Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “OLIVINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Studies of Mineral Properties at Mantle Condition using Deformation Multi-Anvil Apparatus

This paper reports recent studies of the rheological and viscoelastic properties of minerals at mantle pressure and temperature using Deformation multi-anvil apparatus (D-DIA). Stress-strain-time relations were measured using synchrotron X-ray radiation to determine these properties. Rheological properties of San Carlos olivine were measured at pressure up to 10 GPa and indicated that the effect of pressure on the viscosity of olivine is much smaller than previous reported. The unique capability of synchrotron X-ray can resolve the stress heterogeneity within a polycrystalline material as well as within a multi-phase mixture and elucidate the stress-strain distribution in an aggregate. Anelasticity measurements were carried out using olivine as the sample at mantle pressure and temperatures. The results showed that grain boundary activity rather than pressure dominate the relaxation processes. The aim of this paper is to illustrate the methods using new tools for high pressure research.

58 GEOSCIENCES↗

Fluidized bed gasification of waste-derived fuels

Five alternative waste-derived fuels obtained from municipal solid waste and different post-consumer packaging were fed in a pilot-scale bubbling fluidized bed gasifier, having a maximum feeding capacity of 100 kg/h. The experimental runs utilized beds of natural olivine, quartz sand or dolomite, fluidized by air, and were carried out under various values of equivalence ratio. The process resulted technically feasible with all the materials tested. The olivine, a neo-silicate of Fe and Mg with an olive-green colour, has proven to be a good candidate to act as a bed catalyst for tar removal during gasification of polyolefin plastic wastes. Thanks to its catalytic activity it is possible to obtain very high fractions of hydrogen in the syngas (between 20% and 30%), even using air as the gasifying agent, i.e. in the most favourable economical conditions and with the simplest plant and reactor configuration. The catalytic activity of olivine was instead reduced or completely inhibited when waste-derived fuels from municipal solid wastes and aggregates of different post-consumer plastic packagings were fed. Anyhow, these materials have given acceptable performance, yielding a syngas of sufficient quality for energy applications after an adequate downstream cleaning.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Ni and Co Incorporation in Forsterite: A Density Functional Theory Study with Hubbard Correction

Ni and Co are critical elements for the world economy and modern technologies. Mafic and ultramafic deposits represent low-grade yet abundant alternatives to traditional Ni and Co ores. Here, in this work, density functional theory (DFT) with the Hubbard U correction (DFT+U) was used to simulate the incorporation of Ni and Co in forsterite (Mg 2 SiO 4 ), the Mg endmember of olivine, a common mineral in mafic and ultramafic rocks. Hubbard U terms for Ni and Co were parametrized using a series of oxide, hydroxide, carbonate, silicate, and sulfide minerals relevant to extraction and recovery of Ni and Co from mafic and ultramafic deposits. Electronic, energetic, magnetic, and structural properties were considered in the parametrization. For each of Ni and Co, an effective Hubbard correction (U eff ) value that optimized agreement with either experimental data or a hybrid exchange-correlation functional for all of the minerals considered is reported. DFT+U ab initio molecular dynamics (AIMD) simulations of Ni and Co incorporated into the M1 and M2 octahedral sites of forsterite were then performed. Ni and Co substitution in the M1 site was more energetically favorable than substitution in the M2 site, in agreement with published partition coefficients. AIMD trajectories were used to compute extended X-ray absorption fine structure (EXAFS) spectra of Ni in the M1 and M2 sites for direct fitting to a published experimental spectrum of Ni in a natural San Carlos olivine sample. The results of the fit indicated that ordering of Ni in the M1 site was not as strong at the low Ni concentrations relevant to mafic and ultramafic silicate minerals as that at the higher concentrations of the Ni-Mg olivine solid solutions studied to date.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of thermal pretreatment and catalyst on biomass gasification efficiency and syngas composition

