Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “3D PRINTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Cryogenic goniometer for measurements in pulsed magnetic fields fabricated via additive manufacturing technique

Complex high-precision mechanical devices can be fabricated using 3-dimensional printing technology with the help of computer-aided design. Using 3D stereolithography, we have constructed a cryogenic goniometer for measurements in pulsed magnetic fields of up to 100 T, at temperatures as low as 0.5 K. We review the properties of several materials tested in developing the goniometer and report on its design and performance. The goniometer allows samples to be rotated in situ to a precision of 0.2 deg, so that the field can be applied at many different angles to the samples’ symmetry directions. Following its success, we establish that 3D printing is now a viable technology for pulsed-field and other cryogenic probes.

3D printing↗
DOE OSTI2025

High‐Speed Embedded Ink Writing of Anatomic‐Size Organ Constructs

Embedded ink writing (EIW) is an emerging 3D printing technique that fabricates complex 3D structures from various biomaterial inks but is limited to a printing speed of ∼10 mm s −1 due to suboptimal rheological properties of particulate-dominated yield-stress fluids when used as liquid baths. In this work, a particle-hydrogel interactive system to design advanced baths with enhanced yield stress and extended thixotropic response time for realizing high-speed EIW is developed. In this system, the interactions between particle additive and three representative polymeric hydrogels enable the resulting nanocomposites to demonstrate different rheological behaviors. Accordingly, the interaction models for the nanocomposites are established, which are subsequently validated by macroscale rheological measurements and advanced microstructure characterization techniques. Filament formation mechanisms in the particle-hydrogel interactive baths are comprehensively investigated at high printing speeds. To demonstrate the effectiveness of the proposed high-speed EIW method, an anatomic-size human kidney construct is successfully printed at 110 mm s −1 , which only takes ∼4 h. This work breaks the printing speed barrier in current EIW and propels the maximum printing speed by at least 10 times, providing an efficient and promising solution for organ reconstruction in the future.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Additive Manufacturing of Heat Pipes for Microreactor Applications

Heat pipes are highly effective devices used to passively transport heat by two-phase capillary action. Their small footprint, light weight and lack of moving parts make them ideal for transportable nuclear microreactors, where size and weight are limited, minimal to no operation and maintenance are required, and high reliability is desired. The use of additive manufacturing allows for the fabrication of heat pipes with performance enhancements, such as microchannels, grooves, arteries, or tailored porosity, which are difficult, expensive or impossible to achieve with traditional fabrication techniques. We are evaluating the capabilities of the Admaflex 130 Digital Light Printer to produce these geometries by characterizing feature shrinkage, developing an optimal heat treatment recipe, assessing the effects of heat treatment atmosphere and varying print orientation. Computational simulations are being used to estimate performance of the various 3D printed configurations.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Interpenetrated Structures for Enhancing Ion Diffusion Kinetics in Electrochemical Energy Storage Devices

The architectural design of electrodes offers new opportunities for next-generation electrochemical energy storage devices (EESDs) by increasing surface area, thickness, and active materials mass loading while maintaining good ion diffusion through optimized electrode tortuosity. However, conventional thick electrodes increase ion diffusion length and cause larger ion concentration gradients, limiting reaction kinetics. We demonstrate a strategy for building interpenetrated structures that shortens ion diffusion length and reduces ion concentration inhomogeneity. This free-standing device structure also avoids short-circuiting without needing a separator. The feature size and number of interpenetrated units can be adjusted during printing to balance surface area and ion diffusion. Starting with a 3D-printed interpenetrated polymer substrate, we metallize it to make it conductive. This substrate has two individually addressable electrodes, allowing selective electrodeposition of energy storage materials. Using a Zn//MnO 2 battery as a model system, the interpenetrated device outperforms conventional separate electrode configurations, improving volumetric energy density by 221% and exhibiting a higher capacity retention rate of 49% compared to 35% at temperatures from 20 to 0 °C. Our study introduces a new EESD architecture applicable to Li-ion, Na-ion batteries, supercapacitors, etc.

