Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CONTACT RESISTANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Combined In-Plane and Through-the-Thickness Analysis for Failure Prediction of Bolted Composite Joints

Although two-dimensional methods provide accurate predictions of contact stresses and bolt load distribution in bolted composite joints with multiple bolts, they fail to capture the effect of thickness on the strength prediction. Typically, the plies close to the interface of laminates are expected to be the most highly loaded, due to bolt deformation, and they are usually the first to fail. This study presents an analysis method to account for the variation of stresses in the thickness direction by augmenting a two-dimensional analysis with a one-dimensional through the thickness analysis. The two-dimensional in-plane solution method based on the combined complex potential and variational formulation satisfies the equilibrium equations exactly, and satisfies the boundary conditions and constraints by minimizing the total potential. Under general loading conditions, this method addresses multiple bolt configurations without requiring symmetry conditions while accounting for the contact phenomenon and the interaction among the bolts explicitly. The through-the-thickness analysis is based on the model utilizing a beam on an elastic foundation. The bolt, represented as a short beam while accounting for bending and shear deformations, rests on springs, where the spring coefficients represent the resistance of the composite laminate to bolt deformation. The combined in-plane and through-the-thickness analysis produces the bolt/hole displacement in the thickness direction, as well as the stress state in each ply. The initial ply failure predicted by applying the average stress criterion is followed by a simple progressive failure. Application of the model is demonstrated by considering single- and double-lap joints of metal plates bolted to composite laminates.

Kradinov, V.↗
NASA NTRS2006

Experiments on the Motion of Drops on a Horizontal Solid Surface due to a Wettability Gradient

Results from experiments performed on the motion of drops of tetraethylene glycol in a wettability gradient present on a silicon surface are reported and compared with predictions from a recently developed theoretical model. The gradient in wettability was formed by exposing strips cut from a silicon wafer to decyltrichlorosiland vapors. Video images of the drops captured during the experiments were subsequently analyzed for drop size and velocity as functions of position along the gradient. In separate experiments on the same strips, the static contact angle formed by small drops was measured and used to obtain the local wettability gradient to which a drop is subjected. The velocity of the drops was found to be a strong function of position along the gradient. A quasi-steady theoretical model that balances the local hydrodynamic resistance with the local driving force generally describes the observations; possible reasons for the remaining discrepancies are discussed. It is shown that a model in which the driving force is reduced to accomodate the hysteresis effect inferred from the data is able to remove most of the discrepancy between the observed and predicted velocities.

Moumen, Nadjoua↗
NASA NTRS1991

Burst annealing of high temperature GaAs solar cells

One of the major limitations of solar cells in space power systems is their vulnerability to radiation damage. One solution to this problem is to periodically heat the cells to anneal the radiation damage. Annealing was demonstrated with silicon cells. The obstacle to annealing of GaAs cells was their susceptibility to thermal damage at the temperatures required to completely anneal the radiation damage. GaAs cells with high temperature contacts and encapsulation were developed. The cells tested are designed for concentrator use at 30 suns AMO. The circular active area is 2.5 mm in diameter for an area of 0.05 sq cm. Typical one sun AMO efficiency of these cells is over 18 percent. The cells were demonstrated to be resistant to damage after thermal excursions in excess of 600 C. This high temperature tolerance should allow these cells to survive the annealing of radiation damage. A limited set of experiments were devised to investigate the feasibility of annealing these high temperature cells. The effect of repeated cycles of electron and proton irradiation was tested. The damage mechanisms were analyzed. Limitations in annealing recovery suggested improvements in cell design for more complete recovery. These preliminary experiments also indicate the need for further study to isolate damage mechanisms. The primary objective of the experiments was to demonstrate and quantify the annealing behavior of high temperature GaAs cells. Secondary objectives were to measure the radiation degradation and to determine the effect of repeated irradiation and anneal cycles.

