Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ni”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

The isotopic composition of iron-group cosmic rays

Measurements are reported of the relative abundances of Mn, Fe, Co, and Ni isotopes in Galactic cosmic rays with energies of about 325 MeV per nucleon. The observed limit (Mn-54)/(Mn-53) of less than 0.25 is significantly less than the value of about 0.8-0.9 expected if Mn-54 were stable, indicating that most of the Mn-54 produced during cosmic-ray propagation in the Galaxy has undergone radioactive decay. Relative source abundances of iron and nickel isotopes, and in particular the ratio (Fe-54)/(Fe-56) = 0.046 +/- 0.020, are generally consistent with solar system values. One exception is the source ratio (Ni-60)/(Ni-58) for which an enhancement by a factor of 2.8 +/- 1.0 over the solar value is found. The isotope (Co-59) is found to make up a sizable fraction of the observed Co, indicating a time delay more than about 100,000 yr between nucleosynthesis and acceleration if this nuclide is synthesized as (Cu-59) or (Ni-59).

Leske, Richard A.↗
NASA NTRS1993

Development of nickel-metal hydride cell

National Space Development Agency of Japan (NASDA) has conducted the research and development (R&D) of battery cells for space use. A new R&D program about a Nickel-Metal Hydride (Ni-MH) cell for space use from this year, based on good results in evaluations of commercial Ni-MH cells in Tsukuba Space Center (TKSC), was started. The results of those commercial Ni-MH cell's evaluations and recent status about the development of Ni-MH cells for space use are described.

Kuwajima, Saburo↗
NASA NTRS1993

Metal abundances at z = 3.4

Echelle spectroscopy data were taken of the quasar 0000-263 on the 4m telescope at CTIO in Chile. Three nights of red and three nights of blue data were obtained (about four hours data per night). The resolution is typically 0.4 A at 5000 A (lamda/d(lamda) = 12500) and has good signal-to-noise over the wavelength range 4600 A to 8000 A. To keep the statistics manageable the data were not rebinned, although the instrument was stable enough for each night's data on the object to be co-added. Arc spectra taken between each exposure were also co-added within the nights. During profile fitting the model was convolved with a Gaussian whose width was equal to nearby arc lines, so any broadening generated by the co-adding of data will not affect the final results. Since OI and HI have the same ionization potential (13.6 eV), (O/H) is approximately (OI/HI). Unfortunately, in this data only the 1302 A OI transition is visible, and it is blended with HI in the Lyman Alpha forest. However, OI and NI coexist (the ionization potential for NI is 14.5 eV) and so the NI triplet can constrain the redshift and turbulent width of the OI. When a fit was made to the regions containing OI and NI absorption three systems were apparent with similar redshifts and velocity widths. These three systems were fitted with tied redshifts and turbulent widths, while the other lines in the region were fitted as Lyman-Alpha. The saturated Lyman-Alpha profile was then fitted with three components at the same redshifts as these observed lines, with the line widths tied. Finally, metallicity ratios for the individual lines and their totals were calculated and compared to solar values. The results for the separate clouds from low to high redshift and for the total are presented.

Cooke, Andrew↗
NASA NTRS1993

The CR (Renazzo-type) carbonaceous chondrite group and its implications

A petrologic, geochemical, and oxygen isotropic study of the CR chondrites including Renazzo, Al Rais, El Djouf 001 and the paired Acfer meteorites, EET87770 and the paired samples, MAC87320, Y790112, Y793495, and Y791498 is presented. It is concluded that the CR group is characterized by abundant large multilayered, Fe, Ni metal-rich, type I chondrules; abundant matrix and dark inclusions; unique assemblages of serpentine and chlorite-rich phyllosilicates and Ca-carbonates; Ca-carbonate rims on chondrules; abundant Fe, Ni metal with a positive Ni vs. Co trend and a solar Ni:Co ratio; and amoeboid olivine aggregates with Mn-rich and Mn-poor forsterite.

