Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fracture mechanics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Recertification of the air and methane storage vessels at the Langley 8-foot high-temperature structures tunnel

This center operates a number of sophisticated wind tunnels in order to fulfill the needs of its researchers. Compressed air, which is kept in steel storage vessels, is used to power many of these tunnels. Some of these vessels have been in use for many years, and Langley is currently recertifying these vessels to insure their continued structural integrity. One of the first facilities to be recertified under this program was the Langley 8-foot high-temperature structures tunnel. This recertification involved (1) modification, hydrotesting, and inspection of the vessels; (2) repair of all relevant defects; (3) comparison of the original design of the vessel with the current design criteria of Section 8, Division 2, of the 1974 ASME Boiler and Pressure Vessel Code; (4) fracture-mechanics, thermal, and wind-induced vibration analyses of the vessels; and (5) development of operating envelopes and a future inspection plan for the vessels. Following these modifications, analyses, and tests, the vessels were recertified for operation at full design pressure (41.4 MPa (6000 psi)) within the operating envelope developed.

Hudson, C. M.↗
NASA NTRS1976

Concepts for improving turbine disk integrity

Advanced disk structural concepts are used to improve the cyclic lives and reliability of turbine disks. Analytical studies were conducted to evaluate bore-entry disks as potential replacements for the existing first-stage turbine disks in the CF6-50 and JT8D-17 engines. Results of low-cycle fatigue, burst, fracture mechanics, and fragment energy analyses are summarized for the advanced disk designs and the existing disk designs with both conventional and advanced disk materials. Other disk concepts such as composite, laminated, link, multibore, multidisk, and spline disks were also evaluated for the CF6-50 engine.

Kaufman, A.↗
NASA NTRS1975

Investigation of lightweight designs and materials for LO2 and LH2 propellant tanks for space vehicles, phase 1

Design, analysis, and fabrication studies were performed on nonintegral (suspended) tanks using a representative space tug design. The LH2 and LO2 tank concept selection was developed. Tank geometries and support relationships were investigated using tug design propellant inertias and ullage pressures, then compared based on total tug systems effects. The tank combinations which resulted in the maximum payload were selected. Tests were conducted on samples of membrane material which was processed in a manner simulating production tank fabrication operations to determine fabrication effects on the fracture toughness of the tank material. Fracture mechanics analyses were also performed to establish a preliminary set of allowables for initial defects.

Source record↗
NASA NTRS1976

Influences of chemical and thermal environments on delay in a Ti-6Al-4V alloy

Experiments were conducted within the framework of linear fracture mechanics to study the effects of chemical and thermal environments on crack-growth retardation (delay) in mill-annealed Ti-6Al-4V alloy under elemental load spectra. Attention is focused on the influence of hold time at high load on delay in a 3.5 percent NaCl solution at room temperature. It is shown that delay is strongly affected by hold time at high load, where delay is longest if the high-load excursion occurs at high temperature and the subsequent fatigue is at room temperature, and shortest if the temperature profile is reversed. The results suggest that residual stresses ahead of the advancing crack play an important role in delay. The significance of combined load and environment (chemical and thermal) effects in terms of modeling and life prediction procedures is discussed.

Shih, T. T.↗
NASA NTRS1977

Crack border stress and displacement equations revisited

It is more or less accepted in fracture mechanics that the elastic stress and displacements very near to the tip of a plane line crack can be approximated with sufficient accuracy, for all geometries and outer boundary loading conditions, by a one-parameter representation, i.e., strictly in terms of the stress intensity factors KI and/or KII. It is shown here that this presumption which appears to be reasonable on face value, quantitatively speaking, is nevertheless unacceptable as a general proposition. The reason lies with the quite arbitrary practice of omitting the second term of the series representation for the stresses, a contribution which is independent of distance from the crack tip. It is not difficult to show by way of specific examples how such omission can lead to error of serious qualitative nature in the prediction of stress and displacement related quantities of interest.

Eftis, J.↗
NASA NTRS1976

Reliability and structural integrity

An analytic model is developed to calculate the reliability of a structure after it is inspected for cracks. The model accounts for the growth of undiscovered cracks between inspections and their effect upon the reliability after subsequent inspections. The model is based upon a differential form of Bayes' Theorem for reliability, and upon fracture mechanics for crack growth.

