SEARCH · Engineering Papers

Results for “F”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Subsonic flight test evaluation of a performance seeking control algorithm on an F-15 airplane

The subsonic flight test evaluation phase of the NASA F-15 (powered by F 100 engines) performance seeking control program was completed for single-engine operation at part- and military-power settings. The subsonic performance seeking control algorithm optimizes the quasi-steady-state performance of the propulsion system for three modes of operation. The minimum fuel flow mode minimizes fuel consumption. The minimum thrust mode maximizes thrust at military power. Decreases in thrust-specific fuel consumption of 1 to 2 percent were measured in the minimum fuel flow mode; these fuel savings are significant, especially for supersonic cruise aircraft. Decreases of up to approximately 100 degree R in fan turbine inlet temperature were measured in the minimum temperature mode. Temperature reductions of this magnitude would more than double turbine life if inlet temperature was the only life factor. Measured thrust increases of up to approximately 15 percent in the maximum thrust mode cause substantial increases in aircraft acceleration. The system dynamics of the closed-loop algorithm operation were good. The subsonic flight phase has validated the performance seeking control technology, which can significantly benefit the next generation of fighter and transport aircraft.

Gilyard, Glenn B.↗

NASA NTRS1992

The F(N) method for the one-angle radiative transfer equation applied to plant canopies

The paper presents a semianalytical solution method, called the F(N) method, for the one-angle radiative transfer equation in slab geometry. The F(N) method is based on two integral equations specifying the intensities exiting the boundaries of the vegetation canopy; the solution is obtained through an expansion in a set of basis functions with expansion coefficients to be determined. The advantage of this method is that it avoids spatial truncation error entirely because it requires discretization only in the angular variable.

Ganapol, B. D.↗

NASA NTRS1992

Coupled numerical simulation of the external and engine inlet flows for the F-18 at large incidence

This paper presents a numerical simulation of the external and engine inlet flows for the F-18 aircraft at typical high-angle-of-attack flight conditions. Two engine inlet mass flow rates, corresponding to flight idle and maximum power, were computed. This was accomplished using a structured, overset grid technique to couple the external and internal grid systems. Reynolds-averaged Navier-Stokes solutions were obtained using an implicit, finite-differencing scheme. Results show a strong coupling of the external and engine inlet flows, especially at the maximum power setting. Increasing the mass flow rate through the inlet caused the primary vortex breakdown location to move downstream. This trend is also observed in flight tests performed on the F-18. A reversed flow region upstream of the inlet duct is visible in the faired-inlet and flight-idle computations. This flow reversal is not present in the maximum power setting computation. These large-scale changes in flow structure highlight the importance of simulating inlet conditions in high-angle-of-attack aircraft computations.

Murman, Scott M.↗

NASA NTRS1992

Numerical investigation of tail buffet on F-18 aircraft

Numerical investigation of vortex induced tail buffet is conducted on the F-18 aircraft at high angles of attack. The Reynolds-averaged Navier-Stokes equations are integrated using a time-accurate, implicit procedure. A generalized overset zonal grid scheme is used to decompose the computational space around the complete aircraft with faired-over inlet. A weak coupling between the aerodynamics and structures is assumed to compute the structural oscillation of the flexible vertical tail. Time-accurate computations of the turbulent flow around the F-18 aircraft at 30 degrees angle of attack show the surface and off-surface flowfield details, including the unsteadiness created by the vortex burst and its interaction with the vertical twin tail which causes the tail buffet. The effect of installing a LEX fence on modifying the vortex structure upstream of the tail is also examined.

Rizk, Yehia M.↗

NASA NTRS1992

Overview of supersonic laminar flow control research on the F-16XL ships 1 and 2

NASA is directing research to develop technology for a high-speed civil transport. Supersonic laminar flow control has been identified as a program element, since it offers significant drag-reduction benefits and is one of the more promising technologies for producing an economically viable aircraft design. NASA is using two prototype F-16XL aircraft to research supersonic laminar flow control. The F-16XL planform is similar to design planforms of high-speed civil transports. The planform makes the aircraft ideally suited for developing technology pertinent to high-speed transports. The supersonic laminar flow control research programs for both aircraft are described. Some general results of the ship-1 program demonstrate that significant laminar flow was obtained using laminar flow control on a highly swept wing at supersonic speeds.

Anderson, Bianca T.↗

NASA NTRS1992

Flight Testing and Simulation of an F-15 Airplane Using Throttles for Flight Control

Flight tests and simulation studies using the throttles of an F-15 airplane for emergency flight control have been conducted at the NASA Dryden Flight Research Facility. The airplane and the simulation are capable of extended up-and-away flight, using only throttles for flightpath control. Initial simulation results showed that runway landings using manual throttles only control were difficult, but possible with practice. Manual approaches flown in the airplane were much more difficult, indicating a significant discrepancy between flight and simulation. Analysis of flight data and development of improved simulation models that resolve the discrepancy are discussed. An augmented throttles-only control system that controls bank angle and flightpath with appropriate feedback parameters has also been developed, evaluated in simulations, and is planned for flight in the F-15.

