Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nuclear forensics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Evaluation of SR/ TEVA/ TRU triple stack for separation of activation products

A rapid method to separate Ta, Po, Au, Pt, and W from a sample containing mixed fission and activation products was developed using three commercially available extraction chromatography resins stacked in series. When the separation was tested using all the target activation products, even those with short half-lives were measurable. Finally, combining multiple extraction chromatography resin cartridges in tandem allows for multiple short-lived activation products to be separated from one sample addition without the complication of multiple steps.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Field deployable trace radioisotope analysis through combined electrochemical and alpha spectroscopy methods

A method for depositing actinides directly onto a 4H-SiC Schottky barrier diode (SBD) detector as a field deployable actinides sensor was developed to enable off-site analysis, shortening the time to obtain critical information such as elements, concentration, and/or isotopic ratio related to the radiological situation. A thin film of Hg was first electrodeposited onto the Pt contact of the SiC diode, followed by chronoamperometric deposition of microgram levels of actinides under conventional control conditions. The 4H-SiC diode maintained consistent functionality through the electrodeposition process and showed resolved alpha-energy spectra that contained accurate isotopic information demonstrating the feasibility of a combined chemical and radiological sensor for field actinide detection and quantification.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Radioisotope dating of nuclear materials using cryogenic decay energy spectrometry

Cryogenic decay energy spectrometry provides high energy resolution and enables absolute decay counting, offering an alternative measurement technique for radiochronometry. A cryogenic decay energy spectrometry experiment was conducted using a magnetic microcalorimeter to determine the age of a plutonium sample. The energy resolution was measured at 0.05% from 5 to 6 MeV. The time since sample purification was determined using the measured concentration ratio of the 241 Am/ 241 Pu radiochronometer. Sample age estimates based on 241 Pu alpha-decay and beta-decay counts, along with 241 Am decay counts, align with the expected sample age within expanded uncertainty (k = 2), supporting the accuracy of cryogenic decay energy spectrometry as a radiochronometric method.

and nuclear chemistry↗

Hydrogen and oxygen stable isotope composition of water in metaschoepite mineralization on U 3 O 8

When exposed to humidity in an oxidizing atmosphere hydrated uranium oxide grows as a secondary mineral on aged U 3 O 8 and may incorporate the oxygen stable isotope signature of the water vapor into the secondary uranium oxide, as well as hydrogen and oxygen stable isotopes into any mineral hydration water. Because geospatial variation in δ 2 H and δ 18 O values of atmospheric humidity and precipitation is well understood, the H and O stable isotope composition of mineral hydration waters can give information on the environment of mineral formation. We exposed powdered U 3 O 8 to humidity with known H and O stable isotope composition at constant 30%, 61% and 91% relative humidity. We sampled and analyzed the U 3 O 8 powders along with any secondary hydrated minerals that had formed on the particle surfaces at various intervals from 1 to 10 days throughout the 180-day humidity exposures. We present stable H and O isotope results of mineral hydration waters in uranium oxide materials analyzed by thermogravimetry-enabled isotope ratio infrared spectroscopy (TGA-IRIS), which uses precise heating by thermogravimetric analyzer to liberate water vapor for subsequent online isotope analysis via a laser-based isotope ratio infrared spectroscopy instrument (Picarro L-2130i). Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and x-ray diffraction (XRD) analysis of humidity-exposed U 3 O 8 heated to 350 °C indicates that the U 3 O 8 had a measurable metaschoepite ((UO 3 )•2H 2 O) phase along with α-U 3 O 8 . After heating to 350 °C, the metaschoepite is eliminated but the α-U 3 O 8 is retained, meaning that the heating successfully extracted the water in the metaschoepite but did not disturb the crystalline structure of the U 3 O 8 . Analysis of the bulk oxygen isotope composition by fluorination of these samples before and after heating, indicates that the oxygen isotope value of the U 3 O 8 is also not affected by heating to 350 °C. Precision for δ 2 H and δ 18 O values of metaschoepite mineral hydration water stable isotope values yielded by the TGA-IRIS method on metaschoepite are 5.86‰ for δ 2 H, and 0.34‰ for δ 18 O. Hydrogen in the various water reservoirs is highly exchangeable and thus the δ 2 H values of these waters is not easily interpreted. However, oxygen in the separate water reservoirs is much less exchangeable, and thus δ 18 O values of the metaschoepite mineral hydration water is likely to reflect that of the water vapor the sample was exposed to. Once metaschoepite is formed on the surface of U 3 O 8 particles, the oxygen isotope signature of the mineral hydration water in metaschoepite does not respond to changes in exposure vapor isotopic composition, and thus appears to be fairly durable in this regard. Furthermore, these results suggest that it may be possible to discern information about the provenance and history of an oxidized U 3 O 8 sample from oxygen stable isotope measurements of metaschoepite mineral hydration water.

