Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “model order reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Comparison of Sub-Ppm Instrument Response Suggests Higher Detection Limits Could Be Used to Quantify Methane Emissions from Oil and Gas Infrastructure

Quantifying and controlling fugitive methane emissions from oil and gas facilities remains essential for addressing climate goals, but the costs associated with monitoring millions of production sites remain prohibitively expensive. Current thinking, supported by measurement and simple dispersion modelling, assumes single-digit parts-per-million instrumentation is required. To investigate instrument response, the inlets of three trace-methane (sub-ppm) analyzers were collocated on a facility designed to release gas of known composition at known flow rates between 0.4 and 5.2 kg CH 4 h –1 from simulated oil and gas infrastructure. Methane mixing ratios were measured by each instrument at 1 Hertz resolution over nine hours. While mixing ratios reported by a cavity ring-down spectrometer (CRDS)-based instrument were on average 10.0 ppm (range 1.8 to 83 ppm), a mid-infrared laser absorption spectroscopy (MIRA)-based instrument reported short-lived mixing ratios far larger than expected (range 1.8 to 779 ppm) with a similar nine-hour average to the CRDS (10.1 ppm). We suggest the peaks detected by the MIRA are likely caused by a micrometeorological phenomenon, where vortex shedding has resulted in heterogeneous methane plumes which only the MIRA can observe. Further analysis suggests an instrument like the MIRA (an optical-cavity-based instrument with cavity size ≤10 cm3 measuring at ≥2 Hz with air flow rates in the order of ≤0.3 slpm at distances of ≤20 m from the source) but with a higher detection limit (25 ppm) could detect enough of the high-concentration events to generate representative 20 min-average methane mixing ratios. Even though development of a lower-cost, high-precision, high-accuracy instrument with a 25 ppm detection threshold remains a significant problem, this has implications for the use of instrumentation with higher detection thresholds, resulting in the reduction in cost to measure methane emissions and providing a mechanism for the widespread deployment of effective leak detection and repair programs for all oil and gas infrastructure.

03 NATURAL GAS↗
DOE OSTI2022

A New Search for Low-mass Dark Matter and an Examination and Reduction of the Uncertainty due to the Photoelectric Absorption Cross Section using a Cryogenic Silicon Detector with Single-charge Sensitivity

Many astrophysical observations point to the abundant existence of dark matter (DM) in the universe composed of particles beyond the Standard Model. However despite numerous experiments using different techniques, DM particles have yet to be directly observed. The Super Cryogenic Dark Matter Search (SuperCDMS) SNOLAB experiment will employ silicon and germanium crystal detectors operated at temperatures as low as 15~mK to probe DM interactions using phonon and ionization signals. Recently, R\&D; facilities have developed gram-sized high-voltage eV-scale (HVeV) silicon detectors that achieve single-electron-hole-pair resolution. By probing effective DM-electron interactions, these devices can be used for searches of low-mass DM candidates.This dissertation presents a DM search experiment known as HVeV Run~2 that employs a second-generation HVeV detector operated in an above-ground laboratory at Northwestern University (IL, USA). Energy spectra are obtained from a blind analysis with 0.39 and 1.2\,g-days of exposure with the detector biased at 60 and 100\,V, respectively. The 0.93~gram detector achieves a 3\,eV phonon energy resolution, corresponding to a world-leading charge resolution of 3\,\% of a single electron-hole pair for a detector bias of 100\,V. With charge carrier trapping and impact ionization effects incorporated into the DM signal models, the resulting exclusion limits are reported for inelastic DM-electron scattering for DM masses from 0.5--$10^{4}$\,MeV$/c^{2}$; in the mass range from 1.2--50\,eV$/c^{2}$ the limits for dark photon and axion-like particle absorption are reported.Several DM search experiments, including HVeV Run~2, are sensitive to low-mass DM candidates that rely on the temperature-dependent photoelectric absorption cross section of silicon. However discrepancies in the underlying literature data result in dominating systematic uncertainties on the DM exclusion limits. In order to reduce these systematic uncertainties, this dissertation presents a novel method of making a direct, low-temperature measurement of the photoelectric absorption cross section of silicon at energies near the band gap (1.2--2.8\,eV).

Wilson, Matthew James↗
DOE OSTI2024

Bayesian reduced-order deep learning surrogate model for dynamic systems described by partial differential equations

We propose a reduced-order deep-learning surrogate model for dynamic systems described by time-dependent partial differential equations. This method employs space–time Karhunen–Loève expansions (KLEs) of the state variables and space-dependent KLEs of space-varying parameters to identify the reduced (latent) dimensions. Subsequently, a deep neural network (DNN) is used to map the parameter latent space to the state variable latent space. An approximate Bayesian method is developed for uncertainty quantification (UQ) in the proposed KL-DNN surrogate model. The KL-DNN method is tested for the linear advection–diffusion and nonlinear diffusion equations, and the Bayesian approach for UQ is compared with the deep ensembling (DE) approach, commonly used for quantifying uncertainty in DNN models. It was found that the approximate Bayesian method provides a more informative distribution of the PDE solutions in terms of the coverage of the reference PDE solutions (the percentage of nodes where the reference solution is within the confidence interval predicted by the UQ methods) and log predictive probability. The DE method is found to underestimate uncertainty and introduce bias. For the nonlinear diffusion equation, we compare the KL-DNN method with the Fourier Neural Operator (FNO) method and find that KL-DNN is 10% more accurate and needs less training time than the FNO method.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Multi-Model and Multi-Scale Global Sensitivity Analysis for Identifying Controlling Processes of Complex Systems

