Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Base Line”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Scoping Study for Fast Flux Testing in the Advanced Test Reactor

The value of fast spectrum reactors remains prominent in the nuclear technology portfolio. The performance of these reactors can be maximized with advancements in nuclear fuel technologies, but development of these technologies is currently held back by lack of fast spectrum test reactors available to the United States. Spectral modification of experiment positions in the thermal spectrum Advanced Test Reactor (ATR) has long been used to support fast reactor fuel development, but these methods have not been progressed to their full potential. This study investigated the use of concentric rings of aluminum-clad fuel plates in ATR flux traps and thermal neutron absorbing filters to increase fast neutron flux on test specimens. This concept was termed the Boosted Energy Advanced Spectrum Test (BEAST). This approach will enable irradiation of advanced fuel designs in prototypic-length fuel pins and representative flux environment to support post irradiation exams, enable transient testing, and produce the type of data that will permit lead test assembly irradiations in true Sodium Fast Reactors (SFRs) when they become available. Neutronic predictions were performed to investigate BEAST design options and thermal hydraulic models were produced to ensure feasibility of BEAST. Two versions were considered based on the geometric limitations of ATR’s small and large flux traps. The small version was found to be preferable due to slightly higher fast flux and fast-to-thermal neutron ratio. Perhaps more influentially, the small flux trap option was also preferred to avoid conflict with ongoing very high temperature reactor fuel irradiation programs in ATR’s large northeast flux trap. The small flux trap option provided less than half the test volume of the large version, but still had adequate volume for seven SFR pins in cross section which could be stacked two-high in ATR’s 1.2m long core to accommodate up to 14 EBR-II size pins. The preference for the small flux trap configuration should be revisited if additional collaborative test programs emerge with the need to irradiate a significant volume of additional specimens. Calculations were performed regarding a lithium deuteride ring to convert thermal neutrons into 14 MeV fusion neutrons. At the time this report was written these calculations were partially complete and it remains to be seen whether the concept would be worth including in BEAST. Given the preference for the small flux trap option, which does not afford enough room for the 14 MeV ring, it was concluded to defer future work on the lithium deuteride ring. This decision could be revisited if fusion material research programs emerge for collaborative testing in BEAST. A cadmium-lined specimen holder design was found to be adequate in filtering thermal neutrons and preferred over other neutron absorbers based on past experience with cadmium baskets. It was acknowledged that cadmium-bearing hardware would become depleted and need to be replaced occasionally, which appeared feasible from a mechanical design perspective. Neutronic studies investigated different enrichment levels in the booster fuel using uranium-molybdenum alloy dispersion fuel which has performed well in past ATR irradiations. Both options were able to drive fuel pins to SFR-like fission heating rates. The high enriched booster fuel option outperformed the low enriched option by ~20% on key metrics including fast flux and fast-to-thermal ratio, but the low enriched option was favored in order to broaden options for potential fuel suppliers. The preferred BEAST design options including cadmium filter with low enriched booster fuel in the small flux trap configuration was predicted to achieve 6.2E14 n/cm2sec fast flux (>0.1 MeV) with a fast-to-thermal ratio of 44.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Variable Stars in the Giant Satellite Galaxy Antlia 2

We report 350 pulsating variable stars found in four DECam fields (~12 deg 2 ) covering the Antlia 2 satellite galaxy. The sample of variables includes 318 RR Lyrae stars and eight anomalous Cepheids in the galaxy. Reclassification of several objects designated previously to be RR Lyrae as anomalous Cepheids get rid of the satellite's stars intervening along the line of sight. This in turn removes the need for prolific tidal disruption of the dwarf, in agreement with the recently updated proper motion and pericenter measurements based on Gaia EDR3. There are also several bright foreground RR Lyrae stars in the field, and two distant background variables located ~45 kpc behind Antlia 2. We found RR Lyrae stars over the full search area, suggesting that the galaxy is very large and likely extends beyond our observed area. The mean period of the RRab in Antlia 2 is 0.599 days, while the RRc have a mean period of 0.368 days, indicating the galaxy is an Oosterhoff-intermediate system. The distance to Antlia 2 based on the RR Lyrae stars is 124.1 kpc (μ 0 = 20.47) with a dispersion of 5.4 kpc. We measured a clear distance gradient along the semimajor axis of the galaxy, with the southeast side of Antlia 2 being ~13 kpc farther away from the northwest side. This elongation along the line of sight is likely due to the ongoing tidal disruption of Ant 2.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Newly developed sugarbeet lines with altered postharvest respiration rates differ in transcription factor and glycolytic enzyme expression

