SEARCH · Engineering Papers

Results for “sprays”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Fabrication of high-performance gas-diffusion-electrode based membrane-electrode assemblies

This paper demonstrates the fabrication and processing steps required to produce high performance fuel cell membrane electrode assemblies (MEAs) based on spray-coated gas-diffusion electrodes (GDEs). It is demonstrated that coating the catalyst layer with a thin layer of ionomer and then hot pressing the GDEs to the membrane is required to achieve comparable catalyst activity and air performance to catalyst-coated-membrane MEAs. We show that there is a critical amount of ionomer required to achieve maximized performance. Using electron microscopy, we show that the combination of the ionomer overlayer and hot-pressing bonds the catalyst layer to the membrane, increasing the interfacial contact area and quality of this interface. We also find that the ionomer overlayer smooths the surface of the GDE and provides increased contact area between the GDE and the membrane. Additionally, we demonstrate that much less ionomer is required for high-performance than has been previously reported. Through model fitting of electrochemical impedance spectroscopy, we show that this improvement in the catalyst layer - membrane interface reduces the effective catalyst layer resistance, which reduces Ohmic losses and increases catalyst utilization.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2021

Scaleup and manufacturability of symmetric-structured metal-supported solid oxide fuel cells

Metal-supported solid oxide fuel cells with symmetric architecture, having metal supports on both sides of the cell, are scaled up from button cell size to large 50 cm 2 active area cell size. The cells remain flat after sintering assisted by the symmetric structure. Equivalent performance is achieved for button cells and large cells, and thermal cycling and redox cycling tolerance are demonstrated for the large cells. The catalyst infiltration process is improved to enable high-throughput manufacturing. The cumbersome lab-scale molten nitrate infiltration process is replaced with a room-temperature process in which a shelf-stable aqueous solution of nitrate salts is applied to the cell by spraying, painting, or other scalable techniques. Here, a fast-ramp thermal conversion of the nitrate salts to the final oxide catalyst composition is implemented, allowing many infiltration cycles to be accomplished in a single work shift. Increasing the number of infiltration cycles from 5 to 10 led to an increase in peak power density from approximately 0.3 to 0.52 W cm -2 .

25 ENERGY STORAGE↗

DOE OSTI2022

Modeling deformation and failure in AlSi-polyester abradable sealcoating material using microstructure-based finite element simulation

A plasma-sprayed aluminum-silicon (AlSi)/polyester coating is applied in modern gas turbine engines as an abradable sealcoating to maintain tight clearances between the rotating blades and the static casing. While running the engine, the rotating blades “rub” with the abradable coating, which results in extreme strain rate (up to 10 6 ) dynamics and a high-temperature environment. Due to the difficulty of collecting direct measurements, predictive computational models are important for analyzing the deformation and failure of the abradable material, to help meet the design target of avoiding damage to the blade tip and maintaining high fuel efficiency. In this research, a microstructure-based finite element (FE) computational model was developed to capture the complex mechanical behavior of the AlSi/polyester microstructure. The model is based on a virtual representative-volume-element (RVE) of a metal-polymer microstructure, reconstructed from x-ray computed tomography. It models the plastic deformation of, and damage to, each AlSi and polyester constituents, as well as the failure at their interface. The model was calibrated and validated with uniaxial tension and compression experiments, conducted at two temperatures (298 K and 533 K) at an applied strain rate of 10 3 - 10 4 s -1 . The material exhibited strongly asymmetric tension-compression behavior and a sensitivity to temperature, which was well captured by the model. The model was further applied to investigate changes in mechanical behavior due to variations in constituents’ volume fractions, which provides guidance to the microstructural design of AlSi/polyester abradable materials. The model is expected to facilitate the development of improved abradable materials by bypassing the conventional trial-and-error approach and extensive testing requirements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Stable electrospray signal on a microfabricated glass chip with three-dimensional open edge and tiered depth geometries

