Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polycrystalline material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Stabilizing Ni-rich layered cathode for high-voltage operation through hierarchically heterogeneous doping with concentration gradient

High-nickel LiNi x Mn y Co 1-x-y O 2 (NMC) cathodes have demonstrated superior energy density, yet their stability is compromised under high voltage conditions. To address this, here we propose a strategy of heterogeneous doping with a concentration gradient, specifically through Sr–Zr co-modification. We synthesized Ni-rich NMC particles featuring several micron-sized secondary particles composed of micron-sized primary grains. This design aims to harness the structural robustness of single-crystalline grains and the favorable diffusion kinetics of polycrystalline secondary particles. Systematic characterization using a combination of electrochemical measurements and synchrotron analytics reveals an intriguing pattern of hierarchically heterogeneous Sr–Zr co-doping. It demonstrates a depth-dependent concentration gradient at the secondary particle level and competing dopant segregation over the buried grain boundaries. This unique characteristic creates opportunities for enhancing battery performance, particularly by optimizing precursors and implementing advanced modulation techniques. We also investigate the dissolution and precipitation of the cathode's transition metal cations upon high-voltage cycling. These insights suggest that a tailored compositional variation can be a viable approach to effectively design the next-generation high-Ni NMC cathode materials for high-voltage lithium batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Nanoscale Ferroelectric Control of Novel Electronic States in Layered Two-Dimensional Materials (Final Report)

In this DOE Early Career project “Nanoscale Ferroelectric Control of Novel Electronic States in Layered Two-Dimensional Materials,” the PI’s group has combined ferroelectric field effect with nanoscale domain imaging and writing to design the electronic and optical properties of two-dimensional (2D) van der Waals materials, including graphene and transition metal dichalcogenides MoS2 and ReS2. The van der Waals materials have been prepared into field effect transistor (FET) devices with ferroelectric gates. Through domain patterning in a ferroelectric polymer PVDF-TrEF top-gate via conductive atomic force microscopy, the team has created programmable Schottky junctions in monolayer MoS 2 , where both barrier height and I-V rectifying polarity can be reconfigured. The transport anisotropy of monolayer to few-layer ReS 2 has been mapped out by defining the entire channel into an insulating state and creating nanoscale conducting paths along different directions through domain writing in the ferroelectric top-gate. The result shows that the conductivity along and perpendicular to the Re-chain can differ by >5.5x10 4 . Theoretical modeling points to the band origin of the transport anomaly and reveals the emergence of a flat band in few-layer ReS 2 . The interfacial epitaxial relation between ReS 2 and PVDF-TrFE further promotes the formation of close-packed, highly ordered PVDF-TrFE nanowires with width of 35 nm and 10 nm. Nonvolatile modulation of quantum Hall effect has been achieved in graphene FETs with a ferroelectric oxide Ba 0.4 Sr 0.6 TiO 3 back-gate. Scattering from the remote surface optical phonon in Ba 0.4 Sr 0.6 TiO 3 limits the room temperature mobility of graphene to be about 3x10 4 cm 2 /Vs. Steep-slope switching has been achieved in MoS 2 FETs back-gated by polycrystalline Pb(Zr,Ti)O 3 , which signals a static-state negative capacitance mode without involving an additional dielectric layer. Piezoresponse force microscopy studies show that the sub-threshold swing can be well correlated with the domain wall density in Pb(Zr,Ti)O 3 . The team also observes an unconventional filtering effect of the second harmonic generation response at the MoS 2 /Pb(Zr,Ti)O 3 heterointerface, which can be accounted for by the alignment between one of the polar axes of MoS 2 and the chiral dipole rotation at the surface of domain wall in Pb(Zr,Ti)O 3 . The research supported by this DOE grant has significantly advanced the fundamental understanding and functional design of ferroelectric/2D van der Waals heterostructures for their implementation towards energy applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Universal Machine Learning Model for Elemental Grain Boundary Energies

The grain boundary (GB) energy has a profound influence on the grain growth and properties of polycrystalline metals. Here, we show that the energy of a GB, normalized by the bulk cohesive energy, can be described purely by four geometric features. By machine learning on a large computed database of 361 small Σ (Σ<10) GBs of more than 50 metals, we develop a model that can predict the grain boundary energies to within a mean absolute error of 0.13 J m –2 . More importantly, this universal GB energy model can be extrapolated to the energies of high Σ GBs without loss in accuracy. These results highlight the importance of capturing fundamental scaling physics and domain knowledge in the design of interpretable, extrapolatable machine learning models for materials science.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Disentangling Electronic Transport and Hysteresis at Individual Grain Boundaries in Hybrid Perovskites via Automated Scanning Probe Microscopy

