Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Porous Polymer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Investigation of porous polydimethylsiloxane structures with tunable properties induced by the phase separation technique

This article reports the fabrication and characterization of porous polydimethylsiloxane (PDMS) structures developed by the solvent evaporationinduced phase separation technique. Here, ternary systems containing water/ tetrahydrofuran (THF)/PDMS with various concentrations are produced to form a stable solution. The porous PDMS structures are formed by removing the solvent (THF) and nonsolvent (water) phases during the stepping heat treatment procedure. The analytical ternary phase diagram is constructed based on the thermodynamic equilibrium state in the polymer solution to explain the stable/unstable formulations and the possible composition change path. The results show that the isolated pores with the adjustable pore size ranging from 330 to 1900 μm are obtained by tuning the water to the THF ratio. The mechanical properties of the porous PDMS structures are determined by conducting the tensile tests on the prepared dog bone-shaped specimens. A wide range of elastic modulus ranging between 0.49 and 1.05 MPa was achieved without affecting the density of the porous sample by adjusting the solvent and non-solvent content in the solution. It is shown that the flexibility of the porous structures can be improved by reducing the ratio of water to THF and decreasing the PDMS content. The porosity measurements reveal that the PDMS concentration is the major phase controlling the porosity of the structure, while the effect of water/THF is negligible.

42 ENGINEERING↗

Molecularly Mixed Composite Membranes: Challenges and Opportunities

The fabrication of porous molecules, such as metal–organic polyhedra (MOPs), porous organic cages (POCs) and others, has given rise to the potential for creating “solid solutions” of molecular fillers and polymers. Such solid solutions circumvent longstanding interface issues associated with mixed matrix membranes (MMMs), and are referred to as molecularly mixed composite membranes (MMCMs) to distinguish them from traditional two-phase MMMs. Early investigations of MMCMs highlight the advantages of solid solutions over MMMs, including dispersion of the filler, anti-plasticization of the polymer network, and removal of deleterious interfacial issues. However, the exact microscopic structure as well as the transport modality in this new class of membrane are not well understood. Moreover, there are clear engineering challenges that need to be addressed for MMCMs to transition into the field. Finally in this Minireview, the authors outline several scientific and technological challenges associated with the aforementioned questions and their suggestions to tackle them.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Novel Polyethylenimine–Acrylamide/SiO 2 Hybrid Hydrogel Sorbent for Rare-Earth-Element Recycling from Aqueous Sources

Recycling rare earth elements (REEs) becomes increasingly important due to their supply vulnerability and increasing demands in industry, agriculture, and national security. Hybrid hydrogel sorbents were outstanding due to their high stability and selectivity. Organic-inorganic hybrid hydrogels were synthesized by thermo-polymerization of acrylamide onto PEI polymer chain with N,N’-methylene bisacrylamide as a crosslinker. The grafted network was evidenced by DRIFTS and XPS. The porous structure was observed by SEM. Crosslink degree, PEI grafting degree, and SiO 2 concentration were studied to optimize the REEs adsorption. The pH value of the medium greatly affected REE adsorption capacity, where the nearly neutral conditions gave the strongest bonding of REEs to active sites. Moreover, kinetic studies showed that the rate-determining step of the adsorption process was chemical sorption, and that REE diffusion within micropores was the control step for, specifically, intraparticle diffusion. The adsorbents showed excellent selectivity and recyclability for REEs through 5 adsorption-desorption cycles in contact with synthetic acid mine drainage solution. A high separation toward REEs over fouling metals was achieved by using a citrate-based buffer eluent solution. This hybrid hydrogel shows promise for the recycling of REEs from aqueous solutions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High Temperature Aerogels for Thermal Protection Systems

High temperature aerogels in the Al2O3-SiO2 system are being investigated as possible constituents for lightweight integrated thermal protection system (TPS) designs for use in supersonic and hypersonic applications. Gels are synthesized from ethoxysilanes and AlCl3.6H2O, using an epoxide catalyst. The influence of Al:Si ratio, solvent, water to metal and water to alcohol ratios on aerogel composition, morphology, surface area, and pore size distribution were examined, and phase transformation on heat treatment characterized. Aerogels have been fabricated which maintain porous, fractal structures after brief exposures to 1000 C. Incorporation of nanofibers, infiltration of aerogels into SiC foams, use of polymers for crosslinking the aerogels, or combinations of these, offer potential for toughening and integration of TPS with composite structure. Woven fabric composites having Al2O3-SiO2 aerogels as a matrix also have been fabricated. Continuing work is focused on reduction in shrinkage and optimization of thermal and physical properties.

