Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “methyl esters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Air-stable solution-processed n-channel organic thin film transistors with polymer-enhanced morphology

N,N′-1H,1H-perfluorobutyl dicyanoperylenecarboxydiimide (PDIF-CN{sub 2}) is an n-type semiconductor exhibiting high electron mobility and excellent air stability. However, the reported electron mobility based on spin-coated PDIF-CN{sub 2} film is much lower than the value of PDIF-CN{sub 2} single crystals made from vapor phase deposition, indicating significant room for mobility enhancement. In this study, various insulating polymers, including poly(vinyl alcohol), poly(methyl methacrylate) (PMMA), and poly(alpha-methylstyrene) (PαMS), are pre-coated on silicon substrate aiming to enhance the morphology of the PDIF-CN{sub 2} thin film, thereby improving the charge transport and air stability. Atomic force microscopy images reveal that with the pre-deposition of PαMS or PMMA polymers, the morphology of the PDIF-CN{sub 2} polycrystalline films is optimized in semiconducting crystal connectivity, domain size, and surface roughness, which leads to significant improvement of organic thin-film transistor (OTFT) performance. Particularly, an electron mobility of up to 0.55 cm{sup 2}/V s has been achieved from OTFTs based on the PDIF-CN{sub 2} film with the pre-deposition of PαMS polymer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Passively Q-switched erbium-doped fiber laser using quantum dots CdSe embedded in polymer film as saturable absorber

We demonstrate a passively Q-switched erbium doped fiber laser (EDFL) based on quantum dots (QD) CdSe as a saturable absorber (SA). The synthesized CdSe powder was embedded into a poly(methyl methacrylate) (PMMA) using emulsion polymerization process. The film is sandwiched between two fiber connector via an adapter to form a fiber-compatible SA device. By integrating the SA device into the EDFL ring cavity, the stable Q-switched operation is achieved at 1559.35 nm as the pump power is varied within 30–118 mW. The laser has a pump threshold of 20.4 mW. The pulse repetition rate shows an increasing trend from 33.2 to 68.45 kHz, whereas the pulse width exhibits a decreasing trend from 10.04 to 4.30 μs as the pump power is increased from 30 to 118 mW. The highest pulse energy of 11.83 nJ is obtained at a pump power of 118 mW. These results indicate that QD CdSe is a promising SA for Q-switching laser operation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

One-pot fabrication and characterization of graphene/PMMA composite flexible films

Highlights: • Investigated the fabrication and characterization of conducting flexible films based on graphene/PMMA polymer composite. • Graphene/PMMA flexible films were fabricated by one-pot alternate stirring sonication (OPASS) process. • Electrical response of the fabricated flexible films were studied and exhibited an electrical conductivity of 44.92 S/m and 0.10 S/m with 50 wt% and 10 wt% concentrations, respectively. • Reinforcing polymers with graphite platelets will amend their surface toughness, modulus and barrier properties, suitable for commercial applications. - Abstract: The present work investigates fabrication and characterization of graphene/ poly (methyl methacrylate) (PMMA) composite flexible films. Graphene/PMMA flexible films were fabricated by one-pot alternate stirring sonication (OPASS) process. The method relies on the alternate high speed stirring and ultrasonication of graphite and its blending with PMMA without any sufactant assistance. A comparative study of the nanocomposite solution was carried out with the composite solution prepared by conventional (CL) method. The transformation of micro-sized graphite particles to nano-sized layers of graphite or few layer graphene was characterized by various analytical techniques. The electrical response of the fabricated flexible films were studied and exhibited an electrical conductivity of 44.92 S/m and 0.10 S/m with 50 wt% and 10 wt% concentrations, respectively. Thus, the fabricated flexible films could have excellent surface toughness, modulus and barrier properties, which make them a suitable candidate for commercial flexible electronic and wearable sensor applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Vinyl monomers-induced synthesis of polyvinyl alcohol-stabilized selenium nanoparticles