Flight Testing↗

NASA NTRS1993

Actuated forebody strake controls for the F-18 high alpha research vehicle

A series of ground-based studies have been conducted to develop actuated forebody strake controls for flight test evaluations using the NASA F-18 High-Alpha Research Vehicle. The actuated forebody strake concept has been designed to provide increased levels of yaw control at high angles of attack where conventional rudders become ineffective. Results are presented from tests conducted with the flight-test strake design, including static and dynamic wind-tunnel tests, transonic wind-tunnel tests, full-scale wind-tunnel tests, pressure surveys, and flow visualization tests. Results from these studies show that a pair of conformal actuated forebody strakes applied to the F-18 HARV can provide a powerful and precise yaw control device at high angles of attack. The preparations for flight testing are described, including the fabrication of flight hardware and the development of aircraft flight control laws. The primary objectives of the flight tests are to provide flight validation of the groundbased studies and to evaluate the use of this type of control to enhance fighter aircraft maneuverability.

Murri, Daniel G.↗

NASA NTRS1993

Preliminary flight test results of a fly-by-throttle emergency flight control system on an F-15 airplane

A multi-engine aircraft, with some or all of the flight control system inoperative, may use engine thrust for control. NASA Dryden has conducted a study of the capability and techniques for this emergency flight control method for the F-15 airplane. With an augmented control system, engine thrust, along with appropriate feedback parameters, is used to control flightpath and bank angle. Extensive simulation studies have been followed by flight tests. This paper discusses the principles of throttles-only control, the F-15 airplane, the augmented system, and the flight results including landing approaches with throttles-only control to within 10 ft of the ground.

Burcham, Frank W., Jr.↗

NASA NTRS1993

Evidence of thermal metamorphism on the C, G, B, and F asteroids

Reflectance spectra (0.3 to 2.6 micrometers) of 14 C, G, B, and F asteroids and 21 carbonaceous chondrite powders are compared in detail. Only three thermally metamorphosed CM-CI chondrites that have a weak UV absorption are shown to have close counterparts among those asteroids. Reflectance spectra of heated Murchison CM2 chondrite are compared with the average C and G type asteroid spectra. Murchison heated at 600 to 1000 C exhibits a similar weak UV absorption and provides the best analog for those spectra. Comparison of UV absorption strengths between 160 C, G, B, and F asteroids and carbonaceous chondrites suggests that surface minerals of most of those asteroids are thermally metamorphosed at temperatures around 600 to 1000 C.

Hiroi, Takahiro↗

NASA NTRS1922

F-5-L Boat Seaplane : performance characteristics

Performance characteristics for the F-5-L Boat Seaplane are given. Characteristic curves for the RAF-6 airfoil and the F-5-L wings, parasite resistance and velocity data, engine and propeller characteristics, effective and maximum horsepower, and cruising performance are discussed.

Diehl, W S↗

NASA NTRS1957

Effect of Overheating on Creep-rupture Properties of S-816 Alloy at 1,500 F

The effects of overheats to temperatures of 1650, 1800, 1900, and 2000 F were evaluated in terms of the changes in creep-rupture characteristics at 1500 F of S-816 alloy under stresses within the range of rupture strengths of the alloy for 100 to 1000 hours. Overheat periods were predominantly of 2-minute duration and were applied cyclically at approximately 5- or 12-hour intervals. The possible damage from overheating was believed to include internal metal structure changes induced by exposure to the higher temperatures and loss of life by creep if stress was present during the overheats.

ALLOYS, HEAT-RESISTING↗

NASA NTRS1949

Altitude performance of AN-F-58 fuels in J35-C-3 single combustor

Three fuel blends conforming to AN-F-58 specifications were tested in order to determine the influence of boiling temperatures and aromatic content on altitude performance in single combustor of 4000-pound-thrust turbojet engine. At simulated engine conditions from an altitude of 30,000 to an altitude of 60,000 feet and 85-percent rated engine speed, the three AN-F-58 fuels showed little difference in performance.

COMBUSTION - EFFECT OF ENGINE OPERATING CONDITIONS↗

NASA NTRS1949

Altitude performance of AN-F-58 fuels in J33-A-21 single combustor

Three fuels conforming to AN-F-58 specification were investigated in order to determine the influence of boiling temperatures and aromatic content on altitude performance in single combustor of a 4600-pound-thrust turbojet engine. Combustion efficiencies of the three AN-F-58 fuels were approximately equal at each simulated engine condition for altitudes from 5,000 to 50,000 feet, 90-percent normal rated engine speed, and flight Mach numbers of 0.0 and 0.6.

