Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phase identification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Investigation into the propagation of Omega very low frequency signals and techniques for improvement of navigation accuracy including differential and composite omega

An analysis of Very Low Frequency propagation in the atmosphere in the 10-14 kHz range leads to a discussion of some of the more significant causes of phase perturbation. The method of generating sky-wave corrections to predict the Omega phase is discussed. Composite Omega is considered as a means of lane identification and of reducing Omega navigation error. A simple technique for generating trapezoidal model (T-model) phase prediction is presented and compared with the Navy predictions and actual phase measurements. The T-model prediction analysis illustrates the ability to account for the major phase shift created by the diurnal effects on the lower ionosphere. An analysis of the Navy sky-wave correction table is used to provide information about spatial and temporal correlation of phase correction relative to the differential mode of operation.

Source record↗

High-Pressure Apparatus for Monitoring Solid–Liquid Phase Transitions

This work presents a new technique for observing the solid–liquid phase transformations in complex diesel fuel blends and diesel surrogates under high-pressure conditions intended to simulate those occurring in vehicle fuel injectors. A high-pressure apparatus based on a visual identification of freezing and thawing has been designed and built to monitor phase behavior and determine the crystallization temperature of complex fuels to predict wax precipitation. The proposed methodology was validated using pure substances—n-hexadecane (C16H34), cyclohexane (C6H12), and a binary cyclohexane/n-hexadecane mixture—all of which have been well-characterized previously. The crystallization temperatures of these compounds were measured from atmospheric pressure to 400 MPa for temperatures varying from 290 to 363 K and compared to those reported in the literature. The standard error of the estimated temperatures, based on a given pressure, between the experimental data obtained in this work was compared to data in the literature from Domanska et al. This methodology is being extended to investigate the properties of more complex fuel mixtures.

High-Pressure, phase change, diesel, solidificatio↗

Acute phase response, inflammation and metabolic syndrome biomarkers of Libby asbestos exposure

Identification of biomarkers assists in the diagnosis of disease and the assessment of health risks from environmental exposures. We hypothesized that rats exposed to Libby amphibole (LA) would present with a unique serum proteomic profile which could help elucidate epidemiologically-relevant biomarkers. In four experiments spanning varied protocols and temporality, healthy (Wistar Kyoto, WKY; and F344) and cardiovascular compromised (CVD) rat models (spontaneously hypertensive, SH; and SH heart failure, SHHF) were intratracheally instilled with saline (control) or LA. Serum biomarkers of cancer, inflammation, metabolic syndrome (MetS), and the acute phase response (APR) were analyzed. All rat strains exhibited acute increases in α-2-macroglobulin, and α1-acid glycoprotein. Among markers of inflammation, lipocalin-2 was induced in WKY, SH and SHHF and osteopontin only in WKY after LA exposure. While rat strain- and age-related changes were apparent in MetS biomarkers, no LA effects were evident. The cancer marker mesothelin was increased only slightly at 1 month in WKY in one of the studies. Quantitative Intact Proteomic profiling of WKY serum at 1 day or 4 weeks after 4 weekly LA instillations indicated no oxidative protein modifications, however APR proteins were significantly increased. Those included serine protease inhibitor, apolipoprotein E, α-2-HS-glycoprotein, t-kininogen 1 and 2, ceruloplasmin, vitamin D binding protein, serum amyloid P, and more 1 day after last LA exposure. All changes were reversible after a short recovery regardless of the acute or long-term exposures. Thus, LA exposure induces an APR and systemic inflammatory biomarkers that could have implications in systemic and pulmonary disease in individuals exposed to LA. -- Highlights: ► Biomarkers of asbestos exposure are required for disease diagnosis. ► Libby amphibole exposure is associated with increased human mortality. ► Libby amphibole increases circulating proteins involved in acute phase response. ► Libby amphibole exposure increases circulating osteopontin and lipocalin-2. ► Rats with heart failure have compromised ability to mount acute phase response.