Brothers, P. R.↗
NASA NTRS2010

Turbopump Seal Testing at Marshall Space Flight Center

The new ARES space flight program has presented many challenges to aerospace engineers and designers. One of the areas for consideration are the seals in the turbopumps that supply cryogenic propellants to the combustion chamber in the upper stage. Heritage face seals that worked in the past might not be sufficient in the newer turbopumps with increased speeds, pressures across the seals, and loads. New seal materials, engineering designs, and analysis techniques have been developed since the early use of these heritage seals, however, rub conditions and surface degradation at the sliding contact cannot be reliably predicted. Testing is required to determine the safe operating limits and verify seal wear life over the operating range. Rocketdyne in Canoga Park California entered into a task agreement with MSFC to design, fabricate, build, test, disassemble, and inspect hardware after tests of carbon materials and wear resistant coatings. The purpose of testing would be to determine the safe operating limits, empirically iterate the design, and select the best combination of materials for face seals and mating rings. This paper summarizes the many hours and efforts of individuals and teams to get the program operating successfully and presents the test results that were obtained.

Gibson, Howard G.↗
NASA NTRS2023

Shock- and Corrosion-Resistant Bearings for Space Mechanisms

Nickel-titanium (NiTi) alloys are an emerging class of materials for rolling element bearing applications that require superior corrosion resistance and/or high load capability. Certain space mechanisms fall into one or both of those categories. Often, due to size and mass considerations, space mechanism systems are limited in torque margin and necessarily require small, precision-instrument bearings with very little frictional drag (i.e., low torque). In addition, space mechanism bearings must survive launch conditions without suffering raceway dents known as brinnelling, which would increase operating torque and reduce overall smoothness. Consequently, a bearing material or design that reduces or eliminates brinnelling under high contact stress conditions would represent a beneficial technology advancement. One specific alloy, nickel-titanium-hafnium (NiTi-Hf), under development for several years at the NASA Glenn Research Center as a bearing material, has the potential to mitigate concerns about brinnelling under extreme load conditions due to its unusually high elastic strain capability. In the present work, a sample of small precision bearings produced with three different ball materials (steel, ceramic, and NiTi-Hf) is subjected to a range of load conditions sufficient to dent the races. The dent depth as a function of load is compared and demonstrates that NiTi-Hf has the potential to increase bearing load capacity from the perspective of brinnelling under severe load conditions; additional testing of full NiTi-Hf bearings demonstrates corrosion resistance superior to that of 440C bearings.

Bearings↗
NASA NTRS1980

The adhesion, friction, and wear of binary alloys in contact with single-crystal silicon carbide

Sliding friction experiments were conducted with various iron-base alloys (alloying elements were Ti, Cr, Ni, Rh, and W) in contact with a single-crystal silicon carbide (0001) surface in vacuum. Results indicate atomic size misfit and concentration of alloying elements play a dominant role in controlling adhesion, friction, and wear properties of iron-base binary alloys. The controlling mechanism of the alloy properties is an intrinsic effect involving the resistance to shear fracture of cohesive bonding in the alloy. The coefficient of friction generally increases with an increase in solute concentration. The coefficient of friction increases as the solute-to-iron atomic radius ratio increases or decreases from unity. Alloys having higher solute concentration produce more transfer to silicon carbide than do alloys having low solute concentrations. The chemical activity of the alloying element is also an important parameter in controlling adhesion and friction of alloys.

Miyoshi, K.↗
NASA NTRS1986

Status of NTD Ge bolometer material and devices

The first IR Detector Technology Workshop took place at NASA Ames Research Center on July 12 and 13, 1983. The conclusions presented at that meeting are still valid. More was learned about the physics of hopping conduction at very low temperatures which will be important for bolometer design and operation at ever decreasing temperatures. Resistivity measurements were extended down to 50 mK. At such low temperatures, precise knowledge of the neutron capture cross sections sigma (sub n) of the various Ge isotopes is critical if one is to make an accurate prediction of the dopant concentrations and compensation, and therefore resistivity, that will result from a given irradiation. An empirical approach for obtaining the desired resistivity material is described and the process of conducting a set of experiments which will improve the knowledge of the effective sigma (sub n) values for a given location in a particular reactor is discussed. A wider range of NTD Ge samples is now available. Noise measurements on bolometers with ion implanted contacts show the no 1/f noise component appears down to 1 Hz and probably lower.

