Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AXIAL RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Near-Exit Pressure Fluctuations in Jets from Circular and Rectangular Nozzles

This article documents some experimental observations made for near-exit unsteady pressure fluctuations in high-speed jets. These fluctuations are apparently related to ‘trapped waves’ within the jet potential core as investigated and reported recently by other researchers. Round nozzles of three different diameters and rectangular nozzles of three different aspect ratios are studied. The pressure fluctuations manifest as a series of peaks in the spectra. These ‘trapped wave spectral peaks’ are found with all nozzles. Their characteristics and variations with axial and radial distances as well as with jet Mach number are documented. Effects of initial boundary layer state and the presence of a surface nearby as well as the scaling of the frequencies of the spectral peaks are studied and discussed.

Zaman, K. B. M. Q.↗
NASA NTRS1976

Effect of tip clearance on performance of small axial hydraulic turbine

The first two stages of a six stage liquid oxygen turbine were tested in water. One and two stage performance was determined for one shrouded and two unshrouded blade end configurations over ranges of clearance and blade-jet speed ratio. First stage, two stage, and second stage efficiencies are included as well as the effect of clearance on mass flow for two stage operation.

Boynton, J. L.↗
NASA NTRS1976

Measurements in the mixing region of a turbulent jet in a coflowing airstream

The mixing region of a turbulent jet is an important example of an intermittent turbulent shear flow. There are a great deal of interest in this region because of interest in jet noise and STOL aircraft which use upper surface blowing or externally blown flap configurations to increase lift. A detailed study of the one point statistical properties of a smoke laden jet was made using a combination of a laser velocimeter and a light scattering system. The jet, with a 14 to 1 contraction, was placed inside a wind tunnel where the ratio of the jet exit velocity to free stream was 5.1 to 1. All measurements are made for a jet Reynolds number of 22,600. Among the quantities measured are mean axial and radial velocities, axial and radial intensities, power spectra, mean smoke concentration, concentration intensities, concentration spectra, intermittencies and velocity-concentration correlations. The results are compared with hot-wire data where available.

Morton, J. B.↗
NASA NTRS1981

Bending-torsion flutter of a highly swept advanced turboprop

Experimental and analytical results are presented for a bending-torsion flutter phenomena encountered during wind-tunnel testing of a ten-bladed, advanced, high-speed propeller (turboprop) model with thin airfoil sections, high blade sweep, low aspect ratio, high solidity and transonic tip speeds. Flutter occurred at free-stream Mach numbers of 0.6 and greater and when the relative tip Mach number (based on vector sum of axial and tangential velocities) reached a value of about one. The experiment also included two- and five-blade configurations. The data indicate that aerodynamic cascade effects have a strong destabilizing influence on the flutter boundary. The data was correlated with analytical results which include aerodynamic cascade effects and good agreement was found.

Mehmed, O.↗
NASA NTRS1991

Deformation and stress response of composite laminated shells under internal pressure

This paper presents a theoretical study of the response of filament wound composite shells under internal pressure. Each layer of the material is generally cylindrically anisotropic. By using cylindrically anisotropic elasticity field equations and Lekhnitskii's stress functions, a system of sixth-order ordinary differential equations is obtained. The general expressions for the stresses and displacements in the laminated composite shells under internal pressure are discussed. Two composite systems, graphite/epoxy and glass/epoxy, are selected to demonstrate the influence of degree of material anisotropy and fiber orientations on the axial and induced twisting deformation. Stress distributions of (45/-45)s symmetric angle-ply fiber-reinforced laminated shells are shown to illustrate the effect of radius-to-thickness ratio.

Yuan, F. G.↗
NASA NTRS1948

Altitude-wind-tunnel investigation of a 4000-pound-thrust axial-flow turbojet engine VI : combustion-chamber performance

An analysis of the performance of the types A, B, and C combustion chambers of the 4000-pound-thrust axial-flow turbojet engine is presented. The data were obtained from investigations of the complete engine over a range of pressure altitudes from 5000 to 40,000 feet and ram pressure ratios from 1.00 to 1.86. The combustion-chamber pressure losses, the effect of the losses on cycle efficiency, and the combustion efficiency are discussed.