60 APPLIED LIFE SCIENCES↗

Phase Segmentation in Atom-Probe Tomography Using Deep Learning-Based Edge Detection

Abstract Atom-probe tomography (APT) facilitates nano- and atomic-scale characterization and analysis of microstructural features. Specifically, APT is well suited to study the interfacial properties of granular or heterophase systems. Traditionally, the identification of the interface between, for precipitate and matrix phases, in APT data has been obtained either by extracting iso-concentration surfaces based on a user-supplied concentration value or by manually perturbing the concentration value until the iso-concentration surface qualitatively matches the interface. These approaches are subjective, not scalable, and may lead to inconsistencies due to local composition inhomogeneities. We introduce a digital image segmentation approach based on deep neural networks that transfer learned knowledge from natural images to automatically segment the data obtained from APT into different phases. This approach not only provides an efficient way to segment the data and extract interfacial properties but does so without the need for expensive interface labeling for training the segmentation model. We consider here a system with a precipitate phase in a matrix and with three different interface modalities—layered, isolated, and interconnected—that are obtained for different relative geometries of the precipitate phase. We demonstrate the accuracy of our segmentation approach through qualitative visualization of the interfaces, as well as through quantitative comparisons with proximity histograms obtained by using more traditional approaches.

47 OTHER INSTRUMENTATION↗

The electric field dependence of single electron emission in the PIXeY two-phase xenon detector

Dual phase xenon detectors are widely used in experimental searches for galactic dark matter particles. The origin of single electron backgrounds following prompt scintillation and proportional scintillation signals in these detectors is not fully understood, although there has been progress in recent years. Here, in this paper, we describe single electron backgrounds in 83m Kr calibration events and their correlation with drift and extraction fields, using the Particle Identification in Xenon at Yale (PIXeY) dual-phase xenon time projection chamber. The single electron background induced by the Fowler-Nordheim (FN) effect is measured, and its electric field dependence is quantified. The photoionization of grids and impurities by prompt scintillation and proportional scintillation also contributes to the single electron background.

47 OTHER INSTRUMENTATION↗

The Role of Convection and Growth Competition in Phase Selection in Microgravity: Controlled Convection in the Containerless Processing of Steel Alloys

Containerless processing using electromagnetic levitation (EML) is a powerful technique in the investigation of reactive molten metal systems. On ground, the power required to overcome the weight of the sample is sufficient to cause significant heating and induce substantial melt convection. In microgravity, the heating and positioning fields may be decoupled and the field strength may be varied to achieve the desired level of convection within the limits set by the geometry of the levitation coil and the sample size. From high-speed digital images of the double recalescence behavior of Fe-Cr-Ni alloys in ground-based testing and in reduced-gravity aboard the NASA KC-135 parabolic aircraft, we have shown that phase selection can be predicted based on a growth competition model. An important parameter in this model is the delay time between primary nucleation and subsequent nucleation of the stable solid within the liquid/metastable solid array. This delay time is a strong function of composition and a weak function of the undercooling of the melt below the metastable liquidus. From the results obtained during the first Microgravity Sciences Laboratory (MSL-1) mission, we also know that convection may significantly influence the delay time, especially at low undercoolings. Currently, it is unclear what mechanism controls the formation of a heterogeneous site that allows nucleation of the austenitic phase on the pre-existing ferrite skeleton. By examining the behavior of the delay time under different convective conditions, we hypothesize that we can differentiate between several of these mechanisms to gain an understanding of how to control microstructural. evolution. We will anchor these predictions by examining samples quenched at different times following primary recalescence in microgravity. A second important parameter in the growth competition model is the identification of the growth rate of the stable phase into the semi-solid array that formed during primary recalescence. Current dendritic growth theory is inadequate in predicting solidification behavior under these conditions as metallographic analyses show that stable phase growth proceeds along the interface between the metastable solid and residual liquid. Since growth velocity is independent of the initial undercooling relative to the metastable liquidus, we hypothesize that purely thermal effects can be separated from other important growth model parameters by careful selection of the liquid composition in a ternary system.