Respiration is the principal cause for postharvest sucrose loss in sugarbeet (Beta vulgaris L.) roots. Although reductions in respiration rate could mitigate these losses, developing sugarbeet cultivars and storage procedures that reduce respiration are hindered by a lack of knowledge of the genetic and metabolic factors that control storage respiration rate. Research was conducted to identify genes and gene products that affect storage respiration rate by creating two sugarbeet lines that differ in respiration rate and characterizing gene expression differences between these lines. Sugarbeet lines F1056 and F1057, which differ by up to 42% in respiration rate, were created by divergent selection of a sugarbeet population using root respiration rate after 30 d in storage as the principal selection criterion. RNA sequencing identified 287 differentially expressed genes (DEGs) between these lines on the day of harvest and after 28-d storage. Of these DEGs, nine encoded transcription factors and five encoded enzymes involved in the respiratory pathway. Other DEGs contributed to a variety of biological and molecular functions based on gene ontology classifications. Of respiratory pathway DEGS, genes for NAD+- and NADP+-dependent forms of glyceraldehyde-3-phosphate dehydrogenase were of note due to their high upregulation in the high respiring line and for their established role in glycolysis, a pathway identified as a likely bottleneck in respiratory substrate production. Overall, lines F1056 and F1057 provide new tools for investigating genetic and physiological differences in storage respiration rate, and their DEGs identify candidates for genes affecting sugarbeet root respiration rate.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Deployment of salt sample extraction system at an engineering-scale electrorefiner

The goal of the salt sampling program at Argonne is to develop and deploy automated molten salt sampling approaches for interfacing relevant unit operations with salt analysis to improve the timeliness of sampling-based accountancy measurements. Two technologies under development in support of this goal are a vacuum sampling loop module and a high-throughput pneumatic sample generator module. Compared to traditional point sampling approaches (i.e., dip probes), the vacuum sampling loop facilitates the collection of a larger cross-section of the bulk salt in order to collect more representative samples. The vacuum sampling approach also eliminates the risk of dross contamination of samples and avoids the use of moving parts in the salt. The pneumatic sample generator module is used to facilitate high-throughput sample analysis to improve the measurement precision of any given analytical technique by averaging out random sampling and measurement errors. In FY21, two methods for integrating these two modules were tested including direct fluidic coupling and coupling using a solid salt transfer mechanism. Solid salt transfer was ultimately selected over fluidic coupling, primarily to enable the transport of samples over longer distances to support automated at-line integration with high-precision techniques (such as microcalorimetry) that cannot withstand the conditions near an electrorefining process. To facilitate rapid solid salt coupling, new mechanisms were developed for rapidly charging and discharging salt sample tubes at the vacuum sampling loop and pneumatic sample generator modules, respectively. While the charging mechanism will be deployed in FY22, the discharge mechanism was tested in FY21 and is described here. The solid salt tube transfer method was deployed at one of Argonne’s engineering-scale electrorefiners to implement at-line high-throughput pneumatic micro-sample generation capabilities. The approach was used to generate precise uranium- and lanthanide-bearing electrorefiner micro-samples with the specific dimensions requested by researchers at Los Alamos National Laboratory for use in testing their novel microcalorimeter x-ray techniques. The solid salt transfer mechanism proved not only to be an effective means of integrating the precision sample generator with vacuum sampling, but also improved the performance of the sampler generator. To discharge salt from the sample tubes at the sampler generator, tube segments were inserted directly into the sample generator’s Helmholtz chamber and pressure pulse actuations were used to generate precision molten salt samples directly from the tube segments. The direct insertion of sample tubes into the sample generator enabled rapid loading of the salt and prevented salt from contacting most of the interior surfaces of the sample generator, which eliminated cross-contamination between runs. The vacuum sampling-loop tube charging mechanism will support high-throughput tube sampling operations by employing a dynamic vacuum filling process to fill short charge tubes that are configured to be rapidly connected and disconnected from the loop. The dynamic vacuum sampling operation will be automated, and sample tube handling can be executed with simple overhead actuation. Because the modular sampling approach described here eliminates the need for new high-radiation sample handling capabilities, salt-wetted seals, salt-wetted moving parts, and heated transfer lines outside the electrorefiner, it will address most of the remaining technical challenges for the at-line deployment of high-precision analytical techniques which will enable significant reductions in the time delay for sampling-based high-precision accountancy measurements.

