Results for “LASERS” — Page 36

DOE OSTI2021

Role of relativistic laser intensity on isochoric heating of metal wire targets

In a recent experimental campaign, we used laser-accelerated relativistic hot electrons to ensure heating of thin titanium wire targets up to a warm dense matter (WDM) state [EPL 114, 45002 (2016)]. The WDM temperature profiles along several hundred microns of the wire were inferred by using spatially resolved X-ray emission spectroscopy looking at the Ti Kαcharacteristic lines. A maximum temperature of ~30 eV was reached. Our study extends this work by discussing the influence of the laser parameters on temperature profiles and the optimisation of WDM wire-based generation. The depth of wire heating may reach several hundreds of microns and it is proven to be strictly dependent on the laser intensity. At the same time, it is quantitatively demonstrated that the maximum WDM temperature doesn’t appear to be sensitive to the laser intensity and mainly depends on the deposited laser energy considering ranges of 6×10 18 –6×10 20 W/cm 2 and 50–200 J.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Analyzing the effect of doping concentration in split-well resonant-phonon terahertz quantum cascade lasers

The effect of doping concentration on the temperature performance of the novel split-well resonant-phonon (SWRP) terahertz quantum-cascade laser (THz QCL) scheme supporting a clean 4-level system design was analyzed using non-equilibrium Green’s functions (NEGF) calculations. Experimental research showed that increasing the doping concentration in these designs led to better results compared to the split-well direct-phonon (SWDP) design, which has a larger overlap between its active laser states and the doping profile. However, further improvement in the temperature performance was expected, which led us to assume there was an increased gain and line broadening when increasing the doping concentration despite the reduced overlap between the doped region and the active laser states. Through simulations based on NEGF calculations we were able to study the contribution of the different scattering mechanisms on the performance of these devices. We concluded that the main mechanism affecting the lasers’ temperature performance is electron-electron (e-e) scattering, which largely contributes to gain and line broadening. Interestingly, this scattering mechanism is independent of the doping location, making efforts to reduce overlap between the doped region and the active laser states less effective. Optimization of the e-e scattering thus could be reached only by fine tuning of the doping density in the devices. By uncovering the subtle relationship between doping density and e-e scattering strength, our study not only provides a comprehensive understanding of the underlying physics but also offers a strategic pathway for overcoming current limitations. This work is significant not only for its implications on specific devices but also for its potential to drive advancements in the entire THz QCL field, demonstrating the crucial role of e-e scattering in limiting temperature performance and providing essential knowledge for pushing THz QCLs to new temperature heights.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2026

Feature issue introduction: laser driven inertial confinement fusion and bridging the gaps to inertial fusion energy systems

Major fusion research milestones have been achieved using laser driven inertial confinement fusion (ICF) in recent years, and these successes have ignited tremendous enthusiasm for inertial fusion energy (IFE). However, the complexity and difficulty of obtaining fusion ignition with a laser driver in a research setting are often underappreciated, as are the gaps to high driver efficiency, high repetition rates, and laser and target durability requirements needs for IFE. On the academic side, several new research laser systems have been constructed over the past few years, enabling researchers to probe the limits of ICF physics and engineering. This feature issue highlights the challenges and capabilities of laser research and development targeted towards advancing IFE.

Physics - Plasma physics↗

DOE OSTI2024

Ground observations of a space laser for the assessment of its in-orbit performance

The wind mission Aeolus of the European Space Agency was a groundbreaking achievement for Earth observation. Between 2018 and 2023, the space-borne lidar instrument ALADIN onboard the Aeolus satellite measured atmospheric wind profiles with global coverage, which contributed to improving the accuracy of numerical weather prediction. The precision of the wind observations, however, declined over the course of the mission due to a progressive loss of the atmospheric backscatter signal. The analysis of the root cause was supported by the Pierre Auger Observatory in Argentina whose fluorescence detector registered the ultraviolet laser pulses emitted from the instrument in space, thereby offering an estimation of the laser energy at the exit of the instrument for several days in 2019, 2020, and 2021. The reconstruction of the laser beam not only allowed for an independent assessment of the Aeolus performance, but also helped to improve the accuracy in the determination of the laser beam’s ground track on single pulse level. The results presented in this paper set a precedent for the monitoring of space lasers by ground-based telescopes and open new possibilities for the calibration of cosmic-ray observatories.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2024