Matson, D. M.↗

Mineralogy at Gusev Crater and Meridiani Planum from the Moessbauer Spectrometers on the Mars Exploration Rovers

The Moessbauer spectrometers on the twin MER rovers Spirit and Opportunity have provided significant new information on the distribution of iron among its oxidation states, the identification of the mineralogical composition of iron-bearing phases, and the distribution of iron among those phases for rock and soil at Gusev Crater and Meridiani Planum. The plains of Gusev Crater are dominated by olivine-bearing basalt (approximately Fo(60)) and Fe(3+)/Fe(total)=0.1 - 0.5. The oxide mineral generally present is magnetite. In contrast, initial results for the Columbia Hills are consistent with the presence of hematite and a ferrous iron phase, possibly pyroxene. Gusev spectra also have a ferric doublet (not jarosite) that is tentatively associated with nano-phase ferric oxide. A wider diversity of material is present at Meridiani Planum. Significantly, jarosite-bearing outcrop is present throughout the region, with good exposures in impact craters such as Eagle and Endurance (Fe(3+)/Fe (total) approx. 0.9). The Moessbauer identification of jarosite (a hydroxyl-bearing sulfate mineral) is evidence for aqueous, acid-sulfate processes on Mars. Hematite is observed within the outcrop matrix and in the spheroidal particles (Blueberries) found within the outcrop and as a surface lag. An isolated rock (Bounce Rock) was the only sample at either landing site whose iron-bearing phase was dominated by pyroxene. The basaltic sand in the central portion of Eagle crater, in the intercrater plains, and between slabs of outcrop at both Eagle and Endurance craters is olivine-bearing basalt. The widespread occurrence of olivine-bearing basalt at both MER landing sites implies that physical, rather than chemical, weathering processes dominate at the surface of contemporary Mars.

Morris, Richard V.↗

Single-shot in-line x-ray phase-contrast imaging of void-shockwave interactions in fusion energy materials

Recent breakthroughs in nuclear fusion, specifically the report of reactions exceeding scientific breakeven at the National Ignition Facility (NIF), highlight the potential of inertial fusion energy (IFE) as a sustainable and virtually limitless energy source. However, further progress in IFE requires characterization of defects in ablator materials and how they affect fuel capsule compression. Voids within the ablator can degrade energy yield, but their impact on the density distribution has primarily been studied through simulations, with limited high-resolution experimental validation. To address this, we used the x-ray free-electron laser (XFEL) at the matter in extreme conditions (MECs) instrument at the Linac coherent light source (LCLS) to capture 2D x-ray phase-contrast (XPC) images of a void-bearing sample with a composition similar to inertial confinement fusion (ICF) ablators. By driving a compressive shockwave through the sample using MEC's long-pulse laser system, we analyzed how voids influence shockwave propagation and density distribution during compression. To quantify this impact, we extracted phase information using two phase retrieval algorithms. First, we applied the contrast transfer function (CTF) method, paired with Tikhonov regularization and a fast optimization approach to generate an initial phase estimate. We then refined the result using a projected gradient descent (PGD) method that works directly with the sample's refractive index. Comparing these results with radiation adaptive grid Eulerian (xRAGE) radiation hydrodynamic simulations enables identification of model validation needs or improvements. By calculating phase maps in situ, it becomes possible to reconstruct areal density maps, improving understanding of laser-capsule interactions and advancing IFE research.

