Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSION BUCKLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Evaluation of Superplastic Forming and Weld-brazing for Fabrication of Titanium Compression Panels

The two titanium processing procedures, superplastic forming and weld brazing, are successfully combined to fabricate titanium skin stiffened structural panels. Stiffeners with complex shapes are superplastically formed using simple tooling. These stiffeners are formed to the desired configuration and required no additional sizing or shaping following removal from the mold. The weld brazing process by which the stiffeners are attached to the skins utilize spot welds to maintain alignment and no additional tooling is required for brazing. The superplastic formed/weld brazed panels having complex shaped stiffeners develop up to 60 percent higher buckling strengths than panels with conventional shaped stiffeners. The superplastic forming/weld brazing process is successfully scaled up to fabricate full size panels having multiple stiffeners. The superplastic forming/weld brazing process is also successfully refined to show its potential for fabricating multiple stiffener compression panels employing unique stiffener configurations for improved structural efficiency.

Royster, D. M.↗

Down-bucklng of a corner of a descending plate

A model of the earth's crust is presented as a set of rigid crustal blocks in which the crust is consumed, compressed, or created only at the boundaries of the blocks. As such the trench boundary moves with respect to the colliding plates because of down-buckling at the corner of the descending plate. It is further shown that this mechanism requires plate consumption of the descending plate at a rate faster than the relative plate motion, which in turn causes infilling of the basin behind the arc to compensate for the increased destruction. It is demonstrated that earthquake, heat flow, paleomagnetic, gravity anomaly, and geologic data derived from Japan and the Sea of Japan support the model.

Lowrey, B. E.↗

Postbuckling and failure characteristics of selected flat rectangular graphite-epoxy plates loaded in compression

Results of an experimental study of the postbuckling response and failure characteristics of 16- and 24-ply quasi-isotropic and 24-ply orthotropic flat rectangular graphite-epoxy plates loaded in compression are examined. Some of the specimens had circular drilled holes or were subjected to low-speed impact damage. The ratio of failure load to buckling load was found to be higher for specimens with lower initial buckling strains than for specimens with higher initial buckling strains. Some specimens supported more than five times their initial buckling load before failing. The specimens failed along a nodal line of the buckling mode in an induced shear failure mode. Holes and impact damage had a more adverse effect on the postbuckling strength of specimens with high initial buckling strains than on the strength of specimens with lower initial buckling strains.

Starnes, J. H., Jr.↗

Postbuckling behavior of graphite-epoxy panels

Structurally efficient fuselage panels are often designed to allow buckling to occur at applied loads below ultimate. Interest in applying graphite-epoxy materials to fuselage primary structure led to several studies of the post-buckling behavior of graphite-epoxy structural components. Studies of the postbuckling behavior of flat and curved, unstiffened and stiffened graphite-epoxy panels loaded in compression and shear were summarized. The response and failure characteristics of specimens studied experimentally were described, and analytical and experimental results were compared. The specimens tested in the studies described were fabricated from commercially available 0.005-inch-thick unidirectional graphite-fiber tapes preimpregnated with 350 F cure thermosetting epoxy resins.

Starnes, J. H., Jr.↗

Nonlinear analysis of compressively loaded linked-plate structures

A method is presented for the geometrically nonlinear analysis of the equilibrium behavior of a general class of compressively loaded, prismatic, linked-plate structures. The semi-analytical method accounts for geometric shape imperfections, and allows the use of laminated composite plate properties. Buckling eigenfunctions are used as displacement shape functions, and the associated second-order displacement fields are incorporated. The nonlinear plate equilibrium equations are expressed in terms of the assumed displacement form, and the Galerkin method is used to obtain a set of algebraic equations which are nonlinear in the modal amplitudes and the load parameter. Buckling eigensolutions for the class of structures under consideration can be obtained from the VIPASA computer code; thus, subject to some additional restrictions in loading and plate anisotropy, structural configurations which can be analyzed with regard to buckling response by VIPASA can be analyzed with regard to geometrically nonlinear response using the new method.

Stoll, Frederick↗

Design considerations for compression panels at elevated temperature

The potential of graphite/polyimide is assessed on a graphite/polyimide honeycomb sandwich panels and stiffened panel concepts to develop lightweight panels for use at elevated temperatures. The capability is attained to correctly predict panel buckling behavior and panel strength at elevated temperatures.

