Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Power Tower”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

High Toughness Cermets for Molten Salt Pumps

Concentrated Solar Power plants using nitrate salts used cantilevered pump designs to avoid use of bearings in the 565°C salt; however, this necessitated the use of a sump that added additional cost, complexity, and thermal losses. Sump systems had their own complications, including risk of flooding the sump due to control issues either with level indicators or failures in the control valve responsible for filling the sump. Long-shafted pumps were developed and tested, and they outline the need to develop journal sleeves and bearings for new salt systems. Based on reports, pumps will need to be a vertical single- or multi-stage type, mounted to the roof of the molten salt tanks. Design and service for molten salt pumps above 550°C is relatively limited, and at temperatures up to 750°C there is no available design or service experience. Long-shaft pumps that extend to the bottom of the thermal energy storage tank will require bearing materials that are suitable to the given salt chemistry. Lubricity of proposed salts is unclear and need to be determined, especially for cold-tank pumps that require multi-stages for lifting the salt to the top of the tower. Materials, design, and maintenance are all major unknowns.

14 SOLAR ENERGY↗

Roadmap to Advance Heliostat Technologies for Concentrating Solar-Thermal Power

Heliostat-based concentrating solar-thermal power (CSP) systems can offer immense potential to provide low-cost, dispatchable renewable thermal and electrical energy to help achieve 100% decarbonized energy infrastructure in the United States. Heliostats are a major capital cost technology and a performance-dominating component of state-of-the-art commercial molten salt towers and Generation 3 CSP systems. In 2021, the U.S. Department of Energy (DOE) Solar Energy Technologies Office (SETO) launched the Heliostat Consortium (HelioCon), a five-year initiative to advance heliostat technologies. The HelioCon mission is threefold: (1) establish strategic core testing and modeling capabilities and infrastructure at national labs; (2) support heliostat technology development in relevant industries; and (3) serve as a central repository to integrate industry, academia, and other stakeholders for heliostat technology research, development, validation, and deployment. In this report, HelioCon presents a roadmapping study on advancing heliostat technologies, intended as a central reference for the whole CSP community.

14 SOLAR ENERGY↗

Tuning of Nacelle Feedback Gains for Floating Wind Turbine Controllers Using a Two-DOF Model

Designing a collective blade pitch controller for floating offshore wind turbines (FOWTs) poses unique challenges due to the interaction of the controller with the dynamics of the platform. The controller must also handle the competing objectives of power production performance and fatigue load management. Existing solutions either detune the controller with the result of slowed response, make use of complicated tuning methods, or incorporate a nacelle velocity feedback gain. With the goal of developing a simple control tuning method for the general FOWT researcher that is easily extensible to a wide array of turbine and hull configurations, this last idea is built upon by proposing a simple tuning strategy for the feedback gain. This strategy uses a two degree-of-freedom (DoF) turbine model that considers tower-top fore-aft and rotor angular displacements. For evaluation, the nacelle velocity term is added to an existing gain scheduled proportional-integral controller as a proportional gain. The modified controller is then compared to baseline land-based and detuned controllers on an example system for several load cases. First-pass results are favorable, demonstrating how researchers can use the proposed tuning method to efficiently schedule gains for adequate controller performance as they investigate new FOWT configurations.

49 EE - Wind and Water Power Program - Wind (EE-4W↗

A Techno-Economic Analysis of a 50MWth Light-Trapping Cavity-Planar Solar Receiver Tower Capital Expenditures and its Cost Mitigation Strategies

To maximize thermal efficiency, the National Renewable Energy Laboratory (NREL) has proposed a light-trapping cavity-planar receiver design intended to capture energy from reradiating surfaces. This system implements a macroscale light trapping mechanism induced by panels with triangular channels, this mechanism allows for elevated temperatures on the receiver panels and in turn the temperature of the HTF; using this design coupled with the implementation of a fluidized particle flow as the HTF, it can be expected for some components to reach a peak working temperature of nearly 1000 degrees C cyclically throughout each day-night cycle. While these temperatures correlate to higher efficiency of the CSP tower they also demand intense thermomechanical properties from the materials used to make the receiver panels. In this analysis, we will list our assumptions to provide clarity on the significance of our calculation. This cost analysis will be conducted using a combination of both case study data and surveying industry to determine costs that are relevant to the current market trends. This analysis represents an early attempt to establish the Capital Expenditures required for a CSP tower of such design to determine the feasibility of implementing such a system in the industry.

concentrated solar power (CSP)↗

Structural analysis of wind turbine rotors for NSF-NASA Mod-0 wind power system

Preliminary estimates of vibratory loads and stresses in hingeless and teetering rotors for the proposed 100-kW wind power system are presented. Stresses in the shank areas of the 19-m (62.5-ft) blades are given for static, rated, and overload conditions. The teetering rotor has substantial advantages over the hingeless rotor with respect to shank stresses, fatigue life, and tower loading. A teetering rotor will probably be required in order to achieve a long service life in a large wind turbine exposed to periodic overload conditions.