25 ENERGY STORAGE↗
DOE OSTI2024

System and method for in situ volumetric sensing of 3D cure state of resin being used in an additive manufacturing system

An in situ cure monitoring control system for use with a volumetric three dimensional (3D) printing system, wherein the volumetric 3D system includes a container defining a build volume, the container includes a photocurable resist used for making a 3D part, and the resist is responsive to an optical curing beam from a light source, which is controlled by a controller, and which is passed through the resist. The cure monitoring control system includes an optical signal source which generates optical signals having a wavelength selected in relation to a characteristic of the resist, and directed to pass through the build volume. A detector detects the optical signals and generates output signals in accordance therewith. Software monitors the output signals and uses the output signals to modify the curing beam to help optimize curing of the resist.

Panas, Robert Matthew↗
DOE OSTI2021

All-in-one bipolar electrode: A new concept for compact and efficient water electrolyzers

Highly compact and efficient proton exchange membrane electrolyzer cells (PEMECs) are strongly desired for commercializing hydrogen production. Here, a novel concept of all-in-one bipolar electrode (AIOBE) is proposed for high-efficiency and compact PEMECs with the help of 3D printing and sputtering coating. AIOBE ideally integrated catalyst layer (CL)/gas diffusion layer/bipolar plate/current distributor/gasket, which significantly reduced component quantity on the cathode side of PEMECs from 5 to 1, cut down on part weight and volume, and drastically accelerated the fabrication and maintenance processes. Moreover, AIOBE with the micro-scale flat surface and nano-scale rough CL provided an ultralow ohmic resistance (~100 mOhm cm 2 ) and a high catalyst utilization. Finally, AIOBE delivered a practical voltage of 1.62 V and a high energy efficiency of 91% at 1000 mA/cm 2 , and its mass activity (4.48 A/mg Pt ) was 14 times higher than conventional PEMECs. In conclusion, this work provides a new route for developing highly compact electrochemical devices, such as fuel cells, electrolyzers for N 2 reduction and CO 2 conversion, and many more.

3D printing↗
DOE OSTI2025

Spatially programmed alignment and actuation in printed liquid crystal elastomers

Liquid crystal elastomers (LCEs) exhibit reversible shape morphing behavior when cycled above their nematic-to-isotropic transition temperature. During extrusion-based 3D printing, LCE inks are subjected to coupled shear and extensional flows that can be harnessed to spatially control the alignment of their nematic director along prescribed print paths. Here, we combine experiment and modeling to elucidate the effects of ink composition, nozzle geometry, and printing parameters on director alignment. From rheological measurements, we quantify the dimensionless Weissenberg number ( Wi ) for the flow field each ink experiences as a function of printing conditions and demonstrate that Wi is a strong predictor of LCE alignment. We find that director alignment in LCE filaments printed through a tapered nozzle varies radially when Wi < 1, while it is uniform when Wi ≫ 1. Based on COMSOL simulations and in operando X-ray measurements, we show that LCE inks printed through nozzles with an internal hyperbolic geometry exhibit a more uniform director alignment for a given Wi compared to those through tapered nozzles. Concomitantly, the stiffness along the print direction and actuation strain of printed LCEs increases substantially under such conditions. By varying Wi during printing through adjusting the flow rate “on the fly”, LCE architectures with uniform composition, yet locally encoded shape morphing transitions can be realized.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A New Method for Creating Structured High-Performance Current Collectors for Electrochemical Applications

A significant challenge in many electrochemical systems is finding a stable, high-performing current collector material that is mechanically robust, adaptable in form factor, and free of precious metals. Titanium electrodes are robust in many of these regards but exhibit poor charge transfer performance due to self-passivation. Herein, a new materials processing paradigm based on the titanium/titanium nitride (Ti/TiN) system which allows for robust, stable, and low-resistance current collectors of arbitrary form factor is presented. Specifically, a gas-nitriding process for 3D-printed titanium electrodes that results in a 20-fold improvement of charge transfer characteristics relative to the untreated material is outlined. The ability to utilize 3D-structured current collectors with a net 40-fold improvement in performance over nonstructured electrodes is further demonstrated. This novel approach to creating electrochemical current collectors requires minimal laboratory resources and can be widely adapted for a variety of applications, including desalination, electrolysis, energy storage, and basic research. In conclusion, the work described herein provides both a means for accelerating research and opens the door to hierarchical tuneability for enhanced performance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Fabric controls on fracture surface roughness of an architected rock material

