Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLUORINATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Intercalation of Lithium in Pitch-Based Graphitized Carbon Fibers Chemically Modified by Fluorine: Soft Carbon With or Without an Oxide Surface

The effects of carbon structure and surface oxygen on the carbon's performance as the anode in lithium-ion battery were studied. Two carbon materials were used for the electrochemical tests: soft carbon made from defluorination of graphite fluoride, and the carbon precursor from which the graphite fluoride was made. In this research the precursor was graphitized carbon fiber P-100. It was first fluorinated to form CF(0.68), then defluorinated slowly at 350 to 450 C in bromoform, and finally heated in 1000 C nitrogen before exposed to room temperature air, producing disordered soft carbon having basic surface oxides. This process caused very little carbon loss. The electrochemical test involved cycles of lithium intercalation and deintercalation using C/saturated LiI-50/50 (vol %) EC and DMC/Li half cell. The cycling test had four major results. (1) The presence of a basic oxide surface may prevent solvent from entering the carbon structure and therefore prolong the carbon's cycle life for lithium intercalation-deintercalation. (2) The disordered soft carbon can store lithium through two different mechanisms. One of them is lithium intercalation. which gives the disordered carbon an electrochemical behavior similar to its more ordered graphitic precursor. The other is unknown in its chemistry, but is responsible for the high-N,oltage portion (less than 0.3V) of the charge-discharge curve. (3) Under certain conditions, the disordered carbon can store more lithium than its precursor. (4) These sample and its precursor can intercalate at 200 mA/g. and deintercalate at a rate of 2000 mA/g without significant capacity loss.

Hung, Ching-Chen↗
NASA NTRS2000

Polyimides Containing Fluorine and Phosphorus for Potential Space Applications

As part of an effort to develop low color, ultraviolet (UV) radiation and atomic oxygen resistant polyimides for potential space applications, a novel diamine containing fluorine and phosphorus was synthesized and used to prepare polyimides. The approach was to combine attributes from colorless, UV resistant polyimides and atomic oxygen (AO) resistant polymers into a single material. Preparation of colorless polyimides has focused on minimization of charge transfer complex formation by incorporation of bulky substituents and disrupting conjugation by using meta-catenated monomers. AO resistant polymer technology development has focused on placing phenylphosphine oxide groups into the backbone of aromatic polymers. However, polyimides prepared utilizing this approach thus far have all exhibited significant color. Thus in an attempt to combine these features in a polyimide a new diamine, bis(3-aminophenyl)-3,5-di(trifluoromethyl)phenylphosphine oxide (TFMDA) was synthesized and used to prepare polyimides. The polyimides were cast into films and characterized for physical and mechanical properties, optical transmission and AO and UV resistance.

Connell, John W.↗
NASA NTRS1999

Atmospheric pressure chemical ionization of fluorinated phenols in atmospheric pressure chemical ionization mass spectrometry, tandem mass spectrometry, and ion mobility spectrometry

Atmospheric pressure chemical ionization (APCI)-mass spectrometry (MS) for fluorinated phenols (C6H5-xFxOH Where x = 0-5) in nitrogen with Cl- as the reagent ion yielded product ions of M Cl- through ion associations or (M-H)- through proton abstractions. Proton abstraction was controllable by potentials on the orifice and first lens, suggesting that some proton abstraction occurs through collision induced dissociation (CID) in the interface region. This was proven using CID of adduct ions (M Cl-) with Q2 studies where adduct ions were dissociated to Cl- or proton abstracted to (M-H)-. The extent of proton abstraction depended upon ion energy and structure in order of calculated acidities: pentafluorophenol > tetrafluorophenol > trifluorophenol > difluorophenol. Little or no proton abstraction occurred for fluorophenol, phenol, or benzyl alcohol analogs. Ion mobility spectrometry was used to determine if proton abstraction reactions passed through an adduct intermediate with thermalized ions and mobility spectra for all chemicals were obtained from 25 to 200 degrees C. Proton abstraction from M Cl- was not observed at any temperature for phenol, monofluorophenol, or difluorophenol. Mobility spectra for trifluorophenol revealed the kinetic transformations to (M-H)- either from M Cl- or from M2 Cl- directly. Proton abstraction was the predominant reaction for tetra- and penta-fluorophenols. Consequently, the evidence suggests that proton abstraction occurs from an adduct ion where the reaction barrier is reduced with increasing acidity of the O-H bond in C6H5-xFxOH.