Weisberg, Michael K.↗
NASA NTRS1947

Elastic Properties in Tension and Shear of High Strength Nonferrous Metals and Stainless Steel - Effect of Previous Deformation and Heat Treatment

A resume is given of an investigation of the influence of plastic deformation and of annealing temperature on the tensile and shear elastic properties of high strength nonferrous metals and stainless steels in the form of rods and tubes. The data were obtained from earlier technical reports and notes, and from unpublished work in this investigation. There are also included data obtained from published and unpublished work performed on an independent investigation. The rod materials, namely, nickel, monel, inconel, copper, 13:2 Cr-Ni steel, and 18:8 Cr-Ni steel, were tested in tension; 18:8 Cr-Ni steel tubes were tested in shear, and nickel, monel, aluminum-monel, and Inconel tubes were tested in both tension and shear. There are first described experiments on the relationship between hysteresis and creep, as obtained with repeated cyclic stressing of annealed stainless steel specimens over a constant load range. These tests, which preceded the measurements of elastic properties, assisted in devising the loading time schedule used in such measurements. From corrected stress-set curves are derived the five proof stresses used as indices of elastic or yield strength. From corrected stress-strain curves are derived the secant modulus and its variation with stress. The relationship between the forms of the stress-set and stress-strain curves and the values of the properties derived is discussed. Curves of variation of proof stress and modulus with prior extension, as obtained with single rod specimens, consist in wavelike basic curves with superposed oscillations due to differences of rest interval and extension spacing; the effects of these differences are studied. Oscillations of proof stress and modulus are generally opposite in manner. The use of a series of tubular specimens corresponding to different amounts of prior extension of cold reduction gave curves almost devoid of oscillation since the effects of variation of rest interval and extension spacing were removed. Comparison is also obtained between the variation of the several properties, as measured in tension and in shear. The rise of proof stress with extension is studied, and the work-hardening rates of the various metals evaluated. The ratio between the tensile and shear proof stresses for the various annealed and cold-worked tubular metals is likewise calculated. The influence of annealing or tempering temperature on the proof stresses and moduli for the cold-worked metals and for air-hardened 13:2 Cr-Ni steel is investigated. An improvement of elastic strength generally is obtained, without important loss of yield strength, by annealing at suitable temperature. The variation of the proof stress and modulus of elasticity with plastic deformation or annealing temperature is explained in terms of the relative dominance of three important factors: namely, (a) internal stress, (b) lattice-expansion or work-hardening, and (c) crystal reorientation. Effective values of Poisson's ratio were computed from tensile and shear moduli obtained on tubular specimens. The variation of Poisson's ratio with plastic deformation and annealing temperature is explained in terms of the degree of anisotropy produced by changes of (a) internal stress and (b) crystal orientation.

METALS - ELASTICITY↗
NASA NTRS1993

Containerless processing of undercooled melts

The investigation focused on the control of microstructural evolution in Mn-Al, Fe-Ni, Ni-V, and Au-Pb-Sb alloys through the high undercooling levels provided by containerless processing, and provided fundamental new information on the control of nucleation. Solidification analysis was conducted by means of thermal analysis, x-ray diffraction, and metallographic characterization on samples processed in a laboratory scale drop tube system. The Mn-Al alloy system offers a useful model system with the capability of phase separation on an individual particle basis, thus permitting a more complete understanding of the operative kinetics and the key containerless processing variables. This system provided the opportunity of analyzing the nucleation rate as a function of processing conditions and allowed for the quantitative assessment of the relevant processing parameters. These factors are essential in the development of a containerless processing model which has a predictive capability. Similarly, Ni-V is a model system that was used to study duplex partitionless solidification, which is a structure possible only in high under cooling solidification processes. Nucleation kinetics for the competing bcc and fcc phases were studied to determine how this structure can develop and the conditions under which it may occur. The Fe-Ni alloy system was studied to identify microstructural transitions with controlled variations in sample size and composition during containerless solidification. This work was forwarded to develop a microstructure map which delineates regimes of structural evolution and provides a unified analysis of experimental observations. The Au-Pb-Sb system was investigated to characterize the thermodynamic properties of the undercooled liquid phase and to characterize the glass transition under a variety of processing conditions. By analyzing key containerless processing parameters in a ground based drop tube study, a carefully designed flight experiment may be planned to utilize the extended duration microgravity conditions of orbiting spacecraft.

