Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interfacial assembly”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3- δ cathodes infiltrated with samarium-doped cerium oxide for solid oxide fuel cells

Porous La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF) cathodes are coated with a thin film of Sm 0.2 Ce 0.8 O 1.95-δ (SDC) using a one-step infiltration process. Examination of the microstructures reveals that small SDC particles are formed on the surface of LSCF grains with a relatively narrow size distribution. Impedance analysis indicates that the SDC infiltration has dramatically reduced the polarization of LSCF cathode, reaching interfacial resistances of 0.074 and 0.44 Ω cm 2 at 750 °C and 650 °C, respectively, which are about half of those for LSCF cathode without infiltration of SDC. The activation energies of the SDC infiltrated LSCF cathodes are in the range of 1.42–1.55 eV, slightly lower than those for a blank LSCF cathode. The SDC infiltrated LSCF cathodes have also shown improved stability under typical SOFC operating conditions, suggesting that SDC infiltration improves not only power output but also performance stability and operational life.

30 DIRECT ENERGY CONVERSION↗

Interfacial Electron Transfer Dynamics Following Laser Flash Photolysis of [Ru(bpy)2((4,4'-PO3H2)2bpy)]2+ in TiO2 Nanoparticle Films in Aqueous Environments

Nanosecond laser flash photolysis has been used to investigate injection and back electron transfer from the complex [(Ru(bpy)2(4,4'-(PO3H2)2bpy)]2+ surface-bound to TiO2 (TiO2-RuII). The measurements were conducted under conditions appropriate for water oxidation catalysis by known single-site water oxidation catalysts. Systematic variations in average lifetimes for back electron transfer, <τbet>, were observed with changes in pH, surface coverage, incident excitation intensity, and applied bias. The results were qualitatively consistent with a model involving rate-limiting thermal activation of injected electrons from trap sites to the conduction band or shallow trap sites followed by site-to-site hopping and interfacial electron transfer, TiO2(e-)-Ru3+→TiO2-Ru2+. The appearance of pH-dependent decreases in the efficiency of formation of TiO2-Ru3+ and in incident-photon-to-current efficiencies with the added reductive scavenger hydroquinone point to pH-dependent back electron transfer processes on both the sub-nanosecond and millisecond–microsecond time scales, which could be significant in limiting long-term storage of multiple redox equivalents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tunable two-dimensional interfacial coupling in molecular heterostructures

Two-dimensional van der Waals heterostructures are of considerable interest for the next generation nanoelectronics because of their unique interlayer coupling and optoelectronic properties. Here, we report a modified Langmuir–Blodgett method to organize twodimensional molecular charge transfer crystals into arbitrarily and vertically stacked heterostructures, consisting of bis(ethylenedithio)tetrathiafulvalene (BEDT–TTF)/C 60 and poly (3-dodecylthiophene-2,5-diyl) (P3DDT)/C 60 nanosheets. A strong and anisotropic interfacial coupling between the charge transfer pairs is demonstrated. The van der Waals heterostructures exhibit pressure dependent sensitivity with a high piezoresistance coefficient of -4.4 × 10 -6 Pa -1 , and conductance and capacitance tunable by external stimuli (ferroelectric field and magnetic field). Density functional theory calculations confirm charge transfer between the n-orbitals of the S atoms in BEDT–TTF of the BEDT–TTF/C 60 layer and the π* orbitals of C atoms in C 60 of the P3DDT/C 60 layer contribute to the inter-complex CT. Thus, the two-dimensional molecular van der Waals heterostructures with tunable optical–electronic–magnetic coupling properties are promising for flexible electronic applications.