A simple wet chemical method has been developed to synthesize selenium nanoparticles (size 100-200 nm), by reaction of sodium selenosulphate precursor with different vinyl monomers, such as acrylamide, N,N'-dimethylene bis acrylamide, methyl methacrylate, sodium acrylate, etc., in aqueous medium, under ambient conditions. Polyvinyl alcohol has been used to stabilize the selenium nanoparticles. Average size of the synthesized selenium nanoparticles can be controlled by adjusting concentration of both the precursors and the stabilizer. Rate of the reaction as well as size of the resultant selenium nanoparticles have been correlated with the functional groups of the different monomers. UV-vis optical absorption spectroscopy, X-ray diffraction, energy dispersive X-rays, differential scanning calorimetry, atomic force microscopy, scanning electron microscopy and transmission electron microscopy techniques have been employed to characterize the synthesized selenium nanoparticles. Gas chromatographic analysis of the reaction mixture established the non-catalytic role of the vinyl monomers, which were found to be consumed during the course of the reaction.

36 MATERIALS SCIENCE↗

Phase separation during bulk polymerization of methyl methacrylate

We report on the phase separation of methyl methacrylate (MMA) and poly(methyl methacrylate) (PMMA) during bulk free-radical polymerization. The phase separation is induced when the reaction is initiated at room temperature by the redox reaction of benzoyl peroxide in the presence of an amine. During the reaction, the ratio of MMA and PMMA changes continuously. Separation into MMA-rich and PMMA-rich phases coincides with the onset of the Trommsdorff effect. At room temperature, the interface between the two phases remains, even after drying the remaining monomer. When the sample is annealed above the glass transition temperature Tg, the interface disappears. Due to the frozen dynamics of the polymer chains, subsequent cooling below Tg does not result in further phase separation. This result provides evidence for the existence of rich, thermodynamically stable states, which are typically suppressed due to the frozen dynamics of polymers at temperatures below the Tg, after thermal processing above the Tg.

36 MATERIALS SCIENCE↗

Studies on the Properties of Plasticizer and Lithium Salt on PMMA-based Solid Polymer Electrolytes

The effects of plasticizer and lithium salt on PMMA-based solid polymer electrolyte have been investigated. In current project, three system samples consisted of pure poly(methyl methacrylate (PMMA) system, plasticized poly(methyl methacrylate)(PMMA-EC) system and the LiCF{sub 3}SO{sub 3} salted-poly(methyl methacrylate) containing a fixed amount of plasticizer ([PMMA-EC]-LiCF{sub 3}SO{sub 3}) system have been prepared using solution casting technique. The conductivities of the films from each system are characterized by impedance spectroscopy and infrared spectrum. With the addition of plasticizer, results show improvement on the ionic conductivity value where the value of 6.25x10{sup -10} Scm{sup -1} is obtained. This may be due to the nature of plasticizer that softens the polymer and hence enhanced the ionic transportation across the polymer. The room temperature conductivity for the highest conducting sample in the ([PMMA-EC]-LiCF{sub 3}SO{sub 3}) system is 1.36x10{sup -5} Scm{sup -1}. Fourier Transform Infrared Spectroscopy (FTIR) indicates complexation between the polymer and the plasticizer and the polymer, the plasticizer and the salts, and the result of XRD further supports the observation.

36 MATERIALS SCIENCE↗

Polymer/metal oxide hybrid dielectrics for low voltage field-effect transistors with solution-processed, high-mobility semiconductors