Pinkel, I Irving↗
NASA NTRS1998

Mixing of Multiple Jets With a Confined Subsonic Crossflow

Results from a recently completed enhanced mixing program are summarized in the two technical papers. These studies were parts of a High Speed Research (HSR)-supported joint Government/industry/university program that involved, in addition to the NASA Lewis Research Center, researchers at United Technologies Research Center, Allison Engine Company, CFD Research Corporation, and the University of California, Irvine. The studies investigated the mixing of jets injected normal to a confined subsonic mainsteam in both rectangular and cylindrical ducts. Experimental and computational studies were performed in both nonreacting and reacting flows. The orifice geometries and flow conditions were selected as typical of the complex three-dimensional flows in the combustion chambers in low-emission gas turbine engines. The principal conclusion from both the experiments and modeling was that the momentum-flux ratio J and orifice spacing S/H were the most significant flow and geometry variables, respectively. Conserved scalar distributions were similar-independent of reaction, orifice diameter H/d, and shape-when the orifice spacing and the square root of the momentum-flux ratio were inversely proportional. Jet penetration was critical, and penetration decreased as either momentum-flux ratio or orifice spacing decreased. We found that planar averages must be considered in context with the distributions. The mass-flow ratios and the orifices investigated were often very large. The jet-to-mainstream mass-flow ratio was varied from significantly less than 1 to greater than 1. The orifice-area to mainstream-cross-sectional-area was varied from approx. 0 to 0.5, and the axial planes of interest were often just downstream of the orifice trailing edge. Three-dimensional flow was a key part of efficient mixing and was observed for all configurations. As an example of the results, the accompanying figure shows the effects of different rates of mass addition on the opposite walls of a rectangular duct.

Holdeman, James D.↗
NASA NTRS2009

Rotary drum separator system

A rotary phase separator system generally includes a step-shaped rotary drum separator (RDS) and a motor assembly. The aspect ratio of the stepped drum minimizes power for both the accumulating and pumping functions. The accumulator section of the RDS has a relatively small diameter to minimize power losses within an axial length to define significant volume for accumulation. The pumping section of the RDS has a larger diameter to increase pumping head but has a shorter axial length to minimize power losses. The motor assembly drives the RDS at a low speed for separating and accumulating and a higher speed for pumping.

Barone, Michael R.↗
DOE OSTI2023

Numerical and boundary condition effects on the prediction of detonation engine behavior using detailed numerical simulations

High-fidelity numerical simulations of an experimental rotating detonation engine with discrete fuel/air injection were conducted. A series of configurations with different feed-plenum pressures but with constant equivalence ratio were studied. Detailed chemical kinetics for the hydrogen/air system is used. A resolution study for the full rotating detonation engine (RDE) system simulation is also conducted. Two kinds of boundary conditions, a total pressure boundary and a constant mass flow rate boundary, are used to assess the effects of the inlet boundary. As mass flow rate is increased, the total pressure boundary causes more error in the axial pressure distribution while the constant mass flow rate gives a better solution for all cases ran. The simulations confirm experimental findings, and reproduce qualitative as well as some of the quantitative trends. These results demonstrate that a) fuel-air mixing is highly non-uniform within the detonation chamber, leading to variations in local equivalence ratio, b) the fuel and oxidizer injectors experience significant backflow as the detonation wave passes over, but recover at different rates which further augments the inefficiencies in mixing, and c) parasitic combustion in the mixing region makes the detonation wave weak by extending the reaction zone across the wave.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

First Evidence of Axial Shape Asymmetry and Configuration Coexistence in Zn 74 : Suggestion for a Northern Extension of the N = 40 Island of Inversion

The excited states of N=44 74 Zn were investigated via γ-ray spectroscopy following 74 Cu β decay. By exploiting γ-γ angular correlation analysis, the 2$_2^+$, 3$_1^+$, 0$_2^+$, and 2$_3^+$ states in 74 Zn were firmly established. The γ-ray branching and E2/M1 mixing ratios for transitions deexciting the 2$_2^+$, 3$_1^+$, and 2$_3^+$ states were measured, allowing for the extraction of relative B(E2) values. In particular, the 2$_3^+$→0$_2^+$ and 2$_3^+$→4$_1^+$ transitions were observed for the first time. Here the results show excellent agreement with new microscopic large-scale shell-model calculations, and are discussed in terms of underlying shapes, as well as the role of neutron excitations across the N=40 gap. Enhanced axial shape asymmetry (triaxiality) is suggested to characterize 74 Zn in its ground state. Furthermore, an excited K=0 band with a significantly larger softness in its shape is identified. A shore of the N=40 "island of inversion" appears to manifest above Z=26, previously thought as its northern limit in the chart of the nuclides.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

EGS Collab Experiment 2: 4100 Foot Level Elastic Property Data

Static and dynamic elastic properties (Young's modulus, Shear Modulus, P-wave Modulus, and Poisson's Ratio) of amphibolites and rhyolites from the TV4100 and TH4100 boreholes at the Sanford Underground Research Laboratory (SURF). Elastic properties include Young's modulus, Poisson's ratio, shear modulus, and p-wave modulus. Raw data from the experiments and slides describing the experimental procedure and a summary of results are included, along with a readme file with additional definitions and information.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

The Function of Horn Ridges for Impact Damping

This study explores the damping effects of ram horn ridges on mechanical impacts resulting from ramming. We measured the amplitudes and frequencies of ridges along the axial (pitch) direction of the ridges of ram horns obtained from eight specimens across six different species. While the horns shared a similar spiral-shaped pattern with surface ridges, our findings show variations among the horns, including ridge spacing and growth trends. Additionally, we employed finite element analysis (FEA) to compare a ridged horn model with a non-ridged counterpart to provide an understanding of the damping characteristics of the surface ridges. Our FEA results reveal that the ridged horn decreased the initial ramming pressure by 20.7%, increased the shear stress by 66.9%, and decreased the axial strain by 27.3%, the radial strain by 16.7%, and the shear strain by 14.3% at a 50 ms impact duration compared to those of the non-ridged horn. The damping ratio was increased by 7.9% because of the ridges. This study elucidates three primary functions of the different species of ram horns’ spirals and ridges: (1) to transfer longitudinal waves into shear waves, (2) to filter shear waves, and (3) to stabilize the structure by mitigating excessive strain.

