Mesoscale model and X-ray computed micro-tomographic imaging of damage progression in ultra-high-performance concrete
Not Available
36 MATERIALS SCIENCE↗
SEARCH · Engineering Papers
Results for “microstructural analysis”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Texture and precipitation behavior of friction stir welded Inconel 825 alloy
The microstructure, texture pattern, and precipitation behavior of friction stir butt welded Inconel 825 alloy are highlighted here. The microstructure of bright regions and black-banded regions in the stir zone (SZ) is characterized by SEM, EBSD, and TEM with EDS. EBSD analysis justifies that the SZ exhibits a dynamic recrystallized structure. Grain boundary mapping corroborates the insignificant difference in the low- and high-angle grain boundaries fraction between the SZ, the thermo-mechanically affected zone, and the base metal. TEM analysis confirms the formation of nano twins and dispersion of nano-size precipitations in the grains, and at the grain boundaries as well. Grain refinement and nano-size precipitation formation in the SZ significantly enhanced both microhardness and tensile strength.
Das, Hrishikesh↗
Grain boundary strain localization in a CdTe solar cell revealed by scanning 3D X-ray diffraction microscopy
Scanning 3DXRD was used to visualize strain localization at grain boundaries with a high spatial resolution of 100 nm.
Shukla, Aditya↗
Microstructural stability and mechanical properties of the as-cast and heat-treated newly developed TiNbCrTa refractory complex concentrated alloy
In this study, a TiNbCrTa refractory complex concentrated alloy (RCCA) was prepared using vacuum arc remelting. The microstructural evolution and mechanical properties of both as-cast and heat-treated RCCA samples were analyzed. Heat treatment (HT) was performed at 800–1200 °C for 1 h in a vacuum-sealed environment. These samples exhibited a formation of Cr 2 Nb and Cr 2 Ti Laves phases. A variation in elemental distribution was observed, with interdendritic (ID) regions showing higher fractions of Ti and Cr, while the dendritic regions had a greater concentration of Ta and Nb. Micro-segregation at the IDs was confirmed through energy dispersive x-ray spectroscopy mapping, which inferred the formation of Cr- and Ti-rich phases during HT at 800–1200 °C. High-temperature HT at 1200 °C for 1 h led to the evolution of the hcp omega phase. Prolonged HT at 1200 °C for 96 h resulted in the evolution of a Cr-rich Laves phase (Cr 2 Ta), which was homogeneously distributed within the microstructure, indicating an unstable microstructure. Furthermore, despite prolonged HT, a variation in the elemental distribution persisted due to the presence of dendritic and ID regions. Electron backscattered diffraction analysis revealed the presence of bcc and hcp phases in the dendritic and ID regions, respectively, of the as-cast and HTed samples. The as-cast samples demonstrated a high compressive strength of approximately 2 GPa. Micro-hardness values increased with the HT temperature up to 1000 °C. Further increases under HT conditions did not significantly reduce the microhardness value, whereas prolonged HT at 1200 °C led to an increase in the microhardness value. Overall, the newly developed TiNbCrTa RCCA exhibited high-strength behavior even after the phase transformation.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Fossil Corals With Various Degrees of Preservation Can Retain Information About Biomineralization-Related Organic Material
Scleractinian corals typically form a robust calcium carbonate skeleton beneath their living tissue. This skeleton, through its trace element composition and isotope ratios, may record environmental conditions of water surrounding the coral animal. While bulk unrecrystallized aragonite coral skeletons can be used to reconstruct past ocean conditions, corals that have undergone significant diagenesis have altered geochemical signatures and are typically assumed to retain insufficient meaningful information for bulk or macrostructural analysis. However, partially recrystallized skeletons may retain organic molecular components of the skeletal organic matrix (SOM), which is secreted by the animal and directs aspects of the biomineralization process. Some SOM proteins can be retained in fossil corals and can potentially provide past oceanographic, ecological, and indirect genetic information. Here, we describe a dataset of scleractinian coral skeletons, aged from modern to Cretaceous plus a Carboniferous rugosan, characterized for their crystallography, trace element composition, and amino acid compositions. We show that some specimens that are partially recrystallized to calcite yield potentially useful biochemical information whereas complete recrystalization or silicification leads to significant alteration or loss of the SOM fraction. Our analysis is informative to biochemical-paleoceanographers as it suggests that previously discounted partially recrystallized coral skeletons may indeed still be useful at the microstructural level.