Spera, D. A.↗

Methods of attenuating wind turbine ac generator output variations

Wind speed variation, tower blockage and structural and inertial factors produce unsteady torque in wind turbines. Methods for modifying the turbine torque so that steady torque is delivered to the coupled ac generator are discussed. The method that may evolve will be influenced by the power use that develops and the trade-offs of cost, weight and complexity.

Gold, H.↗

A HIRF-Map Certification Approach for UAM, AAM, and UAS Vehicles

Advanced Air Mobility (AAM), Urban Air Mobility (UAM), and Unmanned Aerial Systems (UAS) vehicles will fly in airspace similar to Transport Category Rotorcraft, requiring them to meet stringent requirements for High-Intensity Radiated Fields (HIRF) certification. The environment is notably severe, particularly compared to fixed-wing aircraft, due to operations at lower altitudes. This potentially exposes the vehicles to high-power transmitters on the ground, leading to significant challenges. High-level HIRF exposure can result in avionic system upsets, interference, and undesirable effects. Shielding and circuit protection against HIRF pose significant barriers concerning size, weight, and cost, especially for emerging electric vertical take-off and landing (eVTOL) and electric short take-off and landing (eSTOL) vehicles. This paper proposes a novel HIRF protection approach, aiming to reduce costs by certifying vehicles to a "vehicle tolerance level" lower than that required for Transport Category Rotorcraft. The remaining protection is achieved by maintaining a safe distance from known HIRF sources. This distance is calculated based on the vehicle's tolerance level and transmitter characteristics, such as transmit power, antenna beamwidth, and direction. Tailored flight maps are developed to identify transmitters and avoidance zones within an operating area or along a flight path, enabling restricted vehicle operations. Vehicles with higher tolerance levels could have smaller HIRF avoidance zones, allowing them to operate closer to transmitters. Transmitter data are sourced from government databases, such as those of the Federal Communications Commission (FCC) and the National Oceanic and Atmospheric Administration (NOAA). A map tool is developed using Matlab to calculate and visualize HIRF avoidance zones based on available databases. The tool determines stand-off distances based on input vehicle tolerance levels, displaying results on various base maps depicting HIRF-restricted areas. Illustrations cover various FCC transmitters, including AM/FM/TV transmitters, satellite earth stations, and NOAA weather radars. The HIRF zones of smaller transmitters, such as land-mobile radios, pagers, microwave links, and cellular towers, are also illustrated. An example of flight planning around transmitters is provided. For now, airports and government-owned lands are excluded due to limited access to sensitive transmitter data. Despite this approach, a minimum HIRF tolerance level for vehicles may still be necessary to cover mobile devices, cellular base stations, transmitters on other AAM vehicles, and other small power devices not included in the FCC databases. The paper discusses findings and areas for improving existing databases and suggests an approach for better access to sanitized data in more restricted government databases. This method significantly deviates from the standard approach and introduces slightly higher flight-planning complexity. However, the potential cost savings are considerable. Future AAM/UAM/UAS aeronautical charts could potentially incorporate these new HIRF avoidance zones. Keywords—HIRF; Map; AAM; UAM; UAS; Advanced Air Mobility; Urban Air Mobility; Unmanned Aerial Systems; Certification.

HIRF↗

System and Component Transport Considerations of Micro-Pin Based Solar Receivers With High Temperature Gaseous Working Fluids

This paper explores the interactions between micro-pin concentrated receiver designs with overall solar thermal energy system performance, with different operating conditions, working fluid, and required materials of construction. A 320 MW thermal plant coupled to a 160 MW electric sCO2 Brayton cycle is considered as the baseline. The circulating fluid enters the receiver at 550°C, and leaves at 720°C. The thermal storage/power block are located 150 m from the receiver at the base of the receiver tower. A resistance network based thermal and hydraulic model is used to predict heat transfer and pressure drop performance of the micro-pin receiver. This output of this model is coupled to a system level model of the pressure loss and compressor power required in the remainder of the high temperature gas loop. Overall performance is investigated for supercritical carbon dioxide and helium as working fluids, at pressures from 7.5 to 25 MPa, and at delivery temperatures of 720°C. The results show that by modifying pin depth and flow lengths, there are design spaces for micro-pin devices that can provide high thermal performance without significantly reducing the overall solar thermal system output at lower operating pressures. Use of lower pressure fluids enables lower cost materials of construction in the piping and distribution system, reducing the cost of electricity.