Ultra-intense femtosecond laser interactions with aligned nanostructures

The interaction of ultrafast laser pulses of relativistic intensity with high aspect ratio nanostructures can efficiently and volumetrically heat matter to an ultra-high-energy-density regime encountered in the center of stars and within the core of fusion capsules compressed by the world’s largest lasers. It also generates gigantic quasi-static electromagnetic fields that accelerate particles to very high energy. Here, we present an overview of the physics and applications of these dense relativistic plasmas that can be created with pulses of relatively modest energy from lasers that can operate at a high repetition rate. Recent nanowire array experiments produced near-solid density plasmas with an extreme degree of ionization (e.g., Au +72 ), converted ultrafast pulses of laser light into intense x-ray flashes with record efficiency, and accelerated ions to MeV energies, efficiently driving micro-scale fusion reactions that generate flashes of quasi-monoenergetic neutrons. These plasmas also serve as a platform for advancing the understanding of atomic processes in extreme environments and open a new pathway to laser-driven fusion energy. The irradiation of nanostructures at intensities of > 1 x 10 22 W cm –2 is predicted to lead to an extreme ultra-high energy density plasma regime characterized by terabar pressures that is virtually unexplored.

Optics↗

DOE OSTI2024

Shadow of a laser beam

Light, being massless, casts no shadow; under ordinary circumstances, photons pass right through each other unimpeded. Here, we demonstrate a laser beam acting like an object — the beam casts a shadow upon a surface when the beam is illuminated by another light source. We observe a regular shadow in the sense it can be seen by the naked eye, it follows the contours of the surface it falls on, and it follows the position and shape of the object (the laser beam). Specifically, we use a nonlinear optical process involving four atomic levels of ruby. We are able to control the intensity of a transmitted laser beam by applying another perpendicular laser beam. We experimentally measure the dependence of the contrast of the shadow on the power of the laser beam, finding a maximum of approximately 22%, similar to that of a shadow of a tree on a sunny day. We provide a theoretical model that predicts the contrast of the shadow. This work opens new possibilities for fabrication, imaging, and illumination.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

Study of Ion Generation by a ps-laser for External Injection into Electron Beam Ion Source

We investigated ion generation from Al, Ti, Cu, Nb and Ta target elements by a picosecond-laser in the range of 10 11 – 10 13 W/cm 2 power densities at the target surface. A ps-laser with 1.27 mJ maximum energy within a 8 ps pulse and repetition rate up to 400 Hz has been used to generate a laser-ablated plasma. Dependencies of ion current vs time, total charge of registered ions as well as ion kinetic energy distributions are characterized using a Faraday cup. Significant difference in ion current dynamics between first, second and following shots onto the same target spot was found for all five target elements. The total charge of ions registered by the Faraday cup increase linearly with increasing laser pulse energy and are almost independent on the target element and number of shots onto the same target spot for all five target elements studied. Target craters have been examined using a commercially available microscope (Nikon Eclipse LV150) and crater cross section areas were found to be in the range of 0.0076 – 0.0172 mm 2 within the first five shots onto the same target spot for different target elements. A linear dependence of crater cross section square on laser pulse energy has been observed for the Ta target. Ion energy distributions for all target elements have a plateau or a slight peak in the energy range of 10 - 100 eV and long low-intensity energy tail up to tens of keV.

