistic simulation methods with and without strategically selected experimental data. This report covers the efforts of the third year of the contract. The overall program status is that the turbine blade loads have been completed and implemented. The transfer duct loads are defined and are being implemented. The thermal loads for all components are defined and coding is being developed. A dynamic pressure load model is under development. The parallel work on the probabilistic methodology is essentially completed. The overall effort is being integrated in an expert system code specifically developed for this project.

Newell, J. F.↗
NASA NTRS2013

Real-Time and High-Fidelity Simulation Environment for Autonomous Ground Vehicle Dynamics

This paper reports on a collaborative project between U.S. Army TARDEC and Jet Propulsion Laboratory (JPL) to develop a unmanned ground vehicle (UGV) simulation model using the ROAMS vehicle modeling framework. Besides modeling the physical suspension of the vehicle, the sensing and navigation of the HMMWV vehicle are simulated. Using models of urban and off-road environments, the HMMWV simulation was tested in several ways, including navigation in an urban environment with obstacle avoidance and the performance of a lane change maneuver.

vehicle sensing↗
NASA NTRS2013

Real-Time and High-Fidelity Simulation Environment for Autonomous Ground Vehicle Dynamics

This paper reports on a collaborative project between U.S. Army TARDEC and Jet Propulsion Laboratory (JPL) to develop a unmanned ground vehicle (UGV) simulation model using the ROAMS vehicle modeling framework. Besides modeling the physical suspension of the vehicle, the sensing and navigation of the HMMWV vehicle are simulated. Using models of urban and off-road environments, the HMMWV simulation was tested in several ways, including navigation in an urban environment with obstacle avoidance and the performance of a lane change maneuver.

unmanned ground vehicle (UGV)↗
NASA NTRSDate not supplied

Advanced Turboprop Transport Aircraft Modeling for the Electrified Powertrain Flight Demonstration Project

The objective of this study is to establish models for state of the art, representative regional non-electrified turboprop configurations in the 19-50 passenger capability range and assess performance impacts from advanced aircraft technologies. Two of these models will serve as reference baseline configurations for comparison to electrified aircraft propulsion (EAP) demonstrator concepts for the Electrified Powertrain Flight Demonstration (EPFD) project. The other two non-electrified configurations will primarily assess the impacts of advanced technologies on fuel consumption and CO₂ emissions. This paper details an aircraft synthesis and performance analysis approach using the General Aviation Synthesis Program (GASP) which is used to establish baseline performance capabilities, calibrate airplane and engine models using published manufacturer data and conduct technology sensitivity studies. Advanced technologies are selected from the categories of propulsion, aerodynamics, and flight systems. Performance assessments use Monte Carlo method coupled with GASP simulations to obtain performance distributions of the expected fuel burn, propulsive, aerodynamic, and weight benefits on the representative turboprop configurations from the application of advanced technologies. The final paper will present the impact of the advanced technologies on fuel burn and CO₂ emissions.

aircraft performance↗
DOE OSTI2022

Thermal design analysis for SuperTruck II lithium-titanate battery pack

Here, this paper presents a systematic thermal management analysis for a new lithium-titanate-oxide battery pack to be installed in a SuperTruck II, Class 8 hybrid truck. The authors investigate the feasibility of mounting the battery pack inside the vehicle and air-cooling it with fans supplying conditioned air from the cabin. Moreover, the cells within each module are to be immersed in a heat-transfer fluid to improve temperature homogeneity. A multi-stage thermal analysis is performed to ensure adequate thermal regulation of the battery under the proposed design, considering installation and operational constraints. The authors perform thermal and electrical characterization tests on a single cell. Results inform the development of computational fluid dynamics models of the cells, modules, and pack. Module-level analysis shows that the cell temperatures can be maintained below their upper operational limit of 55 °C with module wall-to-air heat transfer coefficients between 10 and 20 Wm -2 K -1 . Pack-level analysis of distinct configurations determines effective airflow paths for adequate heat transfer and delivers a final battery pack design that achieves sufficient cooling and temperature uniformity. A reduced-order electrothermal model is developed to rapidly predict the transient battery performance and to develop a temperature control strategy.