NASA Discipline Environmental Health↗
NASA NTRS2007

Fluorine-Based DRIE of Fused Silica

A process of deep reactive-ion etching (DRIE) using a fluorine-based gas mixture enhanced by induction-coupled plasma (ICP) has been demonstrated to be effective in forming high-aspect-ratio three-dimensional patterns in fused silica. The patterns are defined in part by an etch mask in the form of a thick, high-quality aluminum film. The process was developed to satisfy a need to fabricate high-aspect-ratio fused-silica resonators for vibratory microgyroscopes, and could be used to satisfy similar requirements for fabricating other fused-silica components.

Yee, Karl↗
NASA NTRS2012

Small-Scale Mechanical Characterization of Space-Exposed Fluorinated Ethylene Propylene Recovered from the Hubble Space Telescope

Multi-layer insulation panels from the Hubble Space Telescope have been recovered after 19.1 years of on-orbit service and micro-tensile experiments have been performed to characterize the effect of space exposure on the mechanical response of the outermost layer. This outer layer, 127 m thick fluorinated ethylene propylene with a 100 nm thick vapor deposited aluminum reflective coating, maintained significant tensile ductility but exhibited a degradation of strength that scales with severity of space exposure. This change in properties is attributed to damage from incident solar flux, atomic oxygen damage, and thermal cycling.

Jones, J. S.↗
NASA NTRS2015

Analysis of Fluorinated Polyimides Flown on the Materials International Space Station Experiment

This Technical Memorandum documents the results from the Materials on International Space Station Experiment (MISSE) series involving fluorinated polyimide films analyzed at NASA Marshall Space Flight Center. These films may be used in thermal control, sunshield, solar sail, solar concentrator, and other lightweight polymer film applications. Results include postflight structural integrity, visual observations, determination of atomic oxygen erosion yield, and optical property changes as compared to preflight values.

Finckenor, M. M.↗
NASA NTRS2018

Li(+)-ligand Binding Energies and the Effect of Ligand Fluorination on the Binding Energies

The Li(+)-ligand binding energies are computed for seven ligands and their perfluoro analogs using Density Functional Theory. The bonding is mostly electrostatic in origin. Thus the size of the binding energy tends to correlate with the ligand dipole moment, however, the charge-induced dipole contribution can be sufficiently large to affect the dipole-binding energy correlation. The perfluoro species are significantly less strongly bound than their parents, because the electron withdrawing power of the fluorine reduces the ligand dipole moment.

Charles W Bauschlicher↗
NASA NTRS2023

On the Origin of Fluorine-Poor Apatite in Chondrite Parent Bodies

We conducted a petrologic study of apatite within one LL chondrite, six R chondrites, and six CK chondrites. These data were combined with previously published apatite data from a broader range of chondrite meteorites to determine that chondrites host either chlorapatite or hydroxylapatite with ≤33 mol% F in the apatite X-site (unless affected by partial melting by impacts, which can cause F-enrichment of residual apatite). These data indicate that either fluorapatite was not a primary condensate from the solar nebula or that it did not survive lower temperature nebular processes and/or parent body processes. Bulk-rock Cl and F data from chondrites were used to determine that the solar system has a Cl/F ratio of 10.5 ± 1.0 (3σ). The Cl/F ratios of apatite from chondrites are broadly reflective of the solar system Cl/F value, indicating that apatite in chondrites is fluorine poor because the solar system has about an order of magnitude more Cl than F. The Cl/F ratio of the solar system was combined with known apatite-melt partitioning relationships for F and Cl to predict the range of apatite compositions that would form from a melt with a chondritic Cl/F ratio. This range of apatite compositions allowed for the development of a crude model to use apatite X-site compositions from achondrites (and chondrite melt rocks) to determine whether they derive from a volatile-depleted and/or differentiated source, albeit with important caveats that are detailed in the manuscript. This study further highlights the utility of apatite as a mineralogical tool to understand the origin of volatiles (including H 2 O) and the diversity of their associated geological processes throughout the history of our solar system, including at its nascent stage.