36 MATERIALS SCIENCE↗

Pre-Oxidized and Nitrided Stainless Steel Foil for Proton Exchange Membrane Fuel Cell Bipolar Plates: Part 2- Single-Cell Fuel Cell Evaluation of Stamped Plates

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr{sub 2}N, CrN, TiN, V{sub 2}N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of proton exchange membrane (PEM) single-cell fuel cell studies of stamped and pre-oxidized/nitrided developmental Fe-20Cr-4V weight percent (wt.%) and commercial type 2205 stainless steel alloy foils. The single-cell fuel cell behavior of the stamped and pre-oxidized/nitrided material was compared to as-stamped (no surface treatment) 904L, 2205, and Fe-20Cr-4V stainless steel alloy foils and machined graphite of similar flow field design. The best fuel cell behavior among the alloys was exhibited by the pre-oxidized/nitrided Fe-20Cr-4V, which exhibited {approx}5-20% better peak power output than untreated Fe-20Cr-4V, 2205, and 904L metal stampings. Durability was assessed for pre-oxidized/nitrided Fe-20Cr-4V, 904L metal, and graphite plates by 1000+ h of cyclic single-cell fuel cell testing. All three materials showed good durability with no significant degradation in cell power output. Post-test analysis indicated no metal ion contamination of the membrane electrode assemblies (MEAs) occurred with the pre-oxidized and nitrided Fe-20Cr-4V or graphite plates, and only a minor amount of contamination with the 904L plates.

30 DIRECT ENERGY CONVERSION↗

Impaired Protofibril Formation in Fibrinogen γN308K Is Due to Altered D:D and "A:a" Interactions

'A:a' knob-hole interactions and D:D interfacial interactions are important for fibrin polymerization. Previous studies with recombinant ?N308K fibrinogen, a substitution at the D:D interface, showed impaired polymerization. We examined the molecular basis for this loss of function by solving the crystal structure of ?N308K fragment D. In contrast to previous fragment D crystals, the ?N308K crystals belonged to a tetragonal space group with an unusually long unit cell (a = b = 95 Angstroms, c = 448.3 Angstroms). Alignment of the normal and ?N308K structures showed the global structure of the variant was not changed and the knob 'A' peptide GPRP was bound as usual to hole 'a'. The substitution introduced an elongated positively charged patch in the D:D region. The structure showed novel, symmetric D:D crystal contacts between ?N308K molecules, indicating the normal asymmetric D:D interface in fibrin would be unstable in this variant. We examined GPRP binding to ?N308K in solution by plasmin protection assay. The results showed weaker peptide binding, suggesting that 'A:a' interactions were altered. We examined fibrin network structures by scanning electron microscopy and found the variant fibers were thicker and more heterogeneous than normal fibers. Considered together, our structural and biochemical studies indicate both 'A:a' and D:D interactions are weaker. We conclude that stable protofibrils cannot assemble from ?N308K monomers, leading to impaired polymerization.

36 MATERIALS SCIENCE↗

Computational Investigation of Fuel Dispersal Phenomena during Large-Break Loss of Coolant Accident in Light-Water Reactors

In the event of cladding rupture, which could occur in light water reactor fuel assemblies during a loss-of-coolant accident (LOCA), fuel particles, along with fission gases, can be expelled into the reactor core from the fractured fuel rod. This expulsion of fragmented fuel particles, referred as fuel dispersal, is the subject of investigation to evaluate the safety implications of increasing fuel burnup in light water reactors, with a specific focus on fuel fragmentation, relocation, and dispersal. Particle trajectories and the resulting mass distribution of the settled particles within the reactor pressure vessel can pose a long-term cooling challenge for the reactor core. The fuel dispersal phenomenon is significantly influenced by the ejection characteristics of the fuel fragments, as well as the size and shape of the cladding rupture and fuel rod depressurization history during LOCA transients. In this study, the transport of fuel particles within a scaled 5 × 5 lattice of a pressurized water reactor rod bundle geometry is modeled through a two-fluid Eulerian framework that treats the gas and solid phases as interpenetrating continua. The required boundary conditions are evaluated from the fuel performance code BISON in a postulated large-break LOCA scenario. The modeling framework considers solid fuel particles as granular matter, interacting with the gaseous dry steam phase and fission gases through the governing interfacial momentum and energy exchange between the gas and solid phases. The simulation results provide the volume fraction of the solids settled on the bottom surface of the fuel bundle, quantifying the deposition within the bundle geometry.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Interfacial Fabrication of Supramolecular Polymer Networks Using Mussel-Inspired Catechol–Iron Complexes