An environmental model consists of multiple process level sub-models, and each sub-model represents a process that is key to the operation of the simulated system. Global sensitivity analysis methods have been widely used to identify important processes for system model development and improvement. The existing methods of global sensitivity analysis only consider parametric uncertainty, and are not capable of handling model uncertainty caused by multiple process models that arise from competing hypotheses about one or more processes. To address this problem, this project develops a new method to probe model output sensitivity to competing process models by integrating model averaging methods with variance-based global sensitivity analysis to address uncertainty in process models and parameters. The new method yields three process sensitivity indices. The first one is called first-order process sensitivity index, and it is derived as a single summary measure of relative process importance. Evaluating the index is computationally expensive, because it relies in a Monte Carlo scheme that requires thousands and even millions of model executions. To reduce computational cost, this project develops a computationally efficient, quasi Monte Carlo method, and this method is presented in Chapter 2 of this report with and a numerical example for demonstration. The numerical example shows that the results of the quasi Monte Carlo method are substantially close to those of the full Monte Carlo method, but the computational cost of the quasi Monte Carlo method is only 0.7% of that of the full Monte Carlo method. The second index is called total-effect process sensitivity index, and it measures interactions between different processes. Therefore, this sensitivity index includes the first-order process sensitivity index, and can be used to identify influential processes. On the other hand, the total-effect process sensitivity index can also be used to screen non-influential processes. This is demonstrated by two numerical examples using the Sobol-G* functions and groundwater flow models that consider recharge process, geological process, and snowmelt process. The numerical examples shows that the total-effect process sensitivity index is more informative than the first-order process sensitivity. The derivation of the process sensitivity index and the numerical examples are discussed in Chapter 3. Chapter 4 presents two computationally efficient methods for screening non-influential processes to exclude them from further investigation. The two methods are the multi-model difference-based sensitivity (MMDS) analysis method, which can be implemented using the Latin Hypercube Sampling. The second one is the implementation of MMDS method using a binning method. The numerical example for the Sobol-G* function indicates the two methods are capable of identifying non-influential models, and the numerical examples for the groundwater flow and reactive transport show that the two methods are effective for groundwater problems. However, it should be noted that the two methods are numerical approximations, and they can only be used for screening non-influential processes, not for ranking importance of system processes. All the sensitivity analysis methods are implemented by developing python codes, and the codes are in a software called SAMMPY: a python package for process sensitivity analysis under multiple models. The SAMMPY design and structure are discussed in Chapter 5, and the package is released to the public for free download.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Latent Twins

Over the past decade, scientific machine learning has transformed the development of mathematical and computational frameworks for analyzing, modeling, and predicting complex systems. From inverse problems to numerical partial differential equations (PDEs), dynamical systems, and model reduction, these advances have pushed the boundaries of what can be simulated. Yet they have often progressed in parallel, with representation learning and algorithmic solution methods evolving largely as separate pipelines. With Latent Twins, we propose a unifying mathematical framework that creates a hidden surrogate in latent space for the underlying equations. Whereas digital twins mirror physical systems in the digital world, Latent Twins mirror mathematical systems in a learned latent space governed by operators. Through this lens, classical modeling, inversion, model reduction, and operator approximation all emerge as special cases of a single principle. We establish the fundamental approximation properties of Latent Twins for both ordinary differential equations (ODEs) and PDEs and demonstrate the framework across three representative settings: (i) canonical ODEs, capturing diverse dynamical regimes; (ii) a PDE benchmark using the shallow-water equations, contrasting Latent Twin simulations with deep operator network and forecasts with a four-dimensional variational method baseline; and (iii) a challenging real-data geopotential reanalysis dataset, reconstructing and forecasting from sparse, noisy observations. Latent Twins provide a compact, interpretable surrogate for solution operators that evaluate across arbitrary time gaps in a single-shot, while remaining compatible with scientific pipelines such as assimilation, control, and uncertainty quantification. Looking forward, this framework offers scalable, theory-grounded surrogates that bridge data-driven representation learning and classical scientific modeling across disciplines.

Latent Twins↗
DOE OSTI2023

Functional variability in specific root respiration translates to autotrophic differences in soil respiration in a temperate deciduous forest

