Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polymer additive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Synthesis and Properties of Poly(vinyl chloride)- b -polyethylene Multiblock Copolymers through the Hydrodechlorination of PVC with Silylium Ions

Polymer compatibilizers stabilize the interface between two immiscible polymers to allow for a material that improves properties for additional use. Chlorinated polyethylene (CPE) is a common compatibilizer, yet there does not exist a synthetic pathway either from monomers or via the functionalization of polyethylene (PE) to yield a polymer that has a controlled chlorine amount and primary structure along the polymer chain. Herein, we report a series of novel block copolymers of poly(vinyl chloride) (PVC) and PE, synthesized through selective hydrodechlorination of PVC. Contrary to CPE, the full range of chlorination can be obtained and the block number can be altered. Interfacial adhesion studies reveal samples with competitive compatibilization of PVC/polyolefin elastomer blends (POE). In conclusion, this method shows that post-polymerization modification can be a strategic top-down synthesis to achieve high performance polymers.

Wood, Zachary A. [Univ. of Southern California, Lo↗
DOE OSTI2023

Effect of Molecular Weight on the Morphology of a Polymer Semiconductor–Thermoplastic Elastomer Blend

Abstract Polymer semiconductors (PSCs) are essential active materials in mechanically stretchable electronic devices. However, many exhibit low fracture strain due to their rigid chain conformation and the presence of large crystalline domains. Here, a PSC/elastomer blend, poly[((2,6‐bis(thiophen‐2‐yl)‐3,7‐bis(9‐octylnonadecyl)thieno[3,2‐b]thieno[2′,3′:4,5]thieno[2,3‐d]thiophene)‐5,5′‐diyl)(2,5‐bis(8‐octyloctadecyl)‐3,6‐di(thiophen‐2‐yl)pyrrolo[3,4‐c]pyrrole‐1,4‐dione)‐5,5′‐diyl]] (P2TDPP2TFT4) and polystyrene‐ block ‐poly(ethylene‐ran‐butylene)‐ block ‐polystyrene (SEBS) are systematically investigated. Specifically, the effects of molecular weight of both SEBS and P2TDPP2TFT4 on the resulting blend morphology, mechanical, and electrical properties are explored. In addition to commonly used techniques, atomic force microscopy‐based nanomechanical images are used to provide additional insights into the blend film morphology. Opposing trends in SEBS‐induced aggregation are observed for the different P2TDPP2TFT4 molecular weights upon increasing the SEBS molecular weight from 87 to 276 kDa. Furthermore, these trends are seen in device performance trends for both molecular weights of P2TDPP2TFT4. SEBS molecular weight also has a substantial influence on the mesoscale phase separation. Strain at fracture increases dramatically upon blending, reaching a maximum value of 640% ± 20% in the blended films measured with film‐on‐water method. These results highlight the importance of molecular weight for electronic devices. In addition, this study provides valuable insights into appropriate polymer selections for stretchable semiconducting thin films that simultaneously possess excellent mechanical and electrical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2026

HYBRID COMPOSITES VIA CO-EXTRUSION ADDITIVE MANUFACTURING-COMPRESSION MOLDING FOR PERFORMANCE OPTIMIZATION

The growing demand for hybrid polymer composites with multifunctional properties has led to the development of various hybridization techniques, such as multi-material compounding and controlled laminate stacking sequence. In this study, a novel hybrid manufacturing approach was used by integrating a multiplexing extrusion system (MExS) based on additive manufacturing with subsequent compression molding process. This technique enabled the co-extrusion of different materials during the additive manufacturing process to fabricate composites with tailored performance. The developed hybrid composite featured a skin layer of glass fiberreinforced polycarbonate (PC/GF) encapsulating a carbon fiber-reinforced acrylonitrile butadiene styrene (CF/ABS) core. The structure was engineered to promote improved thermal and impact resistance at the surface, supported by a stiff core for enhanced overall mechanical integrity. Mechanical, thermal and morphological properties of the hybrid composites were investigated to understand trade-offs in performance compared to a single-material system. The results demonstrate that this approach enables the production of multifunctional composites suitable for applications such as automotive body panels and protective housings, where a balance of weight, mechanical strength, and thermal performance is essential.

