Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “laser processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Validation of Manufacturing Process Designs for Stamped Microchannel Recuperators

Microchannel recuperators can achieve high-efficiency power cycles and chemical reactions by recovering waste heat from hot turbine exhaust and chemical reaction streams. However, the industrial application of microchannel recuperators are restricted by the high cost of patterning and bonding. The objective of this study was thus to investigate new methods for producing microchannel recuperators for emerging markets. Based on greenfield cost estimates, process designs based on stamping, laser welding and vacuum brazing of 316L stainless steel laminae were found to be more economical than conventional photochemical machining and diffusion bonding. Subsequently, validation experiments were conducted to produce stamped microchannel components using cost model parameters. At a mass flow rate of 0.99 g/s, the test article made with laser welding was found to provide higher effectiveness than the test article produced using vacuum brazing. Preliminary investigations showed that residual stresses during laser welding of the laminae led to significant warpage, collapsing channels and making lamina-to-lamina fit up challenging. In contrast, the test article produced by vacuum brazing of stamped laminae showed no clogging and 4.6% and 10.5% channel height standard deviation for the cold and hot channels, respectively. Channel variation in the vacuum brazing sample was determined to be caused by misregistration of laminae during brazing. In future work, efforts are needed to choose cheaper, more ductile brazing foils as well as design a brazing fixture to improve lamina-to-lamina registration.

42 ENGINEERING↗
DOE OSTI2022

Diffraction and thermal effect of a Bessel-Gaussian laser for Ag nanoparticle deposition

Nanoparticles are known to sinter at much lower temperatures than the corresponding bulk or micro size particles. A laser-assisted sintering process is considered in this study to sinter Ag nanoparticles by dispensing Ag paste onto an indium tin oxide-coated Si substrate. The Gaussian beam of a CO 2 laser source is propagated through axicon and biconvex lenses, and the resulting hollow beam is focused on the Ag paste with a hollow parabolic mirror. A Bessel-Gaussian irradiance distribution is obtained at the focal plane of the parabolic mirror due to the interference of the hollow laser cone. The Fresnel diffraction approximation is considered to determine the phasor of the laser and an analytical approach is implemented to calculate the irradiance distribution of the Bessel-Gaussian beam. This irradiance distribution is utilized as a heat source in a heat conduction model and the temperature distribution is analyzed for thin Ag films formed during the laser sintering of Ag nanoparticles. An analytical expression is obtained for the temperature distribution by solving the heat conduction equation using Fourier transform for finite media. The widths of the deposited Ag lines are predicted from the temperature profiles and the model predictions compare well with the experimental results. The isotherms are found to be geometrically noncongruent with convex and concave tips depending on the locally maximum and minimum irradiances of the Bessel-Gaussian beam, respectively. The convex and concave tips, however, appear in the same isotherm for sufficiently high substrate speed relative to the laser beam.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
NASA NTRSDate not supplied

TPSAS-NF1676L-32709-DND

Outline - Process-Structure-Performance Framework - Process-Specific Defects in selective laser melting (SLM) additive manufacturing (AM) process - Idealized Keyhole/Entrapped gas pores - Idealized Lack of Fusion (LoF) pores - Influence of Pore Geometry on Strain Localization - 3D Model of LoF pores - Partial validation of the 3D LoF 2 model

Saikumar R Yeratapally↗
DOE OSTI2020

Interference effects in the high-order harmonic amplification process in the active medium of a plasma-based X-ray laser modulated by an optical field

We study the process of propagation of high harmonics of optical radiation in an active medium of a plasma-based X-ray laser, simultaneously irradiated by an intense optical field of fundamental frequency. It is shown that for moderate plasma dispersion of the active medium at the frequency of the modulating optical field, the energy and relative amplitudes of the harmonics at the output of the medium are determined by their phases at the entrance to the medium, as well as by the time-delay of the harmonics with respect to the modulating field. These dependences are due to interference of high-order harmonics with a set of multi-frequency fields generated by each of the harmonics in the process of coherent scattering in a modulated active medium. The possibilities of using these effects to increase the efficiency of harmonic amplification, to control the harmonic spectrum, and determine the relative phases at the entrance to the medium are discussed on the example of the active medium of hydrogen-like Li{sup 2+} ions (with a 13.5 nm wavelength of an inverted transition). (paper)

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1996

Multiphoton Process and Anomalous Potential of Cell Membrane by Laser Radiation

In this paper, by the use of quantum biology and quantum optics, the laser induced potential variation of cell membrane has been studied. Theoretically, we have found a method of calculating the monophoton and multiphoton processes in the formation of the anomalous potential of cell membrane. In contrast with the experimental results, our numerical result is in the same order. Therefore, we have found the possibility of cancer caused by the laser induced anomalous cell potential.