Perepezko, J. H.↗
NASA NTRS1993

Genesis of the IIICD iron meteorites - Evidence from silicate-bearing inclusions

Our studies of the silicate-bearing inclusions in the IIICD iron meteorites Maltahohe, Carlton, and Dayton suggest that their mineralogy and mineral compositions are related to the composition of the metal in the host meteorites. An inclusion in the low-Ni Maltahohe is similar in mineralogy to those in IAB irons, which contain olivine, pyroxene, plagioclase, graphite, and troilite. With increasing Ni concentration of the metal, silicate inclusions become poorer in graphite, richer in phosphates, and the phosphate and silicate assemblages become more complex. Dayton contains pyroxene, plagioclase, SiO2, brianite, panethite, and whitlockite, without graphite. In addition, mafic silicates become more FeO-rich with increasing Ni concentration of the hosts. In contrast, silicates in IAB irons show no such correlation with host Ni concentration, nor do they have the complex mineral assemblages of Dayton. These trends in inclusion composition and mineralogy in IIICD iron meteorites have been established by reactions between the S-rich metallic magma and the silicates, but the physical setting is uncertain. Of the two processes invoked by other authors to account for groups IAB and IIICD, fractional crystallization of S-rich cores and impact generation of melt pools, we prefer core crystallization. We suggest that the solidification of the IIICD core may have been very complex, involving fractional crystallization, nucleation effects and, possibly, liquid immiscibility.

Mccoy, Timothy J.↗
NASA NTRS1994

Metallic copper in ordinary chondrites

Metallic Cu of moderately high purity (approximately 985 mg/g Cu, approximately 15 mg/g Ni) occurs in at least 66% of ordinary chondrites (OC) as heterogeneously distributed, small (typically less than or equal to 20 micrometers) rounded to irregular grains. The mean modal abundance of metallic Cu in H, L and LL chondrites is low: 1.0 to 1.4 x 10(exp -4) vol%, corresponding to only 4 - 5 % of the total Cu in OC whole rocks. In more than 75% of the metallic-Cu-bearing OC, at least some metallic Cu occurs at metallic-Fe-Ni-troilite grain boundaries. In some cases it also occurs within troilite, within metallic Fe-Ni, or at the boundaries these phases form with silicates or chromite. Ordinary chondrites that contain a relatively large number of occurrences of metallic Cu/sq mm have a tendency to have experienced moderately high degrees of shock. Shock processes can cause local melting and transportation of metallic Fe-Ni and troilte; because metallic Cu is mainly associated with these phases, it also gets redistributed during shock events. In the most common petrographic assemblage containing metallic Cu, the Cu is adjacent to small irregular troilite grains surrounded by taenite plus tetrataenite; this assemblage resembles fizzed troilite and may have formed by localized shock melting or remelting of a metal-troilite assemblage.

Rubin, Alan E.↗
NASA NTRS2000

Catalytic Decomposition of Propellant Hydrazines, N-Nitrosodimethylamine, and N-Nitrodimethylamine