43 PARTICLE ACCELERATORS↗

DOE OSTI2022

Pulse Strengthened and Laser Edge Sealed Vacuum Insulation Glazing

A scalable, low-cost processing strategy for glass strengthening and sealing is proposed to improve the thermal performance of insulating glass units and develop innovative window technologies. In this project, a combination of large area photonic processing, additive manufacturing, and laser encapsulation techniques is reported to realize a vacuum glazing technology to meet the cost, performance, reliability, and throughput demands. A modeling framework for evaluating the mechanical and thermal response was established to verify the structural deformation and thermal conductance. Micro-size glass frits in printing ink and a continuous-wave laser curing were employed to allow the formation of a hermetic bonding layer and led to improvement of glass edge sealing. Various sealing parameters, including laser traveling speed, spot diameter, and laser power were optimized. The water seepage and mechanical strength of the resulting glass-to-glass bonding were examined as well. These results showcase the development of a practical vacuum insulating glazing with several unique features through a combination of photonic processing, laser encapsulation, and additive manufacturing.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2024

Exploration of Rayleigh-Taylor seeding mechanisms in laser- and pulsed-power-driven inertial fusion

The ubiquitous Rayleigh-Taylor instability (RTI) has been observed in fluids and plasmas in a wide range of parameter regimes from astrophysical to laboratory plasmas. In high-energy-density (HED) laboratory plasmas, such as laser-driven inertial confinement fusion (ICF) plasmas, the RTI can have a detrimental impact on achieving fusion ignition through the generation of hydrodynamic mix. Hence, an understanding of the seeding mechanisms that produce the RTI and identifying ways to mitigate hydrodynamic mix is of critical importance. Appropriately aligned magnetic fields have been known to stabilize short-wavelength RTI. A number of numerical and experimental studies have demonstrated the benefits of using imposed magnetic fields in laser-driven ICF to achieve higher ion temeratures, higher neutron yields, and a relaxation of the ignition criteria. This work addresses seeding mechanisms in laser-driven implosions to understand critical early-stage physics that ultimately leads to substantial growth of the RTI along with mechanisms for mitigation of this growth. Surface perturbations due to machining tolerances and single-feature seeds (for example due to fill tubes) can produce substantial RTI growth in the ignition-relevant high-convergence ratio targets for laser- driven ICF implosions. RTI growth from single-feature seeding in laser-based implosions has the potential to be mitigated through appropriately aligned externally applied magnetic fields and the goal of this work has been to quantify that numerically and experimentally. Resistive-magnetohydrodynamic (MHD) simu- lations are used to study the seeding and evolution of the RTI leveraging previous support from the DOE HEDLP program. Furthermore, experimental data has been obtained and applied towards code validation of unmagnetized and magnetized evolution of single-feature seeded RTI growth.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Data-Driven Optimization of the Processing Window for 316H Components Fabricated Using Laser Powder Bed Fusion

The Advanced Materials and Manufacturing Technologies Program is focused on accelerating the development and deployment of advanced materials and components fabricated via additive manufacturing with a specific focus on laser powder bed fusion (LPBF). As an initial case study, the program has selected 316H stainless steel (SS) as an initial material around which to develop a code case development strategy. This strategy involves two parallel approaches: (1) an equivalency approach whereby round-robin testing across multiple collaborating laboratories demonstrates repeatability in processing and direct comparisons with conventional wrought 316H material and (2) a revolutionary approach to code qualification combining in situ data collection and high-fidelity modeling to capture, predict, and bound the performance of LPBF 316HSS components. As part of this campaign, this work package has initiated an extensive process optimization campaign across three laboratories, each printing variations of LPBF 316HSS using three different LPBF units (Concept Laser, EOS, and Renishaw). In FY23, ORNL has focused on unique experimental designs spanning wide ranges in energy inputs and turning knobs such as scan speed, laser power, hatch spacing, layer thickness, spot size, scan rotation, and more. On the Concept Laser M2, 72 different combinations of processing variables were investigated with duplicate samples and different powder compositions. In total, 252 samples were printed with combined in situ sensing data. A parallel design of experiments was conducted on the Renishaw AM400 with an additional 390 printed specimens for analysis. All 642 miniature specimens, each with unique features included in each print to capture geometry-related heterogeneity, were subjected to high-throughput x-ray computed tomography (XCT) analysis to enable the downselection of specific processing parameters of interest. Then, using electrical discharge machining (EDM), miniature tensile specimens were extracted for mechanical testing and microscopy investigations. From the analysis performed in FY23, it was found that powder composition drastically affects the resulting microstructure and mechanical performance of 316SS. Specifically, changing from 316L to 316HSS powder results in a wide range of grain sizes with varying degrees of preferred grain orientation, which increases as a function of energy density. It was also found that due to stored heat in thin fin–type features, large microstructural differences can be seen within one part printed with one set of processing parameters. These variations in microstructure features, including grain size, the nanoscale dislocation structure, and grain texture, will all affect the irradiation performance and high-temperature mechanical performance of LPBF 316HSS parts. Two sets of concept laser processing parameters, spanning both refined and columnar grain structures, were scaled to print larger 316H builds for campaign testing (high-temperature creep and irradiation). In addition, at least two optimized processing parameter sets were identified for the Renishaw AM400 for round-robin testing in FY24 with Argonne National Laboratory. Future work includes printing samples using identical parameters identified by partner institutions, providing material for corrosion and high-temperature mechanical testing, and continuing evaluations of heterogeneity in larger printed parts.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Data-Driven Optimization of the Processing Window for 316H Components Fabricated Using Laser Powder Bed Fusion