Fluid flow through fractures is intimately linked to the fracture surfaces that define the void geometry through which fluids flow. Thus, an understanding of what controls fracture surface roughness is essential to the development of models for predicting fluid transport through fractured rock. The difficulty in predicting surface roughness arises from the complexity of rock which is inherently heterogeneous and nonuniform in composition, fabric, and structural components, even when samples are acquired from the same rock mass. Here, a benchmarked-simulation approach motivated from geo-architected 3D printed synthetic gypsum rocks is used to provide insight into the competing contributions from fabric and layering on fracture roughness formation. Simulation results from a discrete element model (Particle Flow Code, Itasca Consulting Group, Inc.) clearly indicate that the relative orientation between mineral layers and in-layer mineral fabric, and the variability in mineral bonding strengths determine whether anisotropic corrugated surfaces or isotropic surfaces are formed. Weak mineral layers oriented perpendicular to the applied load resulted in strong roughness anisotropy. Peak failure loads were found to vary up to 30% depending on the strength of the mineral fabric at the location of fracture initiation, which provides insight into the observed high variability in strength values of natural rock. The uniqueness of induced fracture roughness and peak failure load is intimately linked to layering, mineral fabric, and their distribution in the rock. These findings have important implications for any architected material fabricated through serial printing of layers with local compositional heterogeneity.

3D printed rock↗
DOE OSTI2025

Lab-scale Production of Coal-derived Graphene Particle Bonded Filaments

The main goal of the project was to develop a lab-scale manufacturing process to fabricate filaments with high carbon content for Fused Deposition Modeling (FDM) three-dimensional (3D) printing use. Graphene particles derived from domestic US coal waste was used as feedstock for filament development.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Carbonic Anhydrase Enhanced UV-Crosslinked PEG-DA/PEO Extruded Hydrogel Flexible Filaments and Durable Grids for CO 2 Capture

In this study, poly (ethylene glycol) diacrylate/poly (ethylene oxide) (PEG-DA/PEO) interpenetrating polymer network hydrogels (IPNH) were extruded into 1D filaments and 2D grids. The suitability of this system for enzyme immobilization and CO 2 capture application was validated. IPNH chemical composition was verified spectroscopically using FTIR. The extruded filament had an average tensile strength of 6.5 MPa and elongation at break of 80%. IPNH filament can be twisted and bent and therefore is suitable for further processing using conventional textile fabrication methods. Initial activity recovery of the entrapped carbonic anhydrase (CA) calculated from esterase activity, showed a decrease with an increase in enzyme dose, while activity retention of high enzyme dose samples was over 87% after 150 days of repeated washing and testing. IPNH 2D grids that were assembled into spiral roll structured packings exhibited increased CO 2 capture efficiency with increasing enzyme dose. Long-term CO 2 capture performance of the CA immobilized IPNH structured packing was tested in a continuous solvent recirculation experiment for 1032 h, where 52% of the initial CO 2 capture performance and 34% of the enzyme contribution were retained. These results demonstrate the feasibility of using rapid UV-crosslinking to form enzyme-immobilized hydrogels by a geometrically-controllable extrusion process that uses analogous linear polymers for both viscosity enhancement and chain entanglement purposes, and achieves high activity retention and performance stability of the immobilized CA. Potential uses for this system extend to 3D printing inks and enzyme immobilization matrices for such diverse applications as biocatalytic reactors and biosensor fabrication.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

An innovative carbonated cementitious material and its printability and carbon mineralization capacity

The main goal of this research is to develop a carbonated cementitious material (CCMs) mix design and demonstrate its rapid stiffening for manufacturing 3D printed or precast elements for building construction (i.e., concrete with enhanced durability and CO 2 capture efficiency). The material development employs hydrated Ca(OH) 2 , and its distinct reaction with CO 2 to form CaCO 3 . Different formulations and additives including polymer materials enable the thermomechanical properties that give these CCMs 3D printability comparable with cement materials used for similar applications. Here, printable and castable CCM formulations were successfully developed and demonstrated to mineralize CO 2 to form up to 57% CaCO 3 .

