SEARCH · Engineering Papers

Results for “FAILURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

All sources NASA NTRS DOE OSTI

NASA NTRS1987

The effect of resin toughness and modulus on compressive failure modes of quasi-isotropic graphite/epoxy laminates

Compressive failure mechanisms in quasi-isotropic graphite/epoxy laminates were characterized for both unnotched and notched specimens and also following damage by impact. Two types of fibers (Thornel 300 and 700) and four resin systems (Narmco 5208, American Cyanamid BP907, and Union Carbide 4901/MDA and 4901/mPDA) were studied. For all material combinations, failure of unnotched specimens was initiated by kinking of fibers in the 0-degree plies. A major difference was observed, however, in the mode of failure propagation after the 0-degree ply failure. The strength of quasi-isotropic laminates in general increased with increasing resin tensile modulus. The laminates made with Thornel 700 fibers exhibited slightly lower compressive strengths than did the laminates made with Thornel 300 fibers. The notch sensitivity as measured by the hole strength was lowest for the BP907 resin and highest for the 5208 resin. For the materials studied, however, the type of fiber had no effect on the notch sensitivity.

Hahn, H. Thomas↗

NASA NTRS1987

A systems engineering approach to automated failure cause diagnosis in space power systems

Automatic failure-cause diagnosis is a key element in autonomous operation of space power systems such as Space Station's. A rule-based diagnostic system has been developed for determining the cause of degraded performance. The knowledge required for such diagnosis is elicited from the system engineering process by using traditional failure analysis techniques. Symptoms, failures, causes, and detector information are represented with structured data; and diagnostic procedural knowledge is represented with rules. Detected symptoms instantiate failure modes and possible causes consistent with currently held beliefs about the likelihood of the cause. A diagnosis concludes with an explanation of the observed symptoms in terms of a chain of possible causes and subcauses.

Dolce, James L.↗

NASA NTRS1987

Efficient 3-D finite element failure analysis of compression loaded angle-ply plates with holes

Finite element stress analysis and the tensor polynomial failure criterion predict that failure always initiates at the interface between layers on the hole edge for notched angle-ply laminates loaded in compression. The angular location of initial failure is a function of the fiber orientation in the laminate. The dominant stress components initiating failure are shear. It is shown that approximate symmetry can be used to reduce the computer resources required for the case of unaxial loading.

Burns, S. W.↗

NASA NTRS1988

A micrographic study of bending failure in five thermoplastic-carbon fibre composite laminates

The local deformation and failure sequences of five thermoplastic matrix composites were microscopically observed while bending the samples in a small fixture attached to a microscope stage. The thermoplastics are polycarbonate, polysulfane, polyphenylsulfide, polyethersulfane, and polyetheretherketone. Comparison was made to an epoxy matrix composite, 5208/T-300. Laminates tested are (0/90) sub 2S, with outer ply fibers parallel to the beam axis. Four point bending was used at a typical span-to-thickness ratio of 39:1. It was found that all of the thermoplastic composites failed by abrupt longitudinal compression buckling of the outer ply. Very little precursory damage was observed. Micrographs reveal typical fiber kinking associated with longitudinal compression failure. Curved fracture surfaces on the fibers suggest they failed in bending rather than direct compression. Delamination was suppressed in the thermoplastic composites, and the delamination that did occur was found to be the result of compression buckling, rather than vice-versa. Microbuckling also caused other subsequent damage such as ply splitting, transverse ply shear failure, fiber tensile failure, and transverse ply cracking.

Yurgartis, S. W.↗

NASA NTRS1985

Mechanisms of thermal barrier coating degradation and failure

The objectives and initial results of a Thermal Barrier Coating (TBC) Life Prediction Model Development Program are described. The goals of this program are to: identify and understand TBC failure modes; generate quantitative TBC life data; and develop and verify a TBC life prediction model. The coating being studied is a two layer thermal barrier system incorporating a nominal ten mil outer layer of seven percent yttria partially stabilized zirconia plasma deposited over an inner layer of highly oxidation resistant low pressure plasma sprayed NiCrAlY bond coating. This coating currently is in flight service on turbine vane platforms in the JT-9D and PW2037 engines and is bill-of- material on turbine vane airfoils in the advanced PW4000 and IAE V2500 engines. Effort currently is in progress on the first task, which involves the identification and understanding of TBC failures. Five modes of coating damage were considered: thermomechanical ceramic failure; oxidative bond coat failure; hot corrosion; foreign object damage (FOD); and erosion.