Wasti, Sanjita [ORNL]↗
DOE OSTI2021

Investigation of chemical stabilities and contact angle of 3D printed polymers with CO 2 capture solvents to enhance absorber performance

Increasing absorption rate in aqueous amine CCS systems is one avenue to decrease capital cost by reducing the overall size of the absorber column. One potential route is by replacing conventional steel packing with custom designed packing made from 3D printed polymers. 3D printing offers endless flexibility in packing designs to better enhance liquid/gas contact, increase CO 2 mass transfer and create compact absorber columns. Additionally, before exploring novel packing designs, it is necessary to identify polymer materials that can be 3D printed while also showing long-term physical and surface property stability upon exposure to corrosive amine solutions. Four polymers that are commonly used for 3D printing were evaluated using CO 2 -loaded amine solution at temperatures typically observed in the absorber column. Three polymers, high-density polystyrene (HDPS), acrylonitrile butadiene styrene (ABS) and nylon were found to be physically stable after 5000 hr of amine exposure at temperatures up to 60 °C. The contact angle (wetting) of water and CO 2 -loaded aqueous amine solution on the polymer surfaces were also stable after exposure to the CO2-loaded amine solution.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Formation of Stable Interphase of Polymer-in-Salt Electrolyte in All-Solid-State Lithium Batteries

The integration of solid-polymer electrolytes into all-solid-state lithium batteries is highly desirable to overcome the limitations of current battery configurations that have a low energy density and severe safety concerns. Polyacrylonitrile is an appealing matrix for solid-polymer electrolytes; however, the practical utilization of such polymer electrolytes in all-solid-state cells is impeded by inferior ionic conductivity and instability against a lithium-metal anode. In this work, we show that a polymer-in-salt electrolyte based on polyacrylonitrile with a lithium salt as the major component exhibits a wide electrochemically stable window, a high ionic conductivity, and an increased lithium-ion transference number. The growth of dendrites from the lithium-metal anode was suppressed effectively by the polymer-in-salt electrolyte to increase the safety features of the batteries. In addition, we found that a stable interphase was formed between the lithium-metal anode and the polymer-in-salt electrolyte to restrain the uncontrolled parasitic reactions, and we demonstrated an all-solid-state battery configuration with a LiFePO 4 cathode and the polymer-in-salt electrolyte, which exhibited a superior cycling stability and rate capability.

Gao, Hongcai↗
DOE OSTI2025

Microwave Debinding of Ceramics Produced by Additive Manufacturing

Microwave-assisted debinding offers an innovative approach to processing 3D-printed engineering ceramics. Ceramic parts produced with photopolymer-based additive manufacturing techniques require thermal debinding to remove polymers that bind ceramic particles during the printing process. Microwave-assisted debinding significantly reduces processing times and offers energy savings over conventional thermal treatments due to higher heating rates and more uniform heating. Finite-element modeling of the debinding process allows for the optimization and prediction of temperature distribution, stress development, and potential defects, leading to improved process control and material quality.

36 - MATERIALS SCIENCE↗
NASA NTRS1991

New addition curing polyimides

In an attempt to improve the thermal-oxidative stability (TOS) of PMR-type polymers, the use of 1,4-phenylenebis (phenylmaleic anhydride) PPMA, was evaluated. Two series of nadic end-capped addition curing polyimides were prepared by imidizing PPMA with either 4,4'-methylene dianiline or p-phenylenediamine. The first resulted in improved solubility and increased resin flow while the latter yielded a compression molded neat resin sample with a T(sub g) of 408 C, close to 70 C higher than PME-15. The performance of these materials in long term weight loss studies was below that of PMR-15, independent of post-cure conditions. These results can be rationalized in terms of the thermal lability of the pendant phenyl groups and the incomplete imidization of the sterically congested PPMA. The preparation of model compounds as well as future research directions are discussed.