This paper presents the microfabrication and performance of a three-dimensional electrospray ionization (ESI) emitter tip made from glass, which achieves stable current signals important for chemical analysis. Our novel microfabrication process and custom-built signal conditioning hardware provides the advantage of providing accurate features and steady signals. The fabrication process relies on standard microfabrication techniques (i.e., deposition, photolithography, and wet etching). This fabrication method involves the novel application of two layers of positive and negative photoresists in addition to Parafilm® wax tape. Open edge and tiered depth details were successfully created from a multilayer planar mask. This is a benefit for integrated miniaturized and microfluidic systems that often require micro features for their functionality but relatively large millimeter size features for their physical periphery. We demonstrate the fundamental performance of electrospray with this microfluidic chip. The emitter tip was fixed on a linear axis stage with high resolution (10 μm) to finely control the tip distance from a metal counter electrode plate. Further, a custom printed circuit board system was built to safely control four voltages applied to the microchip ports from a single high voltage power supply. To readily form the electrospray, non-aqueous solvents were used for their low viscosity and a constant voltage of +2.7 kV was applied to the sheath electrospray microchannel. The liquid being sprayed was 80/20 (v/v) methanol/acetonitrile with 0.1% acetic acid in the sheath microchannel and with ammonium acetate (10–40 mM) in its remaining microchannels. The electrospray signal was measured in response to varying the distance (1.4 to 1.6mm) between the electrospray emitter tip and a metal counter electrode plate in addition to the varying concentration of the background electrolyte, ammonium acetate. Stable and repeatable electrospray signal showed linear relationships with emitter tip distance and concentration (r 2 ≥ 0.95).

42 ENGINEERING↗

DOE OSTI2020

Additive manufacturing of soft and hard magnetic materials used in electrical machines

Soft and hard magnetic materials were fabricated using additive manufacturing (AM) for use in 3D electrical machines. The effect of the characteristics and the nature of the magnetic feedstock powders was evaluated for both the cold spray (CS) and the fused filament fabrication (FFF) processes. 3D finite element analysis (FEA) was used to develop new motor topologies based on the advantages offered by AM. FEA optimization also allowed the identification of the most critical material properties and is thus a powerful tool to facilitate material development.

Bernier, Fabrice↗

DOE OSTI2021

Hydrogen permeability and stability of palladium films in a high pressure reactor

Palladium (Pd) thin films were fabricated by colloidal spray deposition (CSD) on substrates of porous yttrium stabilized zirconium oxide (YSZ). The films were sintered at 1140–1160 °C for 2–3 h in argon and had thickness of 5–11 μm. The hydrogen (H 2 ) permeation flux for the Pd film was measured with simulated feed gases (90% H 2 /He, syn-gas/steam, or syn-gas/steam with H 2 S) flowing on the film side and sweep gas (Ar) flowing on the substrate side. Here, the hydrogen flux with the Pd film was obtained by adjusting the flow rate and pressure of the gas. Hydrogen flux values of 121–173 cm 3 min -1 cm -2 were measured at 388–596 °C (feed: 90% H 2 /He at 200 mL min -1 ; sweep: Ar at 1400 mL min -1 ; and ΔP = ~170 psi), and the permeability was calculated and compared with literature values. Because Pd is known to be sensitive to some gases, the stability of Pd films was evaluated by examining the microstructures of samples after their exposure to gas mixtures containing CO, CO 2 , H 2 O, and H 2 S. From the results of stability tests in H 2 S-containing atmospheres, the Pd/Pd 4 S phase boundary was determined, and this measured boundary was compared to the Pd/Pd 4 S boundary calculated from the thermodynamic data in the literature.

36 MATERIALS SCIENCE↗

DOE OSTI2020

High-efficiency, air-stable manganese–iron oxide nanoparticle-pigmented solar selective absorber coatings toward concentrating solar power systems operating at 750 °C