CO 2 release from forest soils (R s ) is a prominent flux in the global carbon cycle. Rs is derived from roots (autotrophic respiration, R a ) and microbial (heterotrophic) respiration and is highly dynamic, as it depends on edaphic and environmental conditions as well as root functional traits and microbial community composition. It is unclear how root functional traits affect root and microbial respiration rates; however, their consideration may help parse out the relative contributions of root and microbial respiration to R s . At a temperate forest site, root systems of 3–4 functional root orders and their surrounding surface soil were carefully excavated and placed into custom trays designed to repeatedly measure R s in situ on eight temperate tree species that varied in their root functional strategies and mycorrhizal affinity. R s was measured bi-weekly to monthly for nearly one year using a custom chamber attached to a gas exchange system. R s varied over time, ranging from 0.3 to 12 µmol m -2 s -1 . Comparable root systems of the same species were excised from the soil and specific root respiration rates (R r ) were measured. Rr ranged from 2.5 to 9.0 nmol g -1 s -1 and was negatively correlated with root tissue density and positively related to root tissue nitrogen concentration. Using R r to estimate R a , we estimate that R a accounts for <10%, on average 2–3%, of R s for individual root systems (averaging 1.2 g dry biomass) housed in surrounding soil (average 1.3 kg dry mass) in situ; thus, Ra was roughly 20 times greater than Rh per unit mass. The contribution of R a peaked in the fall and coincided with leaf senescence of the forest canopy. A soil-sterilizing experimental treatment designed to help isolate R a in situ reduced bacterial biomass and shifted fungal community composition, but there was no reduction in Rs of the in-situ root-soil tray systems. The relative R a to R s ratio increased with root functional strategies characterized by greater specific root length and tip abundance, but also to greater root tissue density. The ratio of R a to R s also increased with warmer soil temperatures and decreased slightly with increasing soil moisture. We discuss how incorporating root functional traits as modulators of the autotrophic contribution to R s could be considered when modeling total soil CO 2 efflux from forests.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Application of Sequential Design of Experiments (SDoE) to Large Pilot-Scale Solvent-Based CO2 Capture Process at Technology Centre Mongstad (TCM)

The United States Department of Energy’s Carbon Capture Simulation for Industry Impact (CCSI2) program has developed a framework for sequential design of experiments (SDoE) that aims to maximize knowledge gained from budget- and schedule-limited pilot scale testing. SDoE was applied to the planning and execution of campaigns for testing CO2 capture systems at pilot-scale in order to optimally allocate resources available for the testing. In this methodology, a stochastic process model is developed by quantifying the parametric uncertainty in submodels of interest; for a solvent-based CO2 capture system, these may include physical properties and equipment performance submodels (e.g., mass transfer, interfacial area). This uncertainty is propagated through the full process model, over variable operating conditions, for estimating the resulting uncertainty in key model outputs (e.g., percentage of CO2 capture, solvent regeneration energy requirement). In developing a data collection plan, the predicted output uncertainty is incorporated into an algorithm that seeks simultaneously to select process operating conditions for which the predicted uncertainty is relatively high and to ensure that the entire space of operation is well represented. This test plan is then used to guide operation of the pilot plant at varying steady-state conditions, with resulting process data incorporated into the existing model using Bayesian inference to refine parameter distributions. The updated stochastic model, with reduced parametric uncertainty from data collected, is then used to guide additional data collection, thus the sequential nature of the experimental design. The SDoE process was implemented at the pilot test unit (12 MWe in scale) at Norway’s Technology Centre Mongstad (TCM) in a summer 2018 test campaign with aqueous monoethanolamine (MEA). During the test campaign, the varied operating conditions included the flowrates of circulated solvent, flue gas, and reboiler steam and the CO2 concentration in the flue gas. The process data were used to update probability distributions of mass transfer and interfacial area parameters of a stochastic process model developed by the CCSI2 team. Two iterations of the SDoE process were executed, resulting in the uncertainty in model predicted CO2 capture percentage decreasing by an average of 58.0 ± 4.7% over the full input space of interest. This work demonstrates the potential of the SDoE process for model refinement through reduction in process model parametric uncertainty, and ultimately risk in scale-up, in CO2 capture technology performance.

carbon capture↗
DOE OSTI2021

Above-ground net primary productivity in regenerating seasonally dry tropical forest: Contributions of rainfall, forest age and soil

Identifying factors controlling forest productivity is critical to understanding forest-climate change feedbacks, modelling vegetation dynamics and carbon finance schemes. However, little research has focused on productivity in regenerating tropical forests which are expanding in their fraction of global area have an order of magnitude larger carbon uptake rates relative to older forest. Here We examined above-ground net primary productivity (ANPP) and its components (wood production and litterfall) over 10 years in forest plots that vary in successional age, soil characteristics and species composition using band dendrometers and litterfall traps in regenerating seasonally dry tropical forests in northwestern Costa Rica. We show that the components of ANPP are differentially driven by age and annual rainfall and that local soil variation is important. Total ANPP was explained by a combination of age, annual rainfall and soil variation. Wood production comprised 35% of ANPP on average across sites and years, and was explained by annual rainfall but not forest age. Conversely, litterfall increased with forest age and soil fertility yet was not affected by annual rainfall. In this region, edaphic variability is highly correlated with plant community composition. Thus, variation in ecosystem processes explained by soil may also be partially explained by species composition. These results suggest that future changes in annual rainfall can alter the secondary forest carbon sink, but this effect will be buffered by the litterfall flux which varies little among years. In determining the long-term strength of the secondary forest carbon sink, both rainfall and forest age will be critical variables to track. We also conclude that detailed understanding of local site variation in soils and plant community may be required to accurately predict the impact of changing rainfall on forest carbon uptake. Synthesis. We show that in seasonally dry tropical forest, annual rainfall has a positive relationship with the growth of above-ground woody tissues of trees and that droughts lead to significant reductions in above-ground productivity. These results provide evidence for climate change—carbon cycle feedbacks in the seasonal tropics and highlight the value of longitudinal data on forest regeneration.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Plant-specific Model and Data Analysis using Dynamic Security Modeling and Simulation