Transistors for future flexible organic light-emitting diode (OLED) display backplanes should operate at low voltages and be able to sustain high currents over long times without degradation. Hence, high capacitance dielectrics with low surface trap densities are required that are compatible with solution-processable high-mobility semiconductors. Here, we combine poly(methyl methacrylate) (PMMA) and atomic layer deposition hafnium oxide (HfO{sub x}) into a bilayer hybrid dielectric for field-effect transistors with a donor-acceptor polymer (DPPT-TT) or single-walled carbon nanotubes (SWNTs) as the semiconductor and demonstrate substantially improved device performances for both. The ultra-thin PMMA layer ensures a low density of trap states at the semiconductor-dielectric interface while the metal oxide layer provides high capacitance, low gate leakage and superior barrier properties. Transistors with these thin (≤70 nm), high capacitance (100–300 nF/cm{sup 2}) hybrid dielectrics enable low operating voltages (<5 V), balanced charge carrier mobilities and low threshold voltages. Moreover, the hybrid layers substantially improve the bias stress stability of the transistors compared to those with pure PMMA and HfO{sub x} dielectrics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Temperature dependent dielectric properties and ion transportation in solid polymer electrolyte for lithium ion batteries

Solid polymer electrolyte (SPE) film consisted of poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) blend matrix with lithium tetrafluroborate (LiBF{sub 4}) as dopant ionic salt and poly(ethylene glycol) (PEG) as plasticizer has been prepared by solution casting method followed by melt pressing. Dielectric properties and ionic conductivity of the SPE film at different temperatures have been determined by dielectric relaxation spectroscopy. It has been observed that the dc ionic conductivity of the SPE film increases with increase of temperature and also the decrease of relaxation time. The temperature dependent relaxation time and ionic conductivity values of the electrolyte are governed by the Arrhenius relation. Correlation observed between dc conductivity and relaxation time confirms that ion transportation occurs with polymer chain segmental dynamics through hopping mechanism. The room temperature ionic conductivity is found to be 4 × 10{sup −6} S cm{sup −1} which suggests the suitability of the SPE film for rechargeable lithium batteries.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Preparation of three-dimensionally ordered macroporous perovskite-type lanthanum-iron-oxide LaFeO{sub 3} with tunable pore diameters: High porosity and photonic property

Three-dimensionally ordered macroporous (3DOM) lanthanum-iron-oxide (LaFeO{sub 3}) with different pore diameters was prepared using a colloidal crystal of polymer spheres with different diameters as templates. Ethylene glycol-methanol mixed solution of metal nitrates was infiltrated into the void of the colloidal crystal template of a monodispersed poly(methyl methacrylate) (PMMA) sphere. Heating of this PMMA-metal salt-ethylene glycol composite produced the desired well-ordered 3DOM LaFeO{sub 3} with a high pore fraction, which was confirmed by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), mercury (Hg) porosimetry, and ultraviolet-visible (UV-vis) diffuse reflectance spectra. 3DOM LaFeO{sub 3} with pore diameters of 281 and 321 nm shows opalescent colors because of photonic stop band properties. Catalytic activity of the 3DOM LaFeO{sub 3} for combustion of carbon particles was enhanced by a potassium cation, which was involved from K{sub 2}S{sub 2}O{sub 8} used as a polymerization initiator. - Graphical abstract: Well-ordered three-dimensionally ordered macroporous LaFeO{sub 3} materials with pore sizes ranging from 127 to 321 nm were obtained in a high pore fraction.

36 MATERIALS SCIENCE↗

Inelastic scattering of electron and light ion beams in organic polymers

We have calculated the inelastic mean free path, stopping power, and energy-loss straggling of swift electron, proton, and {alpha}-particle beams in a broad incident energy range in four organic polymers: poly(methyl methacrylate) (PMMA), Kapton, polyacetylene (PA), and poly(2-vinylpyridine) (P2VP). These calculations have been done through a suitable description of their optical properties and its extension into the whole momentum and energy transfer excitation spectrum. For electrons, we take into account the exchange effect between the projectile and the target electrons, while the charge-state fractions have been considered for ions. Our results are compared with other models and with the available experimental data. An excellent agreement with experimental data is obtained in the case of proton and {alpha}-particle beams in Kapton and a reasonably good agreement has been achieved for electron beams in PMMA, Kapton, and PA. We have parameterized by means of simple analytical expressions our results for electron beams interacting with these four polymers, which can be easily implemented in Monte Carlo calculations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nucleation and growth of ZnO on PMMA by low-temperature atomic layer deposition

