Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Graphite modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Experimental investigation of the crashworthiness of scaled composite sailplane fuselages

The crash dynamics and energy absorption of composite sailplane fuselage segments undergoing nose-down impact were investigated. More than 10 quarter-scale structurally similar test articles, typical of high-performance sailplane designs, were tested. Fuselages segments were fabricated of combinations of fiberglass, graphite, Kevlar, and Spectra fabric materials. Quasistatic and dynamic tests were conducted. The quasistatic tests were found to replicate the strain history and failure modes observed in the dynamic tests. Failure modes of the quarter-scale model were qualitatively compared with full-scale crash evidence and quantitatively compared with current design criteria. By combining material and structural improvements, substantial increases in crashworthiness were demonstrated.

Kampf, Karl-Peter↗
NASA NTRS1992

Reaction layer formation at the graphite/copper-chromium alloy interface

Sessile drop tests were used to obtain information about copper chromium alloys that suitably wet graphite. Characterization of graphite/copper-chromium alloy interfaces subjected to elevated temperatures were conducted using scanning electron micrography, energy dispersive spectroscopy, auger electron spectroscopy, and x ray diffraction analyses. These analyses indicate that during sessile drop tests conducted at 1130 C for one hour, copper alloys containing greater than 0.98 percent chromium form continuous reaction layers of approximately 10 micron thickness. The reaction layers adhere to the graphite surface. The copper wets the reaction layer to form a contact angle of 60 degrees or less. X ray diffraction results indicate that the reaction layer is chromium carbide. The kinetics of reaction layer formation were modelled in terms of bulk diffusion mechanisms. Reaction layer thickness is controlled initially by the diffusion of Cr out of Cu alloy and later by the diffusion of C through chromium carbide.

Devincent, Sandra M.↗
NASA NTRS2001

Analysis of Ninety Degree Flexure Tests for Characterization of Composite Transverse Tensile Strength

Finite element (FE) analysis was performed on 3-point and 4-point bending test configurations of ninety degree oriented glass-epoxy and graphite-epoxy composite beams to identify deviations from beam theory predictions. Both linear and geometric non-linear analyses were performed using the ABAQUS finite element code. The 3-point and 4-point bending specimens were first modeled with two-dimensional elements. Three-dimensional finite element models were then performed for selected 4-point bending configurations to study the stress distribution across the width of the specimens and compare the results to the stresses computed from two-dimensional plane strain and plane stress analyses and the stresses from beam theory. Stresses for all configurations were analyzed at load levels corresponding to the measured transverse tensile strength of the material.

OBrien, T. Kevin↗
DOE OSTI2022

Atoms to fibers: Identifying novel processing methods in the synthesis of pitch-based carbon fibers

Understanding and optimizing the key mechanisms used in the synthesis of pitch-based carbon fibers (CFs) are challenging, because unlike polyacrylonitrile-based CFs, the feedstock for pitch-based CFs is chemically hetero- geneous, resulting in complex fabrication leading to inconsistency in the final properties. In this work, we use molecular dynamics simulations to explore the processing and chemical phase space through a framework of CF models to identify their effects on elastic performance. The results are in excellent agreement with experiments. We find that density, followed by alignment, and functionality of the molecular constituents dictate the CF mechanical properties more strongly than their size and shape. Last, we propose a previously unexplored fabrication route for high-modulus CFs. Unlike graphitization, this results in increased sp 3 fraction, achieved via generating high-density CFs. In addition, the high sp 3 fraction leads to the fabrication of CFs with isometric compressive and tensile moduli, enabling their potential applications for compressive loading.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