Hurwitz, Frances I.↗

Nanostructured Lanthanum Halides and CeBr3 for Nuclear Radiation and Detection

Scintillator materials are used to detect, and in some cases identify, gamma rays. Higher performance scintillators are expensive, hard to manufacture, fragile, and sometimes require liquid nitrogen or cooling engines. But whereas lower-quality scintillators are cheap, easy to manufacture, and more rugged, their performance is lower. At issue: can the desirable qualities of high-and low-performance scintillators be combined to achieve better performance at lower cost? Preliminary experiments show that a LaF{sub 3}:Ce oleic acid-based nanocomposite exhibits a photopeak when exposed to {sup 137}Cs source gamma-radiation. The chemical synthesis of the cerium-doped lanthanum halide nanoparticles are scalable and large quantities of material can be produced at a time, unlike typical crystal growth processes such as the Bridgeman process. Using a polymer composite (Figure 1), produced by LANL, initial measurements of the unloaded and 8% LaF{sub 3}:Ce-loaded sample have been made using {sup 137}Cs sources. Figure 2 shows an energy spectrum acquired for CeF{sub 3}. The lighter plot is the measured polymer-only spectrum and the black plot is the spectrum from the nanocomposite scintillator. As the development of this material continues, the energy resolution is expected to improve and the photopeak-to-Compton ratio will become greater at higher loadings. These measurements show the expected Compton edge in the polymer-only sample, and the Compton edge and photo-peak expected in the nanophosphor composites that LANL has produced. Using a porous VYCORR with CdSe/ZnS core shell quantum dots, Letant has demonstrated that he has obtained signatures of the 241Am photopeak with energy resolution as good at NaI (Figure 3). We begin with the fact that CeBr{sub 3} crystals do not have a self-activity component as strong as the lanthanum halides. The radioactive 0.090% {sup 138}La component of lanthanum leads to significant self-activity, which will be a problem for very large detector volumes. Yet a significant strength of the nanostructure detector concept is the ability to create extremely large detector volumes by mixing nanoparticles into a transparent matrix. This would argue for use of nanoparticles other than lanthanum halides. Nanocomposites are easy to prepare; it is much less costly to use nanocomposites than to grow large whole crystals of these materials. The material can be fabricated at an industrial scale, further reducing cost. This material potentially offers the performance of $300/cc material (e.g., lanthanum bromide) at a cost of $1/cc. Because the material acts as a plastic, it is rugged and flexible, and can be made in large sheets, increasing the sensitivity of a detector using it. It would operate at ambient temperatures. Very large volumes of detector may be produced at greatly reduced cost, enhancing the non-proliferation posture of the nation for the same dollar value.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Crystal-growth-dominated fabrication of metal-organic frameworks with orderly distributed hierarchical porosity

Constructing architectures with hierarchical porosity has been widely considered as the most efficient way to bypass the problems related to slow mass transfer and inaccessibility of internal space in MOFs. Now, a crystal-growth-dominated strategy is proposed to fabricate hierarchically porous MOFs (HP-MOFs). When the crystal growth is dominated by the monomer attachment, the aggregation of nonionic surfactant or polymer can be easily captured and released during the crystal growth process, resulting in the formation and ordering hierarchical pores along the radial direction. Furthermore, owing to the accelerated mass diffusion and more exposed active sites of this design, HP-MOFs exhibited an enhanced catalytic efficiency in styrene oxidation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tungsten-loaded SMP foam nanocomposites with inherent radiopacity and tunable thermo-mechanical properties