36 MATERIALS SCIENCE↗
DOE OSTI2022

Affordable Artificial Intelligence-Assisted Machine Supervision System for the Small and Medium-Sized Manufacturers

With the rapid concurrent advance of artificial intelligence (AI) and Internet of Things (IoT) technology, manufacturing environments are being upgraded or equipped with a smart and connected infrastructure that empowers workers and supervisors to optimize manufacturing workflow and processes for improved energy efficiency, equipment reliability, quality, safety, and productivity. This challenges capital cost and complexity for many small and medium-sized manufacturers (SMMs) who heavily rely on people to supervise manufacturing processes and facilities. This research aims to create an affordable, scalable, accessible, and portable (ASAP) solution to automate the supervision of manufacturing processes. The proposed approach seeks to reduce the cost and complexity of smart manufacturing deployment for SMMs through the deployment of consumer-grade electronics and a novel AI development methodology. The proposed system, AI-assisted Machine Supervision (AIMS), provides SMMs with two major subsystems: direct machine monitoring (DMM) and human-machine interaction monitoring (HIM). The AIMS system was evaluated and validated with a case study in 3D printing through the affordable AI accelerator solution of the vision processing unit (VPU).

3D printing↗
DOE OSTI2022

Volatile organic compound emissions from 4D printing: Effects of material composition and external stimulus

4D printing of stimuli-responsive materials extends 3D printing by enabling the fabricated structures to transform their shapes and properties over time in response to external stimuli. Numerous research efforts have been dedicated to developing new smart materials, enhancing material printability, and ensuring time-evolving properties. Meanwhile, the use of smart materials and external stimuli in 4D printing has introduced the possibility of air emissions that can potentially deteriorate the indoor air quality at the workplace and pose continuous health hazards to users during the production and use phases. These potential air emissions caused by 4D printing have not yet been assessed in current literature, leading to unknown occupational hazards and human health effects. This study focuses on stereolithography-based 4D printing with constrained thermo-mechanics and builds an emission model to quantify the volatile organic compound emissions from printing, shape programming, and shape recovery stages. The established model mathematically links the emission characteristics with material compositional design and stimuli-response mechanisms. Additionally, shape fixity and recovery abilities are considered to analyze the trade-off between the air emissions and stimuli-response performance of 4D printed parts. Case study results suggest that the methacrylate-based thermo-responsive material with higher glass transition temperature leads to higher air emissions, surpassing the permissible exposure level in the indoor environment. By altering the thermo-temporal conditions, a 61.29% reduction in emission yield can be achieved while ensuring a satisfactory shape memory performance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Reconfigurable plasma-dielectric hybrid photonic crystal as a platform for electromagnetic wave manipulation and computing

The introduction of 3D printing has enabled fabrication of photonic crystal devices with complex crystal structures that would be challenging to construct using other fabrication methods. In this paper, we construct and characterize a photonic crystal consisting of two 4 x 8 x 8 cubic lattices composed of spherical silicon nitride elements straddling a layer of 8 plasma discharge tubes, creating a 3D hybrid plasma photonic crystal device. Integrating under-dense gaseous plasma elements provides a unique coupling dynamic between the dielectric spheres and the cylindrical plasma discharges, creating a monolithic hybrid photonic crystal with solid state and reconfigurable elements. The device has resonant modes that have attenuation peaks that are either switchable, tunable in amplitude, or tunable in frequency with variations in plasma density. The response of these bands seen with varying plasma density is confirmed through simulations when effects due to the heating of the photonic crystal from the gaseous plasma elements are accounted for in the experiments. We discuss how this reconfigurable device may be used and expanded upon for applications in photonic artificial neural networks and optical computing systems.

3D printing↗
DOE OSTI2020

Prototyping of N95 Respirators Using Additive Manufacturing NETL NLVB (Final Report)

Final report for National Energy Technology Laboratory (NETL) project involving the use of advanced manufacturing and 3D printing technologies to help address personal protective equipment (PPE) shortages due to COVID-19. Work was performed in support of Joint DOE Laboratory Plan for Manufacturing Medical Supplies and funded through the DOE Office of Science.

