Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Optical Microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2015

Analysis of integrity and microstructure of linear friction welded Waspaloy

Nickel-base superalloy, Waspaloy, was linear friction welded (LFWed) under different axial shortening conditions of 2.0, 3.4, and 4.6 mm. The tensile properties and microhardness of the weldments were investigated in the as-LFWed condition and compared with those in the post-weld heat treated (PWHTed) condition. Mechanical properties were related to microstructures following examination by optical microscopy, high resolution scanning electron microscopy, and electron backscatter diffraction (EBSD). Analyses of the EBSD results in terms of the misorientation angle distribution, which represents the stored energy, were performed. In the as-LFWed condition, the yield strength (YS) and ultimate tensile strength (UTS) increased with axial shortening due to greater expulsion of the softened interfacial material toward the periphery as flash. In contrast, with increasing axial shortening the total elongation initially remained constant and then decreased. This was also related to the expulsion of the softened interfacial material into the bifurcated flash. Extensive dissolution of the strengthening phase (γ′) in the weld area during linear friction welding (LFW) contributed to the lower YS and UTS in the as-welded condition compared to the PWHTed condition where the γ′ particles were recovered. After performing post-weld heat treatment (PWHT), the total elongation improved due to the relaxation of stored energy and grain growth in the thermomechanically affected zone (TMAZ). - Highlights: • Tensile property and microstructure in Waspaloy linear friction welds were studied. • Yield strength and ultimate tensile strength increased with axial shortening. • Elongation initially remained constant and then decreased with axial shortening. • Post-weld heat treat recovered dissolved γ′ particles and increased weld strength. • Stored energy relaxation during post-weld heat treatment improved weld elongation.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Evolution of microstructure, texture and inhibitor along the processing route for grain-oriented electrical steels using strip casting

In the present work, a regular grade GO sheet was produced successively by strip casting, hot rolling, normalizing annealing, two-stage cold rolling with intermediate annealing, primary recrystallization annealing, secondary recrystallization annealing and purification. The aim of this paper was to characterize the evolution of microstructure, texture and inhibitor along the new processing route by comprehensive utilization of optical microscopy, X-ray diffraction and transmission electron microscopy. It was found that a fine microstructure with the ferrite grain size range of 7–12 μm could be obtained in the primary recrystallization annealed sheet though a very coarse microstructure was produced in the initial as-cast strip. The main finding was that the “texture memory” effect on Goss texture started on the through-thickness intermediate annealed strip after first cold rolling, which was not similar to the “texture memory” effect on Goss texture starting on the surface layers of the hot rolled strip in the conventional production route. As a result, the origin of Goss nuclei capable of secondary recrystallization lied in the grains already presented in Goss orientation in the intermediate annealed strip after first cold rolling. Another finding was that fine and dispersive inhibitors (mainly AlN) were easy to be produced in the primary recrystallization microstructure due to the initial rapid solidification during strip casting and the subsequent rapid cooling, and the very high temperature reheating usually used before hot rolling in the conventional production route could be avoided. - Highlights: • A regular grade grain-oriented electrical steel was produced. • Evolution of microstructure, texture and inhibitor was characterized. • Origin of Goss nuclei lied in the intermediate annealed strip. • A fine primary recrystallization microstructure could be produced. • Effective inhibitors were easy to be obtained in the new processing route.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Strain induced grain boundary migration effects on grain growth of an austenitic stainless steel during static and metadynamic recrystallization