42 ENGINEERING↗
DOE OSTI2022

Genetic mapping of sugarcane aphid resistance in sorghum line SC112-14

Sugarcane aphid [Melanaphis sacchari (Zehntner)] is a destructive pest that has had an economic effect on sorghum in North America since 2013. The identification, development, and use of resistant sorghum germplasm is the most feasible strategy to control the pest. Nevertheless, the genetic control of sugarcane aphid (SCA) resistance is unknown for most sorghum resistant lines. To identify the genetic regions that confer SCA resistance in sorghum line SC112-14, 103 recombinant inbred lines (RILs) derived by its cross with the susceptible line PI 609251 were evaluated for their SCA resistance response in Georgia during two consecutive years. The resistance response was determined based on two ratings (2 wk apart) for aphid population size (APS) and aphid-induced plant damage (APD) each year. Segregation for SCA resistance was observed for the first APS and both APD ratings, and the broad-sense heritability estimate ranged from .71 to .76, respectively. A quantitative trait locus analysis using a high-density linkage map of 3,852 single nucleotide polymorphisms (SNPs) detected an 81-kb genomic region on chromosome 6 that explained 50–55% of the phenotypic variation. Comparative mapping analysis found that the resistance locus in SC112-14 is located 8- and 10-cM upstream of the Henong 16 (RMES1) and Tx2783 resistance loci, respectively, and encloses the SNP Sbv3.1_06_2316351 associated in Haitian resistant lines. Therefore, the line SC112-14 is an additional SCA resistance source that can be combined or strategically used with other resistance sources to assure a more robust host plant resistance to the SCA.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

Hydration‐Induced β‐Sheet Crosslinking of α‐Helical‐Rich Spider Prey‐Wrapping Silk

Abstract Due to its moderate strength (≈700 MPa) and impressive extensibility before breaking (≈60–80%), orb‐weaving spider aciniform (AC) prey‐wrapping silks are actually the toughest of the spider silks but are remarkably understudied. The previous results indicate that native AC silk fibers are an α‐helix rich coiled‐coil/β‐sheet hybrid nanofiber, and that conversion of disordered or helical domains to β‐sheet aggregates is surprisingly minimal and overall β‐sheet content is low (≈15%). In this work, it is demonstrated through scanning electron microscopy that native AC silk fibers undergo matted cross‐linking upon exposure to moisture that increases silk stiffness. The unique molecular mechanism of water‐induced cross‐linking is revealed with solid‐state NMR (SSNMR) methods; water‐induced morphological changes are correlated with an increase in AC silk protein β‐sheet content, and additionally a minor unfolding of coiled‐coil regions is observed. Continued and increased β‐sheet cross‐linking is observed upon application of mechanical shear. The size of these β‐sheet domains to be 4–6 nm using Wide‐Line Separation SSNMR is determined. The observation that merely water treatment can be used to convert a protein‐based material from a flexible/extensible α‐helix‐rich fiber to a rigid crossed‐linked β‐sheet mat is a novel observation that should provide new avenues in bioinspired materials design.