Mcwithey, R. R.↗

Buckling analysis of laminated thin shells in a hot environment

Results are presented of parametric studies to assess the effects of various parameters on the buckling behavior of angle-ply, laminated thin shells in a hot environment. These results were obtained by using a three-dimensional finite element analysis. An angle-ply, laminated thin shell with fiber orientation of (theta/-theta)(sub 2) was subjected to compressive mechanical loads. The laminated thin shell had a cylindrical geometry. The laminate contained T300 graphite fibers embedded in an intermediate-modulus, high-strength (IMHS) matrix. The fiber volume fraction was 55 percent and the moisture content was 2 percent. The residual stresses induced into the laminate structure during the curing were taken into account. Parametric studies were performed to examine the effect on the critical buckling load of the following parameters: cylinder length and thickness, internal hydrostatic pressure, different ply thicknesses, different temperature profiles through the thickness of the structure, and different lay up configurations and fiber volume fractions. In conjunction with these parameters the ply orientation was varied from 0 deg to 90 deg. Seven ply angles were examined: 0 deg, 15 deg, 30 deg, 45 deg, 60 deg, 75 deg, and 90 deg. The results show that the ply angle theta and the laminate thickness had significant effects on the critical buckling load. The fiber volume fraction, the fiber orientations, and the internal hydrostatic pressure had important effects on the critical buckling load. The cylinder length had a moderate influence on the buckling load. The thin shell with (theta/-theta)(sub 2) or (theta/-theta)(sub s) angle-ply laminate had better buckling-load performance than the thin shell with (theta)(sub 4) angle-ply laminate. The temperature profiles through the laminate thickness and various laminates with the different ply thicknesses has insignificant effects on the buckling behavior of the thin shells.

Gotsis, Pascal K.↗

The Effective Width of Curved Sheet After Buckling

This report describes experiments made for the purpose of ascertaining the effective width of circularly curved sheet under pure flexural stress. A relation for the effective width of curved sheets is established. Experiments were made with circular cylinders compressed in longitudinal direction. The sheets were rigidly built in at the sides parallel to the axis of the cylinder.

Wenzek, W A↗

Delamination and Buckling Analysis of a Laminated Component in a High-speed Permanent Magnet Motor

High-speed permanent magnet (PM) machines are widely used because of their high-power density and high efficiency. The high rotation speed also inevitably subjects the PMs to high centrifugal load, which might damage them due to their inherent mechanical vulnerability, such as a much lower tensile strength than the compressive strength. To robustly transfer the torque from the magnet to the shaft, the outer diameter of the laminated rotor core is larger than the inner diameter of the rotor frame to ensure tight contact while working at 20,000 rpm. Motor manufacturing requires the shrink-fit method to assemble the rotor frame and rotor core. However, after the shrink-fit assembly, unexpected local delamination and buckling are observed on the rotor core part. Utilizing finite element simulation, we study the internal stress of assembling these two parts at the provided interference. Simulation results indicate the reasons for the delamination and buckling of the rotor core part and provide suggestions for improving the assembly.

Lin, Lianshan↗

Deformation behavior of nanoscale Al–Al 2 Cu eutectics studied by in situ micropillar compression

We report deformation behavior of nanoscale laser processed Al–Al 2 Cu eutectics at room temperature is characterized through in situ micro-pillar compression testing in a scanning transmission microscope. Interlamellar spacing of Al–Al 2 Cu eutectics varies from hundreds of nanometers to 20 nm. Three different sizes of micro-pillars are fabricated in order to study the deformation behaviors of single colony and multiple colonies, corresponding to the single crystal and polycrystal respectively. For single colonies, lamellar orientations parallel, normal or inclined to the loading direction were tested. The main findings are: 1) the plasticity mechanisms strongly depend on loading orientation: buckling and kinking in the parallel-loaded eutectics, planar sliding along Al–Al 2 Cu lamellar interfaces in the incline-loaded eutectics and localized shearing in the normal-loaded eutectics. 2) the incline-loaded eutectics exhibits the lowest compression flow strength, and the normal-loaded eutectics has the highest compression flow strength. 3) with decreasing inter-lamellar spacing, the strength increases and plasticity is uniformly distributed, as opposed to shear localization. Highest compressive plasticity is observed in polycrystalline eutectics with an ensemble of lamellar orientations with ~20 nm average spacing: 17.9% at flow stress of 1.63 GPa, and degenerate, bimodal morphology: 11.1% at flow stress of 1.36 GPa.

36 MATERIALS SCIENCE↗

Hypersonic Fluid-Thermal-Structural Interactions on a Compression Ramp with an Embedded Compliant Panel

The fluid-thermal-structural interactions of a compliant panel embedded in a compression ramp are explored experimentally at Mach 6. The panel structural response is investigated for turbulent and transitional shock-wave/boundary-layer interactions at five distinct interaction strengths and up to four different pressure differentials. Upstream of the compression corner, fast-response piezoresistive pressure transducers show the feedback of the panel vibrations and static deflection on the upstream pressure fluctuations. The magnitude of the pressure fluctuation rms shows a reduction in the upstream disturbances when a pressure differential is applied across the compliant panel. Photogrammetry and IR thermography are used simultaneously to measure the panel deformations and surface temperature. Panel deformation, frequency shifting, and frequency bifurcation are consistent with post-thermal-buckling behavior.

hypersonic↗

Reactive sputter deposition of piezoelectric Sc 0.12 Al 0.88 N for contour mode resonators