The requirements for U.S. nuclear power plants to maintain a large on-site physical security force contribute to their high operational costs. The cost of maintaining the current physical security posture is approximately 10% of the overall operation and maintenance budget for commercial nuclear power plants. The goal of the Light Water Reactor Sustainability (LWRS) program’s physical security pathway is to develop tools, methods, and technologies and provide the technical basis for an optimized physical security posture. The conservatisms built into current security postures may be analyzed and minimized in order to reduce security costs while still ensuring adequate security and operational safety. The research performed at Idaho National Laboratory within LWRS program’s physical security pathway has successfully developed a dynamic force-on-force modeling framework using various computer simulation tools and integrating them with the dynamic assessment Event Modeling Risk Assessment using Linked Diagrams (EMRALD) tool. This document provides an update on the progress in applying a dynamic computational framework that links results from a commercially available force-on-force simulation tool, a commercially available thermal-hydraulic tool, and EMRALD to an operating commercial nuclear power plant. This report is only a summary of the progress and does not contain specific modeling results as those contain sensitive security information. This process of including plant procedures and multiple analysis results is being called Modeling and Analysis for Safety Security using Dynamic EMRALD Framework or MASS-DEF. Previous reports described how a user could integrate their plant-specific force-on-force models with the dynamic simulation tool EMRALD, model operator actions, integrate with probabilistic risk assessment tools, such as CAFTA (Computer Aided Fault Tree Analysis System) or SAPHIRE (Systems Analysis Programs for Hands-on Integrated Reliability Evaluations), and with thermal-hydraulic tools, such as RELAP-5. Previous reports applied various combinations of available simulations codes with EMRALD using generic plant models to demonstrate how to perform the analysis. This report documents the results of applying the dynamic computational framework to an actual nuclear facility using their security scenarios and timelines. This report does not contain any plant's sensitive information and/or Safeguards Information. The purpose of this study was to verify that results achieved using generic models are similar to actual plant results and to refine our guidance on the use of the framework. This assessment enables further analysis, such as what-if scenarios and staff-reduction evaluation, thereby optimizing physical security at plants.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI1968

Kryptonate Hydrogen Detection System (Final Report)

A prototype model of a multipurpose instrument which demonstrates the applicability of the Kryptonate® technique for detecting hydrogen gas was developed. This report describes the construction of the instrument and presents a laboratory evaluation of its performance. Performance was excellent. The instrument was designed to detect hydrogen in air at concentrations of 0-3% by volume, and to detect hydrogen in nitrogen or other inert gas at concentrations of 0-10% by volume. Other detection levels (both higher and lower) could be set if required. Ultimate response times can be made of the order of 0.5 seconds. The instrument is an all solid state device operating from 120V 60 Hz power source. The instrument has been designed to enable modifications to be made with a minimum amount of difficulty.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Constraint energy minimizing generalized multiscale finite element method for multi-continuum Richards equations

In fluid flow simulation, the multi-continuum model is a useful strategy. When the heterogeneity and contrast of coefficients are high, the system becomes multiscale, and some kinds of reduced order methods are demanded. Combining these techniques with nonlinearity, we will consider in this paper a dual-continuum model which is generalized as a multi-continuum model for a coupled system of nonlinear Richards equations as unsaturated flows, in complex heterogeneous fractured porous media; and we will solve it by a novel multiscale approach utilizing the constraint energy minimizing generalized multiscale finite element method (CEM-GMsFEM). In particular, such a nonlinear system will be discretized in time and then linearized by Picard iteration (whose global convergence is proved theoretically). Subsequently, we tackle the resulting linearized equations by the CEM-GMsFEM and obtain proper offline multiscale basis functions to span the multiscale space (which contains the pressure solution). More specifically, we first introduce two new sources of samples, and the GMsFEM is used over each coarse block to build local auxiliary multiscale basis functions via solving local spectral problems, that are crucial for detecting high-contrast channels. Second, per oversampled coarse region, local multiscale basis functions are created through the CEM as constrainedly minimizing an energy functional. Various numerical tests for our approach reveal that the error converges with the coarse-grid size and that only few oversampling layers as well as basis functions are needed.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Calculating Potential Radiological Emissions for Waste Management Activities at INL - 20068