Static and metadynamic recrystallization of an AISI 304L austenitic stainless steel was investigated at 1100 °C and 10{sup −} {sup 2} s{sup −} {sup 1} strain rate. The kinetics of recrystallization was determined through double hit compression tests. Two strain levels were selected for the first compression hit: ε{sub f} = 0.15 for static recrystallization (SRX) and 0.25 for metadynamic recrystallization (MDRX). Both the as-deformed and the recrystallized microstructures were investigated through optical microscopy and electron back-scattered diffraction (EBSD) technique. During deformation, strain induced grain boundary migration appeared to be significant, producing a square-like grain boundary structure aligned along the directions of the maximum shear stresses in compression. EBSD analysis revealed to be as a fundamental technique that the dislocation density was distributed heterogeneously in the deformed grains. Grain growth driven by surface energy reduction was also investigated, finding that it was too slow to explain the experimental data. Based on microstructural results, it was concluded that saturation of the nucleation sites occurred in the first stages of recrystallization, while grain growth driven by strain induced grain boundary migration (SIGBM) dominated the subsequent stages. - Highlights: • Recrystallization behavior of a stainless steel was investigated at 1100 °C. • EBSD revealed that the dislocation density distribution was heterogeneous during deformation. • Saturation of nucleation sites occurred in the first stages of recrystallization. • Strain induced grain boundary migration (SIGBM) effects were significant. • Grain growth driven by SIGBM dominated the subsequent stages.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Oxidation behaviors of porous Haynes 214 alloy at high temperatures

The oxidation behaviors of porous Haynes 214 alloy at temperatures from 850 to 1000 °C were investigated. The porous alloys before and after the oxidation were examined by optical microscopy, scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) analyses, and X-ray photoelectron spectroscopy (XPS). The oxidation kinetics of the porous alloy approximately follows a parabolic rate law and exhibits two stages controlled by different oxidation courses. Complex oxide scales composed of Cr{sub 2}O{sub 3}, NiCr{sub 2}O{sub 4} and Al{sub 2}O{sub 3} are formed on the oxidized porous alloys, and the formation of Cr{sub 2}O{sub 3} on its outer layer is promoted with the oxidation proceeding. The rough surface as well as the micropores in the microstructures of the porous alloy caused by the manufacturing process provides fast diffusion paths for oxygen so as to affect the formation of the oxide layers. Both the maximum pore size and the permeability of the porous alloys decrease with the increase of oxidation temperature and exposure time, which may limit its applications. - Highlights: • Two-stage oxidation kinetics controlled by different oxidation courses is showed. • Oxide scale mainly consists of Cr{sub 2}O{sub 3}, NiCr{sub 2}O{sub 4} and Al{sub 2}O{sub 3}. • Rough surface and micropores lead to the formation of uneven oxide structure. • Content of Cr{sub 2}O{sub 3} in the outer layer of the scale increases with time at 1000 °C. • Maximum pore size and permeability decrease with increasing temperature and time.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Structure and tribological properties of steel after non-vacuum electron beam cladding of Ti, Mo and graphite powders

The non-vacuum electron beam cladding technique was used to fabricate layers alloyed with Ti, Mo and C on the surface of low-alloyed steel. Two types of experiments were carried out. In the first experiment, a mixture of Ti and graphite powders was used for cladding; in the second, a mixture of Ti, Mo and graphite powders was used for cladding. CaF{sub 2} powder or a mixture of CaF{sub 2} and LiF powders was used as flux. The thickness of the cladded layers was in the range of 2–2.2 mm. The structure of the layers was studied using optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The microhardness after cladding of the layers fabricated by cladding of Ti and graphite powders was 8–9 GPa, while the microhardness of layers with Mo additions reached 11–12 GPa. The highest wear resistance at sliding friction and friction in abrasive environment was reached in the samples fabricated using Ti, Mo and graphite mixture due to the higher hardness and the martensite–austenite structure of the matrix. The wear resistance against fixed abrasive particles was 2.4 times higher compared to that of carburized and quenched steel. - Highlights: • Ti, C and Mo mixture of powders was cladded using non-vacuum electron beam treatment. • The depth of the cladded layers was 2.0 … 2.2 mm. • The microhardness of layer with Mo, Ti and C additions reached ~ 11 … 12 GPa. • The hardening of the layers caused by the formation of TiC particles and martensitic matrix • Wear resistance of cladded coatings was 2.4 higher than carburized steel.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Effect of Zn on microstructure, texture and mechanical properties of Al-Mg-Si-Cu alloys with a medium number of Fe-rich phase particles