ZnO films were grown by atomic layer deposition at 35 °C on poly(methyl methacrylate) substrates using diethylzinc and water precursors. The film growth, morphology, and crystallinity were studied using Rutherford backscattering spectrometry, time-of-flight elastic recoil detection analysis, atomic force microscopy, scanning electron microscopy, and x-ray diffraction. The uniform film growth was reached after several hundreds of deposition cycles, preceded by the precursor penetration into the porous bulk and island-type growth. After the full surface coverage, the ZnO films were stoichiometric, and consisted of large grains (diameter 30 nm) with a film surface roughness up to 6 nm (RMS). The introduction of Al{sub 2}O{sub 3} seed layer enhanced the initial ZnO growth substantially and changed the surface morphology as well as the crystallinity of the deposited ZnO films. Furthermore, the water contact angles of the ZnO films were measured, and upon ultraviolet illumination, the ZnO films on all the substrates became hydrophilic, independent of the film crystallinity.

36 MATERIALS SCIENCE↗

Composite polymer electrolytes based on MG49 and carboxymethyl cellulose from kenaf

The development of 49% poly(methyl methacrylate)-grafted natural rubber (MG49) and carboxymethyl cellulose as a composite polymer electrolyte film incorporating LiCF{sub 3}SO{sub 3} were explored. Carboxymethyl cellulose was synthesized from kenaf bast fibres via carboxymethylation process by alkali catalyzed reaction of cellulose with sodium chloroacetate. Reflection fourier transform infrared (ATR-FTIR) spectroscopy showed the presence of carboxyl peak after modification of cellulose with sodium chloroacetate. X-ray diffraction (XRD) analysis revealed that the crystallinity of cellulose was decrease after synthesis. High performance composite polymer electrolytes were prepared with various composition of carboxymethyl cellulose (2–10 wt%) via solution-casting method. The conductivity was increased with carboxymethyl cellulose loading. The highest conductivity value achieved was 3.3 × 10{sup −7} Scm{sup −1} upon addition of 6% wt carboxymethyl cellulose. 6% wt carboxymethyl cellulose composition showed the highest tensile strength value of 7.9 MPa and 273 MPa of modulus value which demonstrated high mechanical performance with accepatable level of ionic conductivity.

36 MATERIALS SCIENCE↗

Exploring mechanisms of a tropospheric archetype: CH{sub 3}O{sub 2} + NO

Methylperoxy radical (CH{sub 3}O{sub 2}) and nitric oxide (NO) contribute to the propagation of photochemical smog in the troposphere via the production of methoxy radical (CH{sub 3}O) and nitrogen dioxide (NO{sub 2}). This reaction system also furnishes trace quantities of methyl nitrate (CH{sub 3}ONO{sub 2}), a sink for reactive NO{sub x} species. Here, the CH{sub 3}O{sub 2} + NO reaction is examined with highly reliable coupled-cluster methods. Specifically, equilibrium geometries for the reactants, products, intermediates, and transition states of the ground-state potential energy surface are characterized. Relative reaction enthalpies at 0 K (ΔH{sub 0K}) are reported; these values are comprised of electronic energies extrapolated to the complete basis set limit of CCSDT(Q) and zero-point vibrational energies computed at CCSD(T)/cc-pVTZ. A two-part mechanism involving CH{sub 3}O and NO{sub 2} production followed by radical recombination to CH{sub 3}ONO{sub 2} is determined to be the primary channel for formation of CH{sub 3}ONO{sub 2} under tropospheric conditions. Constrained optimizations of the reaction paths at CCSD(T)/cc-pVTZ suggest that the homolytic bond dissociations involved in this reaction path are barrierless.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Size effect of added LaB{sub 6} particles on optical properties of LaB{sub 6}/Polymer composites