07 ISOTOPE AND RADIATION SOURCES↗

The oxygen stable isotope composition of CRM 125-A UO 2 standard reference material

While there is a clear need for standardized reference materials for analytical calibrations and for inter-laboratory comparisons, there are not currently any for the oxygen stable isotopic composition of uranium oxides. In this paper we summarize the results from four laboratories by seven different methods of oxygen stable isotope analyses using fluorination techniques of CRM 125-A UO 2 Standard Reference Material. We synthesize these data and methods to arrive at a consensus oxygen stable isotope composition for CRM 125-A $δ$ 18 O = -9.63‰ (±0.29‰) VSMOW. We discuss methodological differences between analytical approaches, including furnace vs laser heating, fluorination using BrF 5 or ClF 3 , as well as calibration strategies. We highlight the potential effects of calibration scale compression from single-point calibrations using reference material with $δ$ 18 O values having a large relative difference from the sample being analyzed. We demonstrate how calibration scale compression can yield differences in calibrated $δ$ 18 O values up to ~2‰ for samples with ~20‰ difference from a single reference material, if the calibration slope of different analytical systems differs by 0.1. In conclusion, we suggest the use of liquid water calibration standards sealed in silver capillary tubes for multi-point calibrations of fluorination analysis systems.

07 ISOTOPE AND RADIATION SOURCES↗

Production and separation of carrier-free 7 Be

A high-purity carrier-free 7 Be was efficiently isolated following proton bombardment of a lithium hydroxide - aluminum target. The separation of beryllium from lithium and aluminum was achieved through a hydrochloric acid elution system utilizing cation exchange chromatography. The beryllium recovery, +99%, was assessed through gamma spectroscopy while the chemical purity was established by mass spectrometry. In conclusion, the decontamination factors of beryllium from lithium and aluminum were determined to be 6900 and 300, respectively.

07 ISOTOPE AND RADIATION SOURCES↗

Half-life determination and comparison of activity standards of 231 Pa

The results of an international comparison of activity measurements of a solution of 231 Pa are reported and analysed. Prior to this, no known standardisation of 231 Pa by activity measurement had been carried out. The comparison was run in 2017–2018 involving eight laboratories, and returned results with no identifiable inconsistencies between methods or laboratories. The results, including one mass determination, gave a 231 Pa activity concentration of 41.461(48) kBq g -1 and a 231 Pa atom concentration of 61.48(23) × 10 15 atoms g -1 , from which a half-life value of 32 570(130) years was derived.

Half-life↗

Improving microstructures segmentation via pretraining with synthetic data

Image analysis of material microstructures through microscopy is an integral capability in the field of materials science. The topological and chemical information obtained through microscopy allow us to draw vital connections between material microstructures, properties, and processing. While scanning electron microscopy (SEM) is able to yield a considerable wealth of information interpretable by the intuition of experts, there has been considerable interest in using machine learning, convolutional neural networks (CNNs) in particular, for such image analysis task. Training CNNs for an image analysis task requires a large annotated dataset. However, in many materials science applications, obtaining a large annotated dataset is cost and labor intensive. In this work, we study the use of synthetic data to enlarge the available annotated experimental data of uranium oxide. We utilize a modified Potts model to simulate uranium oxide particles with morphologies similar to those observed experimentally. We then leverage an image-to-image translation model to synthesize the simulated particles as if they are acquired with SEM. Through this process, we obtain pairs of particle images and their corresponding SEM representations, which corresponds to pairs of annotations and images. Unlike previous works, we leverage synthetic data for pretraining a CNN model prior, and finetune that model further with experimental data. We experimentally demonstrate that using synthetic data as incremental learning process benefits the overall performance compared to training a model on combined synthetic and experimental data.