Zhang, Kaixi↗
DOE OSTI2022

Journal paper

Laser technology is being widely studied for controlled energy deposition for a range of applications, including flow control, ignition, combustion, and diagnostics. The absorption and scattering of laser radiation by liquid droplets in aerosols affects propagation of the laser beam in the atmosphere, while the ignition and combustion characteristics in combustion chambers are influenced by the evaporation rate of the sprayed fuel. In this work, we present a mathematical model built on OpenFOAM for laser heating and evaporation of a single droplet in the diffusion-dominated regime taking into account absorption of the laser radiation, evaporation process, and vapor flow dynamics. The developed solver is validated against available experimental and numerical data for heating and evaporation of ethanol and water droplets. The two main regimes—continuous and pulsed laser heating—are explored. For continuous laser heating, the peak temperature is higher for larger droplets. For pulsed laser heating, when the peak irradiance is close to transition to the boiling regime, the temporal dynamics of the droplet temperature does not depend on the droplet size. With the empirical normalization of time, the dynamics of the droplet shrinkage and cooling are found to be independent of droplet sizes and peak laser intensities.

42 ENGINEERING↗
DOE OSTI2022

Numerical Modeling of Laser Heating and Evaporation of a Single Droplet

Laser technology is being widely studied for controlled energy deposition for a range of applications, including flow control, ignition, combustion, and diagnostics. The absorption and scattering of laser radiation by liquid droplets in aerosols affects propagation of the laser beam in the atmosphere, while the ignition and combustion characteristics in combustion chambers are influenced by the evaporation rate of the sprayed fuel. In this work, we present a mathematical model built on OpenFOAM for laser heating and evaporation of a single droplet in the diffusion-dominated regime taking into account absorption of the laser radiation, evaporation process, and vapor flow dynamics. The developed solver is validated against available experimental and numerical data for heating and evaporation of ethanol and water droplets. The two main regimes—continuous and pulsed laser heating—are explored. For continuous laser heating, the peak temperature is higher for larger droplets. For pulsed laser heating, when the peak irradiance is close to transition to the boiling regime, the temporal dynamics of the droplet temperature does not depend on the droplet size. With the empirical normalization of time, the dynamics of the droplet shrinkage and cooling are found to be independent of droplet sizes and peak laser intensities.

42 ENGINEERING↗
DOE OSTI2020

High-throughput experimentation for microstructural design in additively manufactured 316L stainless steel

In the present study, a combination of high-throughput (HT) and low-throughput (LT) techniques was used to rapidly determine the processing window and generate processing maps for Selective Laser Melting (SLM) of 316L stainless steel. The HT method includes the fabrication of hundreds of hex nut-shaped specimens, each processed with a unique combination of laser power, scanning speed, and hatch spacing. An easily removable scaffolding permitted rapid sample extraction from the base plate, thus saving machining cost and time. Hardness and immersion density measurements were used for HT characterization to identify a processing window for maximum strength and density. Within the defined processing window, a low-throughput (LT) microstructural interrogation of specimens were performed. The microstructural analysis included quantification at various length scales (i.e., grains size and morphology, texture, primary dendrite arm spacing, and melt pool geometry analysis). Microstructure-based processing maps as a function of volumetric energy density were generated. The combination of HT and LT methods produced a predictive relationship between hardness and primary dendrite arm spacing using a Hall-Petch relationship. A model is proposed to explain the dependence of microstructure on the melt pool geometry. Here, the HT method can be applied for the microstructural design of SLM-fabricated components in other alloys.

316L stainless steel↗
DOE OSTI2020

Temperature Measurement of Laser-Irradiated Metals Using Hyperspectral Imaging

Accurate noncontact surface-temperature measurements during laser-based materials processing remain challenging due to the difficulty of establishing reliable emissivity values as a function of temperature and wavelength. Direct measurement of emissivity is difficult, as the emissivity may be changing constantly in the laser-material interaction region, where the temperature gradients are extreme and surface displacement can complicate the measurement. Here, we present a hyperspectral imaging method using a multiwavelength camera to capture the spectral radiance in eight different bands and fit the wavelength-dependent radiance to Planck’s law. Time-resolved temperature measurements during microsecond pulsed-laser irradiation of a metal plate made of the titanium alloy Ti -6 Al -4 V provide temperature information about the irradiated surface with an estimated accuracy of ± 10 % . The extracted wavelength-dependent emissivity slope compares well with reported results for macroscale titanium melts obtained using IR spectroscopy, which measure temperature without any built-in assumptions about the emissivity. The results are directly applicable to temperature monitoring during welding, additive manufacturing, and semiconductor growth.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1993