Modified LaB{sub 6} particles with sizes ranging from 50 nm to 400 nm were added into polymethyl methacrylate (PMMA) matrix in order to investigate the effect of added LaB{sub 6} particles on optical properties of LaB{sub 6}/PMMA composites. Method of in-situ polymerization was applied to prepare PMMA from raw material-methyl methacrylate (MMA), a process during which LaB{sub 6} particles were dispersed in MMA. Ultraviolet-visible-near infrared (UV-vis-NIR) absorption spectrum was used to study optical properties of the as-prepared materials. The difference in particle size could apparently affect the composites' absorption of visible light around wavelength of 600 nm. Added LaB{sub 6} particles with size of about 70 nm resulted in the best optical properties among these groups of composites. - Graphical abstract: 70 nm LaB{sub 6} particles resulted in the best performance on absorption of VIS and NIR, which could not be apparently achieved by LaB{sub 6} particles beyond nano-scale. Highlights: Black-Right-Pointing-Pointer LaB{sub 6}/PMMA composites were prepared using the method of in-situ polymerization. Black-Right-Pointing-Pointer LaB{sub 6} particles added in MMA prolonged the time needed for its pre-polymerization. Black-Right-Pointing-Pointer Nanosized LaB{sub 6} particles could obviously absorb much NIR but little VIS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Porous Microcapsule-Based Regenerating Superhydrophobic Coating on 304L SS and Its Corrosion Properties

We report fabrication of a regenerating superhydrophobic coating on 304L stainless steels, with superior corrosion resistance, using porous microcapsules made of calcium hydroxide as a core and a polymeric shell consisting of ethyl cellulose and poly methyl methacrylate. The synthesized microcapsules are characterized using optical, atomic force and scanning electron microscopic techniques, x-ray diffraction, Fourier transform infrared spectroscopy and immersion tests. The diameter of porous and permeable microcapsules ranges from 2 to 20 μm. On immersion of the coated surface in sodium stearate solution, the calcium hydroxide from the core diffuses through the pores of microcapsules and forms nanocrystalline hydrophobic calcium stearate needles pointing outward that repel water molecules. The maximum water contact angle obtained was 155.7° ± 2.05°. The micro-nanoscale roughness of the surface was evident from the AFM measurement. The cross-hatch tape adhesion test confirmed the strong adherence of the superhydrophobic coating. On damage of the superhydrophobic coating, the regeneration is achieved by immersing it in sodium stearate solution for 6 h where a 10° increase in contact angle is observed. Electrochemical studies in 0.1 M NaCl showed significant decrease in the passive current density and a delayed pitting, confirming better corrosion resistance of the coating in chloride environment.

36 MATERIALS SCIENCE↗

Adsorption and electron-induced polymerization of methyl methacrylate on Ru(1010)

The adsorption and electron irradiation of methyl methacrylate (MMA) on a Ru(1010) surface have been studied using x-ray photoelectron spectroscopy (XPS), temperature programmed desorption (TPD), and low energy ion scattering. TPD analysis indicates that a monolayer of MMA chemisorbs and dissociates on the Ru(1010) surface. The reaction products observed upon heating include H{sub 2}, CO, CO{sub 2}, and a small amount of MMA. Physisorbed multilayers of MMA desorb at temperatures around 170 K. Electron irradiation of physisorbed MMA at 140 K leads to a modification of the MMA film: The XPS spectra show an increase in thermal stability of the film with retention of the MMA structure, and indicate that electron irradiation induces polymerization. An increase in the electron bombardment fluence induces a degradation of the formed polymerized species and leads to the accumulation of carbon on the Ru surface. These results are relevant to the accumulation of carbon on surfaces of Ru films that serve as capping layers on Mo/Si multilayer mirrors used in extreme ultraviolet lithography.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Controlled release of cortisone drugs from block copolymers synthetized by ATRP