36 MATERIALS SCIENCE↗

Optical vibrational spectroscopic signatures of ammonium diuranate process parameters

Ammonium diuranate (ADU) is commonly encountered in the nuclear fuel cycle; however, previous investigations have shown that ADU is a complex mixture of distinct compounds. Moreover, production parameters are known to heavily influence the composition of the resulting ADU. Here, we examine four samples of ADU prepared at Oak Ridge National Laboratory (ORNL), and one sample of ADU made at Pacific Northwest National Laboratory (PNNL), with the goal of further characterizing and elucidating the effect of processing parameters such as stir rate, strike direction, and temperature on material composition. Process parameters during ADU precipitation at ORNL and PNNL were well documented, and we relate process variables to optical vibrational spectroscopic signatures observed using Raman and infrared (IR) spectroscopy. In addition, powder X-ray diffraction (PXRD) reveals differences in the solid-phase composition of ADU precipitates, but we find that the primary phase is similar to the uranyl oxyhydroxyhydrate mineral metaschoepite. Despite the significant phase contributions of a metaschoepite-like phase, spectroscopic evidence of both nitrate and ammonium are observed for all samples. To gain a more holistic understanding of spectroscopic features of process parameters in ADU, principal component analysis (PCA) is employed and results in observable signatures that relate to the stir rate used during synthesis. These results provide further information about the process-dependence of ADU precipitate composition.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Enhanced ionization efficiency in TIMS analyses of plutonium and americium using porous ion emitters

Investigations of enhanced sample utilization in thermal ionization mass spectrometry (TIMS) using porous ion emitter (PIE) techniques for the analyses of trace quantities of americium and plutonium were performed. Repeat ionization efficiency (i.e., the ratio of ions detected to atoms loaded on the filament) measurements were conducted on sample sizes ranging from 10–100 pg for americium and 1–100 pg for plutonium using PIE and traditional (i.e., a single, zone-refined rhenium, flat filament ribbon with a carbon ionization enhancer) TIMS filament sources. When compared to traditional filaments, PIEs exhibited an average boost in ionization efficiency of ~550% for plutonium and ~1100% for americium. A maximum average efficiency of 1.09% was observed at a 1 pg plutonium sample loading using PIEs. Supplementary trials were conducted using newly developed platinum PIEs to analyze 10 pg mass loadings of plutonium. As a result, platinum PIEs exhibited an additional ~134% boost in ion yield over standard PIEs and ~736% over traditional filaments at the same sample loading level.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Isotopic fractionation studies of uranium and plutonium using porous ion emitters as thermal ionization mass spectrometry sources

Investigations of the isotope fractionation behaviors of plutonium and uranium reference standards were conducted employing platinum and rhenium (Pt/Re) porous ion emitter (PIE) sources, a relatively new thermal ionization mass spectrometry (TIMS) ion source strategy. The suitability of commonly employed, empirically developed mass bias correction laws (i.e., the Linear, Power, and Russell's laws) for correcting such isotope ratio data was also determined. Corrected plutonium isotope ratio data, regardless of mass bias correction strategy, were statistically identical to that of the certificate, however, the process of isotope fractionation behavior of plutonium using the adopted experimental conditions was determined to be best described by the Power law. Finally, the fractionation behavior of uranium, using the analytical conditions described herein, is also most suitably modeled using the Power law, though Russell's and the Linear law for mass bias correction rendered results that were identical, within uncertainty, to the certificate value.