Remediation of propellant hydrazine spills, waste treatment, or cleanup of water contaminated with these propellants and/or their oxidation products is a subject of great concern for safety and the environment. Current remediation technologies typically employ oxidative methods, such as chlorination or ozonation. Methylated hydrazines, in particular 1,1-dimethythydrazine (UDMH) and to some degree monomethy1hydrazine (MMH), form N-Nitrosodimethylamine (NDMA) and N-Nitrodimethylamine (DMNM) during oxidation. These compounds are highly toxic and may persist if oxidative conditions are not sufficiently harsh. Since NDMA and DMNM may also be formed from exposure of MMH or UDMH to air, a need exists for a method that will remediate hydrazine, MMH, UDMH, NDMA, and DMNM. In this work, aqueous solutions of propellant hydrazines, NDMA, and DMNM were found to degrade by catalytic reduction with nickel-aluminum (Ni-Al) alloy under basic conditions. The reaction is based upon dissolution of At from Ni-Al alloy in aqueous media to form aluminum ion and hydrogen gas; and the resultant finely divided nickel catalyzes reduction of the hydrazine, nitrosoamine, or nitroamine by the hydrogen produced. Greater than 99 percent of hydrazine, MMH, UDMH, NDMA, and DMNM in aqueous solutions were degraded under laboratory conditions when reacted with Ni-Al alloy. UDMH was identified as an intermediate reduction product of NDMA and DNNM. NDMA and UDMH were identified as intermediate reduction products of DMNM. Control experiments without nickel showed no degradation of hydrazine, MMH or UDMH, while NDMA and DMNM were reduced to UDMH. Spill pillows containing Ni-Al alloy and solid sodium hydroxide were also found effective in absorption and degradation of UDMH. The application of chemical reduction as a means to propellant hydrazines, NDMA, and DMNM spill remediation, waste treatment, and water decontamination appears highly attractive.

Greene, Ben↗
NASA NTRS2003

Temporal Evolution of Nanostructures in a Model Nickel-Base Superalloy: Experiments and Simulations

The temporal evolution of the nanostructure of a model Ni-base superalloy (Ni-5.2 at.% Al-14.2 at.% Cr) is studied experimentally employing three-dimensional atom-probe (3DAP) microscopy in conjunction with kinetic Monte Carlo (KMC) simulations at 600 C. It is demonstrated that not only can the mean compositions of individual gamma' (Ni3Al with the Li2 structure) precipitates be measured but the Ni, Al, and Cr concentration profiles within the precipitates can also be determined for precipitates with a mean radius ( ) as small as 0.85 nm. The three asymptotic tinie dependencies of the Lifshitz-Slyzov-Wagner (LSW) theory of coarsening (Ostwald ripening) are measured and found to deviate from its theoretical predictions: possible explanations for these discrepancies are discussed. At 0.25 hr. there is 3DAP microscope evidence for the presence of precipitates of another nickel-rich phase. ="Ni3Cr" (Ni3Cr(1-x)Al(x)), which exhibits short-range order (SRO) and that is metastable with respect to Ni3Al. This metastable phase is also found by KMC simulations and has the composition Ni3Cr(1-x)Al(x), which is Ni-2.91 at.% Al-21.98 at.% Cr at 16 hours. Our results demonstrate that the decomposition of gamma the primary gamma (FCC) phase results in the concurrent formation of an ordered phase and a disordered phase by 0.25 hours.

Sudbrack, Chantal K.↗
NASA NTRS1991

The Nickel(111)/Alkaline Electrolyte Interface

The electrochemical properties of Ni (111) prepared and characterized in ultra high vacuum, UHV, by surface analytical techniques have been examined in alkaline media by cyclic voltammetry using an UHV-electrochemical cell transfer system designed and built in this laboratory. Prior to the transfer, the Ni(111) surfaces were exposed to saturation coverages of CO in UHV in an attempt to protect the surface from possible contamination with other gases during the transfer. Temperature Programmed Desorption, TPD, of CO-dosed Ni (111) surfaces displaying sharp c(4x2), LEED patterns, subsequently exposed to water-saturated Ar at atmospheric pressure in an auxiliary UHV compatible chamber and finally transferred back to the main UHV chamber, yielded CO2 and water as the only detectable products. This indicates that the CO-dosed surfaces react with water and/or bicarbonate and hydroxide as the most likely products. Based on the integration of the TPD peaks, the combined amounts of H2O and CO2 were found to be on the order of a single monolayer. The reacted c(4x2)CO/Ni(111) layer seems to protect the surface from undergoing spontaneous oxidation in strongly alkaline solutions. This was evidenced by the fact that the open circuit potential observed immediately after contact with deaerated 0.1 M KOH was about 0.38 V vs. DHE, drifting slightly towards more negative values prior to initiating the voltametric scans. The average ratio of the integrated charge obtained in the first positive linear scan in the range of 0.35 to 1.5 V vs. DHE (initiated at the open circuit potential) and the first (and subsequent) linear negative scans in the same solution yielded for various independent runs a value of 3.5 +/- 0.3. Coulometric analysis of the cyclic voltammetry curves indicate that the electrochemically formed oxyhydroxide layer involves a charge equivalent to 3.2 +/- 0.4 layers of Ni metal.