Underlying the rapidly increasing photovoltaic efficiency and stability of metal halide perovskites (MHPs) is the advancement in the understanding of the microstructure of polycrystalline MHP thin film. Over the past decade, intense efforts have been aimed at understanding the effect of microstructures on MHP properties, including chemical heterogeneity, strain disorder, phase impurity, etc. It has been found that grain and grain boundary (GB) are tightly related to lots of microscale and nanoscale behavior in MHP thin films. Atomic force microscopy (AFM) is widely used to observe grain and boundary structures in topography and subsequently to study the correlative surface potential and conductivity of these structures. For now, most AFM measurements have been performed in imaging mode to study the static behavior; in contrast, AFM spectroscopy mode allows us to investigate the dynamic behavior of materials, e.g., conductivity under sweeping voltage. However, a major limitation of AFM spectroscopy measurements is that they require manual operation by human operators, and as such only limited data can be obtained, hindering systematic investigations of these microstructures. Here, we designed a workflow combining the conductive AFM measurement with a machine learning (ML) algorithm to systematically investigate grain boundaries in MHPs. The trained ML model can extract GBs locations from the topography image, and the workflow drives the AFM probe to each GB location to perform a current–voltage (IV) curve automatically. Then, we are able to have IV curves at all GB locations, allowing us to systematically understand the property of GBs. Using this method, we discovered that the GB junction points are less conductive, potentially more photoactive, and can play critical roles in MHP stability, while most previous works only focused on the difference between GB and grains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Ferromagnetism and structural phase transition in rhombohedral PrI r 3

The synthesis, structural, magnetic, thermal, and transport properties are reported for polycrystalline PrI⁢r 3 . At room temperature PrI⁢r 3 displays the rhombohedral space group R–3m and a PuNi 3 -type structure. At around 70 K a phase transition to a monoclinic C⁢2/m structure is observed and continued cooling reveals temperature independent behavior of the unit cell volume. Further, PrI⁢r 3 undergoes a paramagnetic to ferromagnetic transition with T c =7.5K. The temperature dependent magnetic susceptibility follows the Curie-Weiss law with a positive Curie-Weiss temperature, and an effective moment that is close to the theoretical effective moment for a free P⁢r +3 ion. Finally, the structural transition introduces further complexity into the behavior of PuNi 3 -type materials and highlights the importance of temperature-dependent structural studies to complement physical property measurements in intermetallic compounds.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

ZrN Phase Formation, Hardening and Nitrogen Diffusion Kinetics in Plasma Nitrided Zircaloy-4

Plasma nitridation was conducted to modify the surfaces of Zircaloy-4. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Raman analysis were used to characterize microstructures and phases. Surface indentation and cross-sectional indentation were performed to evaluate mechanical property changes. Nitridation forms a thin layer of ZrN phase, followed by a much deeper layer affected by nitrogen diffusion. The ZrN phase is confirmed by both TEM and Raman characterization. The Raman peaks of ZrN phase show a temperature dependence. The intensity increases with increasing nitridation temperatures, reaches a maximum at 700 °C, and then decreases at higher temperatures. The ZrN layer appears as continuous small columnar grains. The surface polycrystalline ZrN phase is harder than the bulk by a factor of ~8, and the nitrogen diffusion layer is harder by a factor of ~2–5. The activation energy of nitrogen diffusion was measured to be 2.88 eV. The thickness of the nitrogen-hardened layer is controllable by changing the nitridation temperature and duration.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Domain wall enabled steep slope switching in MoS2 transistors towards hysteresis-free operation

Abstract The device concept of ferroelectric-based negative capacitance (NC) transistors offers a promising route for achieving energy-efficient logic applications that can outperform the conventional semiconductor technology, while viable operation mechanisms remain a central topic of debate. In this work, we report steep slope switching in MoS 2 transistors back-gated by single-layer polycrystalline PbZr 0.35 Ti 0.65 O 3 . The devices exhibit current switching ratios up to 8 × 10 6 within an ultra-low gate voltage window of $$V_{{{\mathrm{g}}}} = \pm \! 0.5$$ V g = ± 0.5 V and subthreshold swing (SS) as low as 9.7 mV decade −1 at room temperature, transcending the 60 mV decade −1 Boltzmann limit without involving additional dielectric layers. Theoretical modeling reveals the dominant role of the metastable polar states within domain walls in enabling the NC mode, which is corroborated by the relation between SS and domain wall density. Our findings shed light on a hysteresis-free mechanism for NC operation, providing a simple yet effective material strategy for developing low-power 2D nanoelectronics.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Study of Se and Cl segregation in poly-crystalline CdSeTe