Demasi, J. T.↗

NASA NTRS1989

A detailed investigation of the micromechanisms of compressive failure in open hole composite laminates

Micromechanisms responsible for compressive failure in open-hole composite laminates were investigated. Specimens containing circular center holes were loaded in compression to failure at a slow rate, and the surface damage development during loading was monitored. Several coupon compression tests were interrupted prior to catastrophic failure to allow for the assessment of fiber shear crippling and/or fiber microbuckling by NDE techniques. From these sectioning studies, the extent and mode of failure were determined, and a three-dimensional schematic of the shear crippling zone was developed. Results show that the majority of the damage in compression-loaded open-hole composite laminates is shear crippled or microbuckled 0-deg fibers; in many cases, however, the shear crippling damage within the 0-deg plies produced shear strains and damage in the adjacent off-axis plies.

Guynn, E. Gail↗

NASA NTRS1989

Failure of a laminated composite under tension-compression fatigue loading

The fatigue behavior of composite laminates under tension-compression loading is analyzed and compared with behavior under tension-tension and compression-compression loading. It is shown that for meaningful fatigue conditions, the tension-compression case is the dominant one. Both tension and compression failure modes can occur under the reversed loading, and failure is dependent on the specific lay-up of the laminate and the difference between the tensile static strength and the absolute value of the compressive static strength. The use of a fatigue failure envelope for determining the fatigue life and mode of failure is proposed and demonstrated.

Rotem, A.↗

NASA NTRS1990

Delamination failure in a unidirectional curved composite laminate

Delamination failure in a unidirectional curved composite laminate was investigated. The curved laminate failed unstably by delaminations developing around the curved region of the laminate at different depths through the thickness until virtually all bending stiffness was lost. Delamination was assumed to initiate at the location of the highest radial stress in the curved region. A closed form curved beam elasticity solution and a 2-D finite element analysis (FEA) were conducted to determine this location. The variation in the strain energy release rate, G, with delamination growth was then determined using the FEA. A strength-based failure criteria adequately predicted the interlaminar tension failure which caused initial delamination onset. Using the G analysis the delamination was predicted to extend into the arm and leg of the laminate, predominantly in mode I. As the initial delamination grew arould the curved region, the maximum radial stress in the newly formed inner sublaminate increased to a level sufficient to cause a new delamination to initiate in the sublaminate with no increase in applied load. This failure progression was observed experimentally.

Martin, Roderick H.↗

NASA NTRS1990

Failure analysis and modeling of a multicomputer system

This thesis describes the results of an extensive measurement-based analysis of real error data collected from a 7-machine DEC VaxCluster multicomputer system. In addition to evaluating basic system error and failure characteristics, we develop reward models to analyze the impact of failures and errors on the system. The results show that, although 98 percent of errors in the shared resources recover, they result in 48 percent of all system failures. The analysis of rewards shows that the expected reward rate for the VaxCluster decreases to 0.5 in 100 days for a 3 out of 7 model, which is well over a 100 times that for a 7-out-of-7 model. A comparison of the reward rates for a range of k-out-of-n models indicates that the maximum increase in reward rate (0.25) occurs in going from the 6-out-of-7 model to the 5-out-of-7 model. The analysis also shows that software errors have the lowest reward (0.2 vs. 0.91 for network errors). The large loss in reward rate for software errors is due to the fact that a large proportion (94 percent) of software errors lead to failure. In comparison, the high reward rate for network errors is due to fast recovery from a majority of these errors (median recovery duration is 0 seconds).

Subramani, Sujatha Srinivasan↗

NASA NTRS1991

A failure management prototype: DR/Rx

This failure management prototype performs failure diagnosis and recovery management of hierarchical, distributed systems. The prototype, which evolved from a series of previous prototypes following a spiral model for development, focuses on two functions: (1) the diagnostic reasoner (DR) performs integrated failure diagnosis in distributed systems; and (2) the recovery expert (Rx) develops plans to recover from the failure. Issues related to expert system prototype design and the previous history of this prototype are discussed. The architecture of the current prototype is described in terms of the knowledge representation and functionality of its components.

Hammen, David G.↗

NASA NTRS1990

Empirically based analysis of failures in software systems

An empirical analysis of software-system failures is used to study several specific issues in software testing, reliability analysis, and reuse. Failure data from a large software manufacturer and a NASA production environment were collected and analyzed. The systems ranged in size from 30,000 to over 100,000 lines. The results show that (1) the first 15 percent of the test cases detected 67 percent of the high-severity failures and 50 percent of all failures; (2) multiple fault-detection and testing phases may result in a significant increase in reliability or none at all; (3) composite measures of system reliability did not adequately reflect reliability at the function or component level; (4) developers were biased toward portions of systems that would be heavily tested; (5) fault-proneness of reused or modified components was 74 percent less than that of newly developed components; and (6) systems with more reused software had lower component development effort, but not lower component fault-proneness.