This work explores the combined effects of thermal pretreatment and using a catalyst in situ on gasification carbon conversion efficiency, as well as product gas and tar content and compositions. To compare the effects of thermal pretreatment, pelletized and ground oak with three different levels of thermal pretreatment were gasified in a fluidized bed reactor. The pretreatments applied to the oak were (1) pelletization, (2) drying at 180 °C in air, and (3) torrefaction at 270 °C in nitrogen. The oak dried at 180 °C produced syngas of similar quality and approximately the same amount of char as untreated oak. Torrefaction at 270 °C resulted in syngas with a higher hydrogen to CO ratio, lower methane, and less than half of the total tar -- all of which are desirable properties in terms of product gas quality. However, the oak torrefied at 270 °C also produced more than two times the amount of char as the untreated, pelletized oak. To determine the effect of catalyst, a series of experiments were conducted using olivine impregnated with nickel and cerium as the fluidized bed material in the gasifier. These tests showed that modified olivine can improve hydrogen production and reduce methane and tar levels in the syngas. The result was observed for both treated and untreated oak; although the effect was more substantial for untreated oak, for which the use of modified olivine reduced tar concentrations in the product gas by 60%, with a larger reduction in heavier tars than lighter tars. Furthermore, this result is important because reduction in heavier tar plays a more important role in benefitting downstream operations.

09 BIOMASS FUELS↗

Study of Chelyabinsk LL5 meteorite fragment with a light lithology and its fusion crust using Mössbauer spectroscopy with a high velocity resolution

Study of Chelyabinsk LL5 ordinary chondrite fragment with a light lithology and its fusion crust, fallen on February 15, 2013, in Russian Federation, was carried out using Mössbauer spectroscopy with a high velocity resolution. The Mössbauer spectra of the internal matter and fusion crust were fitted and all components were related to iron-bearing phases such as olivine, pyroxene, troilite, Fe-Ni-Co alloy, and chromite in the internal matter and olivine, pyroxene, troilite, Fe-Ni-Co alloy, and magnesioferrite in the fusion crust. A comparison of the content of different phases in the internal matter and in the fusion crust of this fragment showed that ferric compounds resulted from olivine, pyroxene, and troilite combustion in the atmosphere.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DIRECT LABORATORY ANALYSIS OF SILICATE STARDUST FROM RED GIANT STARS

We performed combined focused ion beam/transmission electron microscopy studies to investigate the chemistry and structure of eight presolar silicate grains that were previously detected by NanoSIMS oxygen isotope mapping of the carbonaceous chondrite Acfer 094. The analyzed presolar silicates belong to the O isotope Groups I/II ({sup 17}O-enriched and {sup 18}O-depleted) and therefore come from 1-2.5 M{sub sun} asymptotic giant branch stars of close-to-solar or slightly lower-than-solar metallicity. Three grains are amorphous, Mg-rich, and show a variable, but more pyroxene-like composition. Most probably, these grains have formed under circumstellar low-temperature conditions below the crystallization temperature. Three grains are Fe-bearing glasses similar to the 'glass with embedded metal and sulfides' (GEMS) grains found in interplanetary dust particles. However, two of the meteorite GEMS grains from this study lack comparatively large ({approx}>20 nm) Fe-rich inclusions and have sulfur contents <1 at.%, which is different than observed for the majority of GEMS grains. These grains likely condensed under strong non-equilibrium conditions from an Si-enriched gas. One olivine is characterized by a crystalline core and an amorphous, more Fe-rich rim, which is probably the result of interstellar medium sputtering combined with Mg removal. The detection of another olivine with a relatively high Fe content (Mg no. 0.9) shows that circumstellar crystalline silicates are more Fe-rich than astrophysical models usually suggest. The overall predominance of olivine among the crystalline silicate stardust population compared to pyroxene indicates preferential formation or survival of this type of mineral. As pyroxene is indeed detected in circumstellar outflows, it remains to be seen how this result is compatible with astrophysical observations and experimental data.

