Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “operations flight operations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

TO252: Parabolic Flight Demonstration of Fluid Dispensing Tube Performance Limits for Drop Delivery

Ring Shear Drop (RSD) ISS flight hardware failed to pin sample fluid drops between two rings, likely due to dynamic instability inherent to the dispensing tube (D-Tube) design. The first parabolic flight tested 5 D-tube tip designs with two bounding surface tension fluids, enabling an engineering design decision. D-tube Tip Cage Design was selected based on the November 2020 parabolic flight test data. Flight Operations Program (FOP) approved a reflight proposal to include 2 parabolic flight days during the April/May 2021 campaign with following objectives: • Validate ISS hardware flight design with actual flight fluids (test as you fly), demonstrating the ability to deliver 1” fluid drops in near-microgravity conditions. • Demonstrate pinning of 1” flight fluid drops: a secondary pinning ring is planned to be installed in the parabolic flight hardware to meet this objective. Fluid flow rates will also be varied as needed and as possible. • Provide data to validate computational models used to guide ISS operational deployment decisions and demonstrate the viability of the redesigned hardware to accommodate a range of future flight investigations. This presentation introduces highlights and lessons learned during this recent flight campaign for discussion in the Flight Opportunities Program Panel, “Leveraging Suborbital Flight Tests to Advance Science and Technology."

Sridhar Gorti↗
NASA NTRS1996

Enhancing the Flight Safety Culture Through Training

In the 1970's, flight safety professionals became profoundly concerned about the prevalence of crew-caused accidents and incidents, and the role of human error in flight operations. As result, they initiated a change in the flight safety culture which has grown to significant proportions today. At the heart of the evolution were crew concepts such as flightdeck management, crew coordination, and cockpit resource management, concepts which seemed to target critical deficiencies. In themselves, the concepts were not new but their incorporation into training as a direct means of changing the flight safety culture was an untried, almost 'grassroots' approach. The targeted crew concepts and skills were not an integral part of the typical training program; the methods, curriculum, media, and even course content itself, would have to be developed and implemented from the bottom up. A familiar truism in the pilot culture is that you should 'Train the way you fly; Fly the way you train'. In short, training was expected to provide the pilot with practical operational skills that were consistent with the performance standards they were required to maintain and the operational demands they met on a daily basis. In short, one could not simply command crews to use good CRM; one would have to research and define these skills operationally as well as develop and implement a consistent and effective training program. Furthermore, one would need active support and collaboration among the research, industry and government communities in order to ensure acceptance and continued commitment. Additional information is contained in the original extended abstract.

Kanki, Barbara G.↗
NASA NTRSDate not supplied

NASA’s Secured Airspace for Urban Air Mobility (UAM)

The Urban Air Mobility (UAM) architecture is leveraged from the Unmanned Traffic Management (UTM) concept of operations. Within the UAM environment, UAM operators work collaboratively to manage aerial vehicles in the urban environment. Providers of Services for UAM (PSU), UAM operators, and Supplemental Data Service Providers (SDSP) provide services to support flight operations within that environment. As a recognized need, various views of UAM flight information are provided to the public and public safety entities. To accomplish this, among other goals, the Federal Aviation Administration (FAA) can coordinate flight information between the FAA controlled National Airspace System (NAS) and the UAM environments through the FAA-Industry Data Exchange Protocol (FIDXP). This concept of UAM proposes to develop short-range, point-to-point transportation systems in metropolitan areas using vertical take-off and landing (VTOL) or short take-off and landing (STOL) aircraft to overcome increasing surface congestion. To garner the support of UAM and to realize its potential, an assurance of cybersecurity is critical for public acceptance. Understanding the various components communicating with one-another cybersecurity, like in other industries, has come to the forefront highlighting the need to protect these networks and systems from cyberattacks. With the planned growth and reach of UAM systems, it’s clear that the associated data exchange and service interactions will be at risk due to numerous types of cybersecurity attacks. Consequently, as these threats evolve, the UAM cybersecurity capabilities must adapt to these changes as well. While learning is always the goal, the overall intent of this workshop is to make recommendations on the following: (1) how future UAM environments can be protected against cyber-attacks, and (2) what mechanisms should be put in place to detect attacks against UAM environments.

UAM↗
NASA NTRS1993

PILOT: An intelligent distributed operations support system

The Real-Time Data System (RTDS) project is exploring the application of advanced technologies to the real-time flight operations environment of the Mission Control Centers at NASA's Johnson Space Center. The system, based on a network of engineering workstations, provides services such as delivery of real time telemetry data to flight control applications. To automate the operation of this complex distributed environment, a facility called PILOT (Process Integrity Level and Operation Tracker) is being developed. PILOT comprises a set of distributed agents cooperating with a rule-based expert system; together they monitor process operation and data flows throughout the RTDS network. The goal of PILOT is to provide unattended management and automated operation under user control.

