Results for “shielding effectiveness” — Page 35

NASA NTRS2018

In-situ Diagnostic for Assessing Hall Thruster Wear

The design of a new diagnostic to measure the net erosion of Hall thruster surfaces is presented. This diagnostic consists of a pair of optical noncontact profilometer pens mounted to a set of motion stages, which can interrogate the surface features of multiple components of interest including the hollow cathode assembly, magnet front pole covers, and discharge channel. By comparing scans of these surfaces to reference features, estimates of the component erosion rates can be acquired throughout long-duration lifetime tests without venting and removing the thruster from the vacuum facility for external profilometry. This work presents a detailed overview of the diagnostic design including the precision positioning system. In addition, preliminary data are shown which verify diagnostic operation and establish a baseline that will be used to track the erosion of the Hall Effect Rocket with Magnetic Shielding (HERMeS) Technology Demonstration Unit 3 (TDU-3) during an ongoing long-duration wear test.

Ahern, Drew M.↗

NASA NTRS2018

Long Duration Wear Test of the NASA HERMeS Hall Thruster

The NASA Hall Effect Rocket with Magnetic Shielding (HERMeS) 12.5-kW Hall thruster is the subject of extensive technology maturation by NASA GRC and JPL in preparation for development into a flight propulsion system. As part of this on-going effort, a series of three wear tests have been conducted to identify erosion phenomena and the accompanying failure modes as well as to validate service-life models for magnetically-shielded thrusters. This paper presents an overview and summary of the results obtained over the first 1715 hours of the third wear test, which has the overall goal of serving as a pathfinder to identify and correct design or facility issues prior to the flight qualification campaign. Overall, negligible changes in performance and stability are observed as a function of operating time as well as relative to previous wear tests. Erosion of the inner and outer front pole covers is shown to vary by 76-300 percent as a function of discharge voltage and by up to 40 percent as a function of magnetic field strength. Shifting the cathode position upstream relative to the pole covers is shown to reduce keeper erosion rates by 84 percent, which supports this approach for mitigating the elevated keeper wear observed during previous wear tests.

Frieman, Jason D.↗

NASA NTRS2018

In-Situ Diagnostic for Assessing Hall Thruster Wear

The design of a new diagnostic to measure the net erosion of Hall thruster surfaces is presented. This diagnostic consists of a pair of optical non-contact profilometer pens mounted to a set of motion stages, which can interrogate the surface features of multiple components of interest including the hollow cathode assembly, magnet front pole covers, and discharge channel. By comparing scans of these surfaces to reference features, estimates of the component erosion rates can be acquired throughout long-duration lifetime tests without venting and removing the thruster from the vacuum facility for external profilometry. This work presents a detailed overview of the diagnostic design including the precision positioning system. In addition, preliminary data are shown which verify diagnostic operation and establish a baseline that will be used to track the erosion of the Hall Effect Rocket with Magnetic Shielding (HERMeS) Technology Demonstration Unit 3 (TDU-3) during an ongoing long-duration wear test.

Ahern, Drew M.↗

NASA NTRS2019

Wear Trends of the HERMeS Thruster as a Function of Throttle Point

A series of short-duration (200 h) wear tests were conducted with two Hall Effect Rocket with Magnetic Shielding (HERMeS) technology demonstration units. Front pole covers, cathode keeper, and discharge channel wear were characterized as a function of discharge voltage, magnetic field strength, and chamber pressure. No discharge channel erosion was observed. Inner pole cover erosion was shown to be a weak function of discharge voltage with most erosion occurring at the lowest value, 300 V. The Technology Demonstration Unit (TDU) 3 keeper electrode eroded with each operating condition, with high magnetic field yielding the greatest erosion rate. The TDU-1 keeper electrode exhibited net deposition suggesting its configuration is more consistent with meeting overall HERMeS service life requirements. Ratios of molybdenum to graphite erosion rates suggests, with high uncertainty, that the sputtering ions are originating downstream of the thruster exit plane, striking the surface with small angles of incidence.