Solar selective absorber coating with long-term thermal stability at high temperatures ≥750 °C in air is an important component to reduce the levelized cost of energy (LCOE) of concentrating solar power (CSP) systems toward 50% power efficiency and dispatchable solar electricity. Conventionally, solar spectral selectivity requires multilayer-interference coatings implemented by stringently controlled vacuum deposition, and these coatings degrade significantly at >700 °C in air. Herein, we established a quantitative design approach and demonstrated a proof-of-concept air-stable, manganese–iron oxide nanoparticle (NP)-pigmented solar selective coatings with a high solar absorptance of ~93%, a relatively low thermal emittance of ~52%, and an optical-to-thermal energy conversion efficiency >89% under 1,000× solar concentration at 750 °C toward Generation 3 CSP systems. These coatings demonstrate spectral selectivity using cost-effective spray coating approach, a notable improvement over conventional vacuum-deposited, multilayer solar selective coatings for low-cost, high-efficiency solar thermal receivers. In contrast to the thermal degradation of spectrally non-selective benchmark Pyromark 2500 coatings at 750 °C in air, the solar absorptance of the MnFe 2 O 4 -pigmented coatings on stainless steel 310 (SS 310) substrates is increased to ~92.9% and the optical-to-thermal energy conversion efficiency is improved to 89.7% after serving at 750 °C in air for 700 h. X-ray diffraction results reveal that this improvement is due to the transformation of MnFe 2 O 4 NPs into more thermodynamically stable, non-stoichiometric manganese-rich manganese ferrite and iron-rich manganese–iron oxide phases after 500 h aging at 750 °C. For >1,000 h-endurance testing at 750 °C in air and the subsequent 19 day-night thermal cycling between 750 °C (12 h/cycle) and 25 °C (12 h/cycle) on SS 310 substrates, the thermal degradation is mainly due to the CrO x microflake formation from SS 310 substrates rather than the coatings, which can be suppressed by preoxidizing the surface of SS 310. With lower emittance matrix material and further optimization of pigment NP stoichiometry, concentration, and coating thickness, it is promising to achieve an optimized thermal efficiency ≥92.5% with long-term thermal stability at 750 °C for Generation 3 CSP systems.

14 SOLAR ENERGY↗

DOE OSTI2021

Utilizing the unique charge extraction properties of antimony tin oxide nanoparticles for efficient and stable organic photovoltaics

Simultaneously enhancing device performance and longevity, as well as balancing the requirements on cost, scalability, and simplification of processing, is the goal of interface engineering of organic solar cells (OSCs). In our work, we strategically introduce antimony (Sb 3+ ) cations into an efficient and generic n-type SnO 2 nanoparticles (NPs) host during the scalable flame spray pyrolysis synthesis. Accordingly, a significant switch of conduction property from an n-type character to a p-type character is observed, with a corresponding shift in the work function (WF) from 4.01 ± 0.02 eV for pristine SnO 2 NPs to 5.28 ± 0.02 eV for SnO 2 NPs with 20 mol. % Sb content (ATO). Both pristine SnO 2 and ATO NPs with fine-tuned optoelectronic properties exhibit remarkable charge carrier extraction properties, excellent UV resistance and photo-stability being compatible with various state-of-the-art OSCs systems. The reliable and scalable pristine SnO 2 and ATO NPs processed by doctor-blading in air demand no complex post-treatment. Our work offers a simple but unique approach to accelerate the development of advanced interfacial materials, which could circumvent the major existing interfacial problems in solution-processed OSCs.

14 SOLAR ENERGY↗

DOE OSTI2024

Intrinsically sodiophilic, mesoporous metal-free wetting layers based on inexpensive carbon black for sodium-metal batteries

In this article, elevated temperature molten Na batteries are seeing a resurgence of interest for low-cost electrochemical energy storage for the grid. Of the many recent innovations in this battery concept, new methods focused on intermediate temperature operation (e.g. 110–190 °C) have gained prominence as a way to enable comparable performance with less thermal energy loss and lower-cost materials of construction. However, the poor wettability of molten Na on suitable solid-electrolyte separators such as sodium Beta Alumina Solid-Electrolyte (Na-β”-Al 2 O 3 , ‘BASE’) requires continued innovation in interface engineering to promote full utilization of the solid-electrolyte surface area and minimize cell resistance. There have been many successful approaches to improve Na-wettability to-date including heat treatment in an inert atmosphere to remove adsorbed surface species, deposition of alloying metals such as Pb, Sn, or Bi, and use of carbon-based interfacial layers. However, these approaches either lack the ability to provide good wetting at very low temperatures (near the melting point of Na) or rely on non-scalable processes and/or toxic/expensive metals. To solve these issues, a new carbon-based sodiophilic treatment is demonstrated, which utilizes inexpensive components to form a meso/macroporous sodiophilic layer, is easily applied via drop-casting or spray-coating, provides excellent wetting as low as 110 °C, and is completely metal-free. It is found that the good sodium wetting can be attributed to the wider range of pore sizes in the carbon layers demonstrated in this study. Na wetting may occur as surface tension is initially broken by larger pores, followed by the intrusion of molten Na into smaller pores due to the apparent intrinsic affinity of Na-metal for carbon surfaces, in conjunction with the capillarity effect. Low cell-level area specific resistances of 20–30 and 13–15 Ω·cm 2 are demonstrated at 110 and 140 °C respectively. Finally, the utility of this metal-free wetting layer for solid-Na anodes is explored, showing that the metal-free wetting layer can reach a critical current density of 1.88 mA·cm -2 at 30 °C.