At Idaho National Laboratory (INL), work involving radionuclides is evaluated for potential emissions from a project in order to comply with the National Emission Standards for Hazardous Air Pollutants (NESHAP) regulations, 40 CFR 61 Subpart H. Emission calculations are documented in an Air Permitting Applicability Determination (APAD) to analyze unmitigated and mitigated emissions and determine if an Application to Construct (ATC) or continuous monitoring is required. To calculate the unmitigated and mitigated emissions, a spreadsheet was developed to provide ease in determining potential emissions by providing the maximum operating temperature and the material being used. The spreadsheet aids in determining the potential emissions for research projects and waste management activities at Materials and Fuels Complex (MFC) and other locations across the INL site. Furthermore, it can also be used for periodic confirmatory measurements (PCM) to justify low emissions. Elements that factor into the unmitigated and mitigated calculations include the amount of each radionuclide used (in curies or grams), specific activity (if amount is given in grams), the temperature the material is heated to in Celsius, the dose conversion factor which is derived from Clean Air Act Assessment Package - 1988 (CAP-88) modeling, and the number of HEPA filters used for mitigated measures. The main drivers for calculating the unmitigated emissions for a project are the amount used per radionuclide, the maximum operating temperature, and the location of the work. The maximum operating temperature determines the airborne release factor which is dependent on the physical state of the radionuclide. Prior to October 2017, if the radionuclide was heated to greater than 100 deg. C, the radionuclide was assumed to be a gas, which has the highest airborne release factor. This assumption would be overly conservative for radionuclides with high melting and boiling points, which provided a challenge to demonstrate low emissions. In October 2017, the Environmental Protection Agency (EPA) approved an alternative method for INL. This method allows the airborne release factor to be determined by using the melting point and 90% of the boiling point of the radionuclide. This methodology was included in the spreadsheet to allow unmitigated emission calculations for APADs to be completed more efficiently and effectively. Results show a reduction in time completing air emission calculations as well as lower total emissions across all facilities at INL. MFC annual emissions were reduced by 62% from the previous year and Research and Education Campus (REC) facilities were reduced by 38% due to implementation of the approved alternative method. Time spent on APADs, PCMs, and documentation for the annual NESHAP report was also reduced significantly. The spreadsheet provided in Table I provides the potential emission calculations for the 'Advanced Retrieval and Disposition Techniques for Remote Handled Mixed Low Level Waste (RH MLLW) at the Radioactive Scrap and Waste Facility (RSWF)' project. Calculations show the Potential Effective Dose Equivalent (PEDE) at RSWF to be 7.27 E-04 mrem/yr (7.27 E-09 Sv/yr) which is well below the 0.1 mrem/yr threshold. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Investigating Secondary Aerosol Processes in the Amazon through Molecular-level Characterization of Semi-Volatile Organics

In areas where biogenic emissions are oxidized in the presence of anthropogenic pollutants, it has become increasingly apparent that secondary organic aerosol (SOA) formation from biogenic volatile organic compounds (BVOCs) is substantially enhanced. The Amazon forest is the dominant source of BVOCs globally, and the forest is rapidly being converted to urban and agricultural uses. We participated in a collaborative field study located in the Amazon region around Manaus, Brazil, in 2014 (Green Ocean Amazon; GoAmazon). This study was designed to comprehensively examine how BVOC emissions (specifically, the most highly emitted non-methane hydrocarbon, isoprene, and lesser studied sesquiterpenes) and their interaction with anthropogenic pollution (i.e., nitrogen oxides, sulfur dioxide, and black carbon) alter the atmosphere’s oxidative capacity, influence secondary aerosol formation, atmospheric composition and, ultimately, affect the earth’s radiation balance and climate. We provide the first hourly, in-situ measurement of 30 sesquiterpenes and 4 diterpenes, roughly estimating that sesquiterpene oxidation contributes to 10-14% of ozone reactive loss by terpenes and at least 0.4–5% (median 1 %) of total submicron OA mass. However, this is likely a low-end estimate, as evidence for additional unaccounted sesquiterpenes and their oxidation products clearly exists. We also provide new perspectives on sulfate, NO x , and particle acidity influencing isoprene-derived SOA, comparing the central Amazon environment with Southeastern U.S.A. summer, representing clean to polluted conditions, respectively. We find that summed concentrations of isoprene-derived SOA tracers correlated with particulate sulfate spanning three orders of magnitude, suggesting that 1 μg m -3 reduction in sulfate corresponds with at least ~0.5 μg m -3 reduction in isoprene-derived SOA. We also find that SOA mass derived from isoprene oxidation in the presence of NO x is primarily comprised of aerosol sulfate bound with isoprene oxidation products (i.e. organosulfates), ~97% in the Amazon and ~55% in the Southeastern U.S. We infer under natural conditions in high isoprene emission regions, preindustrial aerosol sulfate was almost exclusively isoprene-derived organosulfates, which are traditionally thought as representative of anthropogenic influence. We further report the first field observations showing that particle acidity impacts the distribution of isoprene oxidation tracers in the gas and particle phases, providing physicochemical insight into isoprene SOA formation chemistry. Coupled with other co-located measurements by the DOE Atmospheric Radiation Measurement (ARM) team and collaborating PIs at our measurement site (called T3), on the G1 aircraft, and at additional field sites (T0, T1, T2) this data set has been used to understand emission, oxidation, and particle formation pathways at the molecular level, to elucidate how these pathways change when influenced by anthropogenic sources, and to evaluate their importance for the atmospheric budget of aerosols and the earth’s radiation balance on regional scales. Recommendations: Further constraint of the role of sesquiterpenes on ozone (O 3 ) reactivity and SOA formation is limited by the availability of authentic standards and synthesized compounds of sesquiterpenes and their oxidation products. Future research efforts should focus on making such standards available via custom synthesis to allow for accurate quantification and focused oxidation experiments that will fully elucidate the chemistry of these compounds in the atmosphere. Further, reductions in aerosol sulfate (via SO 2 emissions control) continues to be one of the most effective methods to reduce SOA formation from isoprene, but the concerted role of ammonia (NH 3 ) gas emissions from (agricultural) industry and other sources requires more investigation to better understand the role of aerosol acidity in SOA formation and potential controls. As GoAmazon particles can be more acidic compared to areas with greater anthropogenic NH 3 emissions, this promotes relatively greater organosulfate (OS) formation from isoprene even in the presence of NO x . Because OS and inorganic sulfate differ in water uptake properties, this implies preindustrial aerosol sulfate (albeit less abundant) may have been less reflective than current earth system models assume. Further research should investigate the radiative impacts of organic vs inorganic sulfate in aerosols to improve model representation. Finally, future work (currently underway) should include constraint of the contributions of monoterpene (C 10 H 16 ) BVOCs and biomass burning VOCs as precursors to SOA formation in the region as well as their impacts on radiative forcing in the climate system.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