Shape memory polymer (SMP) foams have been developed for use in neurovascular occlusion applications. These materials are predominantly polyurethanes that are known for their biocompatibility and tunable properties. However, these polymers inherently lack X–ray visibility, which is a significant challenge for their use as implantable materials. Herein, low density, highly porous shape memory polyurethane foams were developed with tungsten nanoparticles dispersed into the foam matrix, at increasing concentrations, to serve as a radiopaque agent. Utilizing X–ray fluoroscopy sufficient visibility of the foams at small geometries was observed. Thermal characterization of the foams indicated altered thermal response and delayed foam actuation with increasing nanoparticle loading (because of restricted network mobility). Mechanical testing indicated decreased toughness and strength for higher loading because of disruption of the SMP matrix. Altogether, filler addition imparted x–ray visibility to the SMP foams and allowed for tuned control of the transition temperature and actuation kinetics for the material.

36 MATERIALS SCIENCE↗

Recovering carbon losses in CO 2 electrolysis using a solid electrolyte reactor

The practical implementation of electrochemical CO 2 reduction technology is greatly challenged by notable CO 2 crossover to the anode side, where the crossed-over CO 2 is mixed with O 2 , via interfacial carbonate formation in traditional CO 2 electrolysers. Here we report a porous solid electrolyte reactor strategy to efficiently recover these carbon losses. Furthermore, by creating a permeable and ion-conducting sulfonated polymer electrolyte between cathode and anode as a buffer layer, the crossover carbonate can combine with protons generated from the anode to re-form CO 2 gas for reuse without mixing with anodic O 2 . Using a silver nanowire catalyst for CO 2 reduction to CO, we demonstrated up to 90% recovery of the crossover CO 2 in an ultrahigh gas purity form (>99%), while delivering over 90% CO Faradaic efficiency under a 200 mA cm -2 current. A high continuous CO 2 conversion efficiency of over 90% was achieved by recycling the recovered CO 2 to the CO 2 input stream.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

EWTN: Quantifying Mass Transport to Enable Water Electrolyzer Architectures with Low Flow-Rate Sensitivity

To develop cost-effective and high-performing polymer electrolyte water electrolyzers (PEWEs) for gigawatt-scale applications, researchers have focused on reducing precious metal catalyst loadings and optimizing porous transport layers. However, the performance of PEWEs is also affected by system architecture. Mass transport losses are dependent on localized architecture and material interactions. In-situ measurements, such as current density distribution maps have demonstrated advantages in understanding the intricate characteristics and influence of two-phase flow within PEWEs. This study proposes the parameter of effective water transport number (EWTN) as a quantitative tool to investigate such current density distribution (CDD) measurements for PEWEs. Results show that higher flow-rates have EWTN values of 0.95 and above, indicating no mass transport limitations; while lower flow-rates with large gradients CDD have EWTN values between 0.6-0.8, indicating mass transport limited conditions. The new analysis also identified a correlation between mass transport losses due to bubble accumulation, membrane hydration, and ohmic overpotentials. To address these limitations, an unitized pin-type LGDL/flow-field design was developed, which effectively prevents local gas phase accumulation, resulting in improved mass transport characteristics. The results of this work show reduced flow-rate sensitivity with the pin-type architecture and ∼13% increased performance at 0.24 ml / min / cm 2 .

Electrochemistry↗

Theoretical performance of hydrogen-bromine rechargeable SPE fuel cell

A mathematical model was formulated to describe the performance of a hydrogen-bromine fuel cell. Porous electrode theory was applied to the carbon felt flow-by electrode and was coupled to theory describing the solid polymer electrolyte (SPE) system. Parametric studies using the numerical solution to this model were performed to determine the effect of kinetic, mass transfer, and design parameters on the performance of the fuel cell. The results indicate that the cell performance is most sensitive to the transport properties of the SPE membrane. The model was also shown to be a useful tool for scale-up studies.

Savinell, Robert F.↗

Theoretical performance of hydrogen-bromine rechargeable SPE fuel cell

A mathematical model was formulated to describe the performance of a hydrogen-bromine fuel cell. Porous electrode theory was applied to the carbon felt flow-by electrode and was coupled to theory describing the solid polymer electrolyte (SPE) system. Parametric studies using the numerical solution to this model were performed to determine the effect of kinetic, mass transfer, and design parameters on the performance of the fuel cell. The results indicate that the cell performance is most sensitive to the transport properties of the SPE membrane. The model was also shown to be a useful tool for scale-up studies.