Frimer, Aryeh A.↗
DOE OSTI2023

Size effects in 3D–printed polymer–derived, zirconium diboride–reinforced ceramic composites

Preceramic polymers are of interest for use in many manufacturing techniques such as injection molding, ceramic fiber infiltration, and additive manufacturing. However, off-gassing of low molecular weight oligomers occurs when these polymers cure, potentially leading to porosity in the cured part. Here to study how porosity and strength are affected by the size of the printed part, and the presence of a high surface area nano-scale filler, polycarbosilane (PCS) microrods of varying diameter were fabricated via direct ink writing (DIW), an additive manufacturing technique, with two ink formulations containing either zirconium diboride (ZrB 2 ) alone, or ZrB 2 and fumed alumina (FA). Sets of microrods were printed in a range of sizes by using print nozzles of 450, 634, 979, 1 346, or 1 702 μm in diameter, which were thermally cured, pyrolyzed to form ceramic composite microrods, and tested in 3-pt flexure. Porosity increased with increasing diameter, while failure strength decreased. For a given nozzle size, the microrods containing FA displayed lower porosity and higher strength (up to ~500 MPa) compared to the microrods containing only ZrB 2 . Weibull strength analysis was performed on each group of microrods and shows that the addition of FA increased Weibull modulus from 4.63 ± 1.56 to 9.35 ± 0.601. In conjunction with optical microscopy, this analysis indicates two distinct flaw populations in the printed materials, porosity which arises during the curing step and cracking which arises during pyrolysis of the larger specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Degradable Biocomposite Thermoplastic Polyurethanes

In this project, the team developed tough and degradable biocomposite thermoplastic polyurethanes (TPUs) by incorporating bacterial spores into TPUs as a biofunctional living filler. The team screened various bacteria and selected the Bacillus subtilis ATCC 6633 strain as the final candidate, primarily due to its genomic availability, sporulation ability and TPU assimilation activity. The heat-shock tolerance of ATCC 6633 spores was further improved through evolutionary engineering via Adaptive Laboratory Evolution (ALE), demonstrating a 17.7-fold enhanced germination efficiency post heat-shock treatment compared to the wild-type strain (WT). The team fabricated biocomposite TPUs by incorporating lyophilized powder of heat-shock tolerized (HST) spores during the hot melt extrusion (HME) of TPU at 135 °C. The baseline TPU used in this project is a commercially available soft-grade TPU (BCF45) manufactured by BASF. Colony forming unit (CFU) assays quantified that WT and HST spores in the TPU matrix retained approximately 20% and 100% survivability, respectively, after HME. Tensile testing demonstrated that the spores behaved as a polymer-reinforcing filler, positively affecting the overall tensile properties of the biocomposite TPU. For example, biocomposite TPU with WT and HST spores (BC TPU WT and BC TPU HST , respectively) exhibited up to 25% and 37% improved toughness, respectively, compared to TPU without spores. BC TPU HST showed remarkably improved disintegration in autoclaved compost (92% mass loss in 5 months), which simulated a microbially poor environment for TPU degradation. When compared to TPU without spores (44% mass loss in 5 months) the acceleration of degradation is marked. Respirometry confirmed that 72% of BC TPU HST was biomineralized into CO2 within 6 months, indicating that spores in the biocomposite TPU were germinated by utilizing nutrients in the autoclaved compost, facilitating TPU degradation at the end of the material's life. The team demonstrated the scale-up of biocomposite TPU fabrication using continuous extrusion and injection molding techniques. Processing conditions optimized in a lab-scale microcompounder were successfully transferred to a continuous extruder with a 30-fold increased throughput. Biocomposite TPUs prepared using these industry-relevant processes showed comparable toughness improvements to samples prepared in the lab-scale extruder. Excitingly, following compounding in the pilot-extruder the composite material could be injection molded, while retaining high spore viability and similar toughness improvements. The team also found that spores in biocomposite TPU served as antioxidants, preventing toughness decay during the recycled extrusion of BC TPU HST . Long-term storage tests over one year showed that the addition of spores had no negative effect on the longevity of the TPU. Furthermore, the team demonstrated the fabrication of spore-bearing biocomposite polymers with other polyesters such as PBAT, PLA, and PCL. We obtained promising preliminary data that showed overall toughness improvements for all polymers with spore addition. Finally, life cycle assessment (LCA) and techno-economic analysis (TEA) were carried out, which indicated minimal additional cost of fabrication. Overall, a tough and degradable biocomposite thermoplastic was successfully developed through this project, with all tasks completed successfully, achieving >100% of the objectives.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanical Performance and Mesostructure Analysis of Proton-Irradiated Fused Filament Fabrication Acrylonitrile Butadiene Styrene Material