99 GENERAL AND MISCELLANEOUS↗

THE MINERALOGY AND STRUCTURE OF THE INNER DEBRIS DISK OF {beta} PICTORIS

We observed the edge-on, planet-bearing disk of {beta} Pictoris using T-ReCS at Gemini to clarify and extend previous observations and conclusions about this unique system. Our spectroscopy and spectral modeling of the 10 {mu}m silicate feature constrain the spatial distributions of three representative dust components (0.1 {mu}m/2.0 {mu}m glassy olivine and crystalline forsterite) across the inner 20 AU of the disk. We confirm that the 2.0 {mu}m glassy olivine is strongly peaked in the disk center and that the 0.1 {mu}m glassy olivine does not show this concentration, but rather is double peaked, with the peaks on either side of the star. However, we do not see the strong difference in brightness between those two peaks reported in a previous study. Although the spatial distribution of the 0.1 {mu}m dust is consistent with the scenario of a dust-replenishing planetesimal belt embedded in the disk, we note an alternative interpretation that can explain the spatial distributions of the 0.1 {mu}m and 2.0 {mu}m grains simultaneously and does not require the planetesimal belt. In addition to the spectroscopy, we also obtained a new 11.7 {mu}m image of the {beta} Pic disk. By comparing this image with that acquired in 2003, we confirm the existence and overall shape of the dusty clump at 52 AU in the SW disk. We speculate that the clump's projected spatial displacement of {approx}2.0 AU, a 3.6{sigma} result, between two epochs separated by seven years is due to the Keplerian motion of the clump at an orbital radius of 54.3{sup +2.0} {sub -1.2} AU.

79 ASTRONOMY AND ASTROPHYSICS↗

H{sub 2} formation in diffuse clouds: A new kinetic Monte Carlo study

We used the continuous-time random-walk Monte Carlo technique to study anew the formation of H{sub 2} on the surfaces of interstellar dust grains in diffuse interstellar clouds. For our study, we considered three different grain materials, olivine (a polycrystalline silicate), amorphous silicate, and amorphous carbon, as well as a grain temperature that depends on granular size. For some runs, we included temperature fluctuations. Four different granular surfaces were used, one 'flat' with one type of binding site due to physisorption, one 'rough' with five different types of physisorption binding sites due to lateral forces, and two with sites for chemisorption, one in which chemisorption sites are entered through precursor physisorption sites, and one in which chemisorption is direct but occurs with a barrier for the adsorption of the first hydrogen atom. We found that on flat and rough olivine surfaces, molecular hydrogen is formed at low efficiencies, with smaller grains contributing very little despite their large numbers due to high temperatures. For flat amorphous carbon and amorphous silicate surfaces, the efficiency increases, reaching unity for the largest grains. For models with barrierless chemisorption, the efficiency of formation of H{sub 2} is near unity at all grain sizes considered, while for direct chemisorption via a barrier, we found efficiencies of 0.13-0.6 depending upon the barrier, but independent of grain size. Treating the flat olivine and amorphous silicate surfaces with temperature fluctuations increases the efficiency of H{sub 2} formation.

79 ASTRONOMY AND ASTROPHYSICS↗

COMPOSITION OF POTENTIALLY HAZARDOUS ASTEROID (214869) 2007 PA8: AN H CHONDRITE FROM THE OUTER ASTEROID BELT

Potentially hazardous asteroids (PHAs) represent a unique opportunity for physical characterization during their close approaches to Earth. The proximity of these asteroids makes them accessible for sample-return and manned missions, but could also represent a risk for life on Earth in the event of collision. Therefore, a detailed mineralogical analysis is a key component in planning future exploration missions and developing appropriate mitigation strategies. In this study we present near-infrared spectra (∼0.7–2.55 μm) of PHA (214869) 2007 PA8 obtained with the NASA Infrared Telescope Facility during its close approach to Earth on 2012 November. The mineralogical analysis of this asteroid revealed a surface composition consistent with H ordinary chondrites. In particular, we found that the olivine and pyroxene chemistries of 2007 PA8 are Fa{sub 18}(Fo{sub 82}) and Fs{sub 16}, respectively. The olivine–pyroxene abundance ratio was estimated to be 47%. This low olivine abundance and the measured band parameters, close to the H4 and H5 chondrites, suggest that the parent body of 2007 PA8 experienced thermal metamorphism before being catastrophically disrupted. Based on the compositional affinity, proximity to the J5:2 resonance, and estimated flux of resonant objects we determined that the Koronis family is the most likely source region for 2007 PA8.