25 ENERGY STORAGE↗

DOE OSTI2025

Modeling of surface-state induced inter-electrode isolation of n -on- p devices in mixed-field and γ -irradiation environments

Position sensitive n-on-p silicon sensors will be utilized in the tracker and in the High Granularity Calorimeter (HGCAL) of the Compact Muon Solenoid (CMS) experiment at High Luminosity Large Hadron Collider (HL-LHC). The detrimental effect of the radiation-induced accumulation of positive net oxide charge on position resolution in n-on-p sensors has typically been countered by the application of isolation implants like p-stop or p-spray between n + -electrodes. In addition to the positively charged layer inside the oxide and close to the Si/SiO 2 -interface, surface damage introduced by ionizing radiation in SiO 2 -passivated silicon particle detectors includes the accumulation of trapped-oxide-charge and interface traps. A previous study of either n/γ (mixed field)- or γ-irradiated Metal-Oxide-Semiconductor (MOS) capacitors showed evidence of substantially higher introduction rates of acceptor- and donor-type deep interface traps (N it,acc/don ) in mixed-field environment. Here, in this work, an inter-pad and -strip resistance (or resistivity (ρ int )) simulation study of n-on-p sensors with and without p-stop isolation implants was conducted for both irradiation types. Higher levels of ρint showed correlation to higher densities of deep N it,acc/don , with the inter-pad isolation performance of the mixed-field irradiated sensors becoming independent of the presence of p-stop implant between the n + - electrodes up to about 100 kGy. The low introduction rates of deep N it,acc/don in γ-irradiated sensors resulted in high sensitivity of ρ int to the presence and peak doping of p-stop above the lowest dose of about 7 kGy in the study. As a consequence of the advantageous influence of radiation-induced accumulation of deep N it on the inter-electrode isolation, position sensitive n-on-p sensors without isolation implants may be considered for future HEP-experiments where the radiation is largely due to hadrons.

Akchurin, N. [Texas Tech Univ., Lubbock, TX (Unite↗

DOE OSTI2023

Progress towards the FRIB-EDM 3 -Frontend: A tool to provide radioactive molecules from isotope harvesting for fundamental symmetry studies

The under-construction FRIB-EDM 3 -instrument was designed to study polar radioactive molecules (such as RaF) in transparent cryogenic solids by laser spectroscopy. The instrument is divided into a frontend- and a backend section. The frontend accepts an aqueous sample from isotope harvesting and provides a mass-separated molecular ion beam in an ultra-high vacuum environment. In the backend, the ions are guided into alkali-metal vapor and the resulting neutrals are co-deposited in a solid argon matrix to perform laser spectroscopy. Here, this work addresses the frontend of the instrument. The efficient ionization of harvested radioisotopes from aqueous samples is achieved with a spray-ionization method. Subsequently, the molecular ion beam is analyzed by mass-to-charge ratio by a quadrupole mass filter. To verify the feasibility of the approach, numerical simulations with the COMSOL and SIMION packages have been conducted. While the former was applied to study transport in ion funnels, the latter was used to investigate ion beam transmission through the lower pressure sections. Following promising simulation results, a first experimental setup is under construction.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2026

Overview of advanced plasma-facing materials testing for Fusion Pilot Plants at DIII-D