Rasmussen, Arthur N.↗
NASA NTRS1965

SPODP - Single Precision Orbit Determination Program

This Technical Memorandum describes the Single Precision Orbit Determination Program which was developed for operation under the data processing system of the Space Flight Operations Facility. Included are sections containing flow diagrams, load maps, the common storage map, input and output descriptions, subroutine writeups, operating instructions, and check cases. The computational methods employed by the program are described in the subroutine documentation.

COMPUTER PROGRAM↗
NASA NTRS1982

Shuttle automatic landing system

The Shuttle automatic landing system design requirements are discussed, the approach and landing flight phase is described, and the hardware and software subsystems are functionally described. Emphasis is placed on the complexity, flexibility, and criticality of the software function. The software structure, critical computational problems, and verification process as a subsystem are discussed. Finally, the hardware/software verification activities required before flight test of the autoland system are described, along with the results from two flight tests and the planned system certification to the operational flight boundaries.

Tsikalas, G.↗
NASA NTRS1995

Alternate charging profiles for the onboard nickel cadmium batteries of the Explorer Platform/Extreme Ultraviolet Explorer

The Explorer Platform/Extreme Ultraviolet Explorer (EP/EUVE) spacecraft power is provided by the Modular Power Subsystems (MPS) which contains three 50 ampere-hour Nickel Cadmium (NiCd) batteries. The batteries were fabricated by McDonnell Douglas Electronics Systems Company, with the cells fabricated by Gates Aerospace Batteries (GAB), Gainesville, Florida. Shortly following launch, the battery performance characteristics showed similar signatures as the anomalous performance observed on both the Upper Atmosphere Research Satellite (UARS) and the Compton Gamma Ray Observatory (CGRO). This prompted the development and implementation of alternate charging profiles to optimize the spacecraft battery performance. The Flight Operations Team (FOT), under the direction of Goddard Space Flight Center's (GSFC) EP/EUVE Project and Space Power Applications Branch have monitored and managed battery performance through control of the battery Charge to Discharge (C/D) ratio and implementation of a Solar Array (SA) offset. This paper provides a brief overview of the EP/EUVE mission, the MPS, the FOT's battery management for achieving the alternate charging profile, and the observed spacecraft battery performance.

Rao, Gopalakrishna M.↗
NASA NTRS2006

Another Approach to Enhance Airline Safety: Using Management Safety Tools

The ultimate goal of conducting an accident investigation is to prevent similar accidents from happening again and to make operations safer system-wide. Based on the findings extracted from the investigation, the "lesson learned" becomes a genuine part of the safety database making risk management available to safety analysts. The airline industry is no exception. In the US, the FAA has advocated the usage of the System Safety concept in enhancing safety since 2000. Yet, in today s usage of System Safety, the airline industry mainly focuses on risk management, which is a reactive process of the System Safety discipline. In order to extend the merit of System Safety and to prevent accidents beforehand, a specific System Safety tool needs to be applied; so a model of hazard prediction can be formed. To do so, the authors initiated this study by reviewing 189 final accident reports from the National Transportation Safety Board (NTSB) covering FAR Part 121 scheduled operations. The discovered accident causes (direct hazards) were categorized into 10 groups Flight Operations, Ground Crew, Turbulence, Maintenance, Foreign Object Damage (FOD), Flight Attendant, Air Traffic Control, Manufacturer, Passenger, and Federal Aviation Administration. These direct hazards were associated with 36 root factors prepared for an error-elimination model using Fault Tree Analysis (FTA), a leading tool for System Safety experts. An FTA block-diagram model was created, followed by a probability simulation of accidents. Five case studies and reports were provided in order to fully demonstrate the usefulness of System Safety tools in promoting airline safety.

Lu, Chien-tsug↗
NASA NTRS1981

An overview of United States manned space flight from Mercury to the Shuttle

Technical considerations in the design, development and operation of United States manned spacecraft from Project Mercury to the Space Shuttle are reviewed. The design and mission philosophies, launch vehicle and spacecraft characteristics, mode of operation, flight results and influence on later programs are discussed for Project Mercury, and Gemini Apollo and Skylab programs, the Apollo-Soyuz Test Project and the Space Shuttle program. The Space Shuttle is shown to represent a major departure from the trend established in previous programs, requiring major advancements in the fields of flight control, thermal protection, and liquid-propellant rocket technology.