Highlights: • Zn has a negligible influence on the final recrystallization microstructure and texture of Al-Mg-Si-Cu alloys. • By adding Fe-rich phase particles to refine the recrystallization grain sizes could control the texture. • The deep drawability of Al-Mg-Si-Cu alloys could be affected by solute Zn atom besides the microstructure and texture. - Abstract: The effect of Zn on the microstructure, texture evolution and mechanical properties of Al-Mg-Si-Cu alloys with a medium number of Fe-rich phase particles was investigated using tensile testing machine, optical microscopy (OM), scanning electron microscope (SEM), transmission electron microscope (TEM) and X-ray diffractometer (XRD) in the present study. The results show that Zn addition has a significant influence on the final mechanical properties, but a slight effect on microstructure and final recrystallization texture. Zn addition is favorable to increase yield strength, ultimate tensile strength and elongation, however it is detrimental to improve r value and reduce Δr value. During the thermomechanical processing, the microstructure almost has nothing to do with Zn addition. However, Zn could prevent the secondary phase particles from precipitating during intermediate annealing. In contrast to the alloy sheet without Zn, the alloy sheet with 1.0 wt% Zn always has weaker textures before final cold rolling, but a stronger texture after experiencing final cold rolling. After solution treatment, they almost possess the same recrystallization texture. Finally, the effect of Zn addition on the recrystallization texture was discussed. Their similar recrystallization texture can be attributed to the similar microstructure, which was caused by the medium number of Fe-rich phase particles.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of gadolinium addition on microstructural evolution and solidification characteristics of Al-15%Mg2Si in-situ composite

Highlights: • The Al{sub 3}Gd is the heterogeneous nucleation of primary Mg{sub 2}Si in Al-15%Mg{sub 2}Si composite. • Addition of Gd to Al-15%Mg{sub 2}Si resulted in the formation of Al{sub 2}Si{sub 2}Gd and AlSiGd intermetallic compounds. • Absorption of Gd atoms preferentially on {100} facets of Mg{sub 2}Si crystals changed its growth manners. • Primary Mg{sub 2}Si transformed from coarse-dendritic to perfect truncated octahedral shape after treating with 1.0 wt% Gd. • Gd addition increased the nucleation and growth temperatures of primary Mg{sub 2}Si. - Abstract: The current study investigated the effects of gadolinium (Gd) addition (0, 0.3, 0.5, 1.0, and 2.0 wt%) on microstructural development and solidification characteristics of hypereutectic Al-15%Mg{sub 2}Si in-situ composite. Microstructural examinations were carried out via optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), and electron backscattered diffraction (EBSD). The results showed that an addition of 1.0 wt% Gd, changed the morphology of primary Mg{sub 2}Si from coarse dendritic to fine truncated octahedral shape. Furthermore, the average size of primary Mg{sub 2}Si particles decreased from 40 μm to 20 μm and density increased from 495 to 1167 particles/mm{sup 2}. Besides that, cooling curve thermal analysis (CCTA) technique revealed that Gd addition increased nucleation and growth temperatures of primary Mg{sub 2}Si phase. It is proposed that modification and refinement mechanism of Gd addition are mainly attributed to formation of tiny Al{sub 3}Gd particles as the heterogeneous nucleation substrates for primary Mg{sub 2}Si, which results in a refined distribution of these particles and poisoning effect by adsorbing Gd atoms, preferentially on {100} facets of Mg{sub 2}Si crystals. Moreover, it is believed that formation of Gd intermetallic compounds is responsible for refinement of primary Mg{sub 2}Si particles.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Microstructure evolution and mechanical characterization of Nd:YAG laser beam welded titanium tubes