79 ASTRONOMY AND ASTROPHYSICS↗

Influence of Bulk Chemical Composition on Relative Sensitivity Factors for 55Mn/52Cr by SIMS: Implications for the 53Mn-53Cr Chronometer

The {sup 53}Mn-{sup 53}Cr systematics of meteorite samples provide an important high resolution chronometer for early solar system events. Accurate determination of the initial abundance of {sup 53}Mn ({tau}{sub 1/2} = 3.7 Ma) by secondary ion mass spectrometry (SIMS) is dependent on properly correcting for differing ion yields between Mn and Cr by use of a relative sensitivity factor (RSF). Ideal standards for SIMS analysis should be compositionally and structurally similar to the sample of interest. However, previously published Mn-Cr studies rely on few standards (e.g., San Carlos olivine, NIST 610 glass) despite significant variations in chemical composition. We investigate a potential correlation between RSF and bulk chemical composition by determining RSFs for {sup 55}Mn/{sup 52}Cr in 11 silicate glass and mineral standards (San Carlos olivine, Mainz glasses KL2-G, ML3B-G, StHs6/80-G, GOR128-G, BM90/21-G, and T1-G, NIST 610 glass, and three LLNL pyroxene-composition glasses). All standards were measured on the Cameca ims-3f ion microprobe at LLNL, and a subset were also measured on the Cameca ims-1270 ion microprobe at the Geological Survey of Japan. The standards cover a range of bulk chemical compositions with SiO{sub 2} contents of 40-71 wt.%, FeO contents of 0.05-20 wt.% and Mn/Cr ratios between 0.4 and 58. We obtained RSF values ranging from 0.83 to 1.15. The data obtained on the ims-1270 ion microprobe are within {approx}10% of the RSF values obtained on the ims-3f ion microprobe, and the RSF determined for San Carlos olivine (0.86) is in good agreement with previously published data. The typical approach to calculating an RSF from multiple standard measurements involves making a linear fit to measured {sup 55}Mn/{sup 52}Cr versus true {sup 55}Mn/{sup 52}Cr. This approach may be satisfactory for materials of similar composition, but fails when compositions vary significantly. This is best illustrated by the {approx}30% change in RSF we see between glasses with similar Mn/Cr ratios but variable Fe and Na content. We are developing an approach that uses multivariate analysis to evaluate the importance of different chemical components in controlling the RSF and predict the RSF of unknowns when standards of appropriate composition are not available. Our analysis suggests that Fe, Si, and Na are key compositional factors in these silicate standards. The RSF is positively correlated with Fe and Si and negatively correlated with Na. Work is currently underway to extend this analysis to a wider range of chemical compositions and to evaluate the variability of RSF on measurements obtained by NanoSIMS.

58 GEOSCIENCES↗

Visible/near-infrared spectral diversity from in situ observations of the Bagnold Dune Field sands in Gale Crater, Mars

As part of the Bagnold Dune campaign conducted by Mars Science Laboratory rover Curiosity, visible/near–infrared reflectance spectra of dune sands were acquired using Mast Camera (Mastcam) multispectral imaging (445–1013 nm) and Chemistry and Camera (ChemCam) passive point spectroscopy (400–840 nm). By comparing spectra from pristine and rover–disturbed ripple crests and troughs within the dune field, and through analysis of sieved grain size fractions, constraints on mineral segregation from grain sorting could be determined. In general, the dune areas exhibited low relative reflectance, a weak ~530 nm absorption band, an absorption band near 620 nm, and a spectral downturn after ~685 nm consistent with olivine–bearing sands. The finest grain size fractions occurred within ripple troughs and in the subsurface and typically exhibited the strongest ~530 nm bands, highest relative reflectances, and weakest red/near–infrared ratios, consistent with a combination of crystalline and amorphous ferric materials. Coarser–grained samples were the darkest and bluest and exhibited weaker ~530 nm bands, lower relative reflectances, and stronger downturns in the near–infrared, consistent with greater proportions of mafic minerals such as olivine and pyroxene. These grains were typically segregated along ripple crests and among the upper surfaces of grain flows in disturbed sands. Sieved dune sands exhibited progressive decreases in reflectance with increasing grain size, as observed in laboratory spectra of olivine size separates. In conclusion, the continuum of spectral features observed between the coarse– and fine–grained dune sands suggests that mafic grains, ferric materials, and air fall dust mix in variable proportions depending on aeolian activity and grain sorting.