Davidson, J. R.↗
NASA NTRS1977

Flight inspection data and crack initiation times

Lockheed C-130 service-flight inspection data is reduced by means of fracture mechanics and statistical analysis into a form from which the probability of time to crack initiation and the distribution of initial flaw sizes for various locations on the aircraft can be determined. Crack sizes are normalized by extrapolating a growing crack backwards from its first recorded size to .03 inches (crack initiation size) yielding the time to crack initiation. In a similar fashion, the crack is grown backwards to a time equal to zero to yield an initial flaw size. In order to perform the discussed computations, crack growth constants were computed for each individual location and were analyzed statistically. Statistical distributions were fitted to times to crack initiation and to initial flaw sizes in order to describe their expected behavior. Weibull and Johnson distributions have been found to fit the data reasonably well but for a better fit convolution integrals of Poisson load distributions and Weibull strength distributions are needed.

Johnson, W. S.↗
NASA NTRS1979

Biocompatibility of surgical implants

Method of selecting biocompatible materials for surgical implants uses fracture mechanic relationships and surface energies of candidate materials in presence of blood plasma. Technique has been used to characterize 190 materials by parameters that reflect their biocompatibility.

Kaelble, D. H.↗
NASA NTRS1977

Turbine disks for improved reliability

Advanced disk structural concepts were employed to improve the cyclic lives and reliability of turbine disks. Analytical studies were conducted to evaluate bore-entry disks as potential replacements for the existing first-stage turbine disks in the CF6-50 and JT8D-17 engines. Results of low cycle fatigue, burst, fracture mechanics, and fragment energy analyses are summarized for the advanced disk designs and the existing disk designs, with both conventional and advanced disk materials. Other disk concepts such as composite, laminated, link, multibore, multidisk, and spline disks were also evaluated for the CF6-50 engine.

Kaufman, A.↗
NASA NTRS1978

Owens-Illinois liquid solar collector materials assessment

From the beginning, it was noted that the baseline drawings for the liquid solar collector exhibited a distinct weakness concerning materials specification where elastomers, plastics, and foam insulation materials were utilized. A relatively small effort by a competent design organization would alleviate this deficiency. Based on results obtained from boilout and stagnation tests on the solar simulator, it was concluded that proof testing of the collector tubes prior to use helps to predict their performance for limited service life. Fracture mechanics data are desirable for predicting extended service life and establishing a minimum proof pressure level requirement. The temperature capability of this collector system was increased as the design matured and the coating efficiency improved. This higher temperature demands the use of higher temperature materials at critical locations in the collector.

Nichols, R. L.↗
NASA NTRS1978

Measurements of mixed-mode crack surface displacements and comparison with theory

A theoretical and an experimental technique is used to determine crack surface displacements under mixed-mode conditions. Crack surface displacements proved to be quite useful in mode 1 fracture analysis in that they are directly related to strain energy release rate and stress intensity factor. It is felt that similar relationships can be developed for the mixed-mode case. A boundary-integral method was developed for application to two-dimensional fracture mechanics problems. This technique was applied to the mixed-mode problem. A laser interferometry technique, for measurement of crack surface displacements under mixed-mode conditions, is presented. The experimental measurements are reported and the results of the two approaches are compared and discussed.

Altiero, N. J., Jr.↗
NASA NTRS1978

Design, analysis, fabrication and test of the Space Shuttle solid rocket booster motor case

The motor case used in the solid propellant booster for the Space Shuttle is unique in many respects, most of which are indigenous to size and special design requirements. The evolution of the case design from initial requirements to finished product is discussed, with increased emphasis of reuse capability, special design features, fracture mechanics and corrosion control. Case fabrication history and the resulting procedure are briefly reviewed with respect to material development, processing techniques and special problem areas. Case assembly, behavior and performance during the DM-1 static firing are reviewed, with appropriate comments and conclusions.