Highlights: • Joining of thin titanium tubes using laser beam welding. • Fusion zone exhibited coarse granular like grains with serrated and irregular boundaries. • Large spherical and irregular shape pores were observed at lower welding speeds. • Misorientation angle distribution indicated substructure boundaries along with single β grain formation from double α grains. • Fusion zone strengthened by substructure boundaries, solid solution strengthening and dislocation density. - Abstract: Grade 2 titanium tubes of outer diameter 60 mm and wall thickness 3.9 mm were effectively joined by Nd:YAG laser. The welding speed was varied in five levels (2.50, 2.75, 3.00, 3.25 and 3.50 m/min). The microstructure evolution was studied using optical microscopy and advanced characterization techniques. The bead geometry changed from parallel shape to wedge shape with increased welding speed due to changes in surface tension. The macrographs showed three zones namely fusion zone, heat affected zone (HAZ) and base metal. Coarse granular structure with irregular and serrated contours was observed in the fusion zone. Acicular α grains were observed at the extreme outer edge of the fusion zone due to rapid cooling. Spherical and irregular shaped pores were observed near the centerline of the fusion zone at lower welding speeds due to large amount of entrapped gases and downward sweeping solidification front. The grain size decreased with increased welding speed due to higher cooling rate. The misorientation angle distribution map showed three distinct regions. The increase in welding speed caused an increase in low angle boundaries and a reduction in very high angle boundaries. High density of dislocations was observed in the fusion zone due to thermal stresses caused by solidification. The microhardness of the fusion zone was recorded to be higher than base metal due to substructure boundaries, solute elements and dislocations. The increase in welding speed shifted the fracture location from fusion zone to base metal and fracture mode from brittle to ductile.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Pre-processing related recrystallization behavior in β annealing of a near-β Ti-5Al-5Mo-5V-3Cr-1Zr titanium alloy

Highlights: • Recrystallization behavior of Ti-55531 alloy in β annealing under four typical pre-processing conditions is studied. • Recrystallization nucleation mode is governed by the size and distribution of substructures. • The sequence of phase transformation and β recrystallization significantly affects recrystallized grain size. • The uniform substructures produce a higher fraction of low angle grain boundaries after full recrystallization. - Abstract: Recrystallization behavior of Ti-55531 alloy in β annealing is explored for grain refinement during primary hot working. Four typical pre-processing conditions were adopted to characterize the diverse processing routes of primary hot working: deformation and annealing in the two-phase region, deformation of globularized structure in two-phase region, deformation of lamellar structure in two-phase region and deformation in single β region. The microstructure evolution in β annealing was quantified by Optical Microscopy (OM), Electron Backscattered Diffraction (EBSD), X-ray diffraction (XRD) and quantitative metallography. The results indicate that the nucleation mode of static recrystallization is determined by the size and distribution of substructures prior to annealing which is related to pre-processing route. The uniform substructures in as-deformed globularized structure produce a higher fraction of low angle grain boundaries after full recrystallization. Fine β recrystallized structure can be obtained when β recrystallization is accompanied by α-to-β phase transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2018

EBSD characterization of the eutectic microstructure in hypoeutectic Fe-C and Fe-C-Si alloys

Highlights: • EBSD investigation of eutectic cementite and austenite in as-solidified low-alloy cast iron • Crystallographically independent growth of rapidly solidified cementite/austenite eutectic • Epitaxial growth of eutectic austenite from primary dendrites • Eutectic cementite and eutectoid ferrite frequently obey Bagaryatsky or Pitsch-Petch orientation relationship. - Abstract: Hypoeutectic Fe-C and Fe-C-Si model alloys were produced at different solidification conditions. Copper mold casting yields low cooling rates promoting the formation of a eutectic microstructure, which is characterized by two morphologies: elongated cementite plates and a rod structure growing perpendicular to the plates, i.e. austenite rods in a cementite matrix. Electron beam surface remelting generates a mainly plate-like eutectic due to rapid solidification. The microstructures were characterized by light-optical microscopy and electron backscatter diffraction (EBSD). The latter allows for a spatially resolved investigation of the growth crystallography of the eutectic phases. Thereby, a possible existence of crystallographic orientations relationships between cementite and austenite within the plate-like eutectic was assessed experimentally. The eutectic phases were found to grow largely crystallographically independently. Moreover, ferrite and eutectic cementite within the decomposed eutectic microstructure frequently comply with the Bagaryatsky or the Pitsch-Petch orientation relationship. Complementary X-ray diffraction (XRD) analysis reveals a pronounced cementite {002} texture in the microstructure produced by mold casting. Characteristic changes in the lattice parameters indicate that as-cast cementite is non-stoichiometric.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Enhancing the tensile properties of EBM as-built thin parts: Effect of HIP and chemical etching