The Monolithic Heat Pipe Microreactor Reference Plant Model

This work introduces a reference plant model for a generic monolithic heat-pipe-cooled microreactor. The model will serve as a springboard to develop future evaluation models in the licensing process of similar microreactor designs at the U.S. Nuclear Regulatory Commission. This model has been developed with the Comprehensive Reactor Analysis Bundle and its specifications are based on open literature publications for the eVinci TM design. BlueCRAB is the U.S. Nu- clear Regulatory Commission non-light-water reactor analysis system based on the Multiphysics Object-Oriented Simulation Environment framework, which can couple the Griffin, BISON, and Sockeye applications to resolve the various physics that are essential for the safety analysis of this type of reactor system. The core specifications includes tristructural isotropic fuel, graphite monolith, graphite reflectors, and drums composed of graphite and B 4 C. No moderator or burnable poison pins are used in the design. The fuel enrichment is reduced to control excess reactivity in the core. This core design is not optimized and only serves for testing purposes, since the primary objective of this work is to exercise the multiphysics coupling for this type of reactor system. A three dimensional (3D) core heterogeneous Griffin discrete ordinates (SN) transport model allows the precise calculation of the flux distribution and pin powers. Griffin transfers the power density distribution and obtains a temperature distribution to and from BISON. The BISON model com- putes the 3D core temperature distribution and is coupled to 876 Sockeye subapplications running a heat pipe model. This 3D conduction model is coupled to the various heat pipes via heat flux boundary conditions. The model includes a small gap between the heat pipe and the monolith. Convective heat transfer boundaries with either ambient temperature or condenser temperature as heat sinks are imposed at the model boundaries. The 2D Sockeye heat pipe model uses a vapor- only methodology, which provides the needed resolution for transient calculations and allows the determination of various heat pipe limits. This approach is superior to the superconductor model traditionally used in steady-state calculations. BlueCRAB computes steady-state power and temperature distributions that serve as the initial condition for a loss-of-heat-sink transient simulation. The steady-state results show significant peaking due to the position of the control drum, but this is a characteristic of the particular design used, which is not optimized at this stage. The transient results show the reactor power slowly stabilizing towards a 3% power level after the partial loss of secondary heat removal. Several recriticalities are observed due to cooling through the secondary system but the reactor is self-stabilizing and behaves as expected.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Diffusion of cesium in oxidized and unoxidized IG-110 nuclear graphite

Time-release diffusion measurements of cesium have been conducted over the temperature range 1073 K – 1973 K on oxidized and unoxidized IG-110 graphite. Four cesium concentrations were tested to investigate the concentration dependence of the diffusion coefficient. Two levels of oxidation were tested and compared to unoxidized concentration-matched sets to explore the effects of graphite oxidation. Here, the results demonstrate that cesium diffusion coefficient in unoxidized IG-110 graphite is independent of concentration within the range 34 – 163 µg Cs/g graphite . Above this, the effective cesium diffusion coefficient changes with concentration. The diffusion coefficient was increased by a factor of 2–12 in the oxidized set with 7.8% mass loss. These results can be used to aid predictive modeling of cesium diffusion in HTGR cores.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Reaction layer formation at the graphite/copper-chromium alloy interface

Sessile drop tests were used to obtain information about copper chromium alloys that suitably wet graphite. Characterization of graphite/copper-chromium alloy interfaces subjected to elevated temperatures were conducted using scanning electron micrography, energy dispersive spectroscopy, Auger electron spectroscopy, and X-ray diffraction analyses. These analyses indicate that during sessile drop tests conducted at 1130 C for one hour, copper alloys containing greater than 0.98 percent chromium form continuous reaction layers of approximately 10 micron thickness. The reaction layers adhere to the graphite surface. The copper wets the reaction layer to form a contact angle of 60 degrees or less. X-ray diffraction results indicate that the reaction layer is chromium carbide. The kinetics of reaction layer formation were modelled in terms of bulk diffusion mechanisms. Reaction layer thickness is controlled initially by the diffusion of Cr out of Cu alloy and later by the diffusion of C through chromium carbide.

Devincent, Sandra M.↗
NASA NTRS1991

Probabilistic micromechanics for metal matrix composites

A probabilistic micromechanics-based nonlinear analysis procedure is developed to predict and quantify the variability in the properties of high temperature metal matrix composites. Monte Carlo simulation is used to model the probabilistic distributions of the constituent level properties including fiber, matrix, and interphase properties, volume and void ratios, strengths, fiber misalignment, and nonlinear empirical parameters. The procedure predicts the resultant ply properties and quantifies their statistical scatter. Graphite copper and Silicon Carbide Titanlum Aluminide (SCS-6 TI15) unidirectional plies are considered to demonstrate the predictive capabilities. The procedure is believed to have a high potential for use in material characterization and selection to precede and assist in experimental studies of new high temperature metal matrix composites.