14 SOLAR ENERGY↗

Evaluation of a Magneto-optical Filter and a Fabry-perot Interferometer for the Measurement of Solar Velocity Fields from Space

A program was developed to evaluate the performance of three different devices as possible space-borne solar velocity field imagers. Two of these three devices, a magneto-optical filter and a molecular adherence Fabry-Perot interferometer were installed in a newly-constructed observing system located at the 60-foot tower telescope at the Mt. Wilson Observatory. Time series of solar filtergrams and Dopplergrams lasting up to 10 hours per day were obtained with the filter while shorter runs were obtained with the Fabry-Perot. Two-dimensional k (sub h)-omega power spectra which show clearly the well-known p-mode ridges were computed from the time series obtained with the magneto-optical filter. These power spectra were compared with similar power spectra obtained recently with the 13.7-m McMath spectrograph at Kitt Peak.

Rhodes, E. J., Jr.↗

Solar power satellite offshore rectenna study

It was found that an offshore rectenna is feasible and cost competitive with land rectennas but that the type of rectenna which is suitable for offshore use is quite different from that specified in the present reference system. The result is a nonground plane design which minimizes the weight and greatly reduces the number of costly support towers. This preferred design is an antenna array consisting of individually encapsulated dipoles with reflectors supported on feed wires. Such a 5 GW rectenna could be built at a 50 m water depth site to withstand hurricane and icing conditions for a one time cost of 5.7 billion dollars. Subsequent units would be about 1/3 less expensive. The east coast site chosen for this study represents an extreme case of severe environmental conditions. More benign and more shallow water sites would result in lower costs. Secondary uses such as mariculture appear practical with only minor impact on the rectenna design. The potential advantages of an offshore rectenna, such as no land requirements, removal of microwave radiation from populated areas and minimal impact on the local geopolitics argue strongly that further investigation of the offshore rectenna should be vigorously pursued.

Source record↗

Validation of new and existing methods for time-domain simulations of turbulence and loads

We seek to obtain a second-by-second match between the simulated and measured structural loads of a utility-scale wind turbine. To obtain the one-to-one load simulations, we start with the furthest upstream component of the modeling chain: the turbulent inflow. We consider new and existing methods to generate constrained-turbulence flow fields. The new method is based on large-eddy simulations (LES) and machine learning (ML). The existing methods include Kaimal-based TurbSim and the superstatistical wind field model. The inflow measurements used to constrain these simulations are obtained with a nacelle-mounted scanning lidar. We compare the flow fields for the different inflow simulation approaches and validate their associated load predictions against measurements collected in the Rotor Aero-dynamics, Aeroelastics, and Wake (RAAW) field campaign. We find that the rotor-position control developed for this study is key in enabling the time match between measurements and simulations. When this control approach is used, the load simulation performance tracks with the inflow simulation fidelity, with LES+ML yielding errors ≤ 4% for the damage-equivalent loads of flapwise bending moment, and tower fore-aft bending moments.

17 WIND ENERGY↗

The role of wind tunnel models in helicopter noise research

A study was conducted to determine the applicability of using small-scale powered helicopter models operating in nonanechoic wind tunnels to predict the sound pressure levels of full-scale rotor harmonic noise components. The investigation included noise generation due to high-tip-speed effects, tandem-rotor blade/vortex interactions, single rotors operating on test towers, and the interaction between main rotor vortices and tail rotors. In all cases it was found that the pressure time history waveforms characteristic of different noise-generating mechanisms were properly reproduced by the models. Corrections for microphone locations, acoustical reverberation, and tunnel wind velocity were developed. Application of these corrections to the model data were found to yield satisfactory correlation with full-scale sound pressure levels except for the isolated single rotor, where highly transient data, both model and full-scale, recluded good agreement of absolute values.

Sternfeld, H., Jr.↗

NGEE Arctic Soil Micro-warming Experiment Temperature Profiles, Council Road Mile Marker 71, Seward Peninsula, Alaska, 2017-2019

The reported soil temperature profile measurements (24 locations - 2 probes with 5 and 6 thermistors, respectively - Fig. 1 and Fig. 2) were initiated as part of a soil micro-warming experiment at the Council Road Mile Marker 71 Site (CN_MM71) in September 2017. From 2017 through August 2019, these were measurements of ambient pre-treatment plot conditions. This tussock tundra site (with underlying permafrost) experiences annual frost heaving that causes a vertical movement of the ground surface, hence causing some of the upper most temperature thermistors to be at surface level or above ground and recorded therefore air temperatures near the surface and not below ground soil temperature (see section on Quality Assurance). After August 2019, these measurements ended in preparation for transitioning to the experimental warming of individual plots. The reported temperature data are nominally 3-hour averages of measurements made at varying frequencies (3-hour maximum) with frequencies that depended upon power (solar) availability to operate the sensors (see section in documentation on Methods). The number of values and the standard deviation for each 3-hour average (where appropriate) are also provided. These measurements are located near the NGEE-Arctic CO2 and CH4 eddy covariance tower at the Council Road Site (US-NGC: NGEE Arctic Council, https://ameriflux.lbl.gov/sites/siteinfo/US-NGC#overview) and auxiliary data at https://doi.org/10.5440/1526749. This dataset contains four *.csv files and one *.pdf file. The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗

Experiments on thermoacoustic convection heat transfer in gravity and zero-gravity environments

The results of an experimental study of thermoacoustic convection (TAC) heat transfer in gravity and zero-gravity environments are presented. The experimental apparatus consisted of a cylinder containing air as the compressible fluid. The enclosed air was heated electrically at the top surface which consisted of a thin high-resistance steel foil connected to a power source. Thermocouples were used to measure the transient temperature of the air on the axis of the cylinder and the heated surface in the both zero-gravity and gravity environments. The zero-gravity tests were performed in the Zero-Gravity Drop Tower Facility of NASA-Lewis Research Center. The experimental results were corrected for the error due to radiation absorption by the thermocouples. A conduction-only numerical heat transfer model was developed to compute the transient air temperature in the cylindrical geometry. The results were compared to the experimental data to determine the significance of the thermoacoustic convection heat transfer mechanism. It is observed that the rate of heat transfer to the air measured during the experiments is consistently higher than that obtained by the conduction-only solution indicating a significant presence of the TAC heat transfer. Further experiments are planned to measure directly (1) the radiative heat transfer contribution to the rise in the air temperature, and (2) the air pressure oscillations within the cylinder that are responsible for the convective heat transfer mode.

Parang, Masood↗

Energy efficiency of blower heater non-purge compressed air dryers

This research focuses on twin tower regenerative closed loop desiccant dryers, specifically: blower heater non-purge (BHNP) with and without cooling water pumps, compressed-air heater purge (CHP), blower heater purge (BHP) and pressure swing heaterless (PSH). The research was conducted by collecting and analysing real time current draw data on air compressors and associated dryers at eight different facilities (13 air compressors) in terms of energy, power and cost. A decision tool was developed to depict the operational characteristics (power, energy and cost) of each type of dryer if used in conjunction with the selected compressor system. Finally, this research, on an equivalent normalised basis, compared and contrasted the different types of dryers in terms of performance and cost. Here, the research concluded that of the five types of desiccant dryer types observed the most energy efficient was the BHNP (with cooling water pump), subject to the operational conditions.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Packed and fluidized bed absorber modeling for carbon capture with micro-encapsulated sodium carbonate solution

Micro-Encapsulated CO 2 Sorbents (MECS) are a promising technology for post-combustion carbon capture because they enable slow-reacting solvents like carbonate solution to compete with traditional amine solvents. Before scaling up MECS for pilot testing, modeling is needed to design a MECS absorber and quantify its size and energy penalty. To that end, a multi-scale model for MECS- that ranges from a single capsule to a 500 MWe power plant absorber- is developed and presented here in this paper. First, the individual capsule model is developed and fitted to experimental CO 2 absorption data collected on a 0.1 g sample of capsules filled with sodium carbonate solution. This capsule model is then validated against data collected on a 25 g batch of capsules exposed to flue gas conditions in a fluidized column. This model is then scaled up to represent two absorber designs: a multi-stage, counter-flow fluidized bed and a hollow, cylindrical packed bed with radial gas flow. These two absorber bed models are first optimized for a 1 MWe pilot-scale absorber, and then optimized for a 500 MWe coal plant. This model predicts absorbers of similar dimensions and smaller energy penalties than previously modeled absorbers filled with amine solvent capsules. Furthermore, it is demonstrated here that a few reasonable improvements to capsule design would result in absorber sizes and energy penalties lower than those of a benchmark amine solvent tower. These results demonstrate that micro-encapsulated carbonate solution can compete with faster-acting amine solvents for post-combustion carbon capture.

20 FOSSIL-FUELED POWER PLANTS↗

The hydrogen sulfide emissions abatement program at the Geysers Geothermal Power Plant

The scope of the hydrogen sulfide (H2S) abatement program at The Geysers Geothermal Power Plant and the measures currently under way to reduce these emissions are discussed. The Geysers steam averages 223 ppm H2S by weight and after passing through the turbines leaves the plant both through the gas ejector system and by air-stripping in the cooling towers. The sulfide dissolved in the cooling water is controlled by the use of an oxidation catalyst such as an iron salt. The H2S in the low Btu ejector off gases may be burned to sulfur dioxide and scrubbed directly into the circulating water and reinjected into the steam field with the excess condensate. Details are included concerning the disposal of the impure sulfur, design requirements for retrofitting existing plants and modified plant operating procedures. Discussion of future research aimed at improving the H2S abatement system is also included.

Allen, G. W.↗