The use of fused filament fabrication (FFF) acrylonitrile butadiene styrene (ABS) and other thermoplastics in radiation environments is beginning to be studied as possible replacements for traditionally manufactured parts and tools. Interlayer adhesion within the mesostructure has been shown in published literature to be an integral component in the strength of FFF ABS. Research of irradiated 3D printed polymers has primarily focused on the influence of gamma irradiation on the mechanical properties of FFF ABS samples, without evaluating its impact on the mesostructure of the samples. The purpose of this paper is to understand the mechanical damage caused by proton radiation on FFF ABS samples through the evaluation of the mesostructure of the ABS samples. To achieve this objective, proton radiation at 40 MeV was applied to FFF ABS samples at radiation doses up to 1.0 MGy at a dose rate of 1 MGy/hr. Following the irradiation, tensile testing was performed on the samples. Here, the fractured surfaces of the tested samples were subsequently observed using a scanning electron microscope. The mechanical test results show an increase in the ultimate tensile strength (UTS) and a decrease in the ductility of the irradiated samples. Statistical analysis on the results shows that there is a statistically significant difference in the UTS and the ductility of unirradiated and 1.0 MGy irradiated samples and between irradiated samples and 1.0 MGy samples. In addition, the percentage elongation at break has statistically significant differences in the means between irradiated samples and 1.0 MGy samples. The UTS has statistically significant differences in the means between 0.1 MGy and 1.0 MGy. The difference in the means between the unirradiated and the 1.0 MGy samples is the most significant for both the UTS and elongation at break. The scanning electron microscopy (SEM) results indicated that interlayer adhesion improved as a function of radiation dose corresponding to the increase in tensile strength. The SEM results also showed that crazing and plastic deformation were reduced; aligning with the loss in ductility observed in the tensile tests results. The proton radiation is causing these mechanical and physical changes through two mechanisms: (1) dose rate effects on ionizing radiation-induced oxidative degradation; and (2) radiation heating effects of high energy (>1 MeV) charged particles.

electron microscopy↗
DOE OSTI2023

Oxidation performance and limitations of additively manufactured SiC/Si-O-C composites at elevated temperatures

Here, SiC preforms were infiltrated with polycarbosiloxane preceramic polymer to create low-cost SiC—Si x O y C z matrix composites for possible high temperature application. The effect of specimen annealing conditions on the steam and air oxidation resistance was analyzed. Air exposures from 900–1500°C showed stability of the Si x O y C z matrix phase with moderate oxidation resistance. After 900°C exposures, oxidation of the composite is primarily limited to the matrix phase, and only at 1200 and 1500°C was SiC consumption visualized. Steam cycle exposures at 1200°C resulted in rapid linear oxidation of the composites with induced specimen swelling from volume expansion associated with internal oxidation. Specimens annealed in argon were found to be the most oxidation resistant due to increased matrix crystallinity and carbon retention. The results of this work were used to develop clear strategies for improving the high-temperature properties of SiC—Si x O y C z composites.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Self-assembly of wood-based shape memory composites triggered by solar-thermal energy