Faget, M. A.↗
NASA NTRS2012

A Communications Network for Cislunar Operations

Reliable and efficient communications will be critical to the success of commercial flight operations in cislunar space. The Internet is not well-suited to meeting this requirement. But the Delay-Tolerant Networking (DTN) architecture is. The DTN protocols are well-documented and implementations are mature. We think DTN will be ready to support low-cost, low-risk cislunar networking by the time the vehicles are in place.

network↗
NASA NTRS2011

Surveillance Range and Interference Impacts on Self-Separation Performance

Self-separation is a concept of flight operations that aims to provide user benefits and increase airspace capacity by transferring traffic separation responsibility from ground-based controllers to the flight crew. Self-separation is enabled by cooperative airborne surveillance, such as that provided by the Automatic Dependent Surveillance-Broadcast (ADSB) system and airborne separation assistance technologies. This paper describes an assessment of the impact of ADS-B system performance on the performance of self-separation as a step towards establishing far-term ADS-B performance requirements. Specifically, the impacts of ADS-B surveillance range and interference limitations were analyzed under different traffic density levels. The analysis was performed using a batch simulation of aircraft performing self-separation assisted by NASA s Autonomous Operations Planner prototype flight-deck tool, in two-dimensional airspace. An aircraft detected conflicts within a look-ahead time of ten minutes and resolved them using strategic closed trajectories or tactical open maneuvers if the time to loss of separation was below a threshold. While a complex interaction was observed between the impacts of surveillance range and interference, as both factors are physically coupled, self-separation performance followed expected trends. An increase in surveillance range resulted in a decrease in the number of conflict detections, an increase in the average conflict detection lead time, and an increase in the percentage of conflict resolutions that were strategic. The majority of the benefit was observed when surveillance range was increased to a value corresponding to the conflict detection look-ahead time. The benefits were attenuated at higher interference levels. Increase in traffic density resulted in a significant increase in the number of conflict detections, as expected, but had no effect on the conflict detection lead time and the percentage of conflict resolutions that were strategic. With surveillance range corresponding to ADS-B minimum operational performance standards for Class A3 equipment and without background interference, a significant portion of conflict resolutions, 97 percent, were achieved in the preferred strategic mode. The majority of conflict resolutions, 71 percent, were strategic even with very high interference (over three times that expected in 2035).

Idris, Husni↗
NASA NTRSDate not supplied

Evaluating the Use of High-Fidelity Simulator Research Methods to Study Airline Flight Crew Resilience

As it evolves, aviation will continue to require integration of a wide range of safety systems and practices, some of which are already in place and others that are yet to be developed. New concepts in system safety thinking have emerged to consider not only what may go wrong, but also what can be learned when things go right during commercial flight operations. Taken together, these complementary perspectives form a more comprehensive approach to systemsafety thinking that can help to recognize and preserve the resilient performance capabilities currently provided by humans. A need exists, however, for research methods to enable better understanding of the human contributions to aviation safety. NASA’s System-Wide Safety Project supports research on using flight simulation methods to study operator resilience and safety-producing behaviors. Building on prior NASA efforts investigating procedural non-adherences during area navigation standard terminal route arrivals, a high-fidelity commercial aviation line operational simulation (LOS) experiment has been designed to study how flight crews anticipate, monitor for, respond to, and learn from expected and unexpected disturbances during these operations. A diverse set of LOS scenarios were developed to simulate highly realistic, complex, but routinely encountered operational situations. Each scenario provided multiple opportunities to collect data on how flight crews manage threats and errors, as well as novel opportunities to observe resilient and safety-producing behaviors. The experimental design, implications for the study of safety-producing behaviors using simulation, and considerations for airline pilot training will be discussed.

Chad L Stephens↗
NASA NTRS2018

Air Traffic Management Technology Demonstration - 3 (ATD-3) Dynamic Weather Routes Domestic En Route Concept of Operations Synopsis Version 1.0

NASA conducted a survey in 2015 of stakeholders in industry, flight operators, and others to collect data on the most pressing air traffic management (ATM) issues impacting en route operations. Weather related delays and interruptions were identified as the most significant and costly problem impacting en route operations in today's system. Additionally, future traffic demands will place greater demands on the FAA's air traffic control system, necessitate a more efficient and integrated traffic management system and provide controller tools to leverage human productivity. Consequently, NASA is assembling a suite of integrated ground and aircraft-based technologies and decision-making aids under the Airspace Technology Demonstrations 3 (ATD-3) project to continuously search for more efficient weather-avoidance routes and to rapidly respond to weather changes and associated traffic management initiatives. These route efficiency enhancements are targeted at en route airspace and will enable continued use of en route and arrival metering in the presence of weather. NASA's Dynamic Weather Routes (DWR) concept represents a subset of those technologies and focuses primarily on the cruise phase of flight. It leverages existing air traffic weather, airspace, and traffic data, as well as improvements in navigation, surveillance, communication and digital network technologies, and builds upon existing ATM automation to address the shortcomings associated with strategic traffic flow management initiatives and weather forecasting uncertainties. The potential benefits in the form of time, fuel, and cost savings are significant. This concept of operations synopsis provides a detailed description of DWR, its potential benefits and notional implementation paths.