25 ENERGY STORAGE↗
DOE OSTI2026

Understanding Electric Vehicle Range and Charging Needs: Interactions Between Ambient Temperature, Commute Patterns, and State-of-Charge Usage

Electric vehicle (EV) performance can vary substantially under real-world operating conditions, particularly due to ambient temperature effects on energy consumption, battery behavior, and thermal management requirements. This study quantifies how weather conditions, daily driving patterns, and State-of-Charge (SOC) usage strategies jointly influence EV driving range, charging frequency, and overall energy efficiency. A detailed and experimentally validated Autonomie vehicle model is developed, integrating a powertrain, a mono-zonal cabin model, and a battery electro-thermal model. Three battery sizes (200-, 300-, and 400-mile homologated ranges) are assessed across five commute profiles (20–200 miles) and six ambient temperatures (−18 °C to 50 °C), including scenarios with and without preconditioning. Results show that extreme temperatures could significantly decrease the maximum achievable range by up to 55% in cold conditions (−18 °C) and 40% in hot conditions (50 °C), relative to moderate conditions. Larger battery packs retain a greater fraction of their nominal range under thermal stress, while smaller packs experience sharper relative penalties due to the higher contribution of thermal loads to total energy demand. The analysis further demonstrates that limiting operation to partial SOC windows (e.g., 80–20%), a common real-world practice, significantly reduces achievable range and increases charging frequency, particularly in cold weather. Thermal preconditioning while plugged in is shown to mitigate these effects for short trips, reducing energy consumption by up to 31% in hot conditions and 7% in cold conditions. The findings demonstrate how climate, SOC usage behavior, and thermal management jointly shape the practical driving capability of EVs, highlighting the importance of efficient thermal management and realistic user charging strategies for ensuring reliable EV operation across diverse climatic scenarios.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1972

A study of internal drag of small-scale ducts at Mach number 4

An experimental investigation was made to examine the applicability of methods used to determine internal drag of small ducts and to study some of the problems encountered in assessing momentum losses in such ducts. Test Mach numbers ranged from 3.7 to 4.4 at angles of attack of 0 and 5 degrees and at a constant Reynolds number of 4.3 million per foot. The configurations represented small ducts used to simulate external aerodynamics of air breathing propulsion systems and consisted of wing nacelle models of ducts with circular, square, and rectangular inlets and with a two-dimensional inlet.

Graham, L. A.↗
NASA NTRS1977

Space Shuttle Program Progress Report

A status report is presented on progress in the design, manufacturing and testing of components of the space transportation system (STS), and primarily the Space Shuttle vehicles. Project landmarks from 1969 to 1981 are indicated, fabrication of the Shuttle Orbiter and rollout of the first prototype are described, fabrication and assembly of some Orbiter parts are sketched, and some of the subsystems (thermal protection, avionics, maneuvering aids, reaction control, remote manipulator) are described. Also discussed are: Orbiter carrier aircraft, Shuttle main engine and tests, external fuel tank, solid rocket booster, launch and landing facilities. A separate section is devoted to ground tests (vibration, propulsion, electronics, avionics integration), trainers and simulators, and flight tests (captive flight, free flight, landing and approach, orbital flight).

Thompson, R. F.↗
NASA NTRS1978

Fourth NASA Inter-Center Control Systems Conference

Space vehicle control applications are discussed, along with aircraft guidance, control, and handling qualities. System simulation and identification, engine control, advanced propulsion techniques, and advanced control techniques are also included.

Source record↗
NASA NTRS1989

Thermal design for the Comet Rendezvous Asteroid Flyby spacecraft

The mission overview of the Comet Rendezvous Asteroid Flyby (CRAF) spacecraft, which is planned to rendezvous with Comet Kopff in 1998, is presented, together with the CRAF mission trajectory. The preliminary thermal design of the CRAF spacecraft is discussed, with emphasis placed on the Low Precision Pointing Platform, Bus, Propulsion Module, and Comet Penetrator, the thermal design of which was impacted most by the comet environment. Model simulations showed the design of the bus and the propulsion module subsystems to be adequate. Configuration diagrams are included.