Williams, George J., Jr.↗

NASA NTRS2016

Transient Thermal Analysis of the 12.5 KW HERMeS Hall Thruster

NASA’s Dawn spacecraft entered orbit around the dwarf planet Ceres on March 6, 2015 thereby becoming the first mission to orbit two celestial bodies outside of the Earth-moon system. This feat was made possible due to the use of electric propulsion (EP) to provide the 11 km/s of delta-V that was necessary. This type of propulsion is also enabling for many of NASA’s future missions, such as the proposed Asteroid Redirect Robotic Mission (ARRM). Specifically, the Hall Effect Rocket with Magnetic Shielding (HERMeS) is the propulsive design baseline due to its long operational lifetime and high specific impulse. Extensive modeling is required to verify the thruster's predicted thermal performance and survival during the bounding mission phases. Since the thruster would constrain plasma on the order of tens of thousands of hours, components in the thruster must be able to accommodate much higher sustained temperatures than typical spacecraft hardware. Furthermore, the high temperatures necessitate care in analyzing thermal gradients within the thruster. In this paper, we describe a thermal model of the HERMeS thruster and focus upon the thruster's transient performance under different initial firing conditions. The thruster's transient thermal response is critical to verify margin in the thermal stresses inherent in the thruster and to determine safe start-up procedures to protect the thruster's critical components. This model is used to perform transient thermal analysis of the thruster during startup and shutdown, provide temperature maps for structural analysis, and plan for thermal cycle testing conducted at JPL. The thermal cycle testing includes thruster starts at the cold temperature limits and operation at maximum expected external heat flux. This work will support laboratory environmental testing of the HERMeS thruster, which is being conducted at JPL in 2016.

Reilly, Sean↗

NASA NTRS2019

Uncertainty in Electric Propulsion Erosion Measurements

Uncertainty in erosion rates as measured by different methods is discussed and quantified. The work focuses on case studies from components on the Hall Effect Rocket with Magnetic Shielding (HERMeS) Hall thruster, but the methods can be extended for many electric propulsion applications. The primary method used for evaluating erosion is non-contact profilometry of masked and exposed components. Accurate quantification of the erosion rates of components is critical to determining lifetime and is therefore critical to mission planning purposes.

Mackey, J.↗

NASA NTRS2004

Meteoroid Engineering Model – Final Report

We developed a parametric model of the spatial distribution of sporadic meteoroids by taking their primary source to be short-period comets with aphelia less than 7 AU which showed to be the major source of dust released through the sublimation of cometary ices. We constrained the model to fit the observed distribution of particles deduced from the zodiacal light measurements of Helios I and II as well as Earth-based radio-meteor observations. We also considered the contribution to the sporadic meteor complex from long-period comets. An origin for the North and South Toroidal source of sporadic meteors is proposed and the results of calculations for the likely characteristics of asteroidal meteors are also presented. Predicted fluxes and radiant distributions of sporadic meteors in the region between Mercury and Mars are shown as well. We have also included the effects of the gravitational shielding and focusing of the planets and shown that flux enhancements of up to 70% are possible at some locations.

Jones, J.↗

NASA NTRS2019

Completion of the Long Duration Wear Test of the NASA HERMeS Hall Thruster

The NASA Hall Effect Rocket with Magnetic Shielding (HERMeS) 12.5-kW Hall thruster has been the subject of extensive technology maturation by NASA GRC and JPL in preparation for development into a flight propulsion system. As part of this effort, a series of wear tests have been conducted to identify erosion phenomena and the accompanying failure modes as well as to validate service-life models for magnetically-shielded thrusters. This work presents a summary of the results obtained during the Long Duration Wear Test (LDWT), which was the third in this wear test series. The LDWT accumulated approximately 3,570 hours of operation and had the overall goal to identify and correct design or facility issues prior to the flight qualification campaign. Thruster performance, stability, and plume properties were invariant throughout the duration of the LDWT and consistent with measurements acquired during previous HERMeS performance and wear characterizations. Average erosion rates of a carbon-carbon composite pole cover were found to match those measured with graphite to within the empirical uncertainty while the previously observed time-dependence of pole cover erosion rates was linked to changes in pole cover roughness. Azimuthal variations in keeper wear rate were observed including deposition on one of the azimuthal-facing sides of the keeper mask. This strongly suggests the presence of an azimuthal component in the process driving keeper erosion.

Frieman, Jason D.↗

NASA NTRS2019

Uncertainty in Electric Propulsion Erosion Measurements

Uncertainty in erosion rates as measured by different methods is discussed and quantified. The work focuses on case studies from components on the Hall Effect Rocket with Magnetic Shielding (HERMeS) Hall thruster, but the methods can be extended for many electric propulsion applications. The primary method used for evaluating erosion is non-contact profilometry of masked and exposed components. Accurate quantification of the erosion rates of components is critical to determining lifetime and is therefore critical to mission planning purposes.

