Plasma Liners with Jet Nozzle Controls
Explore the source record for details and available documents.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Abstract not provided
Not Available
Not Available
Not Available
Not Available
Integrated magnetic modeling and design are important to meet the requirements for (1) formation, (2) translation, and (3) compression of a field reversed configuration (FRC) for magnetized target fusion. Off-the-shelf solutions do not exist for many generic design issues. A predictive capability for time-dependent magnetic diffusion in realistically complicated geometry is essential in designing the experiment. An eddy-current code was developed and used to compute the mutual inductances between driven magnetic coils and passive magnetic shields (flux excluder plates) to calculate the self-consistent axisymmetric magnetic fields during the first two stages. The plasma in the formation stage was modeled as an immobile solid cylinder with selectable constant resistivity and magnetic flux that was free to readjust itself. It was concluded that (1) use of experimentally obtained anomalously large plasma resistivity in magnetic diffusion simulations is sufficient to predict magnetic reconnection and FRC formation, (2) comparison of predicted and experimentally observed timescales for FRC Ohmic decay shows good agreement, and (3) for the typical range of resistivities, the magnetic null radius decay rate scales linearly with resistivity. The last result can be used to predict the rate of change in magnetic flux outside of the separatrix (equal to the back-emf loop voltage), and thus estimate a minimum {theta}-coil loop voltage required to form an FRC.
No abstract prepared.
Converging plasma jets may be able to reach the regime of high energy density plasmas (HEDP). The successful application of plasma jets to magneto-inertial fusion (MIF) would heat the plasma by fusion products and should increase the plasma energy density. This paper reports the results of using the University of Wisconsin's 1-D Lagrangian, radiation-hydrodynamics, fusion code BUCKY to investigate two MIF converging plasma jet test cases originally analyzed by Samulyak et al.[Physics of Plasmas 17, 092702 (2010)]. In these cases, 15 cm or 5 cm radially thick deuterium-tritium (DT) plasma jets merge at 60 cm from the origin and converge radially onto a DT target magnetized to 2 T and of radius 5 cm. The BUCKY calculations reported here model these cases, starting from the time of initial contact of the jets and target. Compared to the one-temperature Samulyak et al. calculations, the one-temperature BUCKY results show similar behavior, except that the plasma radius remains about twice as long near maximum compression. One-temperature and two-temperature BUCKY results differ, reflecting the sensitivity of the calculations to timing and plasma parameter details, with the two-temperature case giving a more sustained compression.
Abstract not provided.
Not Available
Discrete helical modes have been experimentally observed from implosion to explosion in cylindrical, axially magnetized ultrathin foils (B z = 0.2 - 2.0 T) using visible self-emission and laser shadowgraphy. The striation angle of the helices, phi, was found to increase during the implosion and decrease during the explosion, despite the large azimuthal magnetic field (>40 T). Here, these helical striations are interpreted as discrete, non-axisymmetric eigenmodes that persist from implosion to explosion, obeying the simple relation $\phi$ = m/kR, where m, k, and R are the azimuthal mode number, axial wavenumber, and radius, respectively. Experimentally, we found that (a) there is only one, or at the most two, dominant unstable eigenmode, (b) there does not appear to be a sharp threshold on the axial magnetic field for the emergence of the non-axisymmetric helical modes, and (c) higher axial magnetic fields yield higher azimuthal modes.
In this work, we report simulation results that suggest record neutron yields above 3 x 10 14 can be achieved in laser-driven fusion on OMEGA by imploding large-outer-diameter targets (~1010μm) containing ice layers as thin as 34μm. Historically, the performance of thin and fast capsules is thought to be highly degraded by hydrodynamic instabilities. We present pulse designs that push implosion velocities above 650 km/s while maintaining enough ablative stabilization and low enough in-flight aspect ratios to survive the acceleration phase. We show these targets also possess improved stability during deceleration stemming from augmented core temperatures and low fuel convergence.
Two commercially available platinum plating solutions (Platanex III and Platanex Luna) were evaluated for the electrodeposition of platinum layers on gold hohlraums and cylindrically shaped silver-gold ingots. The successful deposition of thin Pt layers on gold hohlraums as well as thick Pt layers on silver-gold alloys will allow for the integration of atomic layer deposition templated foam inside a hohlraum. We found that when the manufacturer’s recommendations for the Pt plating solutions were used, the coatings obtained were unacceptable because of cracking, poor adhesion, or thin and powdery Pt deposits. Therefore, alternative plating parameters were investigated, and the conditions resulting in acceptable coatings are reported here.