The Advanced Materials and Manufacturing Technologies Program is focused on accelerating the development and deployment of advanced materials and components fabricated via additive manufacturing with a specific focus on laser powder bed fusion (LPBF). As an initial case study, the program has selected 316H stainless steel (SS) as an initial material around which to develop a code case development strategy. This strategy involves two parallel approaches: (1) an equivalency approach whereby round-robin testing across multiple collaborating laboratories demonstrates repeatability in processing and direct comparisons with conventional wrought 316H material and (2) a revolutionary approach to code qualification combining in situ data collection and high-fidelity modeling to capture, predict, and bound the performance of LPBF 316HSS components. As part of this campaign, this work package has initiated an extensive process optimization campaign across three laboratories, each printing variations of LPBF 316HSS using three different LPBF units (Concept Laser, EOS, and Renishaw). In FY23, ORNL has focused on unique experimental designs spanning wide ranges in energy inputs and turning knobs such as scan speed, laser power, hatch spacing, layer thickness, spot size, scan rotation, and more. On the Concept Laser M2, 72 different combinations of processing variables were investigated with duplicate samples and different powder compositions. In total, 252 samples were printed with combined in situ sensing data. A parallel design of experiments was conducted on the Renishaw AM400 with an additional 390 printed specimens for analysis. All 642 miniature specimens, each with unique features included in each print to capture geometry-related heterogeneity, were subjected to high-throughput x-ray computed tomography (XCT) analysis to enable the downselection of specific processing parameters of interest. Then, using electrical discharge machining (EDM), miniature tensile specimens were extracted for mechanical testing and microscopy investigations. From the analysis performed in FY23, it was found that powder composition drastically affects the resulting microstructure and mechanical performance of 316SS. Specifically, changing from 316L to 316HSS powder results in a wide range of grain sizes with varying degrees of preferred grain orientation, which increases as a function of energy density. It was also found that due to stored heat in thin fin–type features, large microstructural differences can be seen within one part printed with one set of processing parameters. These variations in microstructure features, including grain size, the nanoscale dislocation structure, and grain texture, will all affect the irradiation performance and high-temperature mechanical performance of LPBF 316HSS parts. Two sets of concept laser processing parameters, spanning both refined and columnar grain structures, were scaled to print larger 316H builds for campaign testing (high-temperature creep and irradiation). In addition, at least two optimized processing parameter sets were identified for the Renishaw AM400 for round-robin testing in FY24 with Argonne National Laboratory. Future work includes printing samples using identical parameters identified by partner institutions, providing material for corrosion and high-temperature mechanical testing, and continuing evaluations of heterogeneity in larger printed parts.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Understanding spectral dependance of laser-induced damage precursors in dielectric materials (Full report_23-ERD-006)