Kapp, J. R.↗
NASA NTRS1978

Influence of hydrogen environments on crack growth in Inconel 718

The effect of hydrogen environments on sustained-load and cyclic-load crack growth in Inconel 718 was investigated using fracture-mechanics-type specimens. The sustained-load crack growth was determined to be a function of heat-treatment condition, temperature, and hydrogen pressure. The threshold stress intensity for subcritical crack growth was independent of hydrogen pressure at pressures greater than 21 MN/sq m (3000 psi). The cyclic-load crack growth rate in Inconel 718 at low and moderate stress intensity ranges increased with increasing hydrogen pressure. Decreasing the cyclic frequency from 1.0 to 0.1 Hz considerably increased the cyclic crack growth rate at 0.069 MN/sq m (10 psi) and at 68.9 MN/sq m (10,000 psi) hydrogen pressure. A series of measurements performed between 1.0 and 0.1 Hz showed that the crack growth rate increased as a complex function of the time per cycle.

Walter, R. J.↗
NASA NTRS1978

Adaptive finite element analysis based on p-convergence

The results of numerical experiments are presented in which a posteriori estimators of error in strain energy were examined on the basis of a typical problem in linear elastic fracture mechanics. Two estimators were found to give close upper and lower bounds for the strain energy error. The potential significance of this is that the same estimators may provide a suitable basis for adaptive redistribution of the degrees of freedom in finite element models.

Szabo, B. A.↗
NASA NTRS1979

Design, fabrication and spin testing of ceramic blade metal disk attachment

A ceramic turbine blade-metal disk attachment was designed for small, non man-rated turbine engine applications. The selected design consisted of a hot pressed silicon nitride blade having a skewed dovetail attachment with a compliant interlayer between the disk and the blade. Two-dimensional and three-dimensional analyses predicted that life goals could be achieved, considering both NDE limitations and crack growth rates for the ceramic material. Twenty ceramic blades were fabricated to closely-held manufacturing tolerances. New fracture mechanics data at elevated temperature are presented.

Calvert, G.↗
NASA NTRS1979

On the equivalence between semiempirical fracture analyses and R-curves

The relationship between several semiempirical fracture analyses (SEFA) and the R-curve concept of fracture mechanics is examined. The conditions for equivalence between a SEFA and an R-curve are derived. A hypothetical material is employed to study the relationship analytically. Equivalent R-curves are developed for real materials using data from the literature. For each SEFA there is an equivalent R-curve whose magnitude and shape are determined by the SEFA formulation and its empirical parameters. If the R-curve is indeed unique then the various empirical parameters cannot be constant, and vice versa. However, for one SEFA the differences are small enough that they may be within the range of normal data scatter for real materials.

Orange, T. W.↗
NASA NTRS1978

An engineering approach to the prediction of fatigue behavior of unnotched/notched fiber reinforced composite laminates

An engineering approach is proposed for predicting unnotched/notched laminate fatigue behavior from basic lamina fatigue data. The fatigue analysis procedure was used to determine the laminate property (strength/stiffness) degradation as a function of fatigue cycles in uniaxial tension and in plane shear. These properties were then introduced into the failure model for a notched laminate to obtain damage growth, residual strength, and failure mode. The approach is thus essentially a combination of the cumulative damage accumulation (akin to the Miner-Palmgren hypothesis and its derivatives) and the damage growth rate (similar to the fracture mechanics approach) philosophies. An analysis/experiment correlation appears to confirm the basic postulates of material wearout and the predictability of laminate fatigue properties from lamina fatigue data.

Kulkarni, S. V.↗
NASA NTRS1980

A relation between semiempirical fracture analyses and R-curves

The relations between several semiempirical fracture analyses (SEFA) and the R-curve concept of fracture mechanics are examined and the conditions for equivalence between a SEFA and an R-curve are derived. A hypothetical material is employed to study the relation analytically. Equivalent R-curves are developed for several real materials using data from the literature. For each SEFA there is an equivalent R-curve whose magnitude and shape are determined by the SEFA formulation and its empirical parameters. If the R-curve is indeed unique, then the various empirical parameters cannot be constant, and vice versa. However, for one SEFA the differences are small enough that they may be within the range of normal data scatter for real materials.

Orange, T. W.↗