3D Printing↗
DOE OSTI2024

Block Polyelectrolyte Additives That Modulate the Viscoelasticity and Enhance the Printability of Gelatin Inks at Physiological Temperatures

We demonstrate the utility of block polyelectrolyte (bPE) additives to enhance viscosity and resolve challenges with the three-dimensional (3D) printability of extrusion-based biopolymer inks. The addition of oppositely charged bPEs to solutions of photocurable gelatin methacryloyl (GelMA) results in complexation-driven self-assembly of the bPEs, leading to GelMA/bPE inks that are printable at physiological temperatures, representing stark improvements over GelMA inks that suffer from low viscosity at 37 °C, leading to low printability and poor structural stability. The hierarchical microstructure of the self-assemblies (either jammed micelles or 3D networks) formed by the oppositely charged bPEs, confirmed by small-angle X-ray scattering, is attributed to the enhancements in the shear strength and printability of the GelMA/bPE inks. Varying bPE concentration in the inks is shown to enable tunability of the rheological properties to meet the criteria of pre- and postextrusion flow characteristics for 3D printing, including prominent yielding behavior, strong shear thinning, and rapid recovery upon flow cessation. Moreover, the bPE self-assemblies also contribute to the robustness of the photo-cross-linked hydrogels; photo-cross-linked GelMA/bPE hydrogels are shown to exhibit higher shear strength than photo-cross-linked GelMA hydrogels. Last, the assessment of the printability of GelMA/bPE inks indicates excellent printing performance, including minimal swelling postextrusion, satisfactory retention of the filament shape upon deposition, and satisfactory shape fidelity of the various printed constructs. We envision this study to serve as a practical guide for the printing of bespoke extrusion inks where bPEs are used as scaffolds and viscosity enhancers that can be emulated in a range of photocurable precursors.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Grid Resilient, Self-Powered, Fuel Flexible, High Efficiency Heating System (Final Report)

The Grid Independent High Efficiency System (GIHES) delivers a heating system that operates free from the power grid and provides ultra-low emissions and high efficiency heating for residential and commercial buildings. The project demonstrated two weeks of continuous grid independent operation of a storage water heater equipped with a powered damper. The Thermoelectric Generator (TEG) integrated GIHES technology revolutionizes heating systems to provide grid resilient hot water production, while delivering significant value to the end user by eliminating impacts of power interruption and enhancing comfort, convenience and productivity. The system maximizes the thermal-to-electric conversion efficiency by optimizing location and orientation of the TEGs and durability while lowering system costs. The TEGs generate enough power to charge a battery and run the storage water heater unit with a powered damper uninterrupted by providing the required parasitic electrical power for start-up, shutdown and during idling. Several TEGs were analytically and experimentally evaluated based on the size, surface area and the power being generated before designing and fabricating a complete multi-TEG assembly for integration with the water heater. The GIHES technology can be extended to boilers, furnaces and tankless water heaters and integrated with heat pump to further increase the overall equipment efficiency. The technology has the potential to reduce the amount of dispatch power and peak power plant operation. An advanced burner was designed, developed and 3D printed for fuel flexible operation. The burner was designed to enable tighter integration with TEGs for potentially higher TEG output, should this be necessary. A bench-scale test rig to perform testing of a 200,000 Btu/h burner and capable of handling up to 10% H2 (by volume) was setup at GTI’s laboratory with appropriate safety and controls to ensure smooth and safe operation. Testing of the 3D burner showed < 5 ppm NOx emissions can be achieved for the entire firing range and with different levels of hydrogen blends with natural gas. The burner will enable a more integrated TEG-burner module design for improved system performance, should this be required in the future. Techno-economic analysis (TEA) of the TEG integrated with the water heaters was performed. The testing data and the power output were used to develop the TEA. The analysis for the storage unit with damper showed that the TEG integrated system costs $95. This is much lower than a one-time charge needed to wire and install dedicated power. Discussions with TEG manufacturers and OEM’s will provide more detailed information and methods to further lower these costs.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