Haller, E. E.↗
NASA NTRS1993

Chromium and reactive element modified aluminide diffusion coatings on superalloys - Environmental testing

The high temperature performance of reactive element (RE)-doped and Cr/RE-modified aluminide diffusion coatings on commercial Ni-base alloy substrates was determined. In isothermal oxidation at 1100 C in air, RE-doped aluminide coatings on IN 713LC substrates formed a continuous slow-growing n-Al2O3 scale after 44 hrs of exposure. The coatings were protected by either an outer ridge Al2O3 scale with an inner compact Al2O3 scale rich in RE or by a continuous compact scale without any noticeable cracks or flaws. The cyclic oxidation behavior of Cr/RE-modified aluminide coatings on Rene 80 and IN 713LC alloys and of RE-doped aluminide coatings on IN 713LC alloys at 1100 C in static air was determined. Pack powder entrapment from the powder contacting (PC) process detracted significantly from the overall cyclic oxidation performance. Type I hot corrosion behavior of Cr/RE-modified aluminide coatings on Rene 80 and Mar-M247 alloy substrates at 900 C in a catalyzed 0.1 percent SO3/O3 gas mixture was determined. The modified coatings produced from the PC arrangement provided significantly better resistance to hot corrosion attack than commercial low-activity aluminide coatings produced by the above pack arrangement.

Bianco, Robert↗
NASA NTRS2007

Lithium Dinitramide as an Additive in Lithium Power Cells

Lithium dinitramide, LiN(NO2)2 has shown promise as an additive to nonaqueous electrolytes in rechargeable and non-rechargeable lithium-ion-based electrochemical power cells. Such non-aqueous electrolytes consist of lithium salts dissolved in mixtures of organic ethers, esters, carbonates, or acetals. The benefits of adding lithium dinitramide (which is also a lithium salt) include lower irreversible loss of capacity on the first charge/discharge cycle, higher cycle life, lower self-discharge, greater flexibility in selection of electrolyte solvents, and greater charge capacity. The need for a suitable electrolyte additive arises as follows: The metallic lithium in the anode of a lithium-ion-based power cell is so highly reactive that in addition to the desired main electrochemical reaction, it engages in side reactions that cause formation of resistive films and dendrites, which degrade performance as quantified in terms of charge capacity, cycle life, shelf life, first-cycle irreversible capacity loss, specific power, and specific energy. The incidence of side reactions can be reduced through the formation of a solid-electrolyte interface (SEI) a thin film that prevents direct contact between the lithium anode material and the electrolyte. Ideally, an SEI should chemically protect the anode and the electrolyte from each other while exhibiting high conductivity for lithium ions and little or no conductivity for electrons. A suitable additive can act as an SEI promoter. Heretofore, most SEI promotion was thought to derive from organic molecules in electrolyte solutions. In contrast, lithium dinitramide is inorganic. Dinitramide compounds are known as oxidizers in rocket-fuel chemistry and until now, were not known as SEI promoters in battery chemistry. Although the exact reason for the improvement afforded by the addition of lithium dinitramide is not clear, it has been hypothesized that lithium dinitramide competes with other electrolyte constituents to react with lithium on the surface of the anode to form a beneficial SEI. Apparently, nitrides and oxides that result from reduction of lithium dinitramide on the anode produce a thin, robust SEI different from the SEIs formed from organic SEI promoters. The SEI formed from lithium dinitramide is more electronically insulating than is the film formed in the presence of an otherwise identical electrolyte that does not include lithium dinitramide. SEI promotion with lithium dinitramide is useful in batteries with metallic lithium and lithium alloy anodes.

Gorkovenko, Alexander A.↗
NASA NTRS2018

Nanoscale Fabrication of Microwave Detectors from Commercially-Available CVD-Grown Monolayer Graphene

Using commercially-available monolayer graphene, synthesized by means of chemical vapor deposition, microwave power sensing elements have been nanofabricated and integrated with microwave-grade test structures suitable for on-wafer probing. The graphene, situated on a thermal oxide, was first cleaned of stray contaminants in a forming gas environment briefly held at 250 degrees Celsius using a rapid thermal annealer. Immediately following this step, the graphene was passivated with a protective aluminum oxide layer (approximately S nm in thickness). Micrometer-scale Corbino disc test structures were then fabricated in direct contact with the graphene using a self-aligned process, which relies on the fact that tetramethylammonium hydroxide develops the photoresist while removing the aluminum oxide. Graphene nanoribbons (with widths as small 400 nm) were then fabricated across the Corbino disc gaps using electron-beam writing in conjunction with a negative tone resist. The same developer exposed the majority of the graphene while defining nanometer-scale lines of photoresist stacked upon aluminum oxide. These stacks served as etch-stops while the unprotected graphene was ion-milled in an oxygen plasma. Finally, the photoresist was removed leaving behind passivated graphene nanoribbons. Damage caused by the fabrication was evaluated by comparing the Raman spectra of the grapheme before and after processing.

