Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PNEUMATICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Drive mechanism for the shuttle orbiter/external tank propellant disconnect

The Space Shuttle design required development of a large, 0.43-m (17-in.) nominal diameter separable disconnect for the liquid hydrogen and liquid oxygen propellant lines at the orbiter-to-external-tank interface. The disconnect must provide for shutoff of the propellant flow area by simultaneous action of two rotary flapper valves (orbiter and external tank) prior to disconnect separation. In the case of pneumatic system failure, the rotary flapper valves are closed automatically through mechanical interlocking linkage during disconnect separation. The mechanism must meet requirements while accommodating changes in bearing clearances and linkage geometry over a wide temperature range from ambient to 20.37 K (-423°F). The mechanical design of the separable disconnect, kinematics of the drive mechanism, and the analysis and test methods used to verify proper operation and qualification for the Space Shuttle dynamic environments are presented.

E. Thomas↗

Development of a window protection assembly for a shuttle experiment

A window environmental protection assembly developed for the shuttle infrared leeside temperature experiment is described. The assembly consists of a carbon phenolic composite window mount which contains two silicon windows, a fibrous environmental protection plug to protect the windows during launch operations and ascent heating, a release mechanism used to jettison the plug just prior to atmospheric entry, and two pin puller mechanisms which retain the plug. The plug is released from the window mount assemblies using pneumatic pin pullers and separation springs in the release mechanism. The assembly was designed and tested to withstand the severe mechanical and thermal environments which could be experienced at the top of the shuttle orbiter vertical stabilizer during the ascent, on-orbit, and entry periods of the shuttle trajectory.

Bradley, O. H., Jr.↗

A study of poultry processing plant noise control techniques

A number of techniques can be used to reduce noise in poultry processing plants. In general, covering the ceiling with a noise-absorbing medium is a practical first step. Once the reflected noise levels are abated, treatment of specific identifiable noise courses can take place. The development, flammability, and mechanical properties of acoustic panels to be vertically suspended from the ceiling are discussed as well as the covers need to comply with USDA cleanability requirements. The isolation of drive motors and pumps from large expansive areas, the muffling of pneumatic devices, and the insulation of ice chutes are methods of source quieting. Proper maintenance of machinery and vibration monitoring are also needed to reduce hearing damage risk and to improve worker productivity and employee/supervisor relations.

Wyvill, J. C.↗

Tire/wheel concept

A tire and wheel assembly is disclosed in which a low profile pneumatic tire (having sidewalls which deflect inwardly under load) and a wheel (having a rim featuring a narrow central channel and extended rim flanges) form the combination. The extended rim flanges support the tire sidewalls under static and dynamic loading conditions to produce a combination particularly suited to aircraft applications.

Harper, P. M., Sr.↗

Low cost solar aray project: Experimental process system development unit for producing semiconductor-grade silicon using the silane-to-silicon process

This phase consists of the engineering design, fabrication, assembly, operation, economic analysis, and process support R&D for an Experimental Process System Development Unit (EPSDU). The mechanical bid package was issued and the bid responses are under evaluation. Similarly, the electrical bid package was issued, however, responses are not yet due. The majority of all equipment is on order or has been received at the EPSDU site. The pyrolysis/consolidation process design package was issued. Preparation of process and instrumentation diagram for the free-space reactor was started. In the area of melting/consolidation, Kayex successfully melted chunk silicon and have produced silicon shot. The free-space reactor powder was successfully transported pneumatically from a storage bin to the auger feeder twenty-five feet up and was melted. The fluid-bed PDU has successfully operated at silane feed concentrations up to 21%. The writing of the operating manual has started. Overall, the design phase is nearing completion.