58 GEOSCIENCES↗
Evolution of carbide precipitates in Haynes® 282 superalloy processed by wire arc additive manufacturing
Precipitation hardening regulated with heat treatments is a critical technique for tuning the mechanical properties of Ni-based superalloys fabricated with additive manufacturing, where mechanical deformation is no longer viable for microstructural refinement. As one of the key precipitates, carbides prevail in the additively manufactured alloys, whose precipitation kinetics remain largely vague. This work studies the influence of heat treatments on the evolution of MC- and M 23 C 6 -type carbides within a Haynes® 282 superalloy prepared by wire arc additive manufacturing (WAAM). SEM-EDS analysis was performed to identify the evolution pathways of the carbides, and TEM and XRD characterizations were carried out to track the crystallographic features. The MC-type carbides are originally present in the as-printed alloy, which distribute uniformly across the whole material and remain largely unchanged in size during the heat treatments. By contrast, the incipiently non-existent M 23 C 6 -type carbides precipitate during an aging treatment at 1010 °C, which majorly extend along the grain boundaries as kinetically feasible sites. Further experimental and computational analysis confirms the enhancing effect of the M 23 C 6 -type carbides on the Vickers hardness. For the first time, this work revealed the evolution pathways of carbides within a Haynes® 282 superalloy prepared by WAAM, providing critical information for tunning the microstructure and mechanical properties. Finally, the carbide evolution kinetics established in this work can be potentially extended to other alloys prepared with WAAM, providing critical information to prevent mechanical failures associated with carbide coarsening.
36 MATERIALS SCIENCE↗
Influence of rolling reduction and annealing on recrystallization and grain structure in Ta-2.5W alloys
The microstructural evolution of wrought Tantalum - 2.5 wt% Tungsten (Ta-2.5W) alloys during thermomechanical processing is critical for optimizing their mechanical reliability in demanding applications such as aerospace, chemical processing, and nuclear technology. Despite the widespread use of Ta-W alloys, a comprehensive understanding of how rolling reduction, annealing temperature, and elemental inhomogeneity interact to determine recrystallization behavior and grain refinement remains incomplete. Here, in this study, we systematically investigate the effects of cold rolling and subsequent annealing on the microstructure of Ta-2.5W, with particular attention to grain orientation, stored energy, and elemental banding. Our results demonstrate that higher rolling reduction rates lower the onset and completion temperatures for recrystallization, resulting in finer and more homogeneous grain structures. Electron backscatter diffraction (EBSD) analysis reveals that grains with a 〈111〉 parallel to the plate normal possess higher stored energy and nucleate recrystallization more readily than grains with a 〈001〉 parallel to the plate normal. Elemental mapping shows that tungsten inhomogeneity leads to localized bands of accelerated recrystallization and hardness variation. These findings provide new insights into the mechanisms of microstructure refinement in Ta-2.5W alloys, offering guidance for tailoring processing routes to achieve superior performance in demanding engineering environments.
Annealing↗
Nanoscale Phase Separation and Large Refrigerant Capacity in Magnetocaloric Material LaFe 11.5 Si 1.5
Here, ferromagnetic transitions, the magnetocaloric effect, and the atomic-scale microstructure in an annealed bulk material of LaFe 11.5 Si 1.5 were investigated using magnetic measurements, Mössbauer spectroscopy, high-resolution X-ray diffraction analysis, and high-resolution transmission electron microscopy. The results provide evidence of the coexistence of two ferromagnetic phases with different Curie temperatures. The phase with a Curie temperature of 216 K corresponds to a Si-rich phase of a NaZn 13 -type structure with a small lattice volume, whereas the phase with a Curie temperature of 185 K corresponds to a Si-poor phase of a NaZn 13 -type structure with a large lattice volume. This phase coexistence is observed on a nanometer scale and it can account for inverse thermal hysteresis of the ferromagnetic transition in the Si-rich phase during warming. Furthermore, the phase coexistence helps the bulk material achieve a refrigeration capacity of 170 J kg -1 due to a combination of the magnetocaloric effect in each phase. It is determined that the magnetocaloric effect in the Si-rich and the Si-poor phase brings about a maximum of the total entropy change of -3.55 and -6.80 and J kg -1 K -1 at respective Curie temperatures, respectively. Fundamentally, the phase coexistence indicates coloring of Si atoms in the lattice of a NaZn 13 -type structure and can be attributed to nanoscale phase separation of a disordered precursor during annealing of the bulk material. The nanoscale phase separation may occur in other magnetocaloric materials, thus allowing for improvement of their refrigeration capacity.