Characterization and testing of advanced plasma-facing materials (PFMs) for Fusion Pilot Plants (FPP) is being conducted at the DIII-D National Fusion Facility through the ongoing two-year FPP Candidate Materials Thrust. Year one tested 17 novel materials utilizing the Divertor Materials Evaluation System (DiMES), with samples analyzed pre- and post-experiment via SEM, EDS, and confocal microscopy. Repeatable reference discharges were developed to ensure uniformity between experiments, including a new strike-point rastering scenario to provide more uniform heat/particle flux across DiMES during ELMing H-mode discharges. Various sample geometries and temperatures were used to achieve FPP-relevant conditions, including samples angled 10° towards the incident plasma flux and pre-heating up to 500 °C. The first exposure of liquid lithium (Li) capillary porous structures in a tokamak demonstrated uniform emission of Li vapor and suppression of Li droplets in H-mode when preheated to 350 °C. Dispersoid-strengthened W with 1 wt% TaC, TiC, and ZrC exposed to H-mode showed cracking and dispersoid ejection for all varieties except TiC, providing a clear down-selection. Ultra-high temperature ceramic materials TiB 2 and ZrB 2 showed minimal degradation under L-mode exposure. Silicon carbide (SiC) fiber composites showed arcing along edges, while CVD SiC remained pristine. Atmospheric plasma-sprayed W and SiC coatings endured H-mode exposure without macroscopic delamination; SiC exhibited granular ejection, while W showed increased outgassing. Additional W-based alloys were stress tested in H-mode, including Ni-based W heavy alloys, W f SiC f /W composites, W multi-principle element alloys, and functionally-graded W/SiC, to varying degrees of success.

DIII-D↗

DOE OSTI2020

Ion irradiation effects on Cr-coated zircaloy-4 surface wettability and pool boiling critical heat flux.

The concept of coating the currently used nuclear fuel cladding (zirconium-based alloy, typically Zircaloy-4 or Zirc-4) with an oxidation preventive layer is a progressing Accident tolerant Fuel (ATF) candidate alloys. The coated Zirc-4-based alloys could be a solution to suppress undesirable fast reaction kinetics with high-temperature steam. Zirc-4 has been the most preferred cladding material in pressurized water reactors (PWRs). Chromium (Cr) based alloys as a coating material provides excellent corrosion protection and good strength and wear resistance. In this paper, we present the surface wettability measurements and pool boiling Critical Heat Flux (CHF) for Cr-coated Zirc-4 claddings pre- and post-exposure to an ion irradiation environment. The wettability measurements, including static contact angle (contact angle, θ) and average surface roughness (surface roughness, Ra), are introduced for samples of different coating thicknesses (5–30 μm thick). The coatings fabricated by the cold spray of Cr-Al particles to 10 mm × 10 mm × 1.95 mm Zirc-4 substrates. Post fabrication, a Pilgering (cold rolling) process, was applied to finalize the coating thickness and resulted in a significant reduction in surface roughness of initially fabricated rough surfaces. The process produced three distinguished samples 5-μm unpolished (as machined), 5-μm, and 30-μm polished (cold rolled). The measurements are presented for the three surfaces and bare Zirc-4 as a baseline surface. The contact angle analyses were implemented in theoretical models from the literature to predict pool boiling CHF. Pool boiling experiments were conducted to measure the pool boiling CHF values and compare them to the predicted values. Scanning Electron Microscope (SEM) images and Energy Dispersive X-ray Spectroscopy (EDS) analysis was performed to characterize the surfaces for better understanding and interpreting the results. The SEM images showed localized surface damage due to ion irradiation. No recognized change in the measured surface roughness due to ion irradiation. The contact angles of irradiated Cr-coated surfaces are consistently higher (10°) than pre-irradiated surfaces. Decreasing the Cr-coating layer thickness resulted in lower contact angle pre- and post- ion irradiation. The predicted pool boiling CHF using the Kandlikar model is in good agreement with the experimentally measured CHF values within ±12% for all samples.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Ability of Particulate Matter Index to describe sooting tendency of various gasoline formulations in a stratified-charge spark-ignition engine