Hodge, D. S. [Colorado State Univ., Fort Collins, ↗

Abiotic and Biotic Damage of Microalgae Generate Different Volatile Organic Compounds (VOCs) for Early Diagnosis of Algal Cultures for Biofuel Production

Open microalgal ponds used in industrial biomass production are susceptible to a number of biotic and abiotic environmental stressors (e.g., grazers, pathogens, pH, temperature, etc.) resulting in pond crashes with high economic costs. Identification of signature chemicals to aid in rapid, non-invasive, and accurate identification of the stressors would facilitate targeted and effective treatment to save the algal crop from a catastrophic crash. Specifically, we were interested in identifying volatile organic compounds (VOCs) that can be used to as an early diagnostic for algal crop damage. Cultures of Microchloropsis gaditana were subjected to two forms of algal crop damage: (1) active grazing by the marine rotifer, Brachionus plicatilis, or (2) repeated freeze–thaw cycles. VOCs emitted above the headspace of these algal cultures were collected using fieldable solid phase microextraction (SPME) fibers. An untargeted analysis and identification of VOCs was conducted using gas chromatography-mass spectrometry (GC-MS). Diagnostic VOCs unique to each algal crop damage mechanism were identified. Active rotifer grazing of M. gaditana was characterized by the appearance of carotenoid degradation products, including β-cyclocitral and various alkenes. Freeze–thaw algae produced a different set of VOCs, including palmitoleic acid. Both rotifer grazing and freeze–thawed algae produced β-ionone as a VOC, possibly suggesting a common stress-induced cellular mechanism. Importantly, these identified VOCs were all absent from healthy algal cultures of M. gaditana. Early detection of biotic or abiotic environmental stressors will facilitate early diagnosis and application of targeted treatments to prevent algal pond crashes. Thus, our work further supports the use of VOCs for monitoring the health of algal ponds to ultimately enhance algal crop yields for production of biofuel.

09 BIOMASS FUELS↗

FCC feasibility studies: Impact of tracker- and calorimeter-detector performance on jet flavor identification and Higgs physics analyses

The ambitious physics program planned for the Future Circular Collider electron-positron phase imposes stringent constraints on detector performance. This study systematically investigates how different detector configurations impact jet flavor identification and their effects on high-profile physics analyses. Using Higgs boson coupling measurements and searches for invisible Higgs decays as benchmarks, we evaluate the sensitivity of these analyses to variations in tracker and calorimeter detector properties. We examine modifications to single-point resolution, material budget, silicon layer placement, and particle identification capabilities, quantifying their effects on flavor-tagging performance. Additionally, we present the first comprehensive study of Higgs-to-invisible decay detection using full detector simulation, providing insights for optimizing detector designs at lepton colliders.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

AN ATLAS OF FAR-ULTRAVIOLET SPECTRA OF THE ZETA AURIGAE BINARY 31 CYGNI WITH LINE IDENTIFICATIONS

The ζ Aurigae system 31 Cygni (K4 Ib + B4 V) was observed by the FUSE satellite during total eclipse and at three phases during chromospheric eclipse. We present the coadded, calibrated spectra and atlases with line identifications. During total eclipse, emission from high ionization states (e.g., Fe III and Cr III) shows asymmetric profiles redshifted from the systemic velocity, while emission from lower ionization states (e.g., Fe II and O I) appears more symmetric and is centered closer to the systemic velocity. Absorption from neutral and singly ionized elements is detected during chromospheric eclipse. Late in chromospheric eclipse, absorption from the K star wind is detected at a terminal velocity of ∼80 km s{sup –1}. These atlases will be useful for interpreting the far-UV spectra of other ζ Aur systems, as the observed FUSE spectra of 32 Cyg, KQ Pup, and VV Cep during chromospheric eclipse resemble that of 31 Cyg.