Tsuyuki, G. T.↗
NASA NTRS1991

Predictive control and estimation algorithms for the NASA/JPL Deep Space Network antennas

A modified output prediction procedure, and a new controller design based on the predictive control law are presented. Also, the predictive estimator is developed to complement the controller, and to enhance the system performance. The predictive controller was designed and applied to the tracking control of the National Aeronautics and Space Administration (NASA)/Jet Propulsion Laboratory (JPL) 70-m antenna. Simulation results show significant improvement in tracking performance over the linear quadratic controller and estimator presently in use.

Gawronski, W.↗
NASA NTRS2005

A Dual-Use Ballute For Entry And Descent During Planetary Missions

An inflatable ballute system for aerocapture at the atmosphere-bearing planets and at Titan may provide significant performance benefits, compared to conventional propulsive capture and aerocapture technologies. Ballute simulations to date release the ballute at the appropriate instant and then ignore it to focus on the trajectory of the orbiter. The latest concept, which we pursue in this paper, is to employ the ballute to soft-land a small payload. Thus the same ballute can provide two uses (1) aerocapture of the orbiter and (2) soft-landing of the lander package, hence the term dual-use ballute. The dual-use ballute concept has the potential to dramatically alter the way we approach exploration of the atmosphere-bearing bodies in the Solar System. Cases investigated here include aerocapture and soft-landing at Mars, Titan and Neptune.

Medlock, Kristin L.↗
NASA NTRS2018

Experimental Evaluation of BLI Propulsion: The Boundary Layer Ingesting Inlet/Distortion-Tolerant Fan Solution

NASA has successfully developed a new testbed configuration for experimentally evaluating embedded boundary layer ingesting aircraft propulsors in its 8'x6' Supersonic Wind Tunnel. This testbed meets the challenges of providing the necessary freestream flow Mach conditions and desired range and distribution of boundary layer thickness for embedded aircraft propulsion systems. The testbed consists of a 48ft long raised wind tunnel floor aircraft surface simulator and a boundary layer regulation system to produce propulsion-local aircraft aerodynamic flow fields. This durable special test equipment is designed to be installed in the wind tunnel's transonic test section and is capable of evaluating a wide range of subcritical and supercritical airframe-propulsion integration configurations for subsonic cruise aircraft. The wind tunnel and testbed are well suited for meeting the test requirements of these propulsors in the most cost efficient way and has been aerodynamically calibrated and proven through tests of a first-of-its-kind boundary layer ingesting propulsor.

Arend, David J.↗
NASA NTRS2020

eVTOL Passenger Acceptance

With the expected introduction of electric vertical takeoff and landing (eVTOL) aircraft for urban air mobility (UAM) services, passenger acceptance has become an issue of interest to manufacturers and operators. This study took an initial look at what passengers expect from an eVTOL UAM flight experience – what aspects matter most, what might be acceptable, and where there are gaps in our understanding. The analysis included a literature search and interviews with experts from the aviation community to identify passenger concerns and potential mitigations. Passenger concerns were found to fall into six general categories: perceived safety, noise and vibration, availability and access, passenger well-being, concern for the environment, and vehicle motion. The study used a modified quality function deployment approach to correlate these passenger concerns with design and operational variables, highlighting how design and operational parameters can mitigate the passenger concerns. NASA research can address the passenger concerns by developing simulation capabilities and noise models, characterizing propulsion system performance, taking direct measurem and conducting further studies of market demand and design methods.

Edwards, Thomas↗
NASA NTRSDate not supplied

Dynamic Vehicle Assessment for Intelligent Contingency Management of Urban Air Mobility Vehicles

New algorithms will be required to ensure passenger and bystander safety during the expected era of autonomous urban air mobility (UAM) aircraft. This paper examines an approach for assessing the vehicle capability to fly itself and to complete a mission safely. The concepts combine elements of system identification, adaptive control, flight dynamics, envelope predictions, and handling qualities, as well as human pilot intuition. The approach is applied to a simulation of a generic distributed electric propulsion urban air mobility-type aircraft, which was developed under the NASA Transformational Tools and Technologies (TTT) project, Autonomous Systems / Intelligent Contingency Management subproject.

flight envelope↗