Substitution of Al by Sc has been predicted and demonstrated to improve the piezoelectric response in AlN for commercial market applications in radio frequency filter technologies. Although cosputtering with multiple targets have achieved Sc incorporation in excess of 40%, industrial processes requiring stable single target sputtering are currently limited. A major concern with sputter deposition of ScAl is the control over the presence of non-c-axis oriented crystal growth, referred to as inclusions here, while simultaneously controlling film stress for suspended microelectromechanical systems (MEMS) structures. This work describes 12.5% ScAl single target reactive sputter deposition process and establishes a direct relationship between the inclusion occurrences and compressive film stress allowing for the suppression of the c-axis instability on silicon (100) and Ti/TiN/AlCu seeding layers. An initial high film stress, for suppressing inclusions, is then balanced with a lower film stress deposition to control total film stress to prevent Euler buckling of suspended MEMS devices. Contour mode resonators fabricated using these films demonstrate effective coupling coefficients up to 2.7% with figures of merit of 42. Furthermore, this work provides a method to establish inclusion free films in ScAlN piezoelectric films for good quality factor devices.

36 MATERIALS SCIENCE↗

Reliability Analysis and Reliability-Based Design Optimization of Circular Composite Cylinders Under Axial Compression

This report describes the preliminary results of an investigation on component reliability analysis and reliability-based design optimization of thin-walled circular composite cylinders with average diameter and average length of 15 inches. Structural reliability is based on axial buckling strength of the cylinder. Both Monte Carlo simulation and First Order Reliability Method are considered for reliability analysis with the latter incorporated into the reliability-based structural optimization problem. To improve the efficiency of reliability sensitivity analysis and design optimization solution, the buckling strength of the cylinder is estimated using a second-order response surface model. The sensitivity of the reliability index with respect to the mean and standard deviation of each random variable is calculated and compared. The reliability index is found to be extremely sensitive to the applied load and elastic modulus of the material in the fiber direction. The cylinder diameter was found to have the third highest impact on the reliability index. Also the uncertainty in the applied load, captured by examining different values for its coefficient of variation, is found to have a large influence on cylinder reliability. The optimization problem for minimum weight is solved subject to a design constraint on element reliability index. The methodology, solution procedure and optimization results are included in this report.

Rais-Rohani, Masoud↗

Load Deflection of Dow Corning SE 1700 Simple Cubic Direct Ink Write Materials: Effect of Thickness and Filament Spacing

Dow Corning SE 1700 (reinforced polydimethylsiloxane) porous structures were made by direct ink writing (DIW) in a simple cubic (SC) configuration. The filament diameter was 250 μm. Structures consisting of 4, 8, or 12 layers were fabricated with center-to-center filament spacing (“road width” (RW)) of 475, 500, 525, 550, or 575 μm. Three compressive load-unload cycles to 2000 kPa were performed on four separate areas of each sample; three samples of each thickness and filament spacing were tested. Geometry-dependent buckling of the SC structure was evident. At a given strain during the third loading phase, stress varied inversely with porosity. At strains of 25% and higher, the stress varied inversely with the number of layers (i.e., thickness); however, the relationship between stress and number of layers was more complex at lower strains. Intra-and inter-sample variability of the load deflection response was higher for thinner and less porous structures.

36 MATERIALS SCIENCE↗

Effects of truncation of a predominantly compression load spectrum on the life of a notched graphite/epoxy laminate

The fatigue behavior of a notched, graphite/epoxy (T300/5208) laminate subjected to predominantly compressive loading was explored in a series of constant-amplitude and transport wing spectrum tests. Results of these tests indicate that (1) the amount of local (near the notch) buckling allowed in the tests significantly affected fatigue life; (2) spectrum truncation of either the high- or low-load end of the spectrum produced lives greater than those obtained in the baseline, complete-spectrum test, but life was much more sensitive to truncations at the high-load end; and (3) the Palmgren-Miner linear cumulative damage theory always predicted lives much longer than the actual spectrum loading test lives.

Phillips, E. P.↗

Design and evaluation of a foam-filled hat-stiffened panel concept for aircraft primary structural applications

Geodesically stiffened structures are very efficient in carrying combined bending, torsion, and pressure loading that is typical of primary aircraft structures. They are also very damage tolerant since there are multiple load paths available to redistribute loads compared to prismatically stiffened structures. Geodesically stiffened structures utilize continuous filament composite materials which make them amenable to automated manufacturing processes to reduce cost. The current practice for geodesically stiffened structures is to use a solid blade construction for the stiffener. This stiffener configuration is not an efficient concept and there is a need to identify other stiffener configurations that are more efficient but utilize the same manufacturing process as the solid blade. This paper describes a foam-filled stiffener cross section that is more efficient than a solid-blade stiffener in the load range corresponding to primary aircraft structures. A prismatic hat-stiffener panel design is then selected for structural evaluation in uni-axial compression with and without impact damage. Experimental results for both single stiffener specimens and multi-stiffener panel specimens are presented. Finite element analysis results are presented that predict the buckling and postbuckling response of the test specimens. Analytical results for both the element and panel specimens are compared with experimental results.

Ambur, Damodar R.↗