79 ASTRONOMY AND ASTROPHYSICS↗

Direct synthesis of thermochromic VO{sub 2} through hydrothermal reaction

Thermochromic VO{sub 2} was directly synthesized using hydrothermal techniques. The effects of formation conditions on the structure and morphology of the final product were studied through X-ray diffraction (XRD), and scanning electron microscopy (SEM). Unique hollow sphere morphology was observed for the synthesized VO{sub 2} powders. Ex-situ XRD studies after heat treatment confirmed the thermal stability of the VO{sub 2} structure. Thermochromic properties, as a consequence of the reversible structural transformation between monoclinic VO{sub 2} and tetragonal phases, were observed by Fourier transform infrared spectroscopy (FTIR). - Graphical abstract: Thermochromic VO{sub 2} crystals with hollow spherical and asterisk shape were directly synthesized using hydrothermal techniques. X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) studies confirmed the thermal stability and the reversible thermochromic properties of the VO{sub 2} structure. - Highlights: • One-step synthesis of thermochromic VO{sub 2} monoclinic phase, and VO{sub 2} (A and B phases) using hydrothermal technique. VO{sub 2} (A), VO{sub 2} (B). • Identification of the relationship between synthesis conditions and the morphology/structure of the final products. • Formation of VO{sub 2} monoclinic phase with an interesting hollow sphere shape. • Demonstration of superior thermal stability of the VO{sub 2} monoclinic phase. • Characterizing the thermochromic properties of VO{sub 2} monoclinic phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Derivation of the midinfrared (5.0-25.0 micron) optical constants of hydrous carbonate and sulfate

There is ample theoretical and observational evidence suggesting liquid water was once stable at the surface of Mars. Because water is essential to the evolution of life, it is important to understand the types of environments in which the liquid water was present. For example, if water were present early in Mars' history, then this raises the possibility that biological activity may have evolved only to eventually become extinct as liquid water became scarce. Alternatively, if liquid water were stable only later in Mars' history, then it becomes problematic to envision mechanisms by which biological activity evolved and remained viable without water until more favorable conditions existed. Even without biological activity, atmospheric carbon dioxide dissolved in water can assist the chemical weathering of primary igneous minerals producing common secondary phases such as hydartes, carbonates, and sulfates. While the identification of hydrates, carbonates, and sulfates on Mars cannot provide direct evidence of biological activity, it can provide significant information regarding the presence and duration of an environment that would support the presence of liquid water at the surface. The specific mineralogy of these secondary phases can provide insight into the environments of their formation. For example, the slow precipitation that occurs in large standing bodies of water, e.g. oceans or lakes, commonly results in the formation of calcite, magnesite, dolomite, siderite, and rhodochrosite. Rapid precipitation that occurs in ephemeral bodies of water, e.g. hypersaline lakes or playas, can result in the formation of all of the above phases as well as aragonite, vaterite, hydrated carbonates, alkali carbonates, bicarbonates, and other poorly ordered phases. Absorption features identified in recent near-infrared spectra of Mars have been interpreted as being due to bicarbonate and bisulfate located in the mineral scaplite. Spectral data returned by the Mariner 6 and 7 spacecraft have been inerpreted as remaining consistent with the presence of hydrated carbonates. Additional, airborne thermal infrared spectra of Mars have been interpreted as implying the presence of carbonates, sulfates, and hydrates. Modeling of the thermal infrared data relied upon the optical constants of calcite anhydrite and a mixture of water in basalt because of their availability. The derived abundances of carbonate and sulfate were 1-3 percent and 10-15 percent by volume. However, the observed complexity and positions of the bands suggested other carbonate-, and sulfate-bearing species. We have already derived optical constants for hydrous and anhydrous silicates, and we are now applying these techniques to the derivation of the optical constants of hydrous carbonate and sulfate.

Roush, Ted L.↗

Theoretical Studies of Polar Systems near Ferroelectrics Quantum Critical Points (Final Report)

The PI has studied emergent quantum phases near polar quantum critical points. A first challenge was to develop a theoretical description of the observation that many polar materials undergo classical first-order transitions while displaying quantum criticality. The possibility of novel metallic states near polar quantum critical points was then studied; identification and characterization of a non-Fermi liquid phase was made in a multiband system. In dilute quantum critical polar metals, electronic coupling to polar energy fluctuations was shown to result in attractive electron-electron interactions and to superconductivity. A spin-phonon resonance measurement in applied magnetic field was proposed to determine the magnitude of spin-orbit mediated electron-phonon coupling; furthermore in the polar phase new field-induced phonon collective modes were identified with specific signatures for experiment. In order to keep current, the PI has also worked on other types of strongly correlated problems. With experimental groups, she has developed phenomenologies to identify and explain observed dynamical critical behaviors. The PI has studied the interplay of topology, fractionalization and deconfinement in a minimalist spin model. An emergent phase transition in a 1 + 1 frustrated spin nanotube has also been identified and characterized. The PI has also begun exploring criticality out of equilibrium, characterizing rich dynamical phases associated with photoinduced polar transitions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Phase shift errors in the theory and practice of surface intensity measurements