FUELS - PHYSICAL PROPERTIES↗

NASA NTRS1951

Ignition-delay Characteristics in Modified Open-cup Apparatus of Several Fuels with Nitric Acid Oxidants Within Temperature Range 70 to 105 Degrees F

Fluid properties and low-temperature ignition delays were obtained for approximately 90 fuel-oxidant combinations. A red fuming nitric acid containing approximately 3 percent water and 19 percent nitrogen tetroxide froze at approximately -87 degrees F and ignited several low-viscosity fuel blends of aromatic amines in triethylamine at -76 degrees F and lower. With this acid, the following average ignition delays were obtained with a blend of 30 percent o-toluidine in triethylamine: ...

FUEL SYSTEMS - ENGINES, ROCKET↗

NASA NTRS1953

Behavior of Forged S-816 Turbine Blades in Steady-state Operation of J33-9 Turbojet Engine with Stress-rupture and Metallographic Evaluations / by F. B.garrett, C. A. Gyorgak, and J. W. Weeton

An investigation was conducted to determine the behavior of recently produced, forged S-816 turbine blades in a full-scale turbojet engine, and in particular, the scatter in performance of the alloy. The turbine blades were operated as continuously as possible at a temperature of 1500 degrees F and a centrifugal stress of 21,500 pounds per square inch. The operating lives of the turbine blades varied from 181 to 539 hours, a range of 358 hours. Stress-rupture properties of specimens cut from blade airfoils also varied considerably, as much as 1257 hours at 20,000 pounds per square inch and 1500 degrees F. Since the variability of scatter of stress-rupture data is greater than that of blade performance, the scatter is probably caused by variations in the properties of the forged blades rather than by variations caused by engine operation or installation of the blades. Metallographic examinations were made to determine possible causes of the scatter and although numerous differences in microstructures of blades were found, no consistent tendencies were observed and the findings did not permit an explanation of the scatter of blade performance. The results of the metallographic examinations and of the physical tests indirectly indicated variables in the fabricating method caused the scatter in properties.

Garrett, Floyd B↗

NASA NTRS1954

Investigation of effect of fluoride on corrosion of 2S-0 aluminum and 347 stainless steel in fuming nitric acid at 170 F

The effect of small additions of fluoride on the corrosion of 2S-0 aluminum and 347 stainless steel by fuming nitric acid at 170 degrees F has been evaluated quantitatively by the determination of the weight loss of metal specimens immersed in the acid. The ratio of metal surface area to volume of acid was approximately 7.5 inch (superscript)-1 in all cases. It was found that for acids containing no fluorides the weight loss of aluminum was approximately 1/5 that of stainless steel. Addition of 1 percent fluoride ion to the acid reduced the weight loss of both metals to practically zero even after 26 days of exposure to the acid at 170 degrees F. The minimum quantity of fluoride ion required to inhibit corrosion was found to be approximately 0.25 and 0.5 percent for aluminum and stainless steel, respectively, in white fuming nitric acid and 0.5 and 1 percent in red fuming nitric acid (18 percent nitrogen dioxide). These fluoride percentages were based on the total weight of acid. Provided the concentration of fluoride ion was sufficient to inhibit corrosion, the source of these ions was immaterial. Additional information concerning the effect of fluorides on corrosion was obtained by measuring the electrode potentials of the metals against a platinum reference electrode.

Feiler, Charles E↗

NASA NTRS1993

Preliminary Flight Results of a Fly-by-throttle Emergency Flight Control System on an F-15 Airplane

A multi-engine aircraft, with some or all of the flight control system inoperative, may use engine thrust for control. NASA Dryden has conducted a study of the capability and techniques for this emergency flight control method for the F-15 airplane. With an augmented control system, engine thrust, along with appropriate feedback parameters, is used to control flightpath and bank angle. Extensive simulation studies were followed by flight tests. The principles of throttles only control, the F-15 airplane, the augmented system, and the flight results including actual landings with throttles-only control are discussed.

Burcham, Frank W., Jr.↗

NASA NTRS1994

Design and flight test of the Propulsion Controlled Aircraft (PCA) flight control system on the NASA F-15 test aircraft

This report describes the design, development and flight testing of the Propulsion Controlled Aircraft (PCA) flight control system performed at McDonnell Douglas Aerospace (MDA), St. Louis, Missouri and at the NASA Dryden Flight Research Facility, Edwards Air Force Base, California. This research and development program was conducted by MDA and directed by NASA through the Dryden Flight Research Facility for the period beginning January 1991 and ending December 1993. A propulsion steering backup to the aircraft conventional flight control system has been developed and flight demonstrated on a NASA F-15 test aircraft. The Propulsion Controlled Aircraft (PCA) flight system utilizes collective and differential thrust changes to steer an aircraft that experiences partial or complete failure of the hydraulically actuated control surfaces. The PCA flight control research has shown that propulsion steering is a viable backup flight control mode and can assist the pilot in safe landing recovery of a fighter aircraft that has damage to or loss of the flight control surfaces. NASA, USAF and Navy evaluation test pilots stated that the F-15 PCA design provided the control necessary to land the aircraft. Moreover, the feasibility study showed that PCA technology can be directly applied to transport aircraft and provide a major improvement in the survivability of passengers and crew of controls damaged aircraft.

Wells, Edward A.↗