07 ISOTOPE AND RADIATION SOURCES↗

Spatially-Resolved Analyses of Aerodynamic Fallout from a Uranium-Fueled Nuclear Test

The fiive silicate fallout glass spherules produced in a uranium-fueled, near-surface nuclear test were characterized by secondary ion mass spectrometry, electron probe microanalysis, autoradiography, scanning electron microscopy, and energy-dispersive x-ray spectroscopy. Several samples display compositional heterogeneity suggestive of incomplete mixing between major elements and natural U ( 238 U/ 235 U = 0.00725) and enriched U. Samples exhibit extreme spatial heterogeneity in U isotopic composition with 0.02 < 235 U/ 238 U < 11.84 among all five spherules and 0.02 < 235 U/ 238 U < 7.41 within a single spherule. Moreover, in two spherules, the 235 U/ 238 U ratio is correlated with changes in major element composition, suggesting the agglomeration of chemically and isotopically distinct molten precursors. Two samples are nearly homogenous with respect to major element and uranium isotopic composition, suggesting extensive mixing possibly due to experiencing higher temperatures or residing longer in the fireball. Linear correlations between 234 U/ 238 U, 235 U/ 238 U, and 236 U/ 238 U ratios are consistent with a two-component mixing model, which is used to illustrate the extent of mixing between natural and enriched U end members.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Morphological and chemical characteristics of oxide scales formed on δ-Phase plutonium metal alloys I: 3.5 at% ga

Focused ion-beam scanning electron microscopy (FIB-SEM) and three-dimensional (3D) microscopy were applied to characterize the subsurface morphological features of oxide scales formed on an ~3.5 at.% Ga plutonium (Pu) metal alloy. Using the FIB-SEM technique, a number of morphological features formed in the interior of the oxide scale from Pu metal's environmental exposure were observed and identified. Here, Auger electron spectroscopy (AES) was utilized to characterize the cross-sectional composition and chemistry of the oxide scale. The oxide scale formed during inert storage and operational environments has a characteristic internal scale structure that includes a relatively dense oxide layer with some lateral and transverse cracking. Generally, after subsequent exposure to dry air environment, the oxide scale retained most of the original structural and chemical characteristics. However, after aging in a moist air environment, while the oxide scale was found to maintain the chemical characteristics of the source oxide, the scale was found to be on average thinner and without the previously observed internal microcracking, likely the result of spallation of the source scale during exposure to the new environment.

36 MATERIALS SCIENCE↗

Morphological and chemical characteristics of oxide scales formed on δ-phase plutonium metal alloys II: 2.0 at% Ga

The focused ion-beam scanning electron microscopy (FIB-SEM) and three-dimensional (3D) microscopy were applied to characterize the subsurface morphological features of oxide scales formed on an ~2.0 at. % Ga plutonium (Pu) metal alloy. Using the FIB-SEM technique, a number of morphological features formed in the interior of the oxide scale from Pu metal’s environmental exposure were observed and identified. Auger electron spectroscopy (AES) was utilized to characterize the cross-sectional composition and chemistry of the oxide scale. The oxide scale formed during inert storage and operational environments was found to be highly variable in thickness and morphology, presenting some regions with a thin (<400 nm), dense oxide layer and others with a thick (>2 µm) scale with substantial lateral cracking. After subsequent exposure to dry air environment, the oxide scale became thicker (~4 µm) and slightly more porous. The changes following aging in a moist air environment were observed to be more severe, with the formation of a highly porous internal structure containing significant lateral and transverse cracking. In comparison to the scale formed on an ~3.5 at. % Ga-Pu metal alloy, the oxide morphology of the lower gallium alloy investigated here exhibited greater variation in thickness and a noteworthy dependence on the presence of water vapor, particularly in terms of the internal porosity formed during growth of the oxide.

36 MATERIALS SCIENCE↗

Molybdenum and Tungsten isotope compositions of UO 2 fuel pellets: Implications for isotopically enriched taggants

The addition of isotopically enriched taggants to material at the front end of the nuclear fuel cycle could be a powerful tool used to assist law enforcement authorities should material outside of regulatory control be found. Two potential candidates for this purpose are molybdenum (Mo) and tungsten (W) as both elements have five or more stable isotopes and are trace elements contained within nuclear fuel. So there is a concern that Mo and W could undergo isotope fractionation during processes like uranium enrichment and to date, it is unknown if nuclear fuels have natural Mo and W isotope compositions. If Mo and W isotopic variability is present in nuclear fuels, this would hinder the use of these elements as isotopic taggants because it would be difficult to discern the original taggant isotope composition with high confidence. Therefore, a set of 16 low enriched uranium (LEU) fuel pellets from US commercial producers was analyzed using multi collector-inductively coupled plasma mass spectrometry (MC-ICPMS) to determine Mo and W isotope compositions (i.e., 94 Mo/ 92 Mo, 95 Mo/ 92 Mo, 96 Mo/ 92 Mo, 97 Mo/ 92 Mo, 98 Mo/ 92 Mo, 183 W/ 182 W, 184 W/ 182 W, and 186 W/ 182 W). Relative to terrestrial standards, LEU fuel pellets have variable Mo and W isotope compositions, thereby complicating the use of these elements as isotopically enriched taggants. As such, this work demonstrates that the isotope composition of any potential taggant must be well characterized in the base nuclear fuel prior to any taggant addition. Furthermore, these results suggest that Mo and W are not ideal candidates for isotopically enriched taggants.

