Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “slots”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Effect of slot width on transition and noise attenuation of a flat sound shield in a Mach 6 wind tunnel

An experimental and theoretical study of a sound shield concept to attenuate the noise radiated into the test section from the turbulent boundary layer on the walls of wind tunnels was conducted. The model investigated was planar with a sharp flat plate leading edge faired into an array of rods aligned nearly parallel to the local flow. For a ratio of gap diameter to rod diameter of 0.16, the flow was laminar over the entire model at a maximum local length Reynolds number of 14 million. A 45% reduction in the tunnel free stream root mean square pressure level was measured within the shielded region for this gap width when the boundary layers on the rods were laminar. Smaller ratios of gap diameter to rod diameter resulted in substantial reductions in the transition Reynolds number, and in a 40% pressure reduction.

Stainback, P. C.↗
NASA NTRS1975

Geometry effects on STOL engine-over-the-wing acoustics with 5.1 slot nozzles

The correspondence of far field acoustic trends with changes in the characteristics of the flow field at the wing trailing edge caused by alterations in the nozzle-wing geometry were determined for several STOL-OTW configurations. Nozzle roof angles of 10 to 40 deg were tested with and without cutback of the nozzle sidewalls. Three wing chord sizes were used: baseline (33 cm with flaps retracted), 2/3-baseline, and 3/2-baseline. Flap deflection angles of 20 and 60 deg were used. The nozzle locations were at 21 and 46-percent of chord. With increasing wing size the jet noise shielding benefits increased. With increasing nozzle roof angle, the jet velocity at the trailing edge was decreased, causing a decrease in trailing-edge and fluctuating lift noise. Cutback of the nozzle sides improved flow attachment and reduced far-field noise. The best flow attachment and least trailing-edge noise generally were obtained with a 40 deg external deflector configuration and a cutback nozzle with a 40 deg roof angle.

Vonglahn, U.↗
NASA NTRS1975

Design and preliminary test results at Mach 5 of an axisymmetric slotted sound shield

The basic theory and sound attenuation mechanisms, the design procedures, and preliminary experimental results are presented for a small axisymmetric sound shield for supersonic wind tunnels. The shield consists of an array of small diameter rods aligned nearly parallel to the entrance flow with small gaps between the rods for boundary layer suction. Results show that at the lowest test Reynolds number (based on rod diameter) of 52,000 the noise shield reduced the test section noise by about 60 percent ( or 8 db attenuation) but no attenuation was measured for the higher range of test reynolds numbers from 73,000 to 190,000. These results are below expectations based on data reported elsewhere on a flat sound shield model. The smaller attenuation from the present tests is attributed to insufficient suction at the gaps to prevent feedback of vacuum manifold noise into the shielded test flow and to insufficient suction to prevent transition of the rod boundary layers to turbulent flow at the higher Reynolds numbers. Schlieren photographs of the flow are shown.

Beckwith, I. E.↗
NASA NTRS1975

Analysis and testing of two-dimensional slot nozzle ejectors with variable area mixing sections

Finite difference computer techniques have been used to calculate the detailed performance of air-to-air two-dimensional ejectors with symmetric variable area mixing sections and coaxial converging primary nozzles. The analysis of the primary nozzle assumed correct expansion of the flow and is suitable for subsonic and slightly supersonic velocity levels. The variation of the mixing section channel walls is assumed to be gradual so that the static pressure can be assumed uniform on planes perpendicular to the axis. A test program was run to provide two-dimensional ejector test data for verification of the computer analysis. A primary converging nozzle with a discharge geometry of 3.18 mm x 203 mm was supplied with 0.340 kg/sec of air at about 2.43 bar and 356 K. This nozzle was combined with two mixing section geometries with throat sizes of 31.8 mm x 203 mm and 47.6 mm x 203 mm and was tested at a total of 11 operating points.

Gilbert, G. B.↗
NASA NTRS1977

Effect of slotted casing treatment with change in Reynolds number index on performance of a jet engine

A tip-treated J85-13 engine was tested at Reynolds number indices (RNI) of 0.3 and 0.7 with a clean inlet for 80- and 100-percent corrected engine speeds. This engine was equipped with a compressor case which allowed changes to the case wall over the rotor tips of six of its eight stages. For all tests, the principal effects were (1) with tip treatment, a stall pressure ratio loss of 6 percent at 100 percent corrected engine speeds for both the 0.3 and 0.7 RNI, and (2) with and without tip treatment, decreasing the RNI from 0.7 to 0.3 decreased the stall pressure ratio 3.8 percent for 100 percent corrected engine speed and 2.8 percent for 80-percent corrected engine speed.