The performance of high-energy laser systems is constrained by laser-induced damage in dielectric coatings, particularly those containing hafnium oxide (HfO 2 ). While thresholds at fundamental Nd harmonics are well studied, the spectral dependence of damage initiation—especially under dual-wavelength irradiation—remains poorly characterized. This project provides the first systematic investigation of wavelength-dependent laser damage in hafnia coatings, focusing on nanoscale precursors such as craze lines, nanobubbles, stoichiometric variations, nodules, and controlled crystallization. Coatings were fabricated via ion beam sputtering and electron-beam deposition and characterized using spectrophotometry, ellipsometry, AFM, GI-XRD, RBS, PCI absorption, and fs/ns laser damage testing. Results show that craze lines, benign under infrared light, strongly initiate damage under UV due to wavelength-selective field intensification. Substituting xenon for argon suppresses nanobubbles and improves UV thresholds by up to 32%. Oxygen modulation reveals that fully oxidized films maximize UV resistance, though at the cost of porosity and stress in multilayers. HfO 2 –SiO 2 composites resist crystallization and defects while achieving ppm-level absorption and elevated thresholds, whereas full crystallization of HfO 2 enhances LIDT by reducing defects and improving thermal transport. Collectively, these findings link photon energy, defect states, and bandgap collapse, providing a predictive framework for wavelength-dependent laser damage. The outcomes directly inform the design of durable, multi-wavelength coatings for facilities such as NIF, MEC, HAPLS, and DPAL, advancing the readiness of next-generation optics.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Demonstration of Control of Laser-Plasma Instabilities in the Laboratory Using STUD Pulses (Spike Trains of Uneven Duration and Delay)

The success of laser Driven Inertial Fusion Technology (LaDrIFT) hinges on controlling laser-plasma instabilities (LPI) for effective and non-deleterious energy coupling, together with the control of implosion hydrodynamic instabilities (IHI) for target integrity. Conventional approaches ignore LPI and focus on IHI. LPI control suggests the use of low intensities, short wavelengths, and thus the slow implosions of thinner shells, while IHI control calls for thicker shells, fast implosions and thus at higher laser intensities and ablation pressures. These contradicting requirements severely restrict LaDrIFT design space, flexibility and scalability. This program demonstrates, with theoretical designs and their preliminary experimental realizations, that STUD pulses (Spike Trains of Uneven Duration and Delay) can control LPI in high-energy-density (HED) laser-created plasmas and explore this physics for the first time with high repetition (rep) rate lasers.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Temperature Distribution Within an Ignition Kernel Initiated by a Laser-Induced Plasma

The sizes of, and temperature distributions within, ignition kernels initiated by a Q-switched neodymium-doped yttrium aluminum garnet laser-induced plasma in an unconfined lean premixed hydrogen-air upward jet flow are investigated. The experiments involved a range of jet velocities and a range of deposited laser energies at a fixed height above the exit along the axis of a burner. The growth of, and the temperature distributions within, the ignition kernels, as affected by the size and the energy distribution of the laser-induced plasma, are monitored with an infrared camera. The initial ignition kernels’ areas are larger with higher laser pulse energies and remain unchanged up to [Formula: see text] and then increase by factors of up to 3 at [Formula: see text]. The change in the kernel area caused by the jet velocities is less than 1.5%. An increase of the bulk velocity by 190% decreases the ignition kernel temperature by 6%. This reduction in the ignition kernel temperatures is because of an increase in energy losses by a factor of 2 and decreases in heat releases by 2% at [Formula: see text] and by 11% at [Formula: see text]. The present contributions are: measurements of and insights into temperature distributions and kernel development rates during the laser-induced plasma ignition process at different deposited energies and flow velocities.