Wang, Kuilong↗
NASA NTRS2005

Carbon Nanotubes/Nanofibers by Plasma Enhanced Chemical Vapour Deposition

Plasma enhanced chemical vapour deposition (PECVD) has been recently used for the production of vertically aligned carbon nanotubedfibers (CN) directly on substrates. These structures are potentially important technologically as electron field emitters (e.g. microguns, microwave amplifiers, displays), nanoelectrodes for sensors, filter media, superhydrophobic surfaces and thermal interface materials for microelectronics. A parametric study on the growth of CN grown by glow discharge dc-PECVD is presented. In this technique, a substrate containing thin film Ni catalyst is exposed to C2H2 and NH3 gases at 700 C. Without plasma, this process is essentially thermal CVD which produces curly spaghetti-like CN as seen in Fig. 1 (a). With the plasma generated by biasing the substrate at -6OOV, we observed that the CN align vertically during growth as shown in Fig. l(b), and that the magnitude of the applied substrate bias affects the degree of alignment. The thickness of the thin film Ni catalyst was found to determine the average diameter and inversely the length of the CN. The yield and density of the CN were controlled by the use of different diffusion barrier materials under the Ni catalyst. Patterned CN growth [Fig. l(c)], with la variation in CN diameter of 4.1% and 6.3% respectively, is achieved by lithographically defining the Ni thin film prior to growth. The shape of the structures could be varied from very straight nanotube-like to conical tip-like nanofibers by increasing the ratio of C2H2 in the gas flow. Due to the plasma decomposition of C2H2, amorphous carbon (a-C) is an undesirable byproduct which could coat the substrate during CN growth. Using a combination of depth profiled Auger electron spectroscopy to study the substrate and in-situ mass spectroscopy to examine gas phase neutrals and ions, the optimal conditions for a-C free growth of CN is determined.

Teo, K. B. K.↗
NASA NTRS2000

Creep Properties of NiAl-1Hf Single Crystals Re-Investigated

NiAl-1Hf single crystals have been shown to be quite strong at 1027 C, with strength levels approaching those of advanced Ni-based superalloys. Initial testing, however, indicated that the properties might not be reproducible. Study of the 1027 C creep behavior of four different NiAl-1Hf single-crystal ingots subjected to several different heat treatments indicated that strength lies in a narrow band. Thus, we concluded that the mechanical properties are reproducible. Recent investigations of the intermetallic NiAl have confirmed that minor alloying additions combined with single-crystal growth technology can produce elevated temperature strength levels approaching those of Ni-based superalloys. For example, General Electric alloy AFN 12 {Ni-48.5(at.%) Al-0.5Hf-1Ti-0.05Ga} has a creep rupture strength equivalent to Rene 80 combined with a approximately 30-percent lower density, a fourfold improvement in thermal conductivity, and the ability to form a self-protective alumina scale in aggressive environments. Although the compositions of strong NiAl single crystals are relatively simple, the microstructures are complex and vary with the heat treatment and with small ingot-toingot variations in the alloy chemistry. In addition, initial testing suggested a strong dependence between microstructure and creep strength. If these observations were true, the ability to utilize NiAl single-crystal rotating components in turbine machinery could be severely limited. To investigate the possible limitations in the creep response of high-strength NiAl single crystals, the NASA Glenn Research Center at Lewis Field initiated an in depth investigation of the effect of heat treatment on the microstructure and subsequent 1027 C creep behavior of [001]-oriented NiAl-1Hf with a nominal chemistry of Ni-47.5Al-1Hf-0.5Si. This alloy was selected since four ingots, grown over a number of years and possessing slightly different compositions, were available for study. Specimens taken from the ingots were subjected to several heat treatment schedules, examined by transmission electron microscopy, and tested in both compression and tension. An example of the microstructure found in a [001]-oriented NiAl-1Hf specimen after a solution treatment at 1317 C for 50 hr followed by air cooling is illustrated in the image on the left, where the NiAl matrix contains a uniform distribution of nanometer-scale Gphase (Ni16Hf6Si7) precipitates. Other heat treating schedules produced microstructures with nanometer-sized G-phase cubes and plates or, in an extreme case, produced a microstructure with all the G-phase converted to Heusler (Ni2AlHf) particles. The results of 1027 C creep strength and strain rate testing are illustrated which summarizes data from tensile and compressive testing of samples cut from all four NiAl-1Hf ingots and subjected to a variety of heat treatment schedules. With one exception, all the strength values lie in a narrow band that spans six orders of magnitude in strain rate. The only factor that produced results outside of this band was the heat treatment schedule that dissolved all the G-phase and replaced it with Heusler precipitates. The results portrayed in this figure lead to the important practical conclusion that the elevated-temperature creep properties of NiAl-1Hf single crystals are reproducible and are not affected by small variations in alloy chemistry from ingot to ingot or by different initial distributions of G-phase in the heat-treated alloy. The only variable in this study that produced a significant and delerious effect on mechanical strength was a post-solution heat treatment that lead to the complete disappearance of the G-phase in favor of Heusler precipitates.