Transporting and assembling large, complex structures poses significant challenges due to their size, geometry, and cost. Additionally, the installation sites are often inaccessible or hazardous for humans, necessitating self-assembling capabilities in these structures. To mitigate these challenges, we propose using 3D printing materials with shape memory effect (SME) for both transport and construction. This approach involves developing 3D modular components into flat sheets for easier transportation, and then self-assembling into 3D structures on-site using solar energy. To gain a deeper understanding of the factors influencing material memory performance, we have chosen a composite PLA/WF, which is polylactic acid (PLA) with 20 wt% wood flour (WF) for this purpose, leveraging its high tensile modulus at 0.966 GPa, low cost, and sustainability. Printed shapes with this material can maintain a recovery ratio over 90% after 3 cycles. While traditional composites fillers (e.g. glass or carbon fiber) are added to enhance mechanical and thermal properties, the addition of bio-based fillers like WF accomplish similar goals without compromising sustainability. We conducted multiple experiments to demonstrate how environmental conditions (i.e. temperature) maximize the material’s SME. Although still at an early stage, this study provides initial insights into bridging the gap between the small-scale nature of shape memory polymers (SMPs) and their potential for large-scale additive manufacturing, addressing a critical need for efficient and sustainable construction. In the long term, we hope our study contributes to the design vision of utilizing SMPs for transportation, assembly, and deployment of complex structures, providing a new pathway for sustainable construction and transportation of large-scale structures to hard-to-access locations such as disaster-affected areas and remote deserts, etc.

4D printing↗
DOE OSTI2023

Synthesis of hyperbranched polymer films via electrodeposition and oxygen-tolerant surface-initiated photoinduced polymerization

Hypothesis Hyperbranched polymers, not only possess higher functionality, but are also easier to prepare compared to dendrimers and dendric polymers. Combining electrodeposition and surface-initiated photoinduced electron transfer-reversible addition-fragmentation chain transfer (SI-PET-RAFT) polymerization is hypothesized to be a novel strategy for preparing hyperbranched polymer films on conductive surfaces without degassing. Experiments In this study, polymer brush grafted films with four different architectures (i.e. linear, branched, linear- block -branched, and branched- block -linear) were prepared on gold-coated glass substrates using electrodeposition, followed by SI-PET-RAFT polymerization. The resulting film structure and thickness, surface topology, absorption property, and electrochemical behavior were confirmed by spectroscopy, microscopy, microbalance technique, and impedance measurement. Findings These hyperbranched polymer brushes were capable of forming a thicker but more uniformly covered films compared to linear polymer brush films, demonstrating that hyperbranched polymer films can be potentially useful for fabricating protective polymer coatings on various conductive surfaces.

36 MATERIALS SCIENCE↗
NASA NTRS1995

LDEF polymeric materials: A summary of Langley characterization

The NASA Long Duration Exposure Facility (LDEF) enabled the exposure of a wide variety of materials to the low earth orbit (LEO) environment. This paper provides a summary of research conducted at the Langley Research Center into the response of selected LDEF polymers to this environment. Materials examined include graphite fiber reinforced epoxy, polysulfone, and additional polyimide matrix composites, films of FEP Teflon, Kapton, several experimental high performance polyimides, and films of more traditional polymers such as poly(vinyl toluene) and polystyrene. Exposure duration was either 10 months or 5.8 years. Flight and control specimens were characterized by a number of analytical techniques including ultraviolet-visible and infrared spectroscopy, thermal analysis, scanning electron and scanning tunneling microscopy, x-ray photoelectron spectroscopy, and, in some instances, selected solution property measurements. Characterized effects were found to be primarily surface phenomena. These effects included atomic oxygen-induced erosion of unprotected surfaces and ultraviolet-induced discoloration and changes in selected molecular level parameters. No gross changes in molecular structure or glass transition temperature were noted. The intent of this characterization is to increase our fundamental knowledge of space environmental effects as an aid in developing new and improved polymers for space application. A secondary objective is to develop benchmarks to enhance our methodology for the ground-based simulation of environmental effects so that polymer performance in space can be more reliably predicted.