The liquid–liquid interface provides a promising platform to construct supramolecular polymers and materials with advanced functions. However, supramolecular polymerization at the interface usually requires monomers with different or even orthogonal solubilities, which significantly limit the number of usable monomers. Here, in this work, we report a new strategy to construct supramolecular polymer networks at the oil–water interface using a water-soluble catechol–iron complex and an oil-soluble diend-functionalized polymer. Owing to the dynamic catechol–iron coordination bond and imine bond, the resulting supramolecular polymer networks demonstrate excellent dynamic features and responsiveness to different stimuli including the pH, redox, competing ligands, and temperature. With a supramolecular polymer network serving as a building block, emulsions and 2D films can be generated that have potential applications in encapsulation, release, and molecular separation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Liquid interfaces with pH-switchable nanoparticle arrays

Stimuli-responsive 2D nanoscale systems offer intriguing opportunities for creating switchable interfaces. At liquid interfaces, such systems can provide control over interfacial energies, surface structure, and rheological and transport characteristics, which is relevant, for example, to bio- and chemical reactors, microfluidic devices, and soft robotics. We explore the formation of a pH-responsive membrane formed from gold nanoparticles grafted with DNA (DNA–NPs) at a liquid–vapor interface. A DNA–NP 2D hexagonal lattice can be reversibly switched by pH modulation between an expanded state of non-connected nanoparticles at neutral pH and a contracted state of linked nanoparticles at acidic pH due to the AH + –H + A base pairing between A-motifs. Our in situ surface X-ray scattering studies reveal that the reversible lattice contraction can be tuned by the length of pH-activated linkers, with up to ~71% change in surface area.

59 BASIC BIOLOGICAL SCIENCES↗

Disentangling the Physical Processes Responsible for the Kinetic Complexity in Interfacial Electron Transfer of Excited Ru(II) Polypyridyl Dyes on TiO 2

Interfacial electron transfer at titanium dioxide (TiO 2 ) is investigated herein for a series of surface bound ruthenium-polypyridyl dyes whose metal-to-ligand charge-transfer state (MLCT) energetics are tuned through chemical modification. The 12 complexes are of the form Ru II (bpy-A)(L) 2 2+ , where bpy-A is a bipyridine ligand functionalized with phosphonate groups for surface attachment to TiO 2 . Functionalization of ancillary bipyridine ligands (L) enables the potential of the excited state Ru III/ * couple, E + / *, in 0.1 M perchloric acid (HClO 4 (aq)) to be tuned from –0.69 to –1.03 V vs NHE. Each dye is excited by a 200 fs pulse of light in the visible region of the spectrum and probed with a time-delayed supercontiuum pulse (350–800 nm). Decay of the MLCT excited-state absorption at 376 nm is observed without loss of the ground-state bleach, which is a clear signature of electron injection and formation of the oxidized dye. The dye-dependent decays are biphasic with time constants in the 3–30 and 30–500 ps range. The slower injection rate constant for each dye is exponentially distributed relative to E + / *. The correlation between the exponentially diminishing density of TiO 2 sub-band acceptor levels and injection rate is well described using Marcus–Gerischer theory, with the slower decay components being assigned to injection from the thermally equilibrated state and the faster components corresponding to injection from higher energy states within the 3 MLCT manifold. These results and detailed analyses incorporating molecular photophysics and semiconductor density of states measurements indicate that the multiexponential behavior that is often observed in interfacial injection studies is not due to sample heterogeneity. Rather, this work shows that the kinetic heterogeneity results from competition between excited-state relaxation and injection as the photoexcited dye relaxes through the 3 MLCT manifold to the thermally equilibrated state, underscoring the potential for a simple kinetic model to reproduce the complex kinetic behavior often observed at the interface of mesoporous metal oxide materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Final Technical Report