Mackey, Jonathan A.↗

NASA NTRS2019

Completion of the Long Duration Wear Test of the NASA HERMeS Hall Thruster

The NASA Hall Effect Rocket with Magnetic Shielding (HERMeS) 12.5-kW Hall thruster has been the subject of extensive technology maturation by NASA GRC and JPL in preparation for development into a flight propulsion system. As part of this effort, a series of wear tests have been conducted to identify erosion phenomena and the accompanying failure modes as well as to validate service-life models for magnetically-shielded thrusters. This work presents a summary of the results obtained during the Long Duration Wear Test (LDWT), which was the third in this wear test series. The LDWT accumulated approximately 3,570 hours of operation and had the overall goal to identify and correct design or facility issues prior to the flight qualification campaign. Thruster performance, stability, and plume properties were invariant throughout the duration of the LDWT and consistent with measurements acquired during previous HERMeS performance and wear characterizations. Average erosion rates of a carbon-carbon composite pole cover were found to match those measured with graphite to within the empirical uncertainty while the previously observed time-dependence of pole cover erosion rates was linked to changes in pole cover roughness. Azimuthal variations in keeper wear rate were observed including deposition on one of the azimuthal-facing sides of the keeper mask. This strongly suggests the presence of an azimuthal component in the process driving keeper erosion.

Frieman, Jason D.↗

NASA NTRS2019

Non-Intrusive Characterization of the Wear of the HERMeS Thruster Using Optical Emission Spectroscopy

The Hall Effect Rocket with Magnetic Shielding (HERMeS) is a 12.5 kW Hall thruster electric propulsion string that has been in development by NASA Glenn Research Center(GRC) and NASA JPL since 2012. Due to the magnetically shielded design, service life-limiting erosion of the boron nitride discharge has been virtually eliminated. The inner front pole cover (IFPC) has now been identified as the component defining erosion-based service life. Optical emission spectroscopy (OES) is used as an in-situ diagnostic to measure relative erosion trends during operation of the HERMeS thruster during a series of short duration wear tests. Erosion trends obtained from the OES data will be compared to traditional erosion data measured with a non-contact profilometer.

Gray, Timothy G.↗

NASA NTRS2019

Non-Intrusive Characterization of the Wear of the HERMeS Thruster Using Optical Emission Spectroscopy

The Hall Effect Rocket with Magnetic Shielding (HERMeS) is a 12.5 kW Hall thrusterelectric propulsion string that has been in development by NASA Glenn Research Center(GRC) and NASA JPL since 2012. Due to the magnetically shielded design, service life-limiting erosion of the boron nitride discharge has been virtually eliminated. The innerfront pole cover (IFPC) has now been identied as the component dening erosion-basedservice life. Optical emission spectroscopy (OES) is used as an in-situ diagnostic to measurerelative erosion trends during operation of the HERMeS thruster during a series of shortduration wear tests. Erosion trends obtained from the OES data will be compared totraditional erosion data measured with a non-contact prolometer.

hall thruster↗

NASA NTRS2019

Impact of Facility Pressure on the Wear of the NASA HERMeS Hall Thruster

This work presents an overview and summary of the results acquired during the final segment of the TDU-3 Long Duration Wear Test, which was completed in October 2018. The overall goal of this segment was to quantify the impact of facility pressure on the wear of the Hall Effect Rocket with Magnetic Shielding Technology Demonstration Unit Three (TDU-3) Hall thruster. This was accomplished by operating TDU-3 for approximately 270 hours at the nominal 600 V/12.5 kW operating condition while a bleed or auxiliary flow of xenon propellant was injected into the vacuum facility in order to raise the operating pressure to match that of another test facility in which previous wear segments had been performed. The performance, plume, stability, and wear results acquired at this elevated pressure (11.7 µTorr) are compared with the equivalent data previously taken at the nominal operating pressure (4.2 µTorr).

Frieman, Jason D.↗

NASA NTRS2019

Impact of Facility Pressure on the Wear of the NASA HERMeS Hall Thruster

This work presents an overview and summary of the results acquired during the final segment of the TDU-3 Long Duration Wear Test, which was completed in October 2018. The overall goal of this segment was to quantify the impact of facility pressure on the wear of the Hall Effect Rocket with Magnetic Shielding Technology Demonstration Unit Three (TDU-3) Hall thruster. This was accomplished by operating TDU-3 for approximately 270 hours at the nominal 600 V/12.5 kW operating condition while a bleed or auxiliary flow of xenon propellant was injected into the vacuum facility in order to raise the operating pressure to match that of another test facility in which previous wear segments had been performed. The performance, plume, stability, and wear results acquired at this elevated pressure (11.7 ÂµTorr) are compared with equivalent data taken at the nominal operating pressure (4.2 ÂµTorr) in the same facility as well at the elevated operating pressure in the other facility. Implications of these results for acquiring facility-independent service life estimates are discussed.