detectors↗
NASA NTRS1986

Fuel cell crimp-resistant cooling device with internal coil

A cooling assembly for fuel cells having a simplified construction whereby coolant is efficiently circulated through a conduit arranged in serpentine fashion in a channel within a member of such assembly. The channel is adapted to cradle a flexible, chemically inert, conformable conduit capable of manipulation into a variety of cooling patterns without crimping or otherwise restricting of coolant flow. The conduit, when assembled with the member, conforms into intimate contact with the member for good thermal conductivity. The conduit is non-corrodible and can be constructed as a single, manifold-free, continuous coolant passage means having only one inlet and one outlet. The conduit has an internal coil means which enables it to be bent in small radii without crimping.

Wittel, deceased, Charles F.↗
NASA NTRS1980

Adhesion, friction, and wear of binary alloys in contact with single-crystal silicon carbide

Sliding friction experiments, conducted with various iron base alloys (alloying elements are Ti, Cr, Mn, Ni, Rh and W) in contact with a single crystal silicon carbide /0001/ surface in vacuum are discussed. Results indicate atomic size misfit and concentration of alloying elements play a dominant role in controlling adhesion, friction, and wear properties of iron-base binary alloys. The controlling mechanism of the alloy properties is as an intrinsic effect involving the resistance to shear fracture of cohesive bonding in the alloy. The coefficient of friction generally increases with an increase in solute concentration. The coefficient of friction increases as the solute-to-iron atomic radius ratio increases or decreases from unity. Alloys having higher solute concentration produce more transfer to silicon carbide than do alloys having low solute concentrations. The chemical activity of the alloying element is also an important parameter in controlling adhesion and friction of alloys.

Miyoshi, K.↗
NASA NTRS1983

Improved fabrication techniques for infrared bolometers

Ion implantation and sputter metallization are used to produce ohmic electrical contacts to Ge:Ga chips. The method is shown to give a high yield of small monolithic bolometers with very little low-frequency noise. It is noted that when one of the chips is used as the thermometric element of a composite bolometer it must be bonded to a dielectric substrate. The thermal resistance of the conventional epoxy bond is measured and found to be undesirably large. A procedure for soldering the chip to a metallized portion of the substrate in such a way as to reduce this resistance is outlined. An evaluation is made of the contribution of the metal film absorber to the heat capacity of a composite bolometer. It is found that the heat capacity of a NiCr absorber at 1.3 K can dominate the bolometer performance. A Bi absorber possesses significantly lower heat capacity. A low-temperature blackbody calibrator is built to measure the optical responsivity of bolometers. A composite bolometer system with a throughput of approximately 0.1 sr sq cm is constructed using the new techniques. The noise in this bolometer is white above 2.5 Hz and is slightly below the value predicted by thermodynamic equilibrium theory.

Lange, A. E.↗
NASA NTRS1990

Kinetics and transport at AMTEC electrodes. II - Temperature dependence of the interfacial impedance of Na(g)/porous Mo/Na-Beta-double prime alumina

The exchange current, transfer coefficient, mass-transport parameters, and electrode capacitance at the Na(g)/porous Mo/Na-Beta-double prime alumina solid electrolyte (BASE) phase boundary have been evaluated from 740 to 1220 K. The transfer coefficient exhibits a value close to 0.5 and the exchange current is dominated by collision frequency, with no significant activation energy. Since the porous Mp-electrode adopts a fairly regular microstructure on the BASE surface, the magnitude of the exchange current of mature electrodes directly depends on the actual contact zone of the porous metal film with the BASE ceramic, and decreases slightly as grain growth occurs. The exchange currents and the mass-transport parameters derived for very porous, thin Mo electrodes indicate that the charge-transfer reaction occurs at a small fraction of the interface. High-frequency limiting capacitance and resistance values due to the interface show potential dependence and a value on the order of 1 F/sq m and 0.1-1.0 Ohm-sq cm.