Engelstad, S. P.↗
NASA NTRS2008

Are Fullerenes Relevant to Cosmochemistry? A New Finding

The abundances of noble gases found in primitive, carbonaceous meteorites are unexpected when compared with our Sun. Known as Q-gases (Q for some unknown carrier dubbed quintessence ), this anomaly has remained a mystery since it was discovered in 1975. Q-gases are characterized by increasing depletions with decreasing atomic number (Z) relative to solar noble gases and normalized to 132Xe (Figure 1). This Q-gas mass fractionation is unexplained, and its investigation is important to understanding the origin of the solar system. However, the subject is fraught with controversy, in part due to the complex nature of Q and in part due to claims of some researchers that cannot be reproduced by other investigators. The topic is discussed in numerous places [e.g., 1-4], with models of Q falling into two basic categories, both involving carbon entrapment of noble gases. First (Group A), there is the conservative two-dimensional view that Q-gases are adsorbed or sorbed onto a "labyrinth" of graphite or carbon grains [5-9], or they undergo active capture onto growing surfaces [6]. Second (Group B), there is the view holding to the remarkable property of carbon discovered in 1985. Carbon can curl up into closed geometries of hexagon- and pentagon-shaped carbon-ring configurations, a property ignored completely by Group A. Group B thinks of Q as a three-dimensional structure of endohedral carbon cages like fullerenes, carbon onions, or some class of carbon nanotubes [3, 4, 10]. Group B does not exclude Group A effects.

Wilson, T. L.↗
NASA NTRS2008

Fuel Cell Thermal Management Through Conductive Cooling Plates

An analysis was performed to evaluate the concept of utilizing conductive cooling plates to remove heat from a fuel cell stack, as opposed to a conventional internal cooling loop. The potential advantages of this type of cooling system are reduced stack complexity and weight and increased reliability through the reduction of the number of internal fluid seals. The conductive cooling plates would extract heat from the stack transferring it to an external coolant loop. The analysis was performed to determine the required thickness of these plates. The analysis was based on an energy balance between the thermal energy produced within the stack and the heat removal from the cooling plates. To accomplish the energy balance, the heat flow into and along the plates to the cooling fluid was modeled. Results were generated for various numbers of cells being cooled by a single cooling plate. The results provided cooling plate thickness, mass, and operating temperature of the plates. It was determined that utilizing high-conductivity pyrolitic graphite cooling plates can provide a specific cooling capacity (W/kg) equivalent to or potentially greater than a conventional internal cooling loop system.

Colozza, Anthony J.↗
NASA NTRS2010

Spitzer Observations of Dust Destruction in the Puppis A Supernova Remnant

Imaging and spectral observations of the Puppis A supernova remnant (SNR) with the Spitzer Space Telescope confirm that its IR emission is dominated by the thermal continuum emission of swept-up interstellar dust which is collisionally heated by the X-ray emitting gas of the SNR. Line emission is too weak to affect the fluxes measured in broadband observations, and is poorly correlated with the IR or X-ray emission. Modeling of spectra from regions both in the SNR and in the associated ISM show that the ubiquitous polycyclic aromatic hydrocarbons (PAHs) of the ISM are destroyed within the SNR, along with nearly 25% of the mass of graphite and silicate dust grains.