This study investigates the ability of Particulate Matter Index (PMI) to describe the sooting behavior of various gasoline formulations in a stratified-charge (SC) spark-ignition engine. Specifically, the engine was operated at 2000 rpm with an intake pressure of 130 kPa where soot formation is known to primarily occur in the bulk gases. Exhaust soot emissions were measured for nine test fuels at various exhaust gas recirculation levels. A comparison between measured soot levels and PMI shows that PMI is a relatively poor predictor of the sooting tendency of the tested fuels under lean SC combustion. Among the fuels, three fuels, namely the diisobutylene blend, High Olefin, and E30 fuels exhibit measured soot behavior opposite of that predicted by PMI. Optical diagnostics were utilized to further investigate the in-cylinder phenomena for these three fuels. Analysis of natural luminosity and diffused back-illumination extinction imaging suggests that fuel-induced differences in the amount of soot formed are responsible for a majority of the discrepancy in measured versus predicted sooting tendency. Fuel-induced differences in soot oxidation and spray development seem to play minor roles. Because the combustion and air-fuel mixing processes for lean SC combustion are different from conventional stoichiometric operation it is hypothesized that the PMI correlation needs to be modified to account for differences in stoichiometric air-fuel ratio and level of oxygenation between fuels. Furthermore, the role of fuel volatility in PMI possibly needs to be de-emphasized for SC operation with fuel injection into compression-heated gases.

42 ENGINEERING↗

DOE OSTI2024

Understanding the interplay between pilot fuel mixing and auto-ignition chemistry in hydrogen-enriched environment

The diesel-piloted dual-fuel compression ignition combustion strategy is well-suited to accelerate the decarbonization of transportation by adopting hydrogen as a renewable energy carrier into the existing internal combustion engine with minimal engine modifications. Despite the simplicity of engine modification, many questions remain unanswered regarding the optimal pilot injection strategy for reliable ignition with minimum pilot fuel consumption. The present study uses a single-cylinder heavy-duty optical engine to explore the phenomenology and underlying mechanisms governing the pilot fuel ignition and the subsequent combustion of a premixed hydrogen-air charge. The engine is operated in a dual-fuel mode with hydrogen premixed into the engine intake charge with a direct pilot injection of n-heptane as a diesel pilot fuel surrogate. Optical diagnostics used to visualize in-cylinder combustion phenomena include high-speed IR imaging of the pilot fuel spray evolution as well as high-speed HCHO* and OH* chemiluminescence as indicators of low-temperature and high-temperature heat release, respectively. Three pilot injection strategies are compared to explore the effects of pilot fuel mass, injection pressure, and injection duration on the probability and repeatability of successful ignition. The thermodynamic and imaging data analysis supported by zero-dimensional chemical kinetics simulations revealed a complex interplay between the physical and chemical processes governing the pilot fuel ignition process in a hydrogen containing charge. Hydrogen strongly inhibits the ignition of pilot fuel mixtures and therefore requires longer injection duration to create zones with sufficiently high pilot fuel concentration for successful ignition. Results show that ignition typically tends to rely on stochastic pockets with high pilot fuel concentration, which results in poor repeatability of combustion and frequent misfiring. In conclusion, this work has improved the understanding on how the unique chemical properties of hydrogen pose a challenge for maximization of hydrogen’s energy share in hydrogen dual-fuel engines and highlights a potential mitigation pathway.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2025

Analysis of soot formation from aviation fuels in laminar counterflow flames

Combustion emissions from aviation contribute to the formation of condensation trail (contrail) that can lead to the formation of anthropogenic cirrus clouds. Ice particles that form contrails are observed to have a linear correlation with soot particle number density. Synthetic aviation fuels (SAFs) offer a promising route to mitigate the production of soot particles while also increasing energy security. Although studies have focused on combustion and spray behavior, the detailed investigation of soot formation processes for different jet fuels and their impact on models for computational fluid dynamics (CFD) applications is not well understood. Moreover, experimental measurements of soot for canonical flames using Synthetic aviation fuels (SAF) for model validation remain scarce. To address this, we use employed the Lawrence Livermore National Laboratory (LLNL) detailed soot model based on the discrete sectional method. Additionally, we develop two reduced chemical mechanisms for Jet-A and Alcohol-to-Jet (C1) that are suitable for turbulent flame simulations and couple them with the Hybrid Method of Moments (HMOM). The detailed and reduced model frameworks are validated against experimental measurements of soot volume fraction (ƒ ν ) from a counterflow burner experiment previously reported in the literature. Given the good agreement between modeling results and experimental measurements for the (1) spatial distribution of ƒ ν and (2) the non-linear variation of peak ƒ ν with strain rate, we further investigate the modeled sub-processes (nucleation, condensation, surface growth, and oxidation) using the LLNL model to analyze the assumptions in the reduced model framework. Furthermore, the results indicate a significant contribution from resonant radicals to the surface growth of soot particles, which are not accounted for in the current implementation of HMOM and could help reconcile soot predictions by the reduced model with observations.