Source record↗

The state of the art of general aviation autopilots - Now and in the future

A study was performed under contract with NASA-Langley Research Center to document the state of the art of general aviation (GA) autopilots and provide information about the current status of GA autopilot technology. Results are based on findings obtained from general and product literature, as well as interviews with manufacturers, users and service centers. The autopilot systems are divided into three categories - wing leveler, automatic, and integrated flight control systems, and a listing of currently available autopilots and their available options is presented. Various autopilot components are discussed, such as the display, data entry devices, and computers; gyroscopes, altitude sensors, airspeed sensors and accelerometers are presented as the primary sensor types. Electromechanical servos, pneumatic and hydraulic actuators are compared in their ability to improve airframe response. Recommendations concerning potential areas of further research and possible areas of improvement are also presented.

Roskam, J.↗

Moving-Surface Follower Aids Microsurgery

Novel manipulator follows movements of arteries and muscles, enabling precise placement of probe or other microsurgical tool in moving tissue. Microprobe assembly is mounted on output of pneumatic servo of commercial noncontracting thickness gage. Pulsations of tissue surface to be penetrated by probe are sensed by gage and followed by servo, eliminating relative motion between tissue and probe.

Feldstein, C.↗

Steady generation of aerosols with an improved constant output atomizer

It is common practice to generate laboratory aerosols of soluble materials with pneumatic atomizers. In a typical device, a solution of the substance to be aerosolized is injected into a jet of air and the liquid is broken up into very small droplets. After forced evaporation, a dry aerosol of the solute is produced. A number of commercially available devices were tested, and despite differences in design, all the atomizers tested suffered from short- and/or long-term fluctuations of their output particle number concentrations. The mechanisms responsible for atomizer instabilities are discussed and methods for alleviating these problems are considered.

Dea, J. Y.↗

Aerosol generation and distribution system for the Third International Cloud Condensation Nuclei Workshop

In order to obtain identical samples participating CCN instruments and aerosol characterizing equipment were located along and connected to a 8.2 cm diameter aluminum tube through which the test aerosols were pumped directly from the source at very slight overpressure. Of the total of 29 experiments, 18 were carried out with artificial NaCl or (NH4)2SO4 aerosols. These were generated from salt solutions by pneumatic atomizers of special design to ensure high constancy of the aerosol output concentration. In three experiments with insoluble CCN (AgI, paraffin wax) the aerosols were generated thermally. In some of the tests, an electrostatic classifier was used for narrowing the particle size distributions.

Katz, U.↗

The design of a mechanical referencing system for the rear drum of the Longwall Shearer Coal Miner

The design of two systems which reference the position of a longwall shearer coal miner to the mine roof of the present cut and of the last cut are presented. This system is part of an automation system that will guide the rear cutting drum in such a manner that the total depth of cut remains constant even though the front drum may be following an undulating roof profile. The rear drum referencing mechanism continually monitors the distance from the mine roof to the floor for the present cut. This system provides a signal to control a constant depth of cut. The last cut follower mechanism continually monitors the distance from the mine roof of the prior cut to the cutting drum. This latter system provides a signal to minimize the step height in the roof between cuts. The dynamic response of this hydraulic-pneumatic and mechanical system is analyzed to determine accumulator size and precharge pressure.

Jones, E. W.↗

Planar equations of rollout motion for an aircraft with free or steerable landing gears

Equations were derived for an aircraft in a three-point attitude. Transient tire forces were simulated by delaying the application of forces derived from steady-state considerations. Predicted rollout trajectories were similar to those measured in tests of a small-scale landing-gear model equipped with pneumatic tires (where a laterally sloping runway was used to simulate a crosswind), both with and without nose-wheel steering.

Sleeper, R. K.↗

System for slicing wafers

A newly patented process for slicing silicon wafers that has distinct advantages over methods now widely used is described. The primary advantage of the new system is that it allows the efficient slicing of a number of ingots simultaneously at high speed. The cutting action is performed mechanically, most often with diamond particles that are transported to the cutting zone by a fluid vehicle or have been made an integral part of the blade by plating or impregnation. The new system uses a multiple or ganged band saw, arranged and spaced so that each side, or length, segment of a blade element, or loop, provides a cutting function. Each blade is maintained precisely in position by guides as it enters and leaves each ingot. The cutting action is performed with a conventional abrasive slurry composed of diamond grit suspended in an oil- or water-based vehicle. The distribution system draws the slurry from the supply reservoir and pumps it to the injection tubes to supply it to each side of each ingot. A flush system is provided at the outer end of the work-station zone. In order to reduce potential damage, a pneumatically driven flushing fluid is provided.