Selby, Richard W.↗

NASA NTRS1990

Tensile and compressive failure modes of laminated composites loaded by fatigue with different mean stress

Laminated composite materials tend to fail differently under tensile or compressive load. Under tension, the material accumulates cracks and fiber fractures, while under compression, the material delaminates and buckles. Tensile-compressive fatigue may cause either of these failure modes depending on the specific damage occurring in the laminate. This damage depends on the stress ratio of the fatigue loading. Analysis of the fatigue behavior of the composite laminate under tension-tension, compression-compression, and tension-compression had led to the development of a fatigue envelope presentation of the failure behavior. This envelope indicates the specific failure mode for any stress ratio and number of loading cycles. The construction of the fatigue envelope is based on the applied stress-cycles to failure (S-N) curves of both tensile-tensile and compressive-compressive fatigue. Test results are presented to verify the theoretical analysis.

Rotem, Assa↗

NASA NTRS1991

Turbofan engine demonstration of sensor failure detection

In the paper, the results of a full-scale engine demonstration of a sensor failure detection algorithm are presented. The algorithm detects, isolates, and accommodates sensor failures using analytical redundancy. The experimental hardware, including the F100 engine, is described. Demonstration results were obtained over a large portion of a typical flight envelope for the F100 engine. They include both subsonic and supersonic conditions at both medium and full, nonafter burning, power. Estimated accuracy, minimum detectable levels of sensor failures, and failure accommodation performance for an F100 turbofan engine control system are discussed.

Merrill, Walter C.↗

NASA NTRS1991

Postbuckling response and failure prediction of flat rectangular graphite-epoxy plates loaded in axial compression

The objectives of the study are to assess the capability of a first-order shear deformable degenerated shell finite element theory to predict the postbuckling response and failure modes of various graphite-epoxy panels loaded in axial compression. Two panels without holes and one with a hole are studied, and the resulting responses and failure modes correlated well with the experimental results. A progressive damage failure mechanism is applied in the nonlinear analysis, which proved successful in predictions of failure location, mode, and load.

Engelstad, S. P.↗

NASA NTRS1991

A failure diagnosis and recovery prototype for Space Station Freedom

NASA is investigating the use of advanced automation to enhance crew productivity for Space Station Freedom in numerous areas, one being failure management. This paper describes a prototype that diagnoses failure sources, assesses the future impacts of those failures on other Freedom entities, and generates courses of action whose intents are to recover from the failure within Freedom's operating conditions.

Marsh, Christopher A.↗

NASA NTRS1992

Failure detection and fault management techniques for flush airdata sensing systems

Methods based on chi-squared analysis are presented for detecting system and individual-port failures in the high-angle-of-attack flush airdata sensing system on the NASA F-18 High Alpha Research Vehicle. The HI-FADS hardware is introduced, and the aerodynamic model describes measured pressure in terms of dynamic pressure, angle of attack, angle of sideslip, and static pressure. Chi-squared analysis is described in the presentation of the concept for failure detection and fault management which includes nominal, iteration, and fault-management modes. A matrix of pressure orifices arranged in concentric circles on the nose of the aircraft indicate the parameters which are applied to the regression algorithms. The sensing techniques are applied to the F-18 flight data, and two examples are given of the computed angle-of-attack time histories. The failure-detection and fault-management techniques permit the matrix to be multiply redundant, and the chi-squared analysis is shown to be useful in the detection of failures.

Whitmore, Stephen A.↗

NASA NTRS1992

Delamination failure in a unidirectional curved composite laminate

Delamination failure in a unidirectional curved composite laminate was investigated. The curved laminate failed unstably by delaminations developing around the curved region of the laminate at different depths through the thickness until virtually all bending stiffness was lost. Delamination was assumed to initiate at the location of the highest radial stress in the curved region. A closed form curved beam elasticity solution and a 2D finite element analysis (FEA) were conducted to determine this location. The variation in the strain energy release rate, G, with delamination growth was then determined using the FEA. A strength-based failure criteria adequately predicted the interlaminar tension failure which caused initial delamination onset. Using the G analysis the delamination was predicted to extend into the arm and leg of the laminate, predominantly in mode I. As the initial delamination grew around the curved region, the maximum radial stress in the newly formed inner sublaminate increased to a level sufficient to cause a new delamination to initiate in the sublaminate with no increase in applied load. This failure progression was observed experimentally.

Martin, Roderick H.↗

NASA NTRS1993

Evaluating Risk Of Failure With Limited Information

Report describes probabilistic failure assessment (PFA). Developed for application to spaceflight systems for sufficient testing of hardware to ensure reliability not feasible. However, must be ascertained that critical failure modes extremely unlikely to occur during service. PFA applied to any failure mode described by quantitative models of physics and mechanics of failure phenomena, such as fatigue crack in initiation or propagation in structures, leakage of seals, wear in bearings, and erosion of arcjet thrustor cathodes.

Moore, N. R.↗