Francis M. McCubbin↗
NASA NTRSDate not supplied

Enhanced Far Ultra-Violet Optical Properties of Physical Vapor Deposited Aluminum Mirrors Through Fluorination

Astronomical instrumentation for measurements in the Far Ultra-Violet (FUV, 90-200 nm) typically use aluminum (Al) thin films due to their high reflectance over this wavelength range. However, the native aluminum oxide layer that forms on Al upon exposure to the atmosphere is strongly absorbing in this wavelength range, requiring that the films be protected with a dielectric that inhibits oxidation. Typically, magnesium fluoride (MgF 2 ) or lithium fluoride (LiF) coatings are used as protective layers, but each has shortcomings. For example, MgF 2 has an absorption cutoff at 115 nm reducing performance in a critical part of the FUV spectrum of observational interest. A viable option to access these lower wavelengths could be the use of the LiF overcoat as it has a lower absorption cutoff at 102.5 nm, but it is hygroscopic and thus susceptible to degradation in humid conditions. An approach to reduce the hygroscopic nature of LiF would be to implement a passivation process during the deposition of both Al+LiF coatings. Our team at GSFC has developed a new reactive Physical Vapor Deposition (rPVD) process that consists of a fluorination process with XeF 2 gas combined with our traditional PVD process. We have found that this new rPVD coating process offers a protected version of Al+LiF with a more environmentally stable and more transparent LiF layer, along with unprecedent reflectivity. The process starts with a bare optically smooth substrate that is coated with Al in an ultra-high vacuum (UHV) chamber by the conventional PVD process. Then, the bare Al mirror is immediately exposed to a reactive XeF 2 gas before and after the application of the flash PVD evaporated LiF layer. We have also been investigating the use of this rPVD coating process for potential efficiency enhancements of Si-based gratings. Since it is known that the XeF 2 vapor is a strong Si etchant, we are investigating if the native SiO 2 layer on Si is sufficient to protect the groove profile of e-beam-ruled Si gratings from degradation. We will report on the characterization of various Al+LiF witness mirror coatings (both on borosilicate and Si) performed under various deposition conditions using the XeF 2 passivation process. These tests include XPS to determine film stoichiometry and AFM/SEM to measure surface roughness and any etching on the Si substrate. We will also report on FUV reflectance and spectroscopic ellipsometry to characterize optical constants of these passivated films in the UV/Visible/NIR spectral ranges.

Engineering (General)↗
NASA NTRSDate not supplied

Enhanced Far Ultra-Violet Optical Properties of Physical Vapor Deposited Aluminum Mirrors Through Fluorination