36 MATERIALS SCIENCE↗
Quantifying the Impacts of Grain-scale Heterogeneity on Mechanical Response
Driven by the exceedingly high computational demands of simulating mechanical response in complex engineered systems with finely resolved finite element models, there is a critical need to optimally reduce the fidelity of such simulations. The minimum required fidelity is constrained by error tolerances on the simulation results, but error bounds are often impossible to obtain a priori. One such source of error is the variability of material properties within a body due to spatially non-uniform processing conditions and inherent stochasticity in material microstructure. This study seeks to quantify the effects of microstructural heterogeneity on component- and system-scale performance to aid in the choice of an appropriate material model and spatial resolution for finite element analysis.
36 MATERIALS SCIENCE↗
Computer vision models and advanced TEM imaging for microstructures of irradiated AM316 stainless steels
Advancements were made in automating microscopy-based material characterization, particularly in studying irradiation effects on additively manufactured (AM) materials using machine learning (ML) and computer vision (CV). These automation efforts address the challenges of analyzing complex microstructures, accelerating the detection of irradiation-induced defects. Two CV models were developed at Argonne National Laboratory (ANL) to enhance transmission electron microscopy (TEM) analysis of irradiated AM 316 stainless steel. The first model focused on the detection of irradiation-induced dislocation loops, which contribute to material hardening and embrittlement. These loops, categorized as faulted or perfect, were automatically detected and classified using a Mask R-CNN model trained on TEM images from both in-situ and ex-situ ion irradiation experiments. The model achieved high accuracy, with precision, recall, and F1 scores of 0.839, 0.734, and 0.776, respectively, demonstrating its effectiveness in analyzing dislocation loops in irradiated AM materials. The second CV model was developed to analyze the size and wall thickness of dislocation cells in laser powder bed fusion (LPBF) 316 stainless steel. Using a U-Net++ architecture with EfficientNet as the encoder, the model was trained on TEM images to segment and measure cell size and wall thickness.
36 MATERIALS SCIENCE↗
Regional Subsidence Analysis Through a Multi-Scale Modeling Framework Based on Breakage Mechanics
Although poroelastic models are often used to explain the delay between subsurface fluid depletion and ground subsidence, inelastic compaction involving permanent changes of rock microstructure may exacerbate hydro-mechanical coupling, thus influencing the interpretation of measurements and long-term forecasts. Here, a multi-scale modeling approach is discussed, which accounts for the inherent connection between rock microstructure, hydraulic conductivity, and pore compaction. A constitutive model built within the framework of breakage mechanics is proposed to link the hydraulic conductivity of granular rocks with inelastic deformations and changes in grading caused by injection-depletion cycles at stress levels far from yielding. The proposed model has been incorporated into large-scale simulation frameworks, thus enabling the spatiotemporal mapping of regional subsidence through a hybrid, semi-analytical approach. Numerical results based on this strategy show that the model allows isolating near-field and far-field effects into the computation of land subsidence and can generate forecasts for different modeling scenarios (e.g., elastic and inelastic compaction, constant permeability, and concurrent change of compressibility and permeability). In particular, examples of simulations for the case of the Groningen gas field are discussed, showing the model capabilities to use both field measurements and laboratory tests for the generation of reasonable subsidence maps, without expensive computational costs. Results indicate that ignoring coupled inelastic effects has major consequences on the predicted timescale of subsidence. Specifically, while all the model scenarios produced similar long-term ground settlements, those ignoring breakage-dependent permeability changes result in a variation of the temporal window of residual subsidence of the order of several decades.
58 GEOSCIENCES↗
Atomic and microstructural origins of stored energy release in neutron-irradiated silicon carbide
Explore the source record for details and available documents.
99 GENERAL AND MISCELLANEOUS↗
Dynamic Scaling Analysis of Accelerated Irradiation Testing on Additive Manufacturing Materials by Positron Annihilation
The timely applications of Additive Manufacturing (AM) materials in nuclear environments require accelerated irradiation tests, mainly ion irradiation to enable rapid prototyping. Low dose ion irradiation would cause sub-nanostructure changes by generation of lattice defects, vacancies, vacancy clusters and voids and void swelling caused by cellular dislocations. Positron Annihilation Lifetime (PAL), a novel technology, sensitive towards sub-nanostructure morphology with high accuracy (about 10-7 vacancy per atom), supported by Transition Electron Microscope (TEM) would be applied to identify the type and total size of the defects. The subsequent PAL measurements and TEM surface studies would be followed by PAL analysis that includes sophisticated trapping model. The PAS results would become an input to dynamic scaling analysis (that predicts radiation effects from low dose studies for high dose effects), which incorporate mean-field theory model. The final effect is an in-depth understanding of the microstructure evolution of AM materials under ion irradiation which can be extrapolated to the studies of neutron irradiation, since ion-irradiation takes less time and do not cause the irradiation hazard. The working hypothesis is that PAL technology, that have excellent sensitivity to low-defect concentration would help to identify ion-induced material damage on the atomic and nano-scale level, which then could be extrapolated to understand the neutron damage better.