Diamondlike carbon films as protective coatings for superconducting YBa2Cu3O7 films

We have investigated the use of diamondlike carbon (DLC) films for protecting superconducting YBCO films against degradation from exposure to moisture and acid. YBCO thin films on single crystal LaAlO3 and MgO substrates were deposited by laser ablation followed by DLC encapsulation. DLC films were deposited at pressures ranging from high vacuum to 0.1 Torr He. Substrate temperature was varied from 20 to 100 C during the deposition of DLC. The process compatibility of laser ablation was found convenient to sequentially deposit YBCO and DLC films from high purity stoichiometric targets. Epitaxial YBCO films on (100)LaAlO3 and (100)MgO substrates showed identical superconducting transitions before and after encapsulation by a DLC layer. The encapsulated films showed no degradation due to acid treatment or aging over a period of 45 days.

Ganapathi, L.↗
DOE OSTI2023

Selective laser melting of oxide dispersion strengthened MA956 alloy and its surface finishing by magnetic field assisted finishing

Selective laser melting (SLM) is a prominent metal additive manufacturing (AM) capable of processing a myriad of engineering materials with high precision and design freedom. However, similar to other AM processes, poor surface finishing has been an omnipresent problem in SLM technology. In this study, magnetic field assisted finishing (MAF) was used to finish SLM fabricated oxide dispersion strengthened (ODS) MA956, an iron-chromium-aluminum alloy. The effect of laser processing parameters on part density and surface roughness was first studied. Using a multi-objective optimization technique, the optimal parameters to obtain the highest density and lowest surface roughness were determined. Finally, MAF was applied to the parts built with the obtained optimal SLM parameters, but without significant improvement on the surfaces of as-printed samples. Hence, the surfaces of as-printed samples were post-processed (ground) to yield better initial surface conditions prior to MAF. The effect of initial roughness, iron particles size, and abrasive size on MAF performance was studied. Initial roughness had the most dominant effect followed by abrasive size. The underlying mechanism behind the dependency on initial roughness on final surface quality was analyzed by studying the change on the surface profiles with different starting initial roughness. The initial roughness required for MAF to be effective was determined. In conclusion, using the optimal processing conditions, MAF was applied to the post-processed samples to attain the final average surface roughness (R a ) as little as 0.36 μm starting from initial average roughness (R a ) of 1.53 μm.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Experiments on plasma arcs at a water–air interface

An exploding water plasma experiment at UCLA investigated the expansion and morphology of a fireball with and without an external magnetic field. Diagnostics include photographs and movies (which may be downloaded) acquired with a framing camera, magnetic probes, and visible light spectra. The expansion and internal magnetic fields are very different from the unmagnetized case when a magnetic field of order 300G is applied along the expansion axis. Visible light spectra are brighter and additional lines are seen in the presence of the magnetic field. The experiment can serve as a platform for studies of interfacial mixing and possibly shed light on very different processes such as laser target physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Femtosecond laser fabrication of nanograting-based distributed fiber sensors for extreme environmental applications

Abstract The femtosecond laser has emerged as a powerful tool for micro- and nanoscale device fabrication. Through nonlinear ionization processes, nanometer-sized material modifications can be inscribed in transparent materials for device fabrication. This paper describes femtosecond precision inscription of nanograting in silica fiber cores to form both distributed and point fiber sensors for sensing applications in extreme environmental conditions. Through the use of scanning electron microscope imaging and laser processing optimization, high-temperature stable, Type II femtosecond laser modifications were continuously inscribed, point by point, with only an insertion loss at 1 dB m −1 or 0.001 dB per point sensor device. High-temperature performance of fiber sensors was tested at 1000 °C, which showed a temperature fluctuation of ±5.5 °C over 5 days. The low laser-induced insertion loss in optical fibers enabled the fabrication of a 1.4 m, radiation-resilient distributed fiber sensor. The in-pile testing of the distributed fiber sensor further showed that fiber sensors can execute stable and distributed temperature measurements in extreme radiation environments. Overall, this paper demonstrates that femtosecond-laser-fabricated fiber sensors are suitable measurement devices for applications in extreme environments.

Wang, Mohan (ORCID:0000000166784993)↗
NASA NTRS2016

Laser Pulse Production for NASA's Global Ecosystem Dynamics Investigation (GEDI) Lidar

The Lasers and Electro-Optics Branch at Goddard Space Flight Center has been tasked with building the Lasers for the Global Ecosystems Dynamics Investigation (GEDI) Lidar Mission, to be installed on the Japanese Experiment Module (JEM) on the International Space Station (ISS). GEDI will use three NASA-developed lasers, each coupled with a Beam Dithering Unit (BDU) to produce three sets of staggered footprints on the Earth's surface to accurately measure global biomass. We will report on the design, assembly progress, test results, and delivery process of this laser system.