Moss, J. E., Jr.↗
NASA NTRS1982

Performance characteristics of axisymmetric convergent-divergent exhaust nozzles with longitudinal slots in the divergent

An investigation was conducted in the Langley 16 foot Transonic Tunnel and in the static test facility of that tunnel to determine the effects of divergent flap ventilation of an axisymmetric nozzle on nozzle internal (static) and wind on performance. Tests were conducted at 0 deg angle of attack at static conditions and at Mach numbers from 0.6 to 1.2. Ratios of jet total pressure to free stream static pressure were varied from 1.0 (jet off) to approximately 14.0 depending on Mach number. The results of this study indicate that divergent flap ventilation generally provided large performance benefits at overexpanded nozzle conditions and performance reductions at underexpanded nozzle conditions when compared to the baseline (unventilated) nozzles. Ventilation also reduced the peak static and wind on performance levels.

Leavitt, L. D.↗
NASA NTRS1983

Fabricating Slotted-Waveguide Arrays From Sheet Metal

Low-cost lightweight waveguides formed from rolls of aluminum. Array formed from sheared, punched, and bent aluminum sheets. Sheets alined with punched jig holes and joined by laser-beam or resistance spot welding. Process permits use of thin metal to reduce raw material costs and mass. Also holds closer tolerances than usually attained in sheet-metal work.

Brown, W. C.↗
NASA NTRS1981

Low-speed aerodynamic performance of an aspect-ratio-10 supercritical-wing transport model equipped with a full-span slat and part-span and full-span double-slotted flaps

An investigation was conducted in the Langley 4 by 7 Meter Tunnel to determine the static longitudinal and lateral directional aerodynamic characteristics of an advanced aspect ratio 10 supercritical wing transport model equipped with a full span leading edge slat as well as part span and full span trailing edge flaps. This wide body transport model was also equipped with spoiler and aileron roll control surfaces, flow through nacelles, landing gear, and movable horizontal tails. Six basic wing configurations were tested: (1) cruise (slats and flaps nested), (2) climb (slats deflected and flaps nested), (3) part span flap, (4) full span flap, (5) full span flap with low speed ailerons, and (6) full span flap with high speed ailerons. Each of the four flapped wing configurations was tested with leading edge slat and trailing edge flaps deflected to settings representative of both take off and landing conditions. Tests were conducted at free stream conditions corresponding to Reynolds number of 0.97 to 1.63 x 10 to the 6th power and corresponding Mach numbers of 0.12 to 0.20, through an angle of attack range of 4 to 24, and a sideslip angle range of -10 deg to 5 deg. The part and full span wing configurations were also tested in ground proximity.

Morgan, H. L., Jr.↗
NASA NTRS1986

Resonance prediction for slotted wind tunnel by the finite element method

A finite element approach is developed for predicting the so-called 'resonant' frequencies of subsonic wind tunnels with variously shaped cross sections. The resulting computer code has been applied to various wind tunnels. For example, the resonant frequencies for both the NASA Ames Research Center 6 x 6 ft wind tunnel (rectangular cross section) and the NASA Langley Research Center 16 x 16 ft Transonic Dynamics Tunnel (octagonal cross section) have been calculated. The results are believed to be more accurate than theoretical values used in the past for an equivalent rectangular cross section. The effect of a plenum chamber on the resonance is examined in detail. Application of the finite element approach to the plenum chamber, as it interacts with the test section, gives more accurate results than what would be obtained by assuming an open tunnel.

Lee, I.↗
NASA NTRS1989

Experimental transition and boundary-layer stability analysis for a slotted swept laminar flow control airfoil

A swept, supercritical laminar flow control (LFC) airfoil designated NASA SCLFC(1)-0513F was tested at subsonic and transonic speeds in the NASA Langley eight-foot Transonic Pressure Tunnel. This paper examines Tollmien-Schlichting and crossflow disturbance amplification for this airfoil using the linear stability method. The design methodology using linear stability analysis is evaluated and the results of the incompressible and compressible methods are compared. Experimental data on the swept, supercritical LFC airfoil and reference wind tunnel and flight results are used to correlate and evaluate the N-factor method for transition prediction over a speed range M(infinity) from zero to one.

Harvey, William D.↗
NASA NTRS1991

Experimental investigation of the flow field in the head-end star slot section of a solid rocket motor

A test program has been developed to investigate the complex flowfield in the head-end, star grain section of a solid rocket motor. Documentation of the flowfield pattern is to be obtained using both flow visualization techniques and quantitative methods, including static pressure measurements, heat transfer coefficient measurements, and hot-wire anemometry. A cold-flow, one-tenth-scale model based on the geometry of the Space Shuttle SRM head-end section and its single-port igniter, along with two models of a four-port igniter, have been constructed. The scale factor is derived from a scaling analysis which matches Reynolds number between the model and the full-scale flowfield in the star grain section. The NASA Marshall Space Flight Center 14 x 14 inch trisonic wind tunnel will be utilized for the cold flow tests. Since the work is still in progress, no results are included.

Ciucci, A.↗