Stengel, Dillan↗
DOE OSTI2025

Use of Frit‐Disc Crucible Sets to Make Solution Growth More Quantitative and Versatile

The recent availability of step‐edge, frit‐disc crucible sets (generally sold as Canfield Crucible Sets or CCS) has led to multiple innovations associated with the group's use of solution growth. The use of CCS allows for the clean separation of liquid from solid phases during the growth process. This clean separation enables the reuse of the decanted liquid, either allowing for simple, economic, savings associated with recycling expensive precursor elements or allowing for the fractionation of a growth into multiple, small steps, revealing the progression of multiple solidifications. Clean separation of liquid from solid phases also allows for the determination of the liquidus line (or surface) and the creation, or correction, of composition–temperature phase diagrams. The reuse of clean decanted liquid has also allowed to prepare liquids ideally suited for the growth of large single crystals of specific phases by tuning the composition of the melt to the optimal composition for growth of the desired phase, often with reduced nucleation sites. Finally, it is discussed how solution growth and CCS use can be harnessed to provide a plethora of composition–temperature data points defining liquidus lines or surfaces with differing degrees of precision to either test or anchor artificial intelligence and/or machine‐learning‐based attempts to augment and extend the limited experimentally determined database.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

In situ TEM annealing of neutron-irradiated Ti reveals a two-stage mechanism for elevated temperature radiation damage recovery

Understanding how irradiation-induced defects evolve at elevated temperatures is of critical importance to predicting materials' behavior under steady-state and accident scenarios. However, such mechanistic insight into microstructural evolution is limited by the nature of ex situ annealing and subsequent imaging. Here we show direct observation and quantification of defect recovery in neutron-irradiated Ti using in situ transmission electron microscopy (TEM) annealing experiments. In agreement with our prior work, and at temperatures below the irradiation temperature (T irr = 300 °C), dislocation loops are observed to glide. At elevated temperatures (>500 °C), dislocation lines become mobile and promote significant recovery of the microstructure. These mechanisms challenge the established electron irradiation-based model for radiation damage recovery, which originally suggests dissolution of static defect clusters, and demonstrates the importance of in situ characterization in understanding defect evolution in irradiated materials.

Hirst, Charles A. [Univ. of Michigan, Ann Arbor, M↗
DOE OSTI2021

Visible spectroscopy of highly charged tungsten ions with the JET charge exchange diagnostic

Since the installation of the ITER-like wall on the JET tokamak, visible emission from a broad range of tungsten charge states has complicated plasma ion temperature and toroidal rotation measurements. A plethora of charge exchange transitions, from ions up to W 56+ , and 21 suspected magnetic dipole transitions have been observed. In particular W 39+ and W 46+ charge exchange emission contaminates the long-established carbon measurement at 529 nm. Fortunately the wavelength and relative intensity of the tungsten charge exchange lines is predictable and their influence can be mitigated when they are included in the spectral fit. Neon based charge exchange measurements at 525 nm are now preferred on JET since the ITER-like wall, however in this case an unidentified tungsten magnetic dipole transition contaminates the spectrum when the electron temperature is low.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

SDSS-IV MaNGA: the physical origin of off-galaxy H α blobs in the local Universe

ABSTRACT H α blobs are off-galaxy emission-line regions with weak or no optical counterparts. They are mostly visible in H α line, appearing as concentrated blobs. Such unusual objects have been rarely observed and studied, and their physical origin is still unclear. We have identified 13 H α blobs in the public data of MaNGA survey, by visually inspecting both the optical images and the spatially resolved maps of H α line for ∼4600 galaxy systems. Among the 13 H α blobs, 2 were reported in previously MaNGA-based studies and 11 are newly discovered. This sample, though still small in size, is by far the largest sample with both deep imaging and integral field spectroscopy. Therefore, for the first time we are able to perform statistical studies to investigate the physical origin of H α blobs. We examine the physical properties of these H α blobs and their associated galaxies, including their morphology, environments, gas-phase metallicities, kinematics of ionized gas, and ionizing sources. We find that the H α blobs in our sample can be broadly divided into two groups. One is associated with interacting/merging galaxy systems, of which the ionization is dominated by shocks or diffuse ionized gas. It is likely that these H α blobs used to be part of their nearby galaxies, but were stripped away at some point due to tidal interactions. The other group is found in gas-rich systems, appearing as low-metallicity star-forming regions that are visually detached from the main galaxy. These H α blobs could be associated with faint discs, spiral arms, or dwarf galaxies.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Emergence of pseudoresonance in high-intensity resonant inelastic x-ray scattering