Frieman, Jason D.↗

NASA NTRS2019

Completion of the Long Duration Wear Test of the NASA HERMeS Hall Thruster

The NASA Hall Effect Rocket with Magnetic Shielding (HERMeS) 12.5-kW Hall thruster has been the subject of extensive technology maturation by NASA GRC and JPL in preparation for development into a flight propulsion system. As part of this effort, a series of wear tests have been conducted to identify erosion phenomena and the accompanying failure modes as well as to validate service-life models for magnetically-shielded thrusters. This work presents a summary of the results obtained during the Long Duration Wear Test (LDWT), which was the third in this wear test series. The LDWT accumulated approximately 3,570 hours of operation and had the overall goal to identify and correct design or facility issues prior to the flight qualification campaign. Thruster performance, stability, and plume properties were invariant throughout the duration of the LDWT and consistent with measurements acquired during previous HERMeS performance and wear characterizations. Average erosion rates of a carbon-carbon composite pole cover were found to match those measured with graphite to within the empirical uncertainty while the previously observed time-dependence of pole cover erosion rates was linked to changes in pole cover roughness. Azimuthal variations in keeper wear rate were observed including deposition on one of the azimuthal-facing sides of the keeper mask. This strongly suggests the presence of an azimuthal component in the process driving keeper erosion.

Jason David Frieman↗

NASA NTRS2020

Uncertainty in Electric Propulsion Erosion Measurements

Uncertainty in erosion rates as measured by different methods is discussed and quantified. The work focuses on case studies from components on the Hall Effect Rocket with Magnetic Shielding (HERMeS) Hall thruster, but the methods can be extended for many electric propulsion applications. The primary method used for evaluating erosion is non-contact profilometry of masked and exposed components. Accurate quantification of the erosion rates of components is critical to determining lifetime and is therefore critical to mission planning purposes.

Jonathan A Mackey↗

NASA NTRSDate not supplied

Characterization Test of the 12.5-kW Advanced Electric Propulsion System Engineering Test Unit Hall Thruster

This work presents a summary of the detailed characterization testof the 12.5 kW Advanced Electric Propulsion System Engineering Test Unit 2 (AEPS ETU-2) thruster produced by Aerojet Rocketdyne. This test campaign had two major goals: to assessthe risk of design compliance with thruster requirements and providea comparison to the previously-tested NASA Hall Effect Rocket with Magnet Shielding Technology Demonstration Units (HERMeS TDUs) from which the AEPS ETU design was derived.

AEPS↗

NASA NTRS2018

Investigations of Pole Erosion Mechanisms in the 12.5 kW HERMeS Hall Thruster Using Numerical Simulations and Ion Velocity Measurements

When the Hall Effect Rocket with Magnetic Shielding (HERMeS) was tested at the NASA GRC’s VF-5 the erosion rate on the pole covers was found to be at least a factor of two higher at 300 V and 20.8 A than at other operating conditions in the 400 V to 600 V range. Simulations using our hydrodynamics code Hall2De do not predict increased erosion rates at 300 V but accurately compute erosion rates similar to the measurements at the other operating conditions. We investigate the source of the discrepancy between measurements and simulations at 300 V using a combination of numerical simulations and experimental measurements of the ion velocity fields in the acceleration region of the thruster. By examining previous simulations that predicted the measured erosion rates for other thrusters and operating conditions, we determine that sputtering of the pole surfaces by high energy ions is the most likely mechanism behind the erosion rates at 300 V. High energy ions sputter the pole surfaces when the acceleration region of the thruster is downstream of the pole surface plane. When the latter occurs, the curvature of the plasma potential contours at the edges of the channel accelerates a small fraction of the high energy ions radially. We find that neither our Hall2De simulations nor the experimental measurements produce ions of sufficiently high energy and flux to the inner pole cover to explain the measured erosion there. Only at the outer edge of the cover is where we find the ions needed to yield simulation results that are comparable to the erosion measurements. We argue that one possible mechanism for the higher erosion is high energy ions that graze the channel corner of the pole and become trapped in a sheath that develops downstream. Within the sheath, we find that the electric field is large enough to turn the ions towards the surface of the pole. A simplified calculation shows that the erosion rates produced by sputtering of trapped ions are similar to the measurements. We also propose that the presence of local oscillations and high-energy cathode ions may be sources of the enhanced erosion We conclude this article by proposing a combination of analysis, simulation, and experimental measurements that can be used to address the validity of these hypotheses.

Mikellides, Ioannis G.↗