A comprehensive and synthetic dataset for global, regional, and national greenhouse gas emissions by sector 1970–2018 with an extension to 2019

To track progress towards keeping global warming well below 2 °C or even 1.5 °C, as agreed in the Paris Agreement, comprehensive up-to-date and reliable information on anthropogenic emissions and removals of greenhouse gas (GHG) emissions is required. Here we compile a new synthetic dataset on anthropogenic GHG emissions for 1970–2018 with a fast-track extension to 2019. Our dataset is global in coverage and includes CO 2 emissions, CH 4 emissions, N 2 O emissions, as well as those from fluorinated gases (F-gases: HFCs, PFCs, SF 6 , NF 3 ) and provides country and sector details. We build this dataset from the version 6 release of the Emissions Database for Global Atmospheric Research (EDGAR v6) and three bookkeeping models for CO 2 emissions from land use, land-use change, and forestry (LULUCF). We assess the uncertainties of global greenhouse gases at the 90 % confidence interval (5th–95th percentile range) by combining statistical analysis and comparisons of global emissions inventories and top-down atmospheric measurements with an expert judgement informed by the relevant scientific literature. We identify important data gaps for F-gas emissions. The agreement between our bottom-up inventory estimates and top-down atmospheric-based emissions estimates is relatively close for some F-gas species (~ 10 % or less), but estimates can differ by an order of magnitude or more for others. Our aggregated F-gas estimate is about 10 % lower than top-down estimates in recent years. However, emissions from excluded F-gas species such as chlorofluorocarbons (CFCs) or hydrochlorofluorocarbons (HCFCs) are cumulatively larger than the sum of the reported species. Using global warming potential values with a 100-year time horizon from the Sixth Assessment Report by the Intergovernmental Panel on Climate Change (IPCC), global GHG emissions in 2018 amounted to 58 ± 6.1 GtCO 2 eq. consisting of CO 2 from fossil fuel combustion and industry (FFI) 38 ± 3.0 GtCO 2 , CO 2 -LULUCF 5.7 ± 4.0 GtCO 2 , CH 4 10 ± 3.1 GtCO 2 eq., N2O 2.6 ± 1.6 GtCO 2 eq., and F-gases 1.3 ± 0.40 GtCO 2 eq. Initial estimates suggest further growth of 1.3 GtCO 2 eq. in GHG emissions to reach 59 ± 6.6 GtCO 2 eq. by 2019. Our analysis of global trends in anthropogenic GHG emissions over the past 5 decades (1970–2018) highlights a pattern of varied but sustained emissions growth. There is high confidence that global anthropogenic GHG emissions have increased every decade, and emissions growth has been persistent across the different (groups of) gases. There is also high confidence that global anthropogenic GHG emissions levels were higher in 2009–2018 than in any previous decade and that GHG emissions levels grew throughout the most recent decade. While the average annual GHG emissions growth rate slowed between 2009 and 2018 (1.2 % yr –1 ) compared to 2000–2009 (2.4 % yr –1 ), the absolute increase in average annual GHG emissions by decade was never larger than between 2000–2009 and 2009–2018. Our analysis further reveals that there are no global sectors that show sustained reductions in GHG emissions. There are a number of countries that have reduced GHG emissions over the past decade, but these reductions are comparatively modest and outgrown by much larger emissions growth in some developing countries such as China, India, and Indonesia. There is a need to further develop independent, robust, and timely emissions estimates across all gases. As such, tracking progress in climate policy requires substantial investments in independent GHG emissions accounting and monitoring as well as in national and international statistical infrastructures. The data associated with this article (Minx et al., 2021) can be found at https://doi.org/10.5281/zenodo.5566761.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Reducing uncertainty of polar to midlatitude linkages using DOE’s E3SM in a coordinated model-experiment setting