CdTe based thin film solar cells have shown to be competitive in terms of efficiency and low cost, but the polycrystalline structure and low minority carrier lifetime constrain CdTe based devices from reaching the theoretical efficiency limit. In this work, the effect of Se and Cl segregation in polycrystalline CdSeTe photovoltaic devices was studied. We demonstrated using two-photon time-resolved photoluminescence (TRPL) that the Se alloyed CdSeTe absorber layer shows high minority carrier lifetime, and used density functional theory (DFT) calculations to explain the origin of such high lifetime.

cadmium compounds↗
DOE OSTI2021

Evolution of texture and internal stresses within polycrystalline rock salt using in situ 3D synchrotron computed tomography and 3D X-ray diffraction

Over time rock salt caverns have been extensively used as reliable repositories for hazardous waste such as nuclear waste, oil or compressed gases. Undisturbed rock salt deposits in nature are usually impermeable and have very low porosity. However, rock salt formations under excavation stresses can develop crack networks, which increase their porosities; and in the case of a connected crack network within the media, rock salt may become permeable. Although the relationship between the permeability of rock salt and the applied stresses has been reported in the literature, a microscopic study that investigates the properties influencing this relationship, such as the evolution of texture and internal stresses, has yet to be conducted. This study employs in situ 3D synchrotron micro-computed tomography and 3D X-ray diffraction (3DXRD) on two small-scale polycrystalline rock salt specimens to investigate the evolution of the texture and internal stresses within the specimens. The 3DXRD technique measures the 3D crystal structure and lattice strains within rock salt grains. The specimens were prepared under 1D compression conditions and have shown an initial {111} preferred texture, a dominant {110}$\langle1\bar{1}0\rangle$ slip system and no fully connected crack network. The {111} preferred texture under the unconfined compression experiment became stronger, while the {111}$\langle1\bar{1}0\rangle$ slip system became more prominent. The specimens did not have a fully connected crack network until applied axial stresses reached about 30 MPa, at a point where the impermeability of the material becomes compromised due to the development of multiple major cracks.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Phase patterning of metallic glasses through superfast quenching of ion irradiation-induced thermal spikes

Amorphous metallic glasses (MGs) convert to crystalline solids upon annealing at a high temperature. Such a phase change, however, does not occur with the local melting caused by damage cascades introduced by ion irradiation, although the resulting thermal spikes can reach temperatures > 1000 K. This is because the quenching rate of the local melting zone is several orders of magnitude higher than the critical cooling rate for MG formation. Thus the amorphous structure is sustained. This mechanism increases the highest temperature at which irradiated MG sustains amorphous phase. More interestingly, if an irradiated MG is pre-annealed to form a polycrystalline structure, ion irradiation can locally convert this crystalline phase to an amorphous phase if the grains are nanometers in size and comparable to the damage cascade volume size. Combining pre-annealing and site selective ion irradiation, patterned crystalline-amorphous heterogeneous structures have been fabricated. This finding opens new doors for various applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Programmable Catalyst Structures via Adsorbate-Induced Adatom Assembly

The electronic structure and geometric configuration of oxide-supported metal ions are important coordination properties that can be related to catalytic activity and stability. Herein, we interrogate the coordination environment of mononuclear Pd ions supported on ceria using CO adsorption, infrared vibrational spectroscopy, and DFT modeling. We observed the 15 h continuous co-evolution of a palladium- (2167 cm -1 ) and cerium-carbonyl (2177 cm -1 ) complex by monitoring the $\nu$(CO) infrared region. The slow CO adsorption kinetics were caused by the reactive ligand exchange between an oxygen atom of the support and the CO adsorbate to yield an oxygen vacancy and adsorbed CO 2 . We hypothesize that the co-evolved cerium-carbonyl complex was formed upon CO adsorption at or adjacent to this oxygen vacancy. Our hypothesis was experimentally supported by a dramatic attenuation of the cerium carbonyl signal upon pre-adsorption of water through an apparent competitive adsorption mechanism. The attenuation was also accompanied by a 6 cm -1 redshift of the palladium carbonyl band (2161 cm -1 ) attributed to hydrogen bonding between the carbonyl and a nearby hydroxyl. Characteristic n(CO) stretch frequencies catalogued through CO adsorption onto single crystal ceria by Wöll et al.1 led us to index the cerium carbonyl to the {100} nanofacet of the polycrystalline ceria support. It follows from the observed co-evolution of the two carbonyl complexes that Pd was also adsorbed at the {100} nanofacet. Redeployment of a previously developed DFT model by Ivanova-Shor et al.2 featuring square-planar coordination of Pd2+ at the {100} nanofacet (O 4 Pd) of a Ce 21 O 42 nanoparticle model qualitatively reproduced several experimental observations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Finite Difference Analysis of the Effect of Graphene Additions on the Electrical Conductivity of Polycrystalline Copper