79 ASTRONOMY AND ASTROPHYSICS↗

Diffusion Creep of Enstatite at High Pressures Under Hydrous Conditions: Diffusion Creep of Hydrous Enstatite

Mantle convection and large-scale plate motion depend critically on the nature of the lithosphere-asthenosphere boundary and thus on the viscosity structure of Earth's upper mantle, which is determined by the rheological properties of its constituent minerals. To constrain the flow behavior of orthopyroxene, the second most abundant constituent of the upper mantle, deformation experiments were carried out in triaxial compressive creep on fine-grained (~6 μm) samples of enstatite at high pressures (3.8–6.3 GPa) and high temperatures (1323–1573 K) using a deformation-DIA apparatus. Based on results from this study, the deformation behavior of enstatite is quantitatively presented in the form of a flow law that describes the dependence of deformation rate on differential stress, water fugacity, temperature, and pressure. Specifically, the creep rate depends approximately linearly on stress, indicating deformation in the diffusion creep regime. A least squares regression fit to our data yielded a flow law for diffusion creep with an activation energy of ~200 kJ/mol and an activation volume of ~14 × 10 -6 m 3 /mol. The magnitude of the water-weakening effect is similar to that for olivine with a water fugacity exponent of r ≈ 0.7. This strong dependence of viscosity on water fugacity (concentration) indicates that the viscosity of an orthopyroxene-bearing mantle varies from one geological setting to another, depending on the large-scale water distribution. Based on the rheology contrast between olivine and enstatite, we conclude that olivine is weaker than enstatite throughout most of the upper mantle except in some shallow regions in the diffusion creep regime.

36 MATERIALS SCIENCE↗

Modern water/rock reactions in Oman hyperalkaline peridotite aquifers and implications for microbial habitability

The Samail ophiolite in Oman is undergoing modern hydration and carbonation of peridotite and may host a deep subsurface biosphere. Previous investigations of hyperalkaline fluids in Oman have focused on fluids released at surface seeps, which quickly lose their reducing character and precipitate carbonates upon contact with the O 2 /CO 2 -rich atmosphere. In this study, geochemical analysis of rocks and fluids from the subsurface provides new insights into the operative reactions in serpentinizing aquifers. Serpentinite rock and hyperalkaline fluids (pH > 10), which exhibit millimolar concentrations of Ca 2+ , H 2 and CH 4 , as well as variable sulfate and nitrate, were accessed from wells situated in mantle peridotite near Ibra and studied to investigate their aqueous geochemistry, gas concentrations, isotopic signatures, mineralogy, Fe speciation and microbial community composition.The bulk mineralogy of drill cuttings is dominated by olivine, pyroxene, brucite, serpentine and magnetite. At depth, Fe-bearing brucite is commonly intermixed with serpentine, whereas near the surface, olivine and brucite are lost and increased magnetite and serpentine is detected. Micro-Raman spectroscopy reveals at least two distinct generations of serpentine present in drill cuttings recovered from several depths from two wells. Fe K-edge X-ray absorption near-edge spectroscopy (XANES) analysis of the lizardite shows a strong tetrahedral Fe coordination, suggesting a mixture of both Fe(II) and Fe(III) in the serpentine. Magnetite veins are also closely associated with this second generation serpentine, and 2-10 μm magnetite grains overprint all minerals in the drill cuttings. Thus we propose that the dissolved H 2 that accumulates in the subsurface hyperalkaline fluids was evolved through low temperature oxidation and hydration of relict olivine, as well as destabilization of pre-existing brucite present in the partially serpentinized dunites and harzburgites. In particular, we hypothesize that Fe-bearing brucite is currently reacting with dissolved silica in the aquifer fluids to generate late-stage magnetite, additional serpentine and dissolved H 2 . Dissolved CH 4 in the fluids exhibits the most isotopically heavy carbon in CH 4 reported in the literature thus far. The CH 4 may have formed through abiotic reduction of dissolved CO 2 or through biogenic pathways under extreme carbon limitation. The methane isotopic composition may have also been modified by significant methane oxidation. 16S rRNA sequencing of DNA recovered from filtered hyperalkaline well fluids reveals an abundance of Meiothermus, Thermodesulfovibrionaceae (sulfate-reducers) and Clostridia (fermenters). The fluids also contain candidate phyla OP1 and OD1, as well as Methanobacterium (methanogen) and Methylococcus sp. (methanotroph). Finally, the composition of these microbial communities suggests that low-temperature hydrogen and methane generation, coupled with the presence of electron acceptors such as nitrate and sulfate, sustains subsurface microbial life within the Oman ophiolite.