Whittenberger, J. Daniel↗
NASA NTRS2007

Co/Ni Ratio Between Is Approximately 0.35 - 8.0 GeV/nucleon from the TIGER-2001 Flight

The Trans-Iron Galactic Element Recorder (TIGER) was launched in December 2001 and 2003 from McMurdo, Antarctica and was designed to observe elements ranging from 14 < Z < 40 over an extended energy range. Observations of radioactive isotopes produced during explosive nucleosynthesis such as Ni-59 that decay only through electron capture provide important constraints on the delay between nucleosynthesis and the acceleration of galactic cosmic rays (GCRs). The isotopes of Co and Ni at low energies, in particular, the observations of the Ni-59 and Co-59 from the Cosmic Ray Isotope Spectrometer (CRIS) on the Advanced Composition Explorer, indicate a significant time delay (greater than 7.6 x 10^4 yr) between GCR nucleosynthesis and acceleration. While TIGER is not able to resolve isotopes, observations of the elemental abundances of Co and Ni at high energies further constrain models for the acceleration and propagation of GCRs. The 2001 & 2003 flights of TIGER lasted a total of approx. 50 days and collected sufficient statistics to study the Co/Ni elemental ratio over a wide range in energies. We present the elemental ratio of Co/Ni in galactic cosmic rays between approx. 0.8- 5.0 GeV/nucleon and compare these results with previous measurements and models for cosmic-ray propagation.

deNolfo, G. A.↗
NASA NTRS2008

Comparing Wild 2 Particles to Chondrites and IDPS

We compare the observed composition ranges of olivine, pyroxene and Fe-Ni sulfides in Wild 2 grains, comparing these with chondritic IDPs and chondrite classes to explore whether these data suggest affinities to known hydrous materials in particular. Wild 2 olivine has an extremely wide composition range, from Fo4-100 with a pronounced frequency peak at Fo99. The composition range displayed by the low-calcium pyroxene is also very extensive, from En52 to En100, with a significant frequency peak centered at En95. These ranges are as broad or broader than those reported for any other extraterrestrial material. Wild 2 Fe-Ni sulfides mainly have compositions close to that of FeS, with less than 2 atom % Ni - to date, only two pentlandite grains have been found among the Wild-grains suggesting that this mineral is not abundant. The complete lack of compositions between FeS and pentlandite (with intermediate solid solution compositions) suggests (but does not require) that FeS and pentlandite condensed as crystalline species, i.e. did not form as amorphous phases, which later became annealed. While we have not yet observed any direct evidence of water-bearing minerals, the presence of Ni-bearing sulfides, and magnesium-dominated olivine and low-Ca pyroxene does not rule out their presence at low abundance. We do conclude that modern major and minor element compositions of chondrite matrix and IDPs are needed.