Engineering↗

DOE OSTI2021

High-Peak-Power Long-Wave Infrared Lasers with CO2 Amplifiers

Long-wave infrared (LWIR) picosecond pulses with multi-terawatt peak power have recently become available for advanced high-energy physics and material research. Multi-joule pulse energy is achieved in an LWIR laser system via amplification of a microjoule seed pulse with high-pressure, mixed-isotope CO 2 amplifiers. A chirped-pulse amplification (CPA) scheme is employed in such a laser to reduce the nonlinear interaction between the optical field and the transmissive elements of the system. Presently, a research and development effort is underway towards an even higher LWIR peak power that is required, for instance, for promising particle acceleration schemes. The required boost of the peak power can be achieved by reducing the pulse duration to fractions of a picosecond. For this purpose, the possibility of reducing the gain narrowing in the laser amplifiers and post-compression techniques are being studied. Another direction in research is aimed at the increased throughput (i.e., repetition rate), efficiency, and reliability of LWIR laser systems. The transition from a traditional electric-discharge pumping to an optical pumping scheme for CO 2 amplifiers is expected to improve the robustness of high-peak-power LWIR lasers, making them suitable for broad implementation in scientific laboratory, industrial, and clinical environments.

43 PARTICLE ACCELERATORS↗

DOE OSTI2020

Remote Detection of Uranium Using Self-Focusing Intense Femtosecond Laser Pulses

Optical measurement techniques can address certain important challenges associated with nuclear safety and security. Detection of uranium over long distances presents one such challenge that is difficult to realize with traditional ionizing radiation detection, but may benefit from the use of techniques based on intense femtosecond laser pulses. When a high-power laser pulse propagates in air, it experiences collapse and confinement into filaments over an extended distance even without external focusing. In our experiments, we varied the initial pulse chirp to optimize the emission signal from the laser-produced uranium plasma at an extended distance. While the ablation efficiency of filaments formed by self-focusing is known to be significantly lower when compared to filaments produced by external focusing, we show that filaments formed by self-focusing can still generate luminous spectroscopic signatures of uranium detectable within seconds over a 10-m range. The intensity of uranium emission varies periodically with laser chirp, which is attributed to the interplay among self-focusing, defocusing, and multi-filament fragmentation along the beam propagation axis. Grouping of multi-filaments incident on target is found to be correlated with the uranium emission intensity. The results show promise towards long-range detection, advancing the diagnostics and analytical capabilities in ultrafast laser-based spectroscopy of high-Z elements.

42 ENGINEERING↗

DOE OSTI2020

Columnar-to-equiaxed transition in a laser scan for metal additive manufacturing

In laser powder bed fusion additive manufacturing (LPBFAM), different solidification conditions, e.g., thermal gradient and cooling rate, can be achieved by controlling the process parameters, such as laser power and laser speed. Tailoring the behaviour of the columnar to equiaxed transition (CET) of the printed alloy during fabrication can facilitate the production of highly customized microstructures. In this study, effective analytical solutions for both thermal conduction and solidification are employed to model solidifying melt pools. Microstructure textures and solidification conditions are evaluated for numerous combinations of laser power and laser speed under bead-on-plate conditions. This analytical-based high-throughput tool was demonstrated to select specific process parameters that lead to desired microstructures. Two selected process conditions were examined in detail by a highly parallelized microstructural solidification model to reveal both nucleation and grain growth. Both numerical solutions agree well with experiments that are performed based on bead-on-plate conditions, indicating that these numerical models aid evaluation of the nucleation parameters, providing insights for controlling CET during the LPBFAM processing.

Lang, Yuan↗

DOE OSTI2021

Opto-thermal laser detonator

An opto-thermal laser detonator uses resonantly absorptive tuned nano-material associated with secondary explosives for optical absorption and initiation by an integral laser diode. The opto-thermal laser detonator includes main explosive material; resonantly absorptive tuned nano-material; secondary explosive material, wherein the resonantly absorptive tuned nano-material and the secondary explosive material are associated to form associated material made of the resonantly absorptive tuned nano-material and the secondary explosive material; and a laser diode operatively connected to the associated material, wherein the laser diode initiates the associated material which in turn initiates the main explosive material.

Wilkins, Paul R.↗