The surface acoustical intensity method (sometimes known as the microphone-accelerometer cross-spectral method) is a relatively new noise source/path identification tool. Several researchers have had difficulties implementing this method because of instrumentation phase mis-match. A simple technique for measuring and correcting instrumentation phase mis-match has been developed. This new technique has been tested recently on a noise source identification problem of practical interest. The results of the experiments indicate that the surface acoustic intensity method produces reliable data and can be applied to a variety of noise source/path problems.

Mcgary, M. C.↗

Designing Remote Monitoring for Smart Manufacturing Facilities: Hazard Identification and Classification

This study investigates the process of hazard identification in complex manufacturing environments during the design phase, emphasizing the significance of the design process in developing designs that effectively mitigate hazards in contexts with numerous variables, such as a variety of machines, sensors, actuators, and agents. Through a mixed-methods approach, the objective of this work is to understand how the evolution of design outcomes across various stages might influence a designer’s ability to recognize both standard and novel hazards. To achieve this understanding, an experimental design task was conducted with six designers from a national lab specializing in manufacturing technologies. This approach combined qualitative and quantitative data analysis from a one-hour virtual session with participants. Findings suggest that the complexity of identifying hazards in a high-dimensional design space is challenging within a limited time frame and that the identification of hazards is significantly influenced by the stage of the design task and the initial design decisions, indicating the need for extended time and strategic initial planning in the design process to enhance hazard identification.

Ballestas, Caseysimone↗

Thermodynamic Activity Measurements with Knudsen Cell Mass Spectrometry

Coupling the Knudsen effusion method with mass spectrometry has proven to be one of the most useful experimental techniques for studying the equilibrium between condensed phases and complex vapors. The Knudsen effusion method involves placing a condensed sample in a Knudsen cell, a small "enclosure", that is uniformly heated and held until equilibrium is attained between the condensed and vapor phases. The vapor is continuously sampled by effusion through a small orifice in the cell. A molecular beam is formed from the effusing vapor and directed into a mass spectrometer for identification and pressure measurement of the species in the vapor phase. Knudsen cell mass spectrometry (KCMS) has been used for nearly fifty years now and continues to be a leading technique for obtaining thermodynamic data. Indeed, much of the well-established vapor specie data in the JANAF tables has been obtained from this technique. This is due to the extreme versatility of the technique. All classes of materials can be studied and all constituents of the vapor phase can be measured over a wide range of pressures (approximately 10(exp -4) to 10(exp -11) bar) and temperatures (500-2800 K). The ability to selectively measure different vapor species makes KCMS a very powerful tool for the measurement of component activities in metallic and ceramic solutions. Today several groups are applying KCMS to measure thermodynamic functions in multicomponent metallic and ceramic systems. Thermodynamic functions, especially component activities, are extremely important in the development of CALPHAD (Calculation of Phase Diagrams) type thermodynamic descriptions. These descriptions, in turn, are useful for modeling materials processing and predicting reactions such as oxide formation and fiber/matrix interactions. The leading experimental methods for measuring activities are the Galvanic cell or electro-motive force (EMF) technique and the KCMS technique. Each has specific advantages, depending on material and conditions. The EMF technique is suitable for lower temperature measurements, provided a suitable cell can be constructed. KCMS is useful for higher temperature measurements in a system with volatile components. In this paper, we briefly review the KCMS technique and identify the major experimental issues that must be addressed for precise measurements. These issues include temperature measurements, cell material and cell design and absolute pressure calibration. The resolution of these issues are discussed together with some recent examples of measured thermodynamic data.

Copland, Evan H.↗