58 GEOSCIENCES↗

Probing the thermal decomposition of plutonium (III) oxalate with IR and Raman spectroscopy, X-ray diffraction, and electron microscopy

The thermal decomposition of Pu(III) oxalate was analyzed by Raman microspectroscopy, infrared spectroscopy, scanning electron microscopy, and powder X-ray diffraction. These data show that crystalline Pu 2 (C 2 O 4 ) 3 •9H 2 O progressively loses water and oxalate ligands as it is heated, which leads to a decrease in long-range lattice ordering, though minimal changes are observed in gross crystalline morphology. The onset of PuO 2 formation was observed between 200 - 250 °C. Thermal decomposition of oxalate ligands leads to the formation of CO 2 and plutonium oxalate-carbonate moieties, which had not been observed in previously published thermogravimetric measurements of Pu(III) oxalate. Formation of plutonium oxalate-carbonate moieties is believed to be associated with a change in the plutonium oxidation state from 3+ to 4+, which occurs prior to PuO 2 formation. The data provided herein demonstrate the rich spectroscopic nature of a rather underexplored, and technologically relevant, plutonium system. Ideally these results will further future investigations into the Pu(III) oxalate system both experimentally and computationally.

36 MATERIALS SCIENCE↗

Optical vibrational spectroscopic signatures related to U 3 O 8 production processes

Uranium ore concentrates are materials found early within the nuclear fuel cycle and contain high concentrations of uranium in an easily transported form, making the concentrates a likely target for illegal diversion. These concentrates are typically converted to U 3 O 8 for further processing and, therefore, may lose specific physicochemical characteristics in determining the materials’ source and processing history. In this work, we explore the Raman spectra of eight oxide samples produced from various uranium ore concentrates and processing pathways to examine the presence of spectroscopic signatures relating to each sample's process history. Samples produced from amine extraction and dialkylphosphoric acid extraction processes show unique characteristics due to high concentrations of α-UO 3 , whereas samples calcinated from metallic diuranates do not form pure α-U 3 O 8 because of metallic ion inclusions. Pure α-U 3 O 8 oxide samples are obtained through calcination of ammonium diuranate, ammonium uranyl carbonate, and metastudtite intermediates. The Raman spectra of these oxide samples show close agreement with pristine α-U 3 O 8 spectra. However, deviations from the pristine spectra are observed in the 300–460 cm -1 spectral range. In conclusion, these deviations are unique identifying signatures that were likely created by lasting effects from the process history. Spectral center of mass calculations indicate grouping of samples based on processing history.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Speciation mapping of the oxidation layer on aged uranium dioxide using scanning transmission x-ray spectromicroscopy

In this study, UO 2 was aged in humid air and prepared as a thin section using a focused ion beam (FIB) instrument. The specimen was measured using synchrotron radiation spectromicroscopy techniques at the Beamline 11.0.2 STXM end station of the Advanced Light Source (ALS). Non-negative matrix factorization (NMF) methods were used to identify and map three component x-ray absorption near-edge structure (XANES) spectra in the oxygen K-edge data, revealing a surface layer of U 4 O 9 with a thickness of 206 ± 21 nm, and the bulk of the sample remaining as UO 2 . Uranium N 4,5 -edge XANES spectromicroscopy supports these results. The diffusion-controlled parabolic rate constant for UO 2 oxidation to U 4 O 9 was calculated from the observed layer thickness and compared to literature values. Complementary transmission electron microscopy (TEM) was used to image the sample and identify the phases present in various regions, confirming the STXM results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