Source record↗

Static investigation of the circulation control wing/upper surface blowing concept applied to the quiet short haul research aircraft

Full scale static investigations were conducted on the Quiet Short Haul Research Aircraft (QSRA) to determine the thrust deflecting capabilities of the circulation control wing/upper surface blowing (CCW/USB) concept. This scheme, which combines favorable characteristics of both the A-6/CCW and QSRA, employs the flow entrainment properties of CCW to pneumatically deflect engine thrust in lieu of the mechanical USB flap system. Results show that the no moving parts blown system produced static thrust deflections in the range of 40 deg to 97 deg (depending on thrust level) with a CCW pressure of 208,900 Pa (30.3 psig). In addition, the ability to vary horizontal forces from thrust to drag while maintaining a constant vertical (or lift) value was demonstrated by varying the blowing pressure. The versatility of the CCW/USB system, if applied to a STOL aircraft, was confirmed, where rapid conversion from a high drag approach mode to a thrust recovering waveoff or takeoff configuration could be achieved by nearly instantaneous blowing pressure variation.

Eppel, J. C.↗

Decoupler pylon: wing/store flutter suppressor

A device for suspending a store from a support such as an aircraft wing and more specifically for increasing the flutter speed of an aircraft flying with attached store and reducing the sensitivity of flutter to changes in the pitch inertia and center of gravity location of the store is described. It comprises softspring where the store pitch mode is decoupled from support modes and a low frequency active control mechanism which maintains store alignment. A pneumatic suspension system both isolates the store in pitch and, under conditions of changing mean load, aligns the store with the wing to which it is attached.

Reed, W. H., III↗

Rotor systems research aircraft /RSRA/ rotor force and moment measurement system

The two Rotor Systems Research Aircraft (RSRA) are flight vehicles with unique measurement capabilities. The primary goal of the RSRA is direct measurement of rotor forces and moments in flight. This is accomplished through a rotor force and moment measurement system comprised of load cells and/or hydro-pneumatic isolator units which are integral to the aircraft structure. Due to structural flexibility, the aircraft must undergo a physical calibration. A static calibration of the first RSRA has been completed, and data analysis has progressed through determination of a linear calibration algorithm. Design, development, and operation of the RSRA rotor force and moment measurement system and the Static Calibration Facility are described, and results of the calibration are presented.

Burks, J. S.↗

Experimental stress analysis of a thin-walled pressurized torus loaded by contact with a plane

It is pointed out that pneumatic tires have a large effect on the overall landing characteristics of an aircraft. The dynamic response upon landing and steering are crucial to the safety of the vehicle and the occupants. The present investigation has the objective to compare experimentally determined strains on an inner tube in contact with a flat plate with numerical values obtained on the basis of a finite element prediction, taking into account an employment of the Structural Analysis of General Shells (STAGS). The obtained results suggest that the clamped boundary condition utilized in the STAGS calculation is not exactly simulated by the employed test setup.

Hill, D. E.↗

Holding Tubes in Place for Brazing

Simple method prevents loosening due to thermal mismatch. Four segment die pushed outward against tubing wall by tapered ram. Boss on each segment of die produces dimple in wall. Ram driven by commercial pneumatic cylinder powered by air at 250 psi. Method applicable to brazing of heat exchanges, thrust chambers, and other assemblies in which thermal expansion coefficients of materials differ significantly.

Ambrisco, D.↗

Electronically-Scanned Pressure Sensors

Sensors not pneumatically switched. Electronic pressure-transducer scanning system constructed in modular form. Pressure transducer modules and analog to digital converter module small enough to fit within cavities of average-sized wind-tunnel models. All switching done electronically. Temperature controlled environment maintained within sensor modules so accuracy maintained while ambient temperature varies.

Coe, C. F.↗