Highlights: • The EBM process leads to important cross section variations in thin parts. • Stress calculation must be based on the average section in order to be relevant. • As-built state has a detrimental effect on every mechanical property. • Mechanical properties of machined samples are met with chemical etching. • HIP has a beneficial effect on the ductility. - Abstract: As-built Ti-6Al-4 V thin parts were manufactured using Electron Beam Melting (EBM) and characterized by optical microscopy and laboratory X-ray tomography in order to observe their microstructure, pore distribution and surface aspect. Chemical etching and HIP post-treatments were applied to as-built samples and their effect on the material and static mechanical properties were studied. Tensile tests were performed on both as-built and post-treated samples and their results compared to the ones reported in the literature for machined EBM samples. Because of the significant variations of the cross section observed along the gauge length, the calculation of the tensile stresses is not straightforward. Three simple sections were measured from the tomography scans. The average section along the gauge length was considered as the most suitable. The tensile mechanical properties of the as-built samples were studied and a detrimental effect of the surface state on the yield strength, ultimate tensile strength and elongation to failure was observed. Smoothing of the surface irregularities induced by chemical etching provoked an increase of those mechanical properties whereas the change of the microstructure generated by the HIP treatment leads to a decrease of the material strength that goes along with an increase of the ductility. Down scaling factors were proposed in order to take into account the sample state, as-built or post-treated.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Evaluation of the microstructure and mechanical properties of WC particle reinforced aluminum matrix composites fabricated by friction stir processing

Highlights: • FSP was used for the preparation of aluminum matrix composites reinforced with WC particle. • WC particles were uniformly distributed in the composite. • WC particles refined the grains of aluminum matrix. • WC particles enhanced the hardness and tensile strength, but decreased the ductility. - Abstract: Tungsten carbide (WC) is an attractive reinforcing material for aluminum and its alloys. However, it is technically challenging to fabricate WC particle reinforced aluminum matrix composites (AMCs) with homogeneous distribution of WC particles by liquid state processing techniques because of large density gradient. The present work aim to produce WC particle reinforced aluminum matrix composites (AMCs) through friction stir processing (FSP) and analyze the effect of its volume fraction on the microstructural features and the mechanical behavior of the developed AMCs. Microstructural evaluation was conducted on the cross-sections of the samples by optical microscopy (OM), scanning electron microscopy (SEM) and electron backscattered diffraction (EBSD). Microhardness testing was conducted across the cross-sections of FSPed samples to obtain hardness profiles and tensile test was conducted on as-received Al and FSPed samples. The fabricated AMCs exhibited the homogeneous distribution of WC particle with no obvious particle clustering in the stir zone, irrespective of position and WC particle volume fraction. Excellent WC/Al interfacial bonding was obtained in all FSPed AMCs with obviously refined grains. The average size of WC particles after FSP was slightly reduced with the increased volume fraction. It was also found that increasing the volume fraction of WC particles favored the grain refinement, improved the hardness and strength, but decreased the ductility. This improvement in the hardness and strength was attributed to the grain refinement strengthening and homogeneous distribution of WC particles. The decreased ductility resulted from the introduction of more WC particles. Increasing the volume fraction of WC particles caused the nature of fracture to move towards brittle nature.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Pulsed laser powder bed fusion additive manufacturing of A356