We report resonant inelastic x-ray scattering (RIXS) spectra of neon atoms interacting with intense x-ray pulses generated using an x-ray free-electron laser (XFEL). We find that an unexpected peak emerges near the 𝐾⁢𝛼 line of Ne, which does not coincide with any physical resonances of neon ions. We perform theoretical calculations based on a quantum-state-resolved rate-equation approach with x-ray-induced processes including possible resonant excitations. Our dynamics simulations demonstrate that a sequence of multiple resonant photoabsorption events are involved and the interplay of those multiple resonances in combination with the relatively large spectral bandwidth of XFEL radiation leads to the emergent resonance-like structure at a position where no resonances exist. Our finding offers critical guidance for future applications of high-intensity RIXS at XFEL facilities.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

Outbursting Young Stellar Object PGIR 20dci in the Perseus Arm

We report the discovery of a likely outbursting Class I young stellar object, associated with the star-forming region NGC 281-W (distance ~2.8 kpc). The source is currently seen only at infrared wavelengths, appearing in both the Palomar Gattini InfraRed (1.2 μm) and the Near-Earth Object Wide-field Infrared Survey Explorer (3.4 and 4.6 μm) photometric time-domain surveys. Recent near-infrared imaging reveals a new, extended scattered light nebula. Recent near-infrared spectroscopy confirms the similarity of PGIR 20dci to FU Ori–type sources, based on strong molecular absorption in CO, H{sub 2}O, and OH; weak absorption in several atomic lines; and a warm wind/outflow as indicated by a P Cygni profile in the He i λ10830 line. This is a rare case of an FU Ori star with a well-measured long-term photometric rise before a sharper outburst, and the second instance of an FU Ori star with a documented two-step brightening in the mid-infrared.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2024

SCIMON: Scientific Inspiration Machines Optimized for Novelty

We explore and enhance the ability of neu- ral language models to generate novel scien- tific directions grounded in literature. Work on literature-based hypothesis generation has traditionally focused on binary link prediction— severely limiting the expressivity of hypothe- ses. This line of work also does not focus on optimizing novelty. We take a dramatic depar- ture with a novel setting in which models use as input background contexts (e.g., problems, experimental settings, goals), and output natu- ral language ideas grounded in literature. We present SCIMON, a modeling framework that uses retrieval of “inspirations” from past scien- tific papers, and explicitly optimizes for novelty by iteratively comparing to prior papers and up- dating idea suggestions until sufficient novelty is achieved. Comprehensive evaluations reveal that GPT-4 tends to generate ideas with over- all low technical depth and novelty, while our methods partially mitigate this issue. Our work represents a first step toward evaluating and developing language models that generate new ideas derived from the scientific literature.

Ji, Heng↗
DOE OSTI2021

Ensuring reliable connectivity to cellular-connected UAVs with up-tilted antennas and interference coordination

To integrate unmanned aerial vehicles (UAVs) in future large-scale deployments, a new wireless communication paradigm, namely, the cellular-connected UAV has recently attracted interest. However, the line-of-sight dominant air-to-ground channels along with the antenna pattern of the cellular ground base stations (GBSs) introduce critical interference issues in cellular-connected UAV communications. In particular, the complex antenna pattern and the ground reflection (GR) from the down-tilted antennas create both coverage holes and patchy coverage for the UAVs in the sky, which leads to unreliable connectivity from the underlying cellular network. To overcome these challenges, in this paper, we propose a new cellular architecture that employs an extra set of co-channel antennas oriented towards the sky to support UAVs on top of the existing down-tilted antennas for ground user equipment (GUE). To model the GR stemming from the down-tilted antennas, we propose a path-loss model, which takes both antenna radiation pattern and configuration into account. Next, we formulate an optimization problem to maximize the minimum signal-to-interference ratio (SIR) of the UAVs by tuning the up-tilt (UT) angles of the up-tilted antennas. Since this is an NP-hard problem, we propose a genetic algorithm (GA) based heuristic method to optimize the UT angles of these antennas. After obtaining the optimal UT angles, we integrate the 3GPP Release-10 specified enhanced inter-cell interference coordination (eICIC) to reduce the interference stemming from the down-tilted antennas. Our simulation results based on the hexagonal cell layout show that the proposed interference mitigation method can ensure higher minimum SIRs for the UAVs over baseline methods while creating minimal impact on the SIR of GUEs.