58 GEOSCIENCES↗

Titanium, vanadium and chromium valences in silicates of ungrouped achondrite NWA 7325 and ureilite Y-791538 record highly-reduced origins

Titanium, Cr, and V valences were determined by applying micro-X-ray Absorption Near Edge Structure (micro-XANES) spectroscopy methods to individual grains of olivine and pyroxene in the ungrouped achondrite NWA 7325 and ureilite Y-791538, as well as to plagioclase in NWA 7325. The advantages of applying multiple, multivalent-element-based oxybarometers to individual grains are (1) the ability to cover the entire oxygen fugacity (fO2) range encountered in nature, and (2) the increased reliability from consistent results for semi-independent fO2 proxies. fO2 values were inferred from each mineral valence determination after correcting with available laboratory-experiment-derived, valence-specific partition coefficients to obtain melt valences and then calibrating with the fO2 values of the relevant equal species proportions points suggested for igneous (primarily basaltic) systems. The resulting olivine and pyroxene valences are highly reduced and similar in the two meteorites with substantial fractions of Cr2+, Ti3+ and V2+. The exception is Cr in NWA 7325 pyroxene which is much more oxidized than the Cr in its olivine. Chromium and Ti in plagioclase in NWA 7325 is relatively oxidized (V valence not determined). The anomalously oxidized Cr in NWA 7325 pyroxene may be due to a secondary reheating event that oxidized Cr in the pyroxene without similarly oxidizing Ti and V. Such a separation of the redox couples may be an effect of re-equilibration kinetics, where the valence of Cr would be more rapidly modified. These valences yielded similar mean fO2s for the two meteorites; IW-3.1 ± 0.2 for NWA 7325 and IW-2.8 ± 0.2 for Y-791538, consistent with an origin of NWA 7325 in either Mercury or an asteroid that experienced redox conditions similar to those on the ureilite parent body.

58 GEOSCIENCES↗

Synthesis and characterization of metastable, 20 nm-sized Pna2{sub 1}-LiCoPO{sub 4} nanospheres

The majority of research activities on LiCoPO{sub 4} are focused on the phospho-olivine (space group Pnma), which is a promising high-voltage cathode material for Li-ion batteries. In contrast, comparably little is known about its metastable Pna2{sub 1} modification. Herein, we present a comprehensive study on the structure–property relationships of 15–20 nm Pna2{sub 1}-LiCoPO{sub 4} nanospheres prepared by a simple microwave-assisted solvothermal process. Unlike previous reports, the results indicate that the compound is non-stoichiometric and shows cation-mixing with Co ions on the Li sites, which provides an explanation for the poor electrochemical performance. Co L{sub 2,3}-edge X-ray absorption spectroscopic data confirm the local tetrahedral symmetry of Co{sup 2+}. Comprehensive studies on the thermal stability using thermogravimetric analysis, differential scanning calorimetry, and in situ powder X-ray diffraction show an exothermic phase transition to olivine Pnma-LiCoPO{sub 4} at 527 °C. The influence of the atmosphere and the particle size on the thermal stability is also investigated. - Graphical abstract: Blue nano-sized Pna2{sub 1}-LiCoPO{sub 4,} featuring tetrahedrally-coordinated Co{sup 2+}, was synthesized in a rapid one-step microwave-assisted solvothermal process. The phase relation between this metastable and the stable polymorph was analyzed and electrochemical properties are discussed. - Highlights: • Preparation of uniform 15–20 nm nanospheres of metastable Pna2{sub 1}-LiCoPO{sub 4} polymorph. • Structure redetermination shows cation-mixing (Co blocking Li sites). • In situ investigation of phase transformation to olivine Pnma-LiCoPO{sub 4} at 527 °C. • Pna2{sub 1}-LiCoPO{sub 4} reemerges as a stable high-temperature phase above 800 °C. • X-ray absorption spectroscopy confirms local tetrahedral symmetry (T{sub d} Co{sup 2+}).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Direct synthesis and characterization of mixed-valent Li 0.5$-$δ CoPO 4 , a Li-deficient derivative of the Cmcm polymorph of LiCoPO 4