Highlights: • Dense A356 specimens (98 ± 0.4%) were fabricated using a customized P-LPBF system. • Microstructure and grain morphology were examined using LOM, SEM, and EBSD. • Solidification front velocities (R) were evaluated through the KGT model. • A columnar grain structure was observed and predicted by the Hunt's criterion. - Abstract: A356 (Al7SiMg) specimens were fabricated through pulsed laser powder bed fusion (P-LPBF) additive manufacturing. Microstructural examinations and analyses were carried out through the usage of light optical microscopy (LOM), scanning electron microscopy (SEM), and electron backscatter diffraction (EBSD). The results revealed a fine cellular microstructure with the intercellular network consisting of Al cells and defined by a network of Si arms. The Al cells at the center of the melt pools and within the melt pool boundary bands were measured to be 423 ± 49 nm and 664 ± 76 nm, respectively. The presence of a fine columnar grain structure and epitaxial growth on partially melted grains was observed and explained by the KGT model and Hunt's criterion.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of cooling conditions on microstructure and mechanical properties of friction stir welded 7055 aluminium alloy joints

Highlights: • Water cooling improves tensile properties of friction stir welded 7055 Al alloy. • Water cooling results in smaller grains and second phase in nugget zone. • Water cooling results in finer second phase in thermos-mechanically affected zone. • Water cooling results in finer second phase in heat affected zone. • Fracture surface is flat for air-cooled joint but zig-zag for water-cooled one. - Abstract: The microstructure and mechanical properties of friction stir welded 7055 aluminium alloy under air cooling and water cooling were investigated by means of hardness and tensile testing, optical microscopy and transmission electron microscopy. Water cooling results in reduced softening in the weld zone and therefore higher tensile strength compared to air cooling. Fracture generally occurs within the thermo-mechanically affected zone (TMAZ) and heat affected zone (HAZ) on the retreating side in joints welded under air cooling but shifts towards the TMAZ and nugget zone (NZ) in the joints welded under water cooling. The fracture surfaces are generally flat for the air-cooled joint, but exhibits a zig-zag feature for the water-cooled joint. The mechanical behaviour of the weld has been discussed in light of the change in grain structure and precipitation in the NZ, TMAZ and HAZ caused by cooling conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Influence of rapid heating and cooling combined with deformation at ultrahigh strain rates on the microstructure evolution of pure titanium shaped charge liner

Highlights: • A slug prepared from pure titanium SCL was recovered after detonation deformation at an ultrahigh strain rate over 10{sup 5} s{sup −1}. • The α → β → α phase transformation occurred in Ti SCL during the ultrahigh-strain -rate deformation. • The microstructures of the recovered slug included lamellar α grains, equiaxed α grains, and jagged α grains. - Abstract: A slug prepared from pure titanium shaped charge liners was recovered after detonation deformation at an ultrahigh strain rate over 10{sup 5} s{sup −1} and high strain over 500%. Optical microscopy, electron backscattered diffraction (EBSD), and transmission electron microscopy (TEM) were employed to investigate the microstructure of the Ti shaped charged liner before and after the detonation deformation. The microstructures of the recovered slug include lamellar α grains, equiaxed α grains within localized shear bands, and jagged α grains. EBSD results indicated that the grain orientation distribution is random and no texture was observed in the slug. TEM observation revealed that the α → β → α phase transformation occurred owing to the rapid heating and cooling combined with deformation at ultrahigh strain rates in the Ti shaped charge liner. No melting phenomenon was observed during the deformation process. The deformation process consisted of the explosive detonation stage combined with rapid heating and the subsequent penetration stage combined with rapid cooling. In the explosive detonation stage, the α → β phase transformation instantaneously occurred via a martensitic mechanism. In the penetration stage, the high-temperature slug in β state was cooled rapidly and showed different deformation behaviors in three different areas.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and mechanical properties development of micro channel tubes in extrusion, rolling and brazing