Savinell, R. F.↗

Oxidatively stable microlayers of gas diffusion layers

The present invention is a microlayer for use with an electrically conductive porous substrate of a gas diffusion layer. The microlayer includes carbon particles and a polymeric composition of first highly-fluorinated polymers that are non-melt processable and second highly-fluorinated polymers that are melt processable.

Frisk, Joseph W.↗

Ultra-thin and strong formvar-based membranes with controlled porosity for micro- and nano-scale systems

Here, we present a methodology for developing ultra-thin and strong formvar-based membranes with controlled morphologies. Formvar is a thin hydrophilic and oleophilic polymer inert to most chemicals and resistant to radiation. The formvar-based membranes are viable materials as support structures in micro- and macro-scale systems depending on thinness and porosity control. Tunable sub-micron thick porous membranes with 20%–65% porosity were synthesized by controlling the ratios of formvar, glycerol, and chloroform. This synthesis process does not require complex separation or handling methods and allows for the production of strong, thin, and porous formvar-based membranes. An expansive array of these membrane characterizations including chemical compatibility, mechanical responses, wettability, as well as the mathematical simulations as a function of porosity has been presented. The wide range of chemical compatibility allows for membrane applications in various environments, where other polymers would not be suitable. Our formvar-based membranes were found to have an elastic modulus of 7.8 GPa, a surface free energy of 50 mN m -1 and an average thickness of 125 nm. Stochastic model simulations indicate that formvar with the porosity of ~50% is the optimal membrane formulation, allowing the most material transfer across the membrane while also withstanding the highest simulated pressure loadings before tearing. Development of novel, resilient and versatile membranes with controlled porosity offers a wide range of exciting applications in the fields of nanoscience, microfluidics, and MEMS.

36 MATERIALS SCIENCE↗

Build Orientation Dependent Microstructure in Polymer Laser Sintering: Relationship to Part Performance and Evolution with Aging

Laser sintering (LS) is widely used to produce functional polymeric parts; however, the resulting parts are often limited by their porous structure, and performance of the part may be strongly anisotropic. Relating the structural features of parts to build process conditions or powder feedstock has been explored previously. In contrast, little is known regarding how the unique internal structures of LS parts evolve and relate to their performance later in their life cycle, for example, after use in a real-world operating environment. In this study, a tightly controlled LS build process and measurement campaign by standard X-ray computed tomography (XCT), supported by high-resolution synchrotron XCT, was used to benchmark the internal microstructure (e.g. porosity) as a function of four different build orientations in printed polyamide-12 (PA-12) parts. The initial performance of the parts after printing was characterized by tensile testing and dynamic mechanical analysis (DMA). Arrays of PA-12 parts in different build orientations were exposed to steam (under pressure) and air across multiple temperature and time points for the purposes of accelerated aging through oxidative and hydrolytic breakdown. Exposing parts to steam dramatically altered the internal microstructure and functional properties such as the glass transition temperature, tensile properties, and damping behavior. Notably, post-aging XCT revealed large microstructural changes after only 40 h of steam treatment relative to the as-printed specimens. Furthermore, pore reorganization and changes in crystallinity occurred regardless of whether the steam temperature was aggressive enough to induce a significant loss in mechanical properties. The build orientation dependence on the aging rate was minimal with the relative trend in performance persisting across most metrics among the different orientations even after aging.