Diseases affecting posterior eye segment, like macular edema, infection and neovascularization, may cause visual impairment. Traditional treatments, such as steroidal-drugs intravitreal injections, involve chronic course of therapy usually over a period of years. Moreover, they can require frequent administrations of drug in order to have an adequately disease control. This dramatically reduce patient’s compliance. Efforts have been made to develop implantable devices that offer an alternative therapeutic approach to bypass many challenges of conventional type of therapy. Implantable drug delivery systems (DDS) have been developed to optimize therapeutic properties of drugs and ensure their slow release in the specific site. Polymeric materials can play an essential role in modulating drug delivery and their use in such field has become indispensable. During last decades, acrylic polymers have obtained growing interest. Biocompatibility and chemical properties make them extremely versatile, allowing their use in many field such as biomedical. In particular, block methacrylate copolymer with a balance of hydrophilic and hydrophobic properties can be suitable for prolonged DDS in biomedical devices. In this work, we focused on the realization of a system for controlled and long term release of betamethasone 17,21-dipropionate (BDP), a cortisone drug, from methacrylic block copolymers, to be tested in the treatment of the posterior eye’s diseases. Different series of methyl methacrylate/hydroxyethyl methacrylate (MMA/HEMA) block and random copolymers, with different monomer compositions (10–60% HEMA), were synthetized by Atom Transfer Radical Polymerization (ATRP) to find the best hydrophilic/hydrophobic ratio, able to ensure optimal kinetic release. Copolymer samples were characterized by NMR spectroscopy ({sup 1}H-NMR, {sup 13}C-NMR, CosY), SEC, TGA and DSC. Monitoring of drug release from films loaded with BDP was carried out by HPLC analysis. Evaluation of different kinetic models allowed to deduce that release of BDP is controlled over time from PMMA-b-PHEMA 53/47. In particular, PMMA-b-PHEMA 53/47 showed the best release profile to achieve the therapeutic reference dose of 3 µg/die, employed in treatment of posterior eye disease, up to four months. Accordingly, PMMA-b-PHEMA 53/47 has been tested to prepare ocular inserts. Ocular inserts with different shape and the same area of polymer films have been obtained using silicon moulds made by a 3D printer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Preparation and formation mechanism of three-dimensionally ordered macroporous (3DOM) MgO, MgSO{sub 4}, CaCO{sub 3}, and SrCO{sub 3}, and photonic stop band properties of 3DOM CaCO{sub 3}

Three-dimensionally ordered macroporous (3DOM) magnesium (Mg) oxide (MgO), MgSO{sub 4}, calcium (Ca) carbonate (CaCO{sub 3}), and strontium (Sr) carbonate (SrCO{sub 3}) were prepared using a colloidal crystal of polymer spheres as a template. Ethanol or ethanol-water solution of metal salts (acetate or nitrate) and citric acid was infiltrated into the void of the colloidal crystal template of a monodispersed poly(methyl methacrylate) (PMMA) sphere. Heating of this PMMA-metal salt-citric acid composite produced the desired well-ordered 3DOM materials with a high pore fraction, which was confirmed by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and ultraviolet-visible (UV-vis) diffuse reflectance spectra. The presence of citric acid is crucial for production of the 3DOM structures. Reaction of citric acid with metal salt produces metal citrate solid in the void of PMMA spheres, which is necessary to maintain the 3DOM structure during the calcination process. 3DOM CaCO{sub 3} shows opalescent colors because of it's photonic stop band properties. - Graphical abstract: Well-ordered 3-dimensionally ordered macroporous MgO, MgSO{sub 4}, CaCO{sub 3}, and SrCO{sub 3} materials were obtained in a high pore fraction. Highlights: > An easy preparation method of 3D ordered macroporous (3DOM) MgO, MgSO{sub 4}, CaCO{sub 3}, and SrCO{sub 3} materials. > Their structural characterization. > Their formation mechanism. > Photonic properties of 3DOM CaCO{sub 3}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