Williams, R. M.↗
NASA NTRS1991

Analysis of foil bearings for high speed operation in cryogenic applications

The general objective of this project is to develop analysis tools which are required for the design of foil bearings to be used in cryogenic applications. During the second year of this project, a general analysis approach and code for journal bearings operating under steady state conditions will be completed. This will be followed by the initiation of an investigation into transient behavior of foil bearings to determine their performance in rotor systems. Foil bearings have been proposed as an alternative to rolling element bearings for use in cryogenic turbopumps in liquid propellant rocket engines. This type of bearing offers several advantages over rolling element bearings since they would use the cryogenic pump fluid for a lubricant and have structural flexibility. These bearings have the potential of high reliability and long life. The bearing surface is constructed of a 'foil' which resists deflection by a combination of bending, membrane, and elastic foundation effects. The relative motion between the rotating shaft and the foil causes pressure in the fluid film to develop. This pressure deflects the the foil surface away from the shaft. Once a full fluid film is established between the foil and the rotor shaft, contact no longer takes place and there is no subsequent wear of the surfaces. The flexible foil structure of the bearing allows it to compensate for minor tolerance and manufacturing defects. This same flexibility also has a significant effect on the dynamic performance of the rotor-bearing system.

Carpino, Marc↗
NASA NTRS1972

Proximity effect between superconductivity and normal metals

The SNS junctions were limited to having gold (n) layers of less than 3000 A in order to avoid having the tin (S) films become normal under the influence of the signal current in the gold. The gold layer was alloyed with 10 wt% copper to shorten its electronic mean free path, increasing the tin layer critical current while decreasing the Josephson critical current. It was also found that a previously reported anomalous voltage shift in the presence of I2 is caused by the tin being driven normal. After deposition, the samples were transferred to a conventional cryostat to provide better thermal contact to the films. This reduction of heating in the films produced more linear I-V characteristics and a change in the constant voltage current gain. In order to achieve power gain the SNS device must be operated at lower temperatures were the effects of fluctuations are less and be constructed such that the input resistance is much reduced and the dynamic output resistance increased. A geometry is proposed using a more sophisticated evaporator.

Meissner, H.↗
NASA NTRS1974

Production development of organic nonflammable spacecraft potting, encapsulating and conformal coating compounds. Volume 1: Discussion, figures, and references

Based upon extensive contacts with vendors, a broad array of non-flammable polymeric specie, and additives generally noted to have flame retarding properties, were considered. The following polymeric matrices were examined: modified silicone and fluorosilicone RTV's polyesters, epoxies, urethanes, and epoxy-urethanes. Optimization of formulations to obtain a suitable balance between the various properties and flammability resistance led to the final selection of a silicone RTV/additive-loaded compound which meets almost all program requirements. The very low valued properties found are within a realistic level of design toleration. Complete formulation, processing, and test data is provided for this compound, EPOCAST 87517-A/B, and the other formulations prepared by the project. Details of those test methods are presented along with procedures utilized in the program. In addition, a description of the special flammability facility previously designed and then modified for this program is also presented.

Lieberman, S. L.↗
NASA NTRS1984

Maximization of Growth Rates During Czochralski Pulling

It was suggested from theory(1-4) that silicon can be grown from the melt at rates far exceeding the current state of the art. Previous theoretical and experimental investigations which predict maximum rates of pulling during Czochralski growth are reviewed. Several experimental methods are proposed to modify the temperature distribution in a growing crystal to achieve higher rates of pulling. A physical model of a Czochralski crystal of germanium in contact with its melt was used to quantitatively determine, by direct measurement of the axial temperature distribution in the solid, the increase in axial temperature gradients effected by an inverted conical heat reflector located above the melt and coaxially about the physical model. Preliminary results indicate that this is an effective method of increasing the thermal resistance between the hot melt and crucible wall and a growing crystal. Under these conditions the enhancement of the interfacial temperature gradients permit a commensurate increase in the rate of crystal pulling.

Wargo, M. J.↗