Laser Oscillator↗
NASA NTRS2016

Laser Pulse Production for NASA's Global Ecosystem Dynamics Investigation (GEDI) Lidar

The Lasers and Electro-Optics Branch at Goddard Space Flight Center has been tasked with building the Lasers for the Global Ecosystems Dynamics Investigation (GEDI) Lidar Mission, to be installed on the Japanese Experiment Module (JEM) on the International Space Station (ISS)1. GEDI will use three NASA-developed lasers, each coupled with a Beam Dithering Unit (BDU) to produce three sets of staggered footprints on the Earth's surface to accurately measure global biomass. We will report on the design, assembly progress, test results, and delivery process of this laser system.

Laser Oscillator↗
DOE OSTI2024

ExaFEL: extreme-scale real-time data processing for X-ray free electron laser science

ExaFEL is an HPC-capable X-ray Free Electron Laser (XFEL) data analysis software suite for both Serial Femtosecond Crystallography (SFX) and Single Particle Imaging (SPI) developed in collaboration with the Linac Coherent Lightsource (LCLS), Lawrence Berkeley National Laboratory (LBNL) and Los Alamos National Laboratory. ExaFEL supports real-time data analysis via a cross-facility workflow spanning LCLS and HPC centers such as NERSC and OLCF. Our work therefore constitutes initial path-finding for the US Department of Energy's (DOE) Integrated Research Infrastructure (IRI) program. We present the ExaFEL team's 7 years of experience in developing real-time XFEL data analysis software for the DOE's exascale supercomputers. We present our experiences and lessons learned with the Perlmutter and Frontier supercomputers. Furthermore we outline essential data center services (and the implications for institutional policy) required for real-time data analysis. Finally we summarize our software and performance engineering approaches and our experiences with NERSC's Perlmutter and OLCF's Frontier systems. This work is intended to be a practical blueprint for similar efforts in integrating exascale compute resources into other cross-facility workflows.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Strategies for Fabricating Molybdenum Structures Using Laser Powder Bed Fusion

Advances in manufacturing techniques are viewed as enabling technologies for development of high performance nuclear fuel forms that couple high uranium density with improvements to key properties such as thermal conductivity unattainable through conventional fabrication routes. Additive manufacturing (AM) enables the fabrication of complex fuel geometries that are difficult or impossible to achieve using conventional manufacturing methods. Melting-based AM processes, such as laser powder bed fusion (LPBF), provide high geometric resolution (>200 µm depending on the feature) across a variety of metal alloys, including those suitable for high-temperature fuel cladding applications, such as Nb, W, and Mo. Molybdenum is particularly attractive due to its high thermal conductivity, low thermal expansion, and excellent mechanical stability at elevated temperatures. However, its high melting temperature and brittle nature at low temperatures pose significant challenges during LPBF processing. Rapid solidification inherent to LPBF induces high residual stresses, often leading to post-solidification cracking, which limits the manufacturability of Mo components via this method.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

A dimensionless number for high-throughput design of multi-principal element alloys in directed energy deposition

The present study demonstrates the development of a dimensionless number to predict the build height in the additive manufacturing technique of directed energy deposition (DED). The build height can also be used to estimate the dendrite arm spacing and, thus, the cooling rate in the fabrication of samples. A baseline sample, 316L stainless steel, was used to fit the build height to the dimensionless number. A range of process parameters, including laser power, laser feed rate, powder flow rate, layer thickness, and hatch spacing, were varied. Based upon dendrite arm spacing, the estimated cooling rate varied between 102 and 104 K/s. Using the fitted relationship for the stainless steel, high-throughput (HT) processing of multi-principal element alloys (MPEAs) was performed. For this study, HT is the ability to fabricate a batch of 25 bulk samples (∼1 cm3) with different compositions within a 5-h period with ±10 at. % accuracy. A range of compositions using in situ alloying of elemental powders in the Fe–Ni–Cr–Mo system were made. The MPEAs' build height followed the same relationship to the dimensionless number as the 316L alloy. The dimensionless number predicts both macro and meso-scale features in HT processing, thus offering a design tool for choosing process parameters in DED additive manufacturing. Also, the ability to control or increase cooling rates can enhance the ability to promote metastability as well as control meso-scale chemical distributions of alloy samples.

Islam, Zahabul (ORCID:0000000169613209)↗