A finite-difference method was used to explore the effect of graphene on the bulk electrical conductivity of copper-graphene composites. In this capacity, grain orientation information from pure copper and copper-graphene composites were used to generate synthetic 3D microstructures. The electrical conductivity of these microstructures were calculated using the finite difference method assuming different average grain sizes. From these calculations, we demonstrate that when high-conductivity grain boundaries are present within the microstructure arising from the presence of graphene, an increase in the bulk electrical conductivity is observed. On the other hand, the difference in textures between copper and copper-graphene composites may not account for a significant difference in bulk electrical conductivity. In comparison, the copper grain size has a considerably larger effect on electrical conductivity as previously anticipated. This is one of the first demonstrations of a physical basis for enhanced conductivity composites and presents pathways for further investigations on the effects of composite microstructural features, material interfaces and graphene content on electrical performance.

Frazier, William E.↗
DOE OSTI2021

Proton irradiation-induced blistering in UO2

Abstract Proton (H + ) irradiation effects in polycrystalline UO 2 have been studied. The irradiation was carried out using three ion energies and two different ion fluxes at 600 °C. Scanning electron microscopy (SEM) investigations showed that significant surface flaking took place. Focused ion beam (FIB) milling in SEM was successfully applied for extracting lamellas from uneven blistered surfaces for transmission electron microscopy (TEM) investigations allowing detailed investigations for the degradation mechanisms. High-resolution TEM for the flaked UO 2 surfaces revealed that the implanted H + formed sharp two-dimensional cavities at the peak ion-stopping region instead of diffusing to the matrix. The resulting lateral stress likely caused UO 2 surface deterioration in good agreement with previous blistering and flaking studies on crystalline materials. Graphical abstract

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Pinhole electrical conductivity in polycrystalline Si on locally etched SiN$_y$/SiO$_x$ passivating contacts for Si solar cells

State-of-the-art monocrystalline Si (c-Si) solar cells require passivating contacts to achieve a high degree of charge-carrier separation and collection. In this work, we focus on boron-doped polycrystalline Si on locally etched silicon nitride/silicon oxide (PLENO) passivating contacts. In PLENO contacts, excellent surface passivation is provided by the ~10 nm dielectric bilayer, while pinholes in the dielectric bilayer, that are filled with doped polycrystalline Si, provide charge-carrier selectivity and transport. During PLENO fabrication, etch undercut in the dielectric bilayer occurs. Here, using electrical characterization and microscopies, we show that undercut causes pinholes to be electrically resistive in PLENO. A processing sequence that eliminates the undercut in the final PLENO structure results in electrically conductive pinholes with low contact resistivity.

14 SOLAR ENERGY↗
DOE OSTI2020

Effect of pH on the Activity of Ice-Binding Protein from Marinomonas primoryensis

The ability of an ice-binding protein (IBP) from Marinomonas primoryensis (MpIBP) to influence ice crystal growth and structure in nonphysiological pH environments was investigated in this work. The ability for MpIBP to retain ice interactivity under stressed environmental conditions was determined via (1) a modified splat assay to determine ice recrystallization inhibition (IRI) of polycrystalline ice and (2) nanoliter osmometry to evaluate the ability of MpIBP to dynamically shape the morphology of a single ice crystal. Circular dichroism (CD) was used to relate the IRI and DIS activity of MpIBP to secondary structure. The results illustrate that MpIBP secondary structure was stable between pH 6 and pH 10. It was found that MpIBP did not interact with ice at pH=4 or pH=13. At 6=pH=12 MpIBP exhibited a reduction in grain size of ice crystals as compared to control solutions and demonstrated dynamic ice shaping at 6=pH=10. The results substantiate that MpIBP retains some secondary structure and function in non-neutral pH environments; thereby, enabling its potential utility in nonphysiological materials science and engineering applications.

antifreeze proteins↗
DOE OSTI2020

Comparison of Hafnium Dioxide and Zirconium Dioxide Grown by Plasma-Enhanced Atomic Layer Deposition for the Application of Electronic Materials