Arendt, Richard G.↗
DOE OSTI2026

Decomposition of methane diluted with inert gas in an RF discharge cell

Decomposition of methane using non-thermal plasmas is an attractive route for producing hydrogen-rich gases and valuable carbon nanomaterials. Understanding how plasma discharge modes influence methane decomposition in optimizing plasma-assisted chemical conversion remains unexplored. This study explores the coupling between the discharge structure and product selectivity in RF capacitively coupled discharges operating in methane/inert gas mixtures in the pressure range of 2–3 torr. Under our experimental conditions the discharge exhibits mode transitions from uniform to striated in Ar and Kr and from diffuse to contracted in Ar and Kr with <5% CH 4 . The discharges in He and Ne remained uniform under our operating conditions, and their mixtures with CH 4 remained diffuse. A 0-d model for Ar/CH 4 discharge established a threshold for contraction while also asserting the importance of Ar$^{*}_{\textrm{m}}$ in the dissociation and ionization processes. The highest degree of methane decomposition, >99.7% with the main products of acetylene and graphitized solid carbon was achieved in the contracted discharge mode for both Kr or Ar with ⩽5% CH 4 . We demonstrate that contraction can play a crucial role in the effective decomposition of methane with value-added products and that both the electronic and thermal properties of plasma gas are responsible for this effect.

RF plasma↗
NASA NTRS1978

An upper limit to the linear X-ray polarization of Scorpius X-1

A measurement of Sco X-1 with the graphite-crystal polarimeters on the OSO 8 satellite yields upper limits (3 sigmas) to the linear polarization of 2.7% and 4.9% at 2.6 keV and 5.2 keV, respectively. The results are discussed in terms of an accretion-disk model.

Weisskopf, M. C.↗
NASA NTRS1985

The stress distribution in pin-loaded orthotropic plates

The performance of mechanically fastened composite joints was studied. Specially, a single-bolt connector was modeled as a pin-loaded, infinite plate. The model that was developed used two dimensional, complex variable, elasticity techniques combined with a boundary collocation procedure to produce solutions for the problem. Through iteration, the boundary conditions were satisfied and the stresses in the plate were calculated. Several graphite epoxy laminates were studied. In addition, parameters such as the pin modulus, coefficient of friction, and pin-plate clearance were varied. Conclusions drawn from this study indicate: (1) the material properties (i.e., laminate configuration) of the plate alter the stress state and, for highly orthotropic materials, the contact stress deviates greatly from the cosinusoidal distribution often assumed; (2) friction plays a major role in the distribution of stresses in the plate; (3) reversing the load direction also greatly effects the stress distribution in the plate; (4) clearance (or interference) fits change the contact angle and thus the location of the peak hoop stress; and (5) a rigid pin appears to be a good assumption for typical material systems.

Klang, E. C.↗
NASA NTRS1992

Compression failure mechanisms of uni-ply composite plates with a circular cutout

The effect of circular-hole size on the failure mode of uniply graphite-epoxy composite plates is investigated experimentally and analytically for uniaxial compressive loading. The test specimens are sandwiched between polyetherimide plastic for nondestructive evaluations of the uniply failure mechanisms associated with a range of hole sizes. Finite-element modeling based on classical lamination theory is conducted for the corresponding materials and geometries to reproduce the experimental results analytically. The type of compressive failure is found to be a function of hole size, with fiber buckling/kinking at the hole being the dominant failure mechanism for hole diam/plate width ratios exceeding 0.062. The results of the finite-element analysis supported the experimental data for these failure mechanisms and for those corresponding to smaller hole sizes.

Khamseh, A. R.↗
NASA NTRS1994

Milestone 5 test report. Task 5, subtask 5.2: Tile to foam strength tests

This report summarizes work that has been performed to date on the strength of a cryotank insulation system using Rohacell foam and TUFI-coated AETB-12 ceramic tiles directly bonded to a simulated graphite-epoxy tank wall. Testing utilized a custom specimen design which consists of a long tensile specimen with eccentric loading to induce curvature similar to the curvature expected due to 'pillowing' of the tank when pressurized. A finite element model was constructed to predict the specific element strains in the test article, and to assist with design of the test specimen to meet the specific goals of curvature and laminate strain. The results indicate that the heat treated 3.25-pcf density Rohacell foam does not provide sufficient strength for the induced stresses due to curvature and stress concentration at the RTV bondline to the TUFI tile. The test was repeated using higher density non-heat treated Rohacell foam (6.9 pcf) without foam failure. The finite element model was shown to predict specimen behavior, and validation of the model was successful. It is pertinent to mention that the analyses described herein accurately predicted the failure of the heat treated foams and based on this analysis method it is expected that the untreated 3.25 pcf Rohacell foam will be successful.