Astronomical instrumentation for measurements in the Far Ultra-Violet (FUV, 90-200 nm) typically use aluminum (Al) thin films due to their high reflectance over this wavelength range. However, the native aluminum oxide layer that forms on Al upon exposure to the atmosphere is strongly absorbing in this wavelength range, requiring that the films be protected with a dielectric that inhibits oxidation. Typically, magnesium fluoride (MgF 2 ) or lithium fluoride (LiF) coatings are used as protective layers, but each has shortcomings. For example, MgF 2 has an absorption cutoff at 115 nm reducing performance in a critical part of the FUV spectrum of observational interest. A viable option to access these lower wavelengths could be the use of the LiF overcoat as it has a lower absorption cutoff at 102.5 nm, but it is hygroscopic and thus susceptible to degradation in humid conditions. An approach to reduce the hygroscopic nature of LiF would be to implement a passivation process during the deposition of both Al+LiF coatings. Our team at GSFC has developed a new reactive Physical Vapor Deposition (rPVD) process that consists of a fluorination process with XeF 2 gas combined with our traditional PVD process. We have found that this new rPVD coating process offers a protected version of Al+LiF with a more environmentally stable and more transparent LiF layer, along with unprecedent reflectivity. The process starts with a bare optically smooth substrate that is coated with Al in an ultra-high vacuum (UHV) chamber by the conventional PVD process. Then, the bare Al mirror is immediately exposed to a reactive XeF 2 gas before and after the application of the flash PVD evaporated LiF layer. We have also been investigating the use of this rPVD coating process for potential efficiency enhancements of Si-based gratings. Since it is known that the XeF 2 vapor is a strong Si etchant, we are investigating if the native SiO 2 layer on Si is sufficient to protect the groove profile of e-beam-ruled Si gratings from degradation. We will report on the characterization of various Al+LiF witness mirror coatings (both on borosilicate and Si) performed under various deposition conditions using the XeF 2 passivation process. These tests include XPS to determine film stoichiometry and AFM/SEM to measure surface roughness and any etching on the Si substrate. We will also report on FUV reflectance and spectroscopic ellipsometry to characterize optical constants of these passivated films in the UV/Visible/NIR spectral ranges.

Engineering (General)↗
NASA NTRSDate not supplied

Enhanced Far Ultra-Violet Optical Properties of Physical Vapor Deposited Aluminum Mirrors Through Fluorination

Astronomical instrumentation for measurements in the Far Ultra-Violet (FUV, 90-200 nm) typically use aluminum (Al) thin films due to their high reflectance over this wavelength range. However, the native aluminum oxide layer that forms on Al upon exposure to the atmosphere is strongly absorbing in this wavelength range, requiring that the films be protected with a dielectric that inhibits oxidation. Typically, magnesium fluoride (MgF 2 ) or lithium fluoride (LiF) coatings are used as protective layers, but each has shortcomings. For example, MgF 2 has an absorption cutoff at 115 nm reducing performance in a critical part of the FUV spectrum of observational interest. A viable option to access these lower wavelengths could be the use of the LiF overcoat as it has a lower absorption cutoff at 102.5 nm, but it is hygroscopic and thus susceptible to degradation in humid conditions. An approach to reduce the hygroscopic nature of LiF would be to implement a passivation process during the deposition of both Al+LiF coatings. Our team at GSFC has developed a new reactive Physical Vapor Deposition (rPVD) process that consists of a fluorination process with XeF 2 gas combined with our traditional PVD process. We have found that this new rPVD coating process offers a protected version of Al+LiF with a more environmentally stable and more transparent LiF layer, along with unprecedent reflectivity. The process starts with a bare optically smooth substrate that is coated with Al in an ultra-high vacuum (UHV) chamber by the conventional PVD process. Then, the bare Al mirror is immediately exposed to a reactive XeF 2 gas before and after the application of the flash PVD evaporated LiF layer. We have also been investigating the use of this rPVD coating process for potential efficiency enhancements of Si-based gratings. Since it is known that the XeF 2 vapor is a strong Si etchant, we are investigating if the native SiO 2 layer on Si is sufficient to protect the groove profile of e-beam-ruled Si gratings from degradation. We will report on the characterization of various Al+LiF witness mirror coatings (both on borosilicate and Si) performed under various deposition conditions using the XeF 2 passivation process. These tests include XPS to determine film stoichiometry and AFM/SEM to measure surface roughness and any etching on the Si substrate. We will also report on FUV reflectance and spectroscopic ellipsometry to characterize optical constants of these passivated films in the UV/Visible/NIR spectral ranges.