This project brought DOE’s climate modeling effort with the Energy Exascale Earth System Model into the Polar Amplification Model Intercomparison Project (PAMIP), which is part of the sixth and latest Coupled Model Intercomparison Project, CMIP6. PAMIP examines the causes and consequences of polar amplification, when external forcing results in a larger temperature increase in high latitudes than the global average, in a coordinated set of model experiments with a common modeling protocol. Our teams from UC Irvine and the University of Toronto have designed, carried out, analyzed, and disseminated PAMIP output from the Energy Exascale Earth System Model (E3SM) and the Community Earth System Model (CESM). PAMIP’s ongoing stream of significant new results have advanced progress in the community’s understanding and led to new outstanding research questions that have motivated further work. PAMIP has led to improved consensus on the atmospheric response to sea ice loss. The important finding is that for a similar sea ice anomaly forcing, the simulated atmospheric response in the troposphere is remarkably consistent among the 16 models’ runs analyzed. The zonal-mean tropospheric response consists of a very robust equatorward shift of the westerly flow in mid-latitudes. However, while the multi-model mean response is robust, it has a weak amplitude relative to internal variability. We identified a weakness in the models (including E3SM) in terms of their response to sea-ice forcing that is related to eddy forcing (or nonlinear dynamical effects) at mid- to high latitudes. In fact, E3SM is an outlier in terms of the models participating, and in that sense, it turned out to be a vital participant model. We found that reductions in energy transport due sea-ice loss and involving dry air only are compensated by increases in moist energy transport from warmer sea surface temperature in midlatitudes. This leads to a large spread in energy transport into the Arctic and is a potential source of spread in Arctic amplification. We identified an important role that climate modes, including tropical modes of variability (El Nino and the Southern Oscillation (ENSO); the Quasi-biennial Oscillation (QBO)) play in the response to sea-ice anomalies, including in ocean coupled experiments. Similarly, we identified and quantified the contribution of sea-ice thickness to the atmospheric response compared to the response to sea-ice extent only. We found that it is important to run large ensembles and even with an ensemble size of 100 simulations the response is largely influenced by internal variability. We demonstrated convincingly that Ural blocking, not sea-ice loss, provides the weakening of the stratospheric polar vortex in fall/early winter and a negative phase of the North Atlantic Oscillation that can last for up to two months. However, sea-ice anomalies can influence the background flow so that the response to Ural blocking is more persistent under low sea-ice conditions in the Barents/Kara Sea than high sea ice Atmospheric model hierarchies that progressively add individual processes have a long history in providing dynamical insight for modeling the atmosphere. Similarly, coupled model hierarchies that progressively add individual ocean processes can provide insights into the workings of the coupled climate system, however such hierarchies have not been available except for a non-dynamical slab ocean model. Because of the missing processes, surface flux corrections must be added to produce a target climate. In this project, we managed to overcome this problem and develop a globally coupled ocean model hierarchy in CESM that can turn on and off the processes of mixed-layer entrainment and Ekman flow. We used the hierarchy to study the impact of Arctic sea-ice loss on the climate system. We find that the effect of mixed-layer entrainment on ocean heat uptake influences the atmospheric circulation by shifting the latitudinal positions of the mid-latitude westerly jet and the Intertropical Convergence Zone (ITCZ). In quadrupled CO 2 experiments, we studied how air-sea coupling affects the response of tropical rainfall under global warming. In order to identify the importance of individual ocean processes, we used the hierarchy of ocean models to separate the effects of seasonal mixed-layer entrainment, wind-driven Ekman flows, and frictional flows. We showed that including Ekman and frictional flows allows our simulation to produce the Pacific Ocean's enhanced equatorial warming pattern and equatorward ITCZ contraction noted in previous climate simulations. We also showed that the frictional flow, which has yet to receive much attention, is as important as the Ekman flow in generating equatorial heat convergence.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

High-Fidelity and High-Performance Computational Simulations for Rapid Design Optimization of Sulfur Thermal Energy Storage

Industrial process heating (IPH) accounts for approximately 70% of US manufacturing energy use and is primarily produced by fossil fuel combustion. Approximately 1500 TWht (approximately 60%) of IPH demand is in the temperature range of 100-300. Industrial applications in this temperature range include drying, hydrothermal processing, thermal enhanced oil recovery, food and beverage, bioethanol production, etc. Cost-effective thermal energy storage (TES) that increases the utilization of waste and renewable heat (solar, geothermal, etc.) could provide significant energy savings and reliable heat sources, decrease emissions, and increase US manufacturing competitiveness through reductions in fuel consumption. TES development has historically been dominated by technologies suitable for deployment with concentrating solar power (CSP). State-of-the-art thermal storage deployed commercially with power tower CSP plants uses a 60%/40% NaNO3/KNO3 molten salt and operates between temperatures of approximately 280 degrees Celsius and 570 degrees Celsius using a two-tank configuration. However, these nitrate salts are unsuitable for operation outside of this temperature range due to a high freezing point of approximately 220 degrees Celsius, and limits on high-temperature salt stability and corrosion resistance of containment alloys. Other materials being investigated for TES include those based on: (1) sensible energy storage (various molten salt compositions, inert solid particles, rocks or pebble beds, sulfur, water, concrete, graphite, etc.), (2) latent energy storage in materials that undergo solid-liquid phase change at relevant temperatures (organic materials for low-temperature applications, inorganic salts and/or metals for high-temperature applications), or (3) thermochemical energy storage (hydrides, hydroxides, carbonates, metal oxides, etc.). The application temperature and challenges pertaining to storage material and/or containment cost, energy density, long-term thermal and cyclic stability, and charge/discharge heat transfer effectiveness drive material selection for a given IPH or electricity generation application. Sulfur is a cheap commodity at $80/ton compared to $1100 - 1300/ton for conventional salts. When using a metric of storage cost per kWh, sulfur costs around 2-3 $/kWh. Previous sulfur TES development focused on high temperature (>600 degrees) concentrated solar power applications with sulfur encapsulated in pipes and flow of gaseous HTF (air) in the shell side. However, for lower-temperature IPH applications in the range of approximately 100-300 degrees Celsius Element 16 adopted a compact and scalable TES design with molten sulfur in the shell and HTF pipes submerged in the molten sulfur bath. The low-cost molten sulfur TES for dispatchable IPH has deployment potential for broad applications. The spatial and temporal evolution of the HTF and sulfur temperature is critical to the TES system performance, and thus detailed modeling can improve understanding of the performance and facilitate design improvements. Using high performance computing and computational fluid dynamics (CFD) a low-cost molten sulfur thermal energy storage (TES) system for industrial process heating (IPH) applications was developed. The unique challenges in CFD modeling of sulfur TES are the sharp property changes of sulfur relevant to the working temperatures. Above 159, liquid sulfur undergoes polymerization, and the viscosity of sulfur rapidly increases by several orders of magnitude between 159 degrees Celsius and 188 degrees Celsius, followed by a decrease in viscosity beyond 188 degrees Celsius due to thermal bound dissociation. In addition, various concentrations of H2S impurities can also modify sulfur viscosity. This numerical challenge is especially relevant to transient simulation of the sulfur TES charging and discharging processes as the extreme property variations limit the applicability of traditional heat transfer correlations. Transient CFD simulations including the temperature-dependent sulfur properties and geometric complexity of the TES design were used to predict the effect of natural convection during charging and discharging on the heat transfer process, sulfur temperature uniformity, charge/discharge rates, and performance of the storage devices. The CFD model was validated with experimental results for a full charge and discharge cycle. The work will show 3D and 2D simulation comparisons aimed to facilitate rapid design iterations and a machine learning based design optimization approach.