While the majority of research activities on LiCoPO 4 is focussed on the thermodynamically stable olivine-type Pnma polymorph, the metastable Pna 2 1 and Cmcm modifications have recently attracted considerable attention due to their interesting material properties. In this study, we present the first Li-deficient structural derivative of the Cmcm modification with the nominal composition Li 0.5–δ CoPO 4 . As opposed to the substoichiometric olivine ( Pnma ) phases Li x CoPO 4 (x = 0; 2/3), which are exclusively accessible by electrochemical or chemical Li extraction techniques, this is also the first time that a direct soft-chemical synthesis route towards a Li x CoPO 4 -type material is accomplished. X-ray and neutron diffraction studies indicate that Cmcm -type Li 0.5–δ CoPO 4 shows vacancies on both the Li and Co sites, whereas X-ray absorption spectra demonstrate that the structure features heterovalent Co ions (+2/+3) to compensate for the Li deficit. Magnetic measurements reveal a long-range antiferromagnetic order below 10.5 K. A thorough investigation of the thermal stability using thermogravimetric analysis, differential scanning calorimetry, and temperature-dependent in situ X-ray powder diffraction demonstrates that Li 0.5–δ CoPO 4 is metastable and exhibits a complex, multi-step thermal decomposition mechanism. In the first step at 394 °C, it decomposes to α-Co 2 P 2 O 7 ( P 2 1 /c) and LiCoPO 4 ( Cmcm ) upon O 2 release. The LiCoPO 4 ( Cmcm ) intermediate is then irreversibly transformed to olivine-type LiCoPO 4 (Pnma) at 686 °C. Furthermore, the material properties of Li 0.5–δ CoPO 4 are further compared to the fully lithiated, isostructural LiCoPO 4 ( Cmcm ) phase, for which an improved structure solution as well as Co L 2,3 -edge X-ray absorption spectra are reported for the first time.

36 MATERIALS SCIENCE↗

Oxygen isotope characteristics of chondrules from the Yamato-82094 ungrouped carbonaceous chondrite: Further evidence for common O-isotope environments sampled among carbonaceous chondrites

In this study, high-precision secondary ion mass spectrometry (SIMS) was employed to investigate oxygen three isotopes of phenocrysts in 35 chondrules from the Yamato (Y) 82094 ungrouped 3.2 carbonaceous chondrite. Twenty-one of 21 chondrules have multiple homogeneous pyroxene data (Δ 17 O 3SD analytical uncertainty: 0.7‰); 17 of 17 chondrules have multiple homogeneous pyroxene and plagioclase data. Twenty-one of 25 chondrules have one or more olivine data matching coexisting pyroxene data. Such homogeneous phenocrysts (1) are interpreted to have crystallized from the final chondrule melt, defining host O-isotope ratios; and (2) suggest efficient O-isotope exchange between ambient gas and chondrule melt during formation. Host values plot within 0.7‰ of the primitive chondrule mineral (PCM) line. Seventeen chondrules have relict olivine and/or spinel, with some δ 17 O and δ 18 O values approaching -40‰, similar to CAI or AOA-like precursors. Regarding host chondrule data, 22 of 34 have Mg#s of 98.8–99.5 and Δ 17 O of -3.9‰ to -6.1‰, consistent with most Acfer 094, CO, CR, and CV chondrite chondrules, and suggesting a common reduced O-isotope reservoir devoid of 16 O-poor H 2 O. Six Y-82094 chondrules have Δ 17 O near -2.5‰, with Mg#s of 64–97, consistent with lower Mg# chondrules from Acfer 094, CO, CR, and CV chondrites; their signatures suggest precursors consisting of those forming Mg# ~99, Δ 17 O: -5‰ ± 1‰ chondrules plus 16 O-poor H 2 O, at high dust enrichments. Three type II chondrules plot slightly above the PCM line, near the terrestrial fractionation line (Δ 17 O: ~+0.1‰). Their O-isotopes and olivine chemistry are like LL3 type II chondrules, suggesting they sampled ordinary chondrite-like chondrule precursors. Finally, three Mg# >99 chondrules have Δ 17 O of -6.7‰ to -8.1‰, potentially due to 16 O-rich refractory precursor components. Finally, the predominance of Mg# ~99, Δ 17 O: -5‰ ± 1‰ chondrules and a high chondrule-to-matrix ratio suggests bulk Y-82094 characteristics are closely related to anhydrous dust sampled by most carbonaceous chondrite chondrules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Metasomatic alteration of coarse‐grained igneous calcium‐aluminum‐rich inclusions from CK3 carbonaceous chondrites