Highlights: • Rolling and brazing greatly affect the properties of micro-channel tubes (MCTs). • The properties of MCTs are investigated by the evolution of the microstructure. • Strength is decreased by 47% at 5%-rolling reduction ratio and 3-minute brazing. • Ductile fracture mode is observed by OM at failure of MCTs under inner pressure. - Abstract: In addition to extrusion, the post-processing of rolling and brazing has significant effect on the mechanical properties of multi-port tubes. The aluminum micro channel tubes, especially the seam welding zone in the internal webs, are investigated in terms of mechanical tests, microstructure characterization, and finite element analysis. The effect of the post-process of rolling are quantified by varying amount of rolling reduction ratios. Tensile strength and pressure bearing capacity are determined by tensile tests and burst pressure tests, respectively. The evolution of the microstructure within the seam wielding zone is characterized by Electron backscattered diffraction (EBSD) and optical microscopy (OM). The fracture profile observed by OM indicates ductile fracture mode. The pressure bearing capacity is reduced by ~47% at 5% reduction ratio of rolling followed by 3-minute brazing, where largest grains are obtained due to abnormal grain growth.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Hydrogen induced cracking susceptibility of API 5L X70 pipeline steel in relation to microstructure and crystallographic texture developed after different thermomechanical treatments

Highlights: • crack propagated mainly along deformed-banded microstructure. • Lower failure strength manifested at pipeline steel surface compared to the mid-thickness. • Greater fraction of martensite/austenite constituents featured in specimen WG relative to specimen WH. • Early onset of cracking in specimen WH showed no preference to specific crystallographic orientation. • Multi-component inclusion particle was revealed along crack propagation path. - Abstract: Thermomechanical treatments offer an innovative means of controlling microstructure development and improving resistance to hydrogen induced cracking (HIC) in pipeline steel. This study was conducted on two X70 pipeline steels (labelled WG and WH) of the same chemical composition, but processed with different thermomechanical parameters. Specimen WG was hot rolled at a higher temperature range of 880–820 {sup °}C, while specimen WH was hot rolled between 830 and 760 {sup °}C before cooling at a rate of 25 {sup °}C/s. Early onset of HIC was observed in specimen WH after electrochemical hydrogen charging for 12 h in a solution of 0.2 M H{sub 2}SO{sub 4} and 3 g/l NH{sub 4}SCN, without any applied stress. Also, test pieces from the surface and mid-thickness layers of each pipeline steel were subjected to slow strain rate tensile (SSRT) test with in-situ hydrogen charging. Characterization techniques such as Optical Microscopy, Scanning Electron Microscopy, Electron Backscattered Diffraction and X-ray Diffraction were used to investigate the structure pipeline steel specimens. The role of inclusions on HIC was studied by Energy Dispersive X-ray Spectroscopy. Although the microstructure of both specimens were predominantly ferritic, more martensite/retained austenite (M/A) constituents featured in WG. Further crystallographic texture analysis indicates that grain orientation at the surfaces of both test specimens were similar with deviations towards <111> on the inverse pole figure (IPF); whereas, pole intensity at the mid-thickness deviated towards the <001> direction. Considering the increased fraction of banded-deformed grains with high stored energy, the lower HIC resistance of specimen WH in comparison to specimen WG was justified.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Characterization of high-temperature mechanical properties of plasma-cladded coatings with thermo-mechanical coupling

High temperature mechanical properties was detected here to study the failure and strengthening mechanism of the coating-substrate (cobalt-based coatings were fabricated on FV520B substrate) integral structure with thermo-mechanical coupling effects. Microstructure, phase composition, element distribution of the coatings was characterized by optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscope (TEM), electron back scattering diffraction (EBSD), X-ray diffraction (XRD), electron probe microanalysis (EPMA) and energy dispersive X-ray analysis (EDS). Results elucidate that fracture occurs in the coating for Co50 coating-substrate structure from 300 °C to 700 °C, but failure position transfer to substrate from coating at elevated temperatures with the addition of niobium and cerium oxide. Throughout, there is no crack originated from the interface. Fracture mechanism: the dislocation pile-up causes great stress concentration in the grain boundary, which results in the nucleation of the crack, and then the crack extends along the hard brittle Fe-Cr phase until the material fails. HRTEM shows the high density dislocation and the severe lattice distortion was formed during tensile deformation. On the macro level, the fracture tends to occur in the coarse dendrites region.

36 MATERIALS SCIENCE↗