CFD↗
DOE OSTI2022

Numerical analysis of soot emissions from gasoline-ethanol and gasoline-butanol blends under gasoline compression ignition conditions

In the present work, computational fluid dynamics (CFD) simulations of a single-cylinder gasoline compression ignition (GCI) engine were performed to investigate the impact of blending two biofuels, ethanol and n-butanol, with gasoline on the trade-off between combustion phasing and soot emissions under low load conditions. Here, in order to represent market gasoline (RD5-87), a four-component toluene primary reference fuel (TPRF) + ethanol (ETPRF) surrogate (with 20% ethanol by mole; E20) was formulated using a neural network based octane predictor such that the surrogate had the same ethanol content, Research Octane Number (RON) and Octane Sensitivity (S). In addition, a novel skeletal kinetic mechanism for ETPRF and TPRF + n-butanol (BTPRF) blends, incorporating polycyclic aromatic hydrocarbon (PAH) chemistry, was developed. A three-dimensional (3D) engine CFD formulation employing the skeletal mechanism, adaptive mesh refinement (AMR), finite-rate chemistry approach, and hybrid method of moments (HMOM) was adopted to capture the in-cylinder combustion phenomena and soot emissions. The engine CFD model was validated against RD5-87 experimental data for a broad range of start-of-injection (SOI) timings (-21/-27/-36/-45 crank angle degrees (CAD) after top-dead center (aTDC)), with respect to in-cylinder pressure, heat release rate, combustion phasing, and soot emissions. The closed-cycle simulation results were analyzed to elucidate the non-monotonic trend of soot emissions versus SOI timing: SOI-36 > SOI-45 > SOI-21 > SOI-27. Thereafter, the validated CFD model was employed to simulate the combustion of a gasoline-ethanol blend with 45% (by mole) ethanol (E45) and a gasoline-butanol blend with 45% (by mole) n-butanol (B45) under the same operating conditions to study the effects of fuel composition and SOI timing on combustion phasing and soot emissions. The sooting propensity followed the trend: B45 > E20 > E45 at all SOI timings. Overall, it was observed that the autoignition propensity was primarily related to fuel chemistry. On the other hand, sooting propensity showed strong coupling with both fuel chemistry and physical properties, with greater impact of fuel physical properties at advanced SOI timings.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2026

Pressurized Gas-Driven Elemental Redistribution Enables Ultrastable PtNi Catalysts for Heavy-Duty Vehicles

Gas-driven element redistribution, characterized by the preferential enrichment of one element at the surface relative to the bulk, is frequently observed in multicomponent alloys. Using L1 0 -ordered PtNi as a model system, we reveal that gas pressure plays a critical role in governing adsorption-driven surface composition during annealing in reducing gases: low pressure favors Pt surface segregation, while high pressure facilitates Ni surface enrichment. In this study, we developed a high-pressure nitriding (HPN) strategy that modulates the surface structure and composition of PtNi catalysts. The resulting HPN-PtNi exhibits enhanced performance and durability in membrane electrode assemblies for heavy-duty fuel cell applications, maintaining a high current density of 1.19 A cm −2 at 0.7 V after 90,000 voltage cycles. Through a combination of experimental and theoretical analyses, we reveal that the HPN process forms additional stabilizing Ni−N bonds and induces elemental redistribution with Ni surface enrichment and a Ni-deficient Pt subsurface. These modifications alter the atomic coordination environment of the ordered PtNi phase. This work presents a generalizable strategy to design robust and high-performing Pt-based catalysts by controlling gas-pressure-driven elemental redistribution and dopant incorporation.

30 DIRECT ENERGY CONVERSION↗