We report the growth of nanoscale hafnium dioxide (HfO 2 ) and zirconium dioxide (ZrO 2 ) thin films using remote plasma-enhanced atomic layer deposition (PE-ALD), and the fabrication of complementary metal-oxide semiconductor (CMOS) integrated circuits using the HfO 2 and ZrO 2 thin films as the gate oxide. Tetrakis (dimethylamino) hafnium (Hf[N(CH 3 ) 2 ] 4 ) and tetrakis (dimethylamino) zirconium (IV) (Zr[N(CH 3 ) 2 ] 4 ) were used as the precursors, while O 2 gas was used as the reactive gas. The PE-ALD-grown HfO 2 and ZrO 2 thin films were analyzed using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and high-resolution transmission electron microscopy (HRTEM). The XPS measurements show that the ZrO 2 film has the atomic concentrations of 34% Zr, 2% C, and 64% O while the HfO 2 film has the atomic concentrations of 29% Hf, 11% C, and 60% O. The HRTEM and XRD measurements show both HfO 2 and ZrO 2 films have polycrystalline structures. n-channel and p-channel metal-oxide semiconductor field-effect transistors (nFETs and pFETs), CMOS inverters, and CMOS ring oscillators were fabricated to test the quality of the HfO 2 and ZrO 2 thin films as the gate oxide. Current-voltage (IV) curves, transfer characteristics, and oscillation waveforms were measured from the fabricated transistors, inverters, and oscillators, respectively. The experimental results measured from the HfO 2 and ZrO 2 thin films were compared.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Additively-manufactured monocrystalline YBCO superconductor

Abstract Single-crystal microstructures enable high-performance YBa 2 Cu 3 O 7-x superconductors which are however limited to simple shapes due to their brittleness. Additive manufacturing can fabricate YBa 2 Cu 3 O 7-x superconductor with complex shapes, albeit with a polycrystalline microstructure. Here, we demonstrate a route to grow single-crystals from 3D-ink-printed, polycrystalline, sintered superconducting YBa 2 Cu 3 O 7-x (YBCO or Y123) + Y 2 BaCuO 5 (Y211), manufacturing objects with complex architectures displaying both high critical current density (J c =2.1 × 10 4 A . cm –2 , 77 K) and high critical temperature (T c = 88-89.5 K). An ink containing precursor powders (Y 2 O 3 , BaCO 3 , and CuO) is 3D-extruded into complex geometries and then reaction-sintered to obtain polycrystalline Y123 + Y211. A seed is then utilized to transform these 3D-printed parts from polycrystal to monocrystal via the melt growth method. The geometric details of 3D-printed parts survive the process without slumping, sagging or collapse, despite the long-term presence of liquid above the peritectic temperature. Origami structures can be created by sheet folding after 3D-printing. This additive approach enables the facile fabrication of superconducting devices with complex shapes and architectures, such as advanced undulator magnets to generate synchrotron radiation and microwave cavities for dark-matter axion search. This work highlights the potential of additive manufacturing for producing monocrystalline cuprate superconductors and opens the door to additive manufacturing of other monocrystalline functional ceramic or semiconductor materials.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Combinatorial sputter deposition of ultrathick Au-Bi alloy films

We report gold-bismuth alloys are of interest as catalysts and catalytic sensing systems, electrochemical sensors, superconductors, and hohlraums for magnetically assisted inertial confinement fusion implosions. Radiation-hydrodynamics simulations with the Lasnex code of laser-driven hohlraums predict higher x-ray drive from Au-Bi alloys compared with cases of Au-Ta or pure Au and Bi hohlraums. Here, we use direct current magnetron sputtering in Ar gas, with co-sputtering from two elemental targets, to deposit Au-Bi alloys with Bi content of 9–77 at.% and thicknesses up to ~20 µm. Films are characterized by a combination of x-ray diffraction, Rutherford backscattering, scanning electron microscopy, substrate-curvature-based residual stress, and electronic transport measurements. Experiments are complemented by Monte Carlo simulations of ballistic sputtering and gas phase transport of depositing species and Ar gas atoms. Results show that all films are polycrystalline, with three distinct compositional regimes dominated by Au, Au 2 Bi, and Bi crystallographic phases. A metallic behavior of the temperature dependence of electrical resistivity is observed for all the films. Films with Bi content above ~30 at.% exhibit porosity, which is tolerable to hohlraum x-ray drive based on Lasnex simulations.

36 MATERIALS SCIENCE↗