DWR↗
NASA NTRS1986

International cooperative study of aircrew layover sleep Operational summary

The findings of this cooperative study of layover sleep have direct implications for flight operations. In the consensus view of the principal investigators, these can be divided into their relevance for eastward or westward flight. Eastward flight produced more sleep disruption than westward. Different sleep and scheduling strategies are recommended for each flight direction, and the importance of individual crewmember factors is discussed in relation to age and circadian type. Despite the limitations of this study with regard to trip simplicity and the baseline data, the results for each airline are highly consistent and should be applicable to a wide range of long-haul crewmembers and carriers.

Graeber, R. Curtis↗
NASA NTRS1993

An operations concept methodology to achieve low-cost mission operations

Historically, the Mission Operations System (MOS) for a space mission has been designed last because it is needed last. This has usually meant that the ground system must adjust to the flight vehicle design, sometimes at a significant cost. As newer missions have increasingly longer flight operations lifetimes, the MOS becomes proportionally more difficult and more resource-consuming. We can no longer afford to design the MOS last. The MOS concept may well drive the spacecraft, instrument, and mission designs, as well as the ground system. A method to help avoid these difficulties, responding to the changing nature of mission operations is presented. Proper development and use of an Operations Concept document results in a combined flight and ground system design yielding enhanced operability and producing increased flexibility for less cost.

Ledbetter, Kenneth W.↗
NASA NTRS1993

Mission Operations and Command Assurance: Automating an Operations TQM Task

Mission Operations and Command Assurance (MO&CA) is a Total Quality Management (TQM) task on JPL projects to instill quality into mission operations. The mission operations environment is inherently risky because each decision made is potentially mission critical. The flight operations environment generally requires operators to make rapid critical decisions and solve problems based on limited information, while closely following standard procedures. MO&CA's primary goal is to help improve the operational reliability and reduce risk of projects during flight. To achieve this goal, automation of the MO&CA task is required. MO&CA specifically embodies the TQM principle of continuous process improvement (CPI) in which processes are continually examined and analyzed for opportunities for improvement. The second way in which MO&CA implements CPI on JPL projects is on new projects or upgrades to existing projects.

mission↗
NASA NTRS2005

SAFER Inspection of Space Shuttle Thermal Protection System

In the aftermath of the space shuttle Columbia accident, it quickly became clear that new methods would need to be developed that would provide the capability to inspect and repair the shuttle's thermal protection system (TPS). A boom extension to the Remote Manipulator System (RMS) with a laser topography sensor package was identified as the primary means for measuring the damage depth in acreage tile as well as scanning Reinforced Carbon- Carbon (RCC) surfaces. However, concern over the system's fault tolerance made it prudent to investigate alternate means of acquiring close range photographs and contour depth measurements in the event of a failure. One method that was identified early was to use the Simplified Aid For EVA Rescue (SAFER) propulsion system to allow EVA access to damaged areas of concern. Several issues were identified as potential hazards to SAFER use for this operation. First, the ability of an astronaut to maintain controlled flight depends upon efficient technique and hardware reliability. If either of these is insufficient during flight operations, a safety tether must be used to rescue the crewmember. This operation can jeopardize the integrity of the Extra-vehicular Mobility Unit (EMU) or delicate TPS materials. Controls were developed to prevent the likelihood of requiring a tether rescue, and procedures were written to maximize the chances for success if it cannot be avoided. Crewmember ability to manage tether cable tension during nominal flight also had to be evaluated to ensure it would not negatively affect propellant consumption. Second, although propellant consumption, flight control, orbital dynamics, and flight complexity can all be accurately evaluated in Virtual Reality (VR) Laboratory at Johnson Space Center, there are some shortcomings. As a crewmember's hand is extended to simulate measurement of tile damage, it will pass through the vehicle without resistance. In reality, this force will push the crewmember away from the vehicle, and could induce a moment which, if strong enough, could saturate the attitude control system in SAFER. This raises the concern that additional propellant will be consumed to maintain controlled flight. To account for this, the fidelity of the Virtual Reality simulation was improved to include the effect of crewmember contact with the vehicle during SAFER flight. In addition, while participating in VR simulations, the subject is in shirt sleeves and sits in a chair. This does not provide a flight-like representation of body position awareness. To prevent inadvertent contact with tile or RCC, other facilities were utilized to establish crew preferences for body attitude and tool configuration. Finally, a study was performed to determine if attitude constraints are needed for the Space shuttle and International Space Station to reduce SAFER flight difficulty.

Scoville, Zebulon C.↗