3GPP↗
DOE OSTI2026

A Parametric Reduced-Order Model for Inverter Short-Circuit Response in Protection Studies

This paper presents a reduced-order model (ROM) for grid-following (GFL) inverters that reproduces inverter fault current trajectories, including sub transients, transient, and steady-state phases, across a range of fault types, locations, and pre-fault operating points. . The proposed model is developed by: Constructing the positive- and negative-sequence current with parameterization fitted by large data training and fitting Validating using EMT simulation against EMT full model and demonstrating the ROM's capability to capture fault current magnitude, phase angle, and oscillatory transients. Building a standard EMT simulation platform library component for easy configuration and application.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Topological Machine Learning Methods for Power System Responses to Contingencies

While deep learning tools, coupled with the emerging machinery of topological data analysis, are proven to deliver various performance gains in a broad range of applications, from image classification to biosurveillance to blockchain fraud detection, their utility in areas of high societal importance such as power system modeling and, particularly, resilience quantification in the energy sector yet remains untapped. To provide fast acting synthetic regulation and contingency reserve services to the grid while having minimal disruptions on customer quality of service, we propose a new topology-based system that depends on a neural network architecture for impact metric classification and prediction in power systems. This novel topology-based system allows one to evaluate the impact of three power system contingency types, in conjunction with transmission lines, transformers, and transmission lines combined with transformers. We show that the proposed new neural network architecture equipped with local topological measures facilitates more accurate classification of unserved load as well as the amount of unserved load. In addition, we are able to learn more about the complex relationships between electrical properties and local topological measurements on their simulated response to contingencies for the NREL-SIIP power system.

contingency analysis↗
DOE OSTI2023

Carbide-based fuel assembly for thermal propulsion applications

Carbide-based fuel assembly includes outer structural member of ceramic matrix composite material, the interior surface of which is lined in higher temperature regions with an insulation layer of porous refractory ceramic material. Continuous insulation layer extends the length of the fuel assembly or separate insulation layer sections have a thickness increasing step-wise along the length of the fuel assembly from upper (inlet) section towards bottom (outlet) section. A fuel element positioned inward of the insulation layer and between support meshes has a fuel composition including HALEU and the form of a plurality of individual elongated fuel bodies or one or more fuel monolith bodies containing coolant flow channels. Fuel assemblies are distributively arranged in a moderator block, with upper end of the outer structural member attached to an inlet for propellant and lower end of the outer structural member operatively interfaced with a nozzle forming a nuclear thermal propulsion reactor.

Barringer, Eric A.↗
DOE OSTI2025

Lines of Bound States in the Continuum in Monodisperse Microsphere Structures

Incorporating epitaxially grown active semiconductor media into self-assembled microsphere crystals has remained a major challenge as the curved geometry of the spheres is incompatible with conventional planar growth and patterning techniques. As a result, active photonic devices based on such self-assembled structures, which have other desirable properties such as enabling the rapid assembly of large area systems, have been elusive. Here, we numerically demonstrate an alternative route to creating high-Q resonances in microsphere-based nanophotonic assemblies compatible with standard optical gain materials. We show that close-packed layers of monodisperse microspheres can exhibit symmetry bandgaps, regardless of their layer stacking order. Thus, this microsphere environment can be used to create lines of bound states in the continuum (BICs) of an embedded slab made of active material. Using a realistic ZnS@SiO 2 (core-shell) architecture and sphere diameters compatible with scalable colloidal assembly, we predict sharp spectral features in angle-resolved transmission that trace these lines of BICs and persist in the presence of some fabrication disorder. Altogether, in enabling the integration of unpatterned epitaxial gain slabs with large-area colloidal microsphere assemblies, this approach opens a practical path toward active, dynamically reconfigurable photonic devices that leverage BIC physics for narrow-linewidth lasing and enhanced light–matter interactions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