Young, Philip R.↗
DOE OSTI2022

X-ray Computed Tomography as a Metrology Technique for the Analysis of Additively Manufactured Material

X-ray computed tomography (X-ray CT) is an analytical technique used in materials science to non-destructively characterize features in a variety materials like polymer, metals, composites, and explosives. It also has the capability of imaging additively manufacture, machine and assembled parts. The non-destructive imaging allows for the analysis of features (voids and cracks), which give a fundamental understanding of the material characteristics. Additionally, X-ray CT can obtain accurate measurements of dimensional and topographic variations due to different stimuli and assess the accuracy of material production. This study focuses on parts manufactured via metal additive manufacturing (AM). Although AM produces parts faster and easier, the printing process can produce defects (pores and surface roughness) that undermine the part’s mechanical properties and performance. The analysis of 3D printed objects has an asset in that the material has an STL file from which the item was printed, which is not available in many manufactured materials (i.e., foams) due to stochastic structures. For this study, the print accuracy of four additively manufactured cylinders will be assessed via X-ray CTto approximate the surface roughness and visualize any major morphological changes to assess the dimensional accuracy of complex additively manufactured parts. It was concluded that using X-ray CT to measure surface roughness was affective because reasonable surface roughness values were measured. Additionally, itwas determined that small-scale features can be produced via additive manufacturing with strong dimensional accuracy so long as the features are highly complex with sharp grooves.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Enhancing the Solubility of Semiconducting Polymers in Eco-Friendly Solvents with Carbohydrate-Containing Side Chains

Semiconducting polymers are at the forefront of next-generation organic electronics due to their robust mechanical and optoelectronic properties. However, their extended π-conjugation often leads to materials with low solubilities in common organic solvents, thus requiring processing in high-boiling-point and toxic halogenated solvents to generate thin-film devices. To address this environmental concern, a natural product-inspired side-chain engineering approach was used to incorporate galactose-containing moieties into semiconducting polymers toward improved processability in greener solvents. Novel isoindigo-based polymers with different ratios of galactose-containing side chains were synthesized to improve the solubilities of the organic semiconductors in alcohol-based solvents. The addition of carbohydrate-containing side chains to π-conjugated polymers was found to considerably impact the intermolecular aggregation of the materials and their microstructures in the solid state as confirmed by atomic force microscopy and grazing-incidence wide-angle X-ray scattering. The charge transport characteristics of the new semiconductors were evaluated by the fabrication of organic field-effect transistors prepared from both toxic halogenated and greener alcohol-based solvents. Importantly, the incorporation of carbohydrate-containing side chains was shown to have very little detrimental impact on the electronic properties of the polymer when processed from green solvents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

The Effect of TiDG, DCiTG (Lix ® reg;79), and Other Suppressors on the Compatibility of NGS with SWPF Polymers

This document provides a screening calculation of the potential miscibility of specific polymers proposed for use in the SWPF, notably polyether-etherketone (PEEK), ultra-high molecular weight polyethylene (UHMWPE), polyvinylidene fluoride (PVDF), Viton ® B fluoroelastomer, and Tefzel ® ethylenetetrafluoroethylene (ETFE) copolymer in different suppressors including trisisodecyl guanidine (TiDG), dicyclohexane-isotrisdecyl guanidine (DCiTG), and two other dicyclohexane guanidine related suppressors. The evaluation suggests that Tefzel ® ETFE may mildly interact with the Next Generation Solvent (NGS) regardless of the suppressor used. Based on this approach (calculations), the other listed polymers appear compatible with the NGS containing the four different suppressors. There is evidence of chemical affinity between Tefzel ® ETFE, Viton ® B with aliphatic amines (which are degradation by-products from the TiDG). In addition, the calculation suggests that drawing miscibility conclusions from exposing polymers to a single pure component may give misleading or incorrect results due to the potential for synergistic effects or other interactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