accelerated irradiation testing↗
Multiscale design of nonlinear materials using a Eulerian shape optimization scheme
Motivated by recent advances in manufacturing, the design of materials is the focal point of interest in the material research community. One of the critical challenges in this field is finding optimal material microstructure for a desired macroscopic response. This work presents a computational method for the mesoscale-level design of particulate composites for an optimal macroscale-level response. The method relies on a custom shape optimization scheme to find the extrema of a nonlinear cost function subject to a set of constraints. Three key “modules” constitute the method: multiscale modeling, sensitivity analysis, and optimization. Multiscale modeling relies on a classical homogenization method and a nonlinear NURBS-based generalized finite element scheme to efficiently and accurately compute the structural response of particulate composites using a nonconformal discretization. A three-parameter isotropic damage law is used to model microstructure-level failure. An analytical sensitivity method is developed to compute the derivatives of the cost/constraint functions with respect to the design variables that control the microstructure's geometry. The derivation uncovers subtle but essential new terms contributing to the sensitivity of finite element shape functions and their spatial derivatives. Several structural problems are solved to demonstrate the applicability, performance, and accuracy of the method for the design of particulate composites with a desired macroscopic nonlinear stress-strain response.
42 ENGINEERING↗
Towards data-driven constitutive modelling for granular materials via micromechanics-informed deep learning
The analytical description of path-dependent elastic-plastic responses of a granular system is highly complicated because of continuously evolving microstructures and strain localisation within the system undergoing deformation. This study offers an alternative to the current analytical paradigm by developing micromechanics-informed machine-learning based constitutive modelling approaches for granular materials. A set of critical variables associated with the constitutive behaviour of granular materials are identified through an incremental stress-strain relationship analysis. Depending on the strategy to exploit the priori micromechanical knowledge, three different training strategies are explored. The first model uses only the measurable external variables to make stress predictions; the second model utilises a directed graph to link all the external strain sequences and internal microstructural evolution variables into a single prediction model comprised of a series of sub-mappings, and the third model explicitly integrates the physically important non-temporal properties with external strain paths into training through an enhanced Gated Recurrent Unit (GRU). These three models show satisfactory agreement with unseen test specimens based on multi-directional loading cases. The basic features and potential applications of each model are explained. Lastly, the key factors for constitutive training and limitations of the current work are also discussed in detail.
36 MATERIALS SCIENCE↗
Tuning Microstructure of Mesophase Pitch Carbon Fiber by Altering the Carbonization Ramp Rate
The microstructure of mesophase pitch carbon fibers (CFs) are tuned by varying ramp rates from 1 to 50 °C min –1 up to 1000 °C to study the effect of ramp rate on CFs’ microstructure, thermal and mechanical properties with the goal of offsetting the cost by decreasing cycle time. The ramp rates represent carbonization times ranging from 16.4 to 1.17 h, not including cool down. Differential scanning calorimetry, thermogravimetric analysis, and derivative thermogravimetry are used to investigate the impact ramp rate has on the thermal properties of mesophase pitch. It is found that lower ramp rates are endothermic in nature with a lower temperature onset and maximum weight loss. Higher ramp rates possess an exothermic nature with higher temperatures resulting in maximal weight loss over a smaller range of temperatures. Mechanical testing shows varying CF strengths and moduli dependent on ramp rate and an optimized process is developed to produce the strongest CF. Furthermore, microstructural characterization revealed that faster ramp rates lead to smaller interplanar spacings and larger crystallites but possessed greater disorder.