Greenberg, H. S.↗
NASA NTRS2008

John F. Kennedy Space Center's Technology Development and Application 2006-2007 Report

Topics covered include: Reversible Chemochromic Hydrogen Detectors; Determining Trajectory of Triboelectrically Charged Particles, Using Discrete Element Modeling; Using Indium Tin Oxide To Mitigate Dust on Viewing Ports; High-Performance Polyimide Powder Coatings; Controlled-Release Microcapsules for Smart Coatings for Corrosion Applications; Aerocoat 7 Replacement Coatings; Photocatalytic Coatings for Exploration and Spaceport Design; New Materials for the Repair of Polyimide Electrical Wire Insulation; Commodity-Free Calibration; Novel Ice Mitigation Methods; Crack Offset Measurement With the Projected Laser Target Device; New Materials for Structural Composites and Protective Coatings; Fire Chemistry Testing of Spray-On Foam Insulation (SOFI); Using Aerogel-Based Insulation Material To Prevent Foam Loss on the Liquid-Hydrogen Intertank; Particle Ejection and Levitation Technology (PELT); Electrostatic Characterization of Lunar Dust; Numerical Analysis of Rocket Exhaust Cratering; RESOLVE Projects: Lunar Water Resource Demonstration and Regolith Volatile Characterization; Tribocharging Lunar Soil for Electrostatic Beneficiation; Numerically Modeling the Erosion of Lunar Soil by Rocket Exhaust Plumes; Trajectory Model of Lunar Dust Particles; Using Lunar Module Shadows To Scale the Effects of Rocket Exhaust Plumes; Predicting the Acoustic Environment Induced by the Launch of the Ares I Vehicle; Measuring Ultrasonic Acoustic Velocity in a Thin Sheet of Graphite Epoxy Composite; Hail Size Distribution Mapping; Launch Pad 39 Hail Monitor Array System; Autonomous Flight Safety System - Phase III; The Photogrammetry Cube; Bird Vision System; Automating Range Surveillance Through Radio Interferometry and Field Strength Mapping Techniques; Next-Generation Telemetry Workstation; GPS Metric Tracking Unit; and Space-Based Range.

Source record↗
DOE OSTI2026

Microreactor Assembly Transportation Cask Model Description for Criticality Safety Validation Basis Assessment (Rev. 3)

Criticality safety analyses are completed on a transportation cask used for microreactor assembly shipment to provide an example of model and analysis to industry for reproducing this type of study on their microreactor fuel shipment. The fuel assembly considered is based on a gas-cooled microreactor (GC-MR), which utilizes HALEU fuel in the form of TRISO particles and utilizes various design options considered in industry designs. Various versions of this GC-MR assembly were studied, with and without YH 2 moderator, providing similar conclusions. The shipment cask design is revised based on an existing ES-3100 design, developed by Y-12 for the transport of highly enriched uranium (HEU), but is enlarged to hold the GC-MR fuel assembly. Criticality safety analysis for the cask/GC-MR fuel assembly package was performed using the CSAS6 sequence of SCALE6.3.2, utilizing the ENDF/B-VII.1 based continuous energy neutron library, and the analysis strictly follows the guideline from NRC reference reports. Different scenarios, e.g. normal operation, undamaged cask with water flooded, damaged cask with optimal water moderation, have been analyzed and it could be concluded the package would always have a large margin of subcriticality even packed in an infinite array. Sensitivity and similarity analyses are also performed using the TSUNAMI sequence of SCALE6.3.2, and the similarity analysis uses all the experiments from the ICSBEP Handbook with Highly Enriched Uranium (HEU), Intermediate and Mixed Enriched Uranium (IEU) and Low Enriched Uranium (LEU) systems, together with additional ones that are sponsored by the DNCSH program, and selected IRPhEP experiments using TRISO fuel and graphite moderator. These similarity analyses indicate that the dry nominal design has no similar benchmark experiments (ck values greater than 0.8), which may become problematic if more assemblies are shipped together (or a fully loaded core is shipped) and margin to criticality is reduced. However, the cask models with flooded assemblies exhibited similarities to many experiments with c k values greater than 0.8.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