Engineering (General)↗
DOE OSTI2016

Electrochemical fluorination for processing of used nuclear fuel

A galvanic cell and methods of using the galvanic cell is described for the recovery of uranium from used nuclear fuel according to an electrofluorination process. The galvanic cell requires no input energy and can utilize relatively benign gaseous fluorinating agents. Uranium can be recovered from used nuclear fuel in the form of gaseous uranium compound such as uranium hexafluoride, which can then be converted to metallic uranium or UO.sub.2 and processed according to known methodology to form a useful product, e.g., fuel pellets for use in a commercial energy production system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2015

Low molecular weight salts combined with fluorinated solvents for electrolytes

Provided are electrochemical cells and electrolytes used to build such cells. An electrolyte includes at least one salt having a molecular weight less than about 250. Such salts allow forming electrolytes with higher salt concentrations and ensure high conductivity and ion transport in these electrolytes. The low molecular weight salt may have a concentration of at least about 0.5M and may be combined with one or more other salts, such as linear and cyclic imide salts and/or methide salts. The concentration of these additional salts may be less than that of the low molecular weight salt, in some embodiments, twice less. The additional salts may have a molecular weight greater than about 250. The electrolyte may also include one or more fluorinated solvents and may be capable of maintaining single phase solutions at between about -30.degree. C. to about 80.degree. C.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2015

Method for producing spatially patterned structures using fluorinated compounds

A method for producing a spatially patterned structure includes forming a layer of a material on at least a portion of a substructure of the spatially patterned structure, forming a barrier layer of a fluorinated material on the layer of material to provide an intermediate structure, and exposing the intermediate structure to at least one of a second material or radiation to cause at least one of a chemical change or a structural change to at least a portion of the intermediate structure. The barrier layer substantially protects the layer of the material from chemical and structural changes during the exposing. Substructures are produced according to this method.

Katz, Howard Edan↗
DOE OSTI2017

Patterning devices using fluorinated compounds

A method for producing a spatially patterned structure includes forming a layer of a material on at least a portion of a substructure of the spatially patterned structure, forming a barrier layer of a fluorinated material on the layer of material to provide an intermediate structure, and exposing the intermediate structure to at least one of a second material or radiation to cause at least one of a chemical change or a structural change to at least a portion of the intermediate structure. The barrier layer substantially protects the layer of the material from chemical and structural changes during the exposing. Substructures are produced according to this method.

Katz, Howard E.↗
DOE OSTI2021

Stable fluorinated alkylated lithium malonatoborate salts for lithium-ion battery applications

The invention is directed in a first aspect to electrolyte salt of the general formula Li+Z−, wherein Z− has the following chemical formula: wherein R1 is an alkyl group (R′) containing at least one and up to twelve carbon atoms, and R2 and R3 are independently selected from fluorine atom, hydrocarbon groups R, alkoxy groups (—OR), and ester groups —OC(O)R, wherein R2 and R3 can optionally interconnect via R functionalities to form a boron-containing ring. The invention is also directed to electrolyte compositions in which the above electrolyte salt is incorporated. The invention is further directed to lithium-ion batteries containing these electrolytes.

Sun, Xiao-Guang↗
DOE OSTI2016

Fluorine-ion conductivity of different technological forms of solid electrolytes R{sub 1–y}M{sub y}F{sub 3–y} (LaF{sub 3} Type ) (M = Ca, Sr, Ba; R Are Rare Earth Elements)

We have investigated the conductivity of some representatives of different technological forms of fluoride-conducting solid electrolytes R{sub 1–y}M{sub y}F{sub 3–y} (M = Ca, Sr, Ba; R are rare earth elements) with an LaF{sub 3} structure: single crystals, cold- and hot-pressing ceramics based on a charge prepared in different ways (mechanochemical synthesis, solid-phase synthesis, and fragmentation of single crystals), polycrystalline alloys, etc. It is shown (by impedance spectroscopy), that different technological forms of identical chemical composition (R, M, y) exhibit different electrical characteristics. The maximum conductivity is observed for the single-crystal form of R{sub 1–y}M{sub y}F{sub 3–y} tysonite phases, which provides (in contrast to other technological forms) the formation of true volume ion-conducting characteristics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