Abstract We report on the primary and secondary mineralogies of three coarse‐grained igneous calcium‐aluminum‐rich inclusions (CAIs) (Compact Type A [CTA], Type B [B], and forsterite‐bearing type B [FoB]) from the Northwest Africa (NWA) 5343 (CK3.7) and NWA 4964 (CK3.8) carbonaceous chondrites, compare them with the mineralogy of igneous CAIs from the Allende (CV3.6) chondrite, and discuss the nature of the alteration processes that affected the CK and CV CAIs. The primary mineralogy and mineral chemistry of the CK3 CAIs studied are similar to those from Allende; however, primary melilite and anorthite are nearly completely absent. Although the secondary minerals identified in CK CAIs (Al‐diopside, andradite, Cl‐apatite, clintonite, forsterite, ferroan olivine, Fe,Ni‐sulfides, grossular, ilmenite, magnetite, plagioclase, spinel, titanite, and wadalite) occur also in the Allende CAIs, there are several important differences: (i) In addition to melilite and anorthite, which are nearly completely replaced by secondary minerals, the alteration of CK CAIs also affected high‐Ti pyroxenes (fassaite and grossmanite) characterized by high Ti 3+ /Ti 4+ ratio and spinel. These pyroxenes are corroded and crosscut by veins of Fe‐ and Ti‐bearing grossular, Fe‐bearing Al,Ti‐diopside, titanite, and ilmenite. Spinel is corroded by Fe‐bearing Al‐diopside and grossular. (ii) The secondary mineral assemblages of grossular + monticellite and grossular + wollastonite, commonly observed in the Allende CAIs, are absent; the Fe‐bearing grossular + Fe‐bearing Al‐diopside ± Fe,Mg‐spinel, Fe‐bearing grossular + Fe,Mg‐olivine ± Fe,Mg‐spinel, and Ca,Na‐plagioclase + Fe‐bearing Al‐diopside + Fe‐bearing grossular assemblages are present instead. These mineral assemblages are often crosscut by veins of Fe‐bearing Al‐diopside, Fe,Mg‐olivine, Fe,Mg‐spinel, and Ca,Na‐plagioclase. The coarse‐grained secondary grossular and Al‐diopside often show multilayered chemical zoning with distinct compositional boundaries between the layers; the abundances of Fe and Ti typically increase toward the grain edges. (iv) Sodium‐rich secondary minerals, nepheline and sodalite, commonly observed in the peripheral portions of the Allende CAIs, are absent; Ca,Na‐plagioclase is present instead. We conclude that coarse‐grained igneous CAIs from CK3.7–3.8 s and Allende experienced an open‐system multistage metasomatic alteration in the presence of an aqueous solution–infiltration metasomatism. This process resulted in localized mobilization of all major rock‐forming elements: Si, Ca, Al, Ti, Mg, Fe, Mn, Na, K, and Cl. The metasomatic alteration of CK CAIs is more advanced and occurred under higher temperature and higher oxygen fugacity than that of the Allende CAIs.

Geochemistry & Geophysics↗