Zolensky, Michael↗
NASA NTRS2008

Formation of gamma(sup prime)-Ni3Al via the Peritectoid Reaction: gamma + beta (+ Al2O3)=gamma(sup prime)(+ Al2O3)

The activities of Al and Ni were measured using multi-cell Knudsen effusion-cell mass spectrometry (multi-cell KEMS), over the composition range 8-32 at.%Al and temperature range T=1400-1750 K in the Ni-Al-O system. These measurements establish that equilibrium solidification of gamma(sup prime)-Ni3Al-containing alloys occurs by the eutectic reaction, L (+ Al2O3)=gamma + Beta(+ Al2O3), at 1640 +/- 1 K and a liquid composition of 24.8 +/- 0.2 at.%al (at an unknown oxygen content). The {gamma + Beta (+Al2O3} phase field is stable over the temperature range 1633-1640 K, and gamma(sup prime)-Ni3Al forms via the peritectoid, gamma + Beta (+ Al2O3)=gamma(sup prime) (+ Al2O3), at 1633 +/- 1 K. This behavior is consistent with the current Ni-Al phase diagram and a new diagram is proposed. This new Ni-Al phase diagram explains a number of unusual steady-state solidification structures reported previously and provides a much simpler reaction scheme in the vicinity of the gamma(sup prime)-Ni2Al phase field.

Copeland, Evan↗
NASA NTRS2008

Formation of gamma'-Ni3Al via the Peritectoid Reaction: gamma plus beta (+Al2O3) equals gamma'(+Al2O3)

The activities of Al and Ni were measured using multi-cell Knudsen effusion-cell mass spectrometry (multi-cell KEMS), over the composition range 8 - 32 at.%Al and temperature range T = 1400 - 1750 K in the Ni-Al-O system. These measurements establish that equilibrium solidification of gamma'-Ni3Al-containing alloys occurs by the eutectic reaction, L (+ Al2O3) = gamma + beta (+ Al2O3), at 1640 plus or minus 1 K and a liquid composition of 24.8 plus or minus 0.2 at.%Al (at an unknown oxygen content). The {gamma + beta + Al2O3} phase field is stable over the temperature range 1633 - 1640 K, and gamma'-Ni3Al forms via the peritectiod, gamma + beta (+ Al2O3) = gamma'(+ Al2O3), at 1633 plus or minus 1 K. This behavior is inconsistent with the current Ni-Al phase diagram and a new diagram is proposed. This new Ni-Al phase diagram explains a number of unusual steady state solidification structures reported previously and provides a much simpler reaction scheme in the vicinity of the gamma'-Ni3Al phase field.

Copland, Evan↗
NASA NTRS2011

Oxide Scales Formed on NiTi and NiPtTi Shape Memory Alloys

Ni-49Ti and Ni-30Pt-50Ti (at.%) shape memory alloys were oxidized isothermally in air over the temperature range of 500 to 900 C. The microstructure, composition, and phase content of the scales were studied by SEM, EDS, XRD, and metallography. Extensive plan view SEM/EDS identified various features of intact or spalled scale surfaces. The outer surface of the scale was a relatively pure TiO2 rutile structure, typified by a distinct highly striated and faceted crystal morphology. Crystal size increased significantly with temperature. Spalled regions exhibited some porosity and less distinct features. More detailed information was obtained by correlation of SEM/EDS studies of 700 C/100 hr cross-sections with XRD analyses of serial or taper-polishing of plan surfaces. Overall, multiple layers exhibited graded mixtures of NiO, TiO2, NiTiO3, Ni(Ti) or Pt(Ni,Ti) metal dispersoids, Ni3Ti or Pt3Ti depletion zones, and substrate, in that order. The NiTi alloy contained a 3 at.% Fe impurity that appeared in embedded localized Fe-Ti-rich oxides, while the NiPtTi alloy contained a 2 v/o dispersion of TiC that appeared in lower layers. The oxidation kinetics of both alloys (in a previous report) indicated parabolic growth and an activation energy (250 kJ/mole) near those reported in other Ti and NiTi studies. This is generally consistent with TiO2 existing as the primary scale constituent, as described here.

Smialek, James L.↗