bio-inspired design↗
NASA NTRS1972

An experimental investigation of vortex generation in a turbulent boundary layer undergoing adverse pressure gradient

The existence of streamwise vortices in nominally 2-dimensional boundary layers undergoing adverse pressure gradient was investigated. The free stream Mach number was 5.75, the wall to stagnation temperature ratio was 0.63 and the Reynolds number based on free stream conditions was 3.9 x 10 to the 7th power/ft. The model consisted of an axisymmetric compression flare preceded by a cylindrical axially symmetric body. A natural turbulent boundary layer was established well ahead of the compression region. Boundary layer profiles of static pressure, pitot pressure, and stagnation temperature were taken at a surface station with a local inclination of 20 deg. Profile measurements were obtained at various peripheral stations. The measurements revealed zero peripheral variations at the surface of the body and at the edge of the boundary layer. However, distinct wavy pressure variations were observed within the boundary layer profiles, indicating the existence of longitudinal vortex cells within the boundary layer.

Zakkay, V.↗
NASA NTRS1975

Cold-air performance of a 12.766-centimeter-tip-diameter axial-flow cooled turbine. 1: Design and performance of a solid blade configuration

A solid blade version of a single-stage, axial-flow turbine was investigated to determine its performance over a range of speeds from 0 to 105 percent of equivalent design speed and over a range of total to static pressure ratios from 1.62 to 5.07. The results of this investigation will be used as a baseline for comparison with those obtained from a cooled version of this turbine.

Haas, J. E.↗
NASA NTRS1976

Performance of a low-pressure fan stage with reverse flow

The reverse flow aerodynamic performance of a 51-centimeter-diameter fan stage is presented. The stage was tested with the variable pitch rotor blades set through feather at -75 deg, -80 deg, and -85 deg from design setting angle. Of the three tested the stage with the rotor blades set at -75 deg exhibited the highest pressure ratio and highest flow. For all three configurations, there was little or no flow in the inner third of the exit passage due to the rotor blade being almost perpendicular to the axial direction in the hub region.

Moore, R. D.↗
NASA NTRS1979

Cold-air performance of free power turbine designed for 112-kilowatt automotive gas-turbine engine. 2: Effects of variable stator-vane-chord setting angle on turbine performance

The cold-air performance of an axial-flow power turbine with a variable stator designed for a 112-kW automotive gas-turbine engine was determined at speeds from 30 to 110 percent of design and at pressure ratios from 1.11 to 2.67. Performance is presented in terms of equivalent mass flow, torque, power, and efficiency for stator-vane-chord setting angles of 26 degs, 30 degs, 35 degs (design), 40 degs, 45 degs, and 50 degs. Turbine braking performance at a nominal stator setting angle of 107 degs is also presented. Turbine efficiency increased with increasing stator setting angle. A 10-point efficiency increase was obtained by opening the stator from the design setting angle of 35 degs to a setting angle of 45 degs.

Mclallin, K. L.↗
NASA NTRS1982

Forward acoustic performance of a model turbofan designed for a high specific flow (QF-14)

Forward noise and overall aerodynamic performance are presented for a high-tip-speed fan having an exceptionally high average axial Mach number at the rotor inlet. This high Mach number is intended to attenuate forward noise at both the design-speed takeoff point, and at the unconventional low-pressure-ratio, design-speed approach point. As speed was increased near design, all forward noise components were reduced, and rear noise in the discharge duct was increased, indicating that the high Mach number flow at the rotor face is attenuating forward noise at takeoff. The fan at takeoff is some 5.5 to 11 dB quieter than several reference fans. Data at the point closest to approach indicated tentatively that the design-speed approach mode was 3 dB quieter than the conventional mode.

Lucas, J. G.↗
NASA NTRS1982

Dynamic analysis of turbulent annular seals based on Hirs' lubrication equation

Expressions are derived which define dynamic coefficients for high-pressure annular seals typical of neck-ring and interstage seals employed in multistage centrifugal pumps. Completely developed turbulent flow is assumed in both the circumferential and axial directions, and is modeled in this analysis by Hirs' turbulent lubrication equations. Linear zeroth and first-order 'short-bearing' perturbation solutions are developed by an expansion in the eccentricity ratio. The influence of inlet swirl is accounted for in the development of the circumferential flow field. Comparisons are made between the stiffness, damping, and inertia coefficients derived herein based on Hirs' model and previously published results based on other models. Finally, numerical results are presented for interstage seals in the Space Shuttle Main Engine High Pressure Fuel Turbopump and a water pump.

Childs, D. W.↗