Counterflow↗

DOE OSTI2020

Characterizing photovoltaic backsheet adhesion degradation using the wedge and single cantilever beam tests, Part II: Accelerated tests

Photovoltaic (PV) backsheets provide critical moisture, mechanical, and electrical insulation to the backside of PV modules, but their continued functionality depends upon their ability to remain well adhered over years of harsh environmental exposure. A study of adhesive strength was conducted on several PV backsheet types exposed to indoor accelerated weathering. Two adhesion tests – the wedge test and single cantilever beam test – were used to measure adhesion energy in four backsheets: two with fluoropolymer-based outer (airside) layers – polyvinyl fluoride (PVF), polyvinylidene fluoride (PVDF) – and two with non-fluoropolymer-based outer layers–polyamide (PA) and polyethylene terephthalate (PET). The effects of changes in temperature, ultraviolet (UV) irradiance, relative humidity, and a periodic water spray were studied. The PET-, PVF- and PVDF-based backsheets all showed instances of debonding in an adhesive layer, which is commonly reported. Furthermore, for the PA-, PET-, and PVDF-based backsheets, adhesion energy dropped fairly rapidly with exposure, reaching very low levels by 4000 h. The PVF-based backsheet was relatively robust to weathering. Pull-off of an outer chalking layer in the PA- and PET-based backsheets suggested a sensitivity to UV. Adhesion in these two backsheets was also highly sensitive to changes in moisture level. Changes in UV irradiance and temperature did not show a statistically significant effect on adhesion loss for the exposure levels used. The present work is part of a two-part adhesion study on both field-weathered and indoor-exposed backsheets, and forms a basis for understanding adhesion degradation across a variety of backsheet types and degradation factors.

14 SOLAR ENERGY↗

DOE OSTI2024

Material characterization of seven photovoltaic backsheets using seven accelerated test conditions

A variety of polymeric backsheet materials can be found in fielded photovoltaic (PV) modules, mostly based on fluoropolymer and polyethylene terephthalate (PET) materials. Cost reduction and sustainability considerations drive the recent development of alternative backsheet materials and designs [1]. In some fielded PV installations, polymeric materials are susceptible to environmental degradation in the form of backsheet cracking. To prevent backsheet degradation that can result in a module failure, thorough laboratory reliability testing is needed. In this report we studied the durability of seven commercial and experimental PV backsheets through accelerated stress testing using seven photolytic, hygrometric, and custom tests with the goal to understand if novel fluoropolymer-free backsheets are sufficiently environmentally durable to be commercialized. We divided the mechanisms observed during aging into two categories: core degradation and surface degradation. Although core degradation due to hydrolysis was observed in all commercial PET-, and polyamide (PA)-based backsheets aged with 85 degrees C/85% relative humidity, this test is unlikely to be field relevant. Photo-oxidative reactions on the exposed surface during UV weathering affected all seven backsheets regardless of the outer layer polymer material and additives. This degradation was limited to the outermost micrometers of the surface, except for backsheets containing PA-12, which resulted in surface cracking. A custom test combining UV with water spray caused the most severe backsheet degradation, including surface erosion and loss of insulating properties in polyolefin (PO)- and PA-based backsheets. This highlights the importance of combined accelerated stress testing to screen for complex backsheet degradation mechanisms. We also showed that, with material and design optimization, coextruded experimental PO-based backsheets have the potential to be a durable alternative to commercial PET- and fluoropolymer-based PV backsheets.

14 SOLAR ENERGY↗