36 MATERIALS SCIENCE↗

Ceramic Proppant Design for In-situ Microbially Enhanced Methane Recovery

This project designed a new type of multi-functional lightweight proppant. The proppant is utilized as the conventional lightweight proppant but also transports microorganisms to coalbed reservoirs. The proppant is coated with a polymer which protects the methanogenic microorganisms and serves as a time-release delivery for methane generation. To produce the multifunctional proppant, we assigned five tasks: 1) culturing methanogenic microbes from natural carbon sources; 2) identifying optimized growth and methanogenesis conditions for the microbial consortia; 3) synthesizing the lightweight ceramic proppant; 4) encapsulating the consortia and proppant; and 5) demonstrating lab scale simulated performance by monitoring in-situ methane generation and hydraulic conductivity. Task 1) To evaluate the feasibility of ex-situ cultivation, natural microbial populations were collected from various hydrocarbon-rich environments and locations characterized by natural methanogenesis. Different rank coals, complex hydrocarbon sources, hydrocarbon seeps, and natural biogenic environments were incorporated in the sampling. Three levels of screening allowed selection of microbial populations, favorable nutrient amendments, sources of the microbial community, and quantification of methane produced from various coal types. Incubation periods of up to 24 weeks were evaluated at 23°C. Headspace concentrations of CH 4 and CO 2 were analyzed by gas chromatography. After a two-week incubation period of the most promising microbes, generated headspace gas concentrations reached 873,400 ppm for methane and 176,370 ppm for carbon dioxide. Task 2) A central composite design (CCD) was used to explore a broad range of operational conditions, examine the effects of the important environmental factors, such as temperature, pH and salt concentration, and query a feasible region of operation to maximize methane production from coal. Coal biogasification was optimal for this consortium at an initial pH value of 5.5, at 30 °C, and at a NaCl concentration 3.7 mg/cm 3 (i.e., 145,165 ppm). Task 3) To create the lightweight ceramic proppant, the kaolinite and iron oxide (Fe 2 O 3 ) mixture were sintered under reducing atmosphere varying partial pressures of oxygen from 1.7×10 -13 atm to 1.8×10-11 atm. The Fe 2 O 3 reduces to FeO and reacts with kaolinite decomposed to mullite to form Fe 2 SiO 4 , FeSiO 3 , and FeAl 2 O 4 . As a result the proppant develops large pores (~100 µm), giving it a low bulk density (1.43 g/cm 3 ), and high porosity (45.2 vol%) at P_(O_2 )of 1.8×10 -11 atm. The proppant sintered at P_(O_2 )of 1.7×10 -13 atm is characterized by smaller pores (26 µm), higher density (1.72 g/cm3) and lower porosity (37.5 vol%). Crush resistance testing at 9,000 psi yields 6.8 wt% fine particles increasing to 17.7 wt% in porous samples. Acid solubility varies from 5.5 wt% loss increasing to 12.9 wt% in porous samples. Task 4 and 5) The microbial consortia obtained from the optimized condition and lightweight proppant were encapsulated by calcium-alginate polymer. The encapsulation system, including microbes and a proppant, was stored at 20°C and 36°C. The sample stored at 36°C generated 7.1×[10] 3 ppm of methane at 670 h, whereas the sample incubated at 20°C generated 1.1×[10] 3 ppm of methane. Benchtop lab-scale bioreactors were constructed and showed with real-time measurements that, as the microbes produced methane, the pH decreased, and hydrogen and carbon dioxide gases were consumed. A calcium ion-selective sensor revealed the release mechanism of the microbes from encapsulation. The calcium ions interconnecting the alginate monomers were disassociated by counter cations such as protons and potassium ions. The counter cations bound to the carboxyl group on the alginate monomer, which thus lost its ionic interactions with the calcium ions, resulting in decomposition of the hydrogel structure. Furthermore, the conductivity was increased to ~700 mD-ft from ~530 mD-ft once the encapsulated sample was applied to the coal pack. The particle size of coal was reduced when the encapsulated sample was added to the coal. The reduced coal size implied that the microbes would consume the hydrocarbon in coal.

01 COAL, LIGNITE, AND PEAT↗

Numerical modeling of two-phase behavior in the PEFC gas diffusion layer

A critical performance limitation in the polymer electrolye fuel cell (PEFC) is attributed to the mass transport loss originating from suboptimal liquid water transport and flooding phenomena. Liquid water can block the porous pathways in the fibrous gas diffusion layer (GDL) and the catalyst layer (CL), thus hindering oxygen transport from the flow field to the electrochemically actives sites in the catalyst layer. In this paper, the study of the two phase behavior and the durability implications due to the wetting characteristics in the carbon paper GDL are presented using a pore-scale modeling framework.

30 DIRECT ENERGY CONVERSION↗