36 MATERIALS SCIENCE↗
Corrosion Response of Ni-19Cr-5Fe in Molten NaCl-MgCl 2 Salt
Ni-based alloys are strong candidates for use in high-temperature molten salt reactors due to their superior corrosion resistance and mechanical stability compared to stainless steels. In this study, the static corrosion behavior of a Ni-19Cr-5Fe model alloy was systematically evaluated in a purified molten NaCl-MgCl 2 salt at 700°C for 30, 240, and 500 h. Post-exposure analyses were conducted to assess microstructural evolution, corrosion depth, and elemental depletion profiles. Corrosion rates, quantified by chromium depletion depth, followed an inverse power-law trend with increasing exposure time, indicating diffusion-limited kinetics. This trend is attributed to limitations in mass transport in the static salt and to the progressive local depletion of reactive chromium species. Coupled electron backscatter diffraction and energy dispersive X-ray spectroscopy analysis further revealed that the grain boundary character significantly influences corrosion susceptibility: high-angle grain boundaries exhibited pronounced Cr depletion and pitting, while low-angle and Σ3 boundaries remained comparatively resistant. These results offer valuable insight into the role of microstructure in corrosion processes and reinforce the importance of time-dependent material evaluation in molten salt environments relevant to advanced reactor designs.
11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Microstructure Experiments-Enabled MARMOT Simulations of SiC/SiC-based Accident Tolerant Nuclear Fuel System
We have undertaken an experimental-computational project that addresses a few key technology gaps associated with the use of SiC/SiC composites for light water reactor fuel cladding. Two principal endeavors in this project are to assess the irradiation-induced microstructural changes and swelling in SiC/SiC composites, and to characterize and model the porous oxide surface layer (when exposed to steam) along SiC recession that is detrimental to the clad integrity under accident conditions. The project tasks are: (i) ion irradiation and characterization (University of Tennessee, Knoxville), (ii) mechanical tests and analysis (University of South Carolina), (iii) steam exposure tests (Oak Ridge National Laboratory), (iv) electron microscopy and spectroscopic characterization (NC State University), (v) x-ray microscopy and reconstruction (University of South Carolina and NC State University), (vi) phase field modeling and simulations (NC State University and Idaho National Laboratory). The effects of 10 MeV Au ion irradiation at 350°C on the microstructure evolution in SiC/SiC composites are investigated at doses up to 400 displacements per atom (dpa) at the University of Tennessee, Knoxville. Atomic force microscopy and optical profilometry reveal irradiation induced axial and radial shrinkage of the fibers for doses greater than 10 dpa. Based on detailed electron microscopy characterization, the primary cause of the fiber shrinkage is attributed to irradiation-induced loss of carbon packets. Additionally, the multilayer PyC interface is observed to portray high resistance to irradiation damage. The mechanical response and failure mechanisms of un-irradiated samples is also assessed through loading tests and X-ray imaging at the University of South Carolina. Steam exposure tests are performed at the Oak Ridge National Laboratory in a facility that represents a reactor pressure vessel under a loss-of-coolant-accident scenario. The samples that are analyzed methodically in this report are tested for 32/31 hours at 1200°C with a velocity of 0.25 cm/s for the pressures: 0.1 MPa, 0.45 MPa, 0.92 MPa and 1.38 MPa. Scanning/transmission electron microscopy analysis conducted at the NC State University (NCSU) shows that the oxide layer thickness increases with the steam pressure. While the oxide layer is crystalline (α- cristobalite) for the pressures 0.45 MPa, 0.92 MPa and 1.38 MPa, the layer is amorphous at 0.1 MPa. Results from Raman spectroscopy have also confirmed the formation of α-cristobalite phase of SiO₂. The abrupt increase in the integrated Raman intensity ratio between steam pressures 0.1 and 0.45 MPa suggests the onset of accelerated crystallization. Non-destructive three dimensional X-ray microscopy/tomography (XCT) and computational image processing techniques are employed by the University of South Carolina to probe the porous oxidation features on SiC samples at varying pressures. Interestingly, most pores are observed to be located away from the surface as well as the oxide-SiC interface. The average oxide layer thickness assessed from the XCT analysis is seen to be in excellent agreement with the values determined through scanning electron microscopy analysis for the highest pressures where the oxide layer is relatively more uniform. A phase-field model developed by the NC State University and Idaho National Laboratory for simulating oxidation of SiC by steam captures the paralinear kinetics of SiC oxidation with a high degree of fidelity. Results from quasi-one-dimensional and two dimensional simulations show that the pores with oxidizing species lead to a higher volatilization rate. These simulations indicate that the enhanced apparent volatilization rates at higher pressures observed in experiments can be rationalized by the increased volatilization from the pores. The project team has also successfully developed the capability to import images from experiments for realistic evolution of the oxidizing microstructure.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