Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Effect of Surface Self-Nanocrystallization on Diffusion Bonding Between a Titanium Alloy and a TiAl-Based Alloy

A self-nanocrystallization layer was prepared on the surface of a Ti alloy sample via shot peening to investigate its influence on the follow-up diffusion bonding between a titanium alloy and a TiAl-based alloy. The experiment results show that surface self-nanocrystallization treatment can accelerate the interface reaction between a Ti alloy and a TiAl alloy, lowering the bonding temperature of the sound joints by more than 50 K. Moreover, the thickness of the interface reaction layer plays an important role in the interfacial bonding strength. In this work, the maximum shear strength of the joint appears to have a thickness of about 1.8 μm. As a consequence, it is found that surface self-nanocrystallization treatment is helpful for optimizing the diffusion bonding process.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

The Effect of Surface Condition on Wetting of HASTELLOY{sup ®} X by Brazing Filler Metal of Ni-Pd-Cr-B-Si System

The paper presents the results of wettability tests by a sessile drop method coupled with residual gas analysis for the HASTELLOY{sup ®} X substrates contact heated with brazing filler metal of Palnicro 36M. The contact angles formed between the substrate and the molten brazing filler metal were recorded by high-speed high-resolution CCD camera using two different heating procedures: (1) fast continuous heating to a temperature of 960 °C; (2) isothermal heating at a temperature of 995 °C for 10 min after step heating to the test temperature. In this study, the reference sample was HASTELLOY{sup ®} X in a delivery state (D1). The base material with a different surface finish was also tested: after polishing (P1), after polishing and oxidation at a temperature of 600 °C for 1 h in the air (U1). The tests confirmed very good wetting properties of Palnicro 36M on HASTELLOY{sup ®} X, independently on its surface finish and the heating procedure used in this study, i.e., after 10 min at 995 °C, the final contact angle values were θ{sub f} = 7.6 ± 0.1°, 6.03 ± 0.07° and 6.2 ± 1.0° for D1, P1 and U1, respectively. However, oxidation of HASTELLOY{sup ®} X surface affects the wetting kinetics and spreading of molten Palnicro 36M on BM substrates by: (1) increasing the initial contact angle values (θ{sub 0} = 51 ± 4°, 65 ± 13° and 83 ± 2° for D1, P1 and U1, respectively), (2) delaying the wetting process and (3) reducing the spreading area since after wettability tests at 960 °C, the largest area covered with solidified Palnicro 36M drop was noted for D1 (92 mm{sup 2}) while the smallest one for U1 (52 mm{sup 2}).

36 MATERIALS SCIENCE↗

Efficient Pd on carbon catalyst for ammonium formate dehydrogenation: Effect of surface oxygen functional groups

Formate solution is one of a kind promising liquid organic hydrogen carrier but suffers from kinetic challenges. This study investigates the kinetics of the surfacefunctionalized Pd on carbon catalysts for formate dehydrogenation and the impact of O-functional groups. Here, the fraction of the distinguished O-functional groups was modulated by the different concentrated HNO 3 solutions treatment or by H 2 reduction. This study shows that the O-functional groups play critical roles in dispersing Pd nanoparticles and decreasing the activation energy for dehydrogenation. Density functional theory (DFT) calculation reveals that most O-functional groups enhance formate adsorption on the Pd active site. However, the existence of C=O groups consumes reducing agents and hinders the formation of metallic Pd. The electron transfer from Pd to oxygen functional groups is unfavorable to dehydrogenation. The as-prepared Pd5/re-ACA (reduced activated carbon washed by acid) exhibited significant activity with a higher turnover frequency of 13,511 h -1 than commercial Pd/C.

54 ENVIRONMENTAL SCIENCES↗

Capacitive Deionization Using Alternating Polarization: Effect of Surface Charge on Salt Removal

Alternating polarization (AP) at ±1.2/0 V is performed on a capacitive deionization stack assembled with carbon xerogel (CX) electrodes. Long-term testing shows enhanced cycling stability without the formation of inversion peaks. AP also leads to an arch-shaped plot of salt adsorption capacity (SAC) versus cycling time, with the highest SAC of approximately 3 mg (NaCl) g −1 (CX) during this long-term test. Characterization of both the freshly prepared and cycled electrodes depict that AP results in surface charge of all the electrodes being modified from positive to negative character. Here by leveraging balances of electronic, surface, and ionic charges in carbon micropores, it is found that a portion of the electronic charge contributes to the ionic charge for salt adsorption, and another portion is parasitically consumed to balance the surface charge during the charge reconciliation process. When the consumption of electronic charge for charge reconciliation becomes minimal, both the positive and negative surface charges are nearly equivalent on the CX electrode. Under such a condition, the highest SAC values can be achieved for AP testing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Experimental and theoretical investigations on the adherent behaviors of high viscosity liquid: The effect of surface topography

Wetting test and classical molecular dynamics (MD) simulations were employed to investigate the adherent behaviors of hydroxyl-terminated polybutadiene (HTPB), a typical high viscosity liquid widely used as a binder in rocket motor propellants, onto the copper (Cu) surfaces with different topographies. Experimental data show that the microstructures protruding above the substrate surfaces can be ‘sensed’ by the HTPB droplet, which has been indicated by the smaller contact angles and higher interface tension for this specific liquid on the rough surfaces (featured with sinusoidal structures or square pillars) than that on the smooth surface. Simulation results reveal the atomic details of spreading process of HTPB chains, with diverse diffusion propensities presented on different surfaces. The HTPB droplet spreads widely on the smooth surface, exhibiting a roughly isotropic trend. On the contrary, the state of this high viscosity liquid on the sinusoidal-structured surface is featured by wide contact diffusion along the run of groove, but relatively restricted extension in the direction perpendicular to the groove, as a result of the barriers exerted by the nearest neighbouring peaks. The existence of nanoscale pillars increases the exterior surface area of Cu substrate, therefore the HTPB chains can penetrate deep to envelop the peripheries of the pillars, forming abundant direct contacts with Cu surface and producing a highest HTPB–Cu interaction energy, which well accords with the experimental results about the adherent strength of HTPB.

Wu, Chunya↗

Experimental investigation on the effect of surface electric field in the growth of tungsten nano-tendril morphology due to low energy helium irradiation

The mechanisms responsible for and controlling the growth of tungsten nano-tendrils (or “fuzz”) under low-energy helium plasma exposure remain unclear. For the first time in nano-tendril experiments, the plasma sheath-produced electric field and the helium (He) ion energy have been decoupled, showing that the sheath electric field has little impact on nano-tendril growth, eliminating a possible cause for tendril growth. The well-established necessary growth conditions for W fuzz were maintained with He ion flux density Γ He > 10 21 He m –2 s –1 , surface temperature T s = 1273 K, He ion energy E He = 64 eV, and He ion fluence Φ He > 10 24 He m –2 . A grid is situated between the tungsten sample and plasma, with the grid and sample potentials independently controlled in order to control the electric field at the surface of the sample while maintaining the same incident He ion energy to the surface. A calculation of the potential profile in the drift space between the grid and sample was used to account for space charge and calculate the electric field at the surface of the sample. Tungsten fuzz formed at all electric fields tested, even near zero electric field. Also, the depth of the resulting W fuzz layer was unaltered by the electric field when compared to the calculated depth determined from an empirical growth model. The conclusion is that the sheath electric field is not necessary to cause the changes in surface morphology.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