This report highlights of the last 3 years research. Discovery that one-layer (1L) epitaxial graphene plus one carbon interfacial buffer layer (BfL) , both grown by sublimation on SiC(0001), present a stiffness upon indentation similar/larger than bulk diamond and resist to perforation by a diamond indenter. Discovery of an sp 2 - sp 3 phase transformation upon indentation at room temperature of 1L+BfL epitaxial graphene on SiC, the new ultra-hard, ultra-stiff and insulating sp 3 phase was named Diamene . Demonstration of Å-Indentation (ÅI) measurements to measure the stiffness (up to 1 TPa) of ultra-thin (down to 1 atomic layer) films on substrates. First measurement by ÅI of the stiffness of Q-Carbon nano-filaments. Discovery of an oscillatory behavior in friction forces and work function values for even and odd number of layers in polycrystalline MoS 2 films, associated to the oscillatory piezoelectricity of the grains . Demonstration that monolayer MoS 2 can efficiently screen the vdW interaction of the underlying substrate with external systems. Identification of SiC buried terraces and graphene number of layers in a continuous film of epitaxial graphene on SiC by machine learning algorithms. New understanding of defects formation in monolayer MoS 2 . Demonstration of a new method based on thermal scanning probe lithography (t-SPL) for patterning electrodes on 2D materials overcoming EBL limitations . Demonstration of t-SPL for patterning nanoscale magnetic quantum waveguides . New understanding of how charged nanoparticles electrostatically assemble in 1D .

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Self-Assembly of Silica Nanoparticles at Water–Hydrocarbon Interfaces: Insights from In Operando Small-Angle X-ray Scattering Measurements and Molecular Dynamics Simulations

To achieve tunable controls on the interactions of siliceous materials in subsurface environments bearing water and hydrocarbons, it is essential to determine the influence of hydrocarbon–water interfaces on the self-assembly of the silica particles. The hydrophilic silica particle have a tendency to aggregate on the water front of the interface. Self-assembly of silica nanoparticles proceeds via the migration of these nanoparticles to the water–hydrocarbon interface followed by aggregation at the interface. Fractal-like morphologies of assembled silica nanoparticles at water–hydrocarbon interfaces are observed. Rapid assembly of the hydrophilic silica nanoparticles at water–hydrocarbon interfaces corresponds to an overall reduction in the surface tension of water–toluene and water–heptane systems. These studies demonstrate the silica aggregation that is the precursor of silica polymerization, or nucleation and growth is influenced by the presence of hydrocarbons in subsurface geologic environments. These insights were derived from in operando ultrasmall and small-angle X-ray scattering (USAXS/SAXS) measurements, cryo-scanning electron microscopy (Cryo-SEM) imaging, and classical molecular dynamics simulations. As a result, these studies are intended to inform current and future efforts aimed at tuning silica reactivity in subsurface geologic environments to enhance permeability, the design and use of silica-based proppants to enhance fractures, and the development of effective strategies to control silica-based scaling behavior in subsurface reservoirs.

42 ENGINEERING↗

Investigation of Electron Extraction and Protection Layers on Cu 2 O Photocathodes

Many semiconductor photoelectrodes used for solar fuel production require the addition of buffer and protection layers to enhance their solar-to-fuel conversion efficiency and long-term stability. For example, Cu 2 O, which is the most efficient oxide-based photocathode but suffers from photocorrosion, has been assembled with various buffer and protection layers to suppress photocorrosion and use more photoexcited electrons for useful reactions such as water reduction to H 2 . However, the abilities of various buffer and protection layers to extract electrons from Cu 2 O have never been directly evaluated. Instead, their abilities were estimated based on the photocurrent for water reduction after adding a hydrogen evolution catalyst on top of them. In these evaluations, as the photocurrent is affected not only by the buffer or protection layer but also by the catalyst, the ability of the buffer or protection layer to extract electrons from Cu 2 O could not be accurately determined or compared. Here, in this study, we demonstrate that 4-hydroxy-2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPOL), whose reduction rate is faster than the photocorrosion rate of Cu 2 O, can be used as an effective electron scavenger to directly evaluate any change caused by a buffer or protection layer in electron-hole separation in Cu 2 O. In particular, we compared the performances of ZnO and TiO 2 layers on Cu 2 O for extracting electrons and suppressing photocorrosion. We also compared the performances of TiO 2 layers prepared by electrodeposition and atomic layer deposition (ALD) to show that the deposition method can make a striking impact on the performance of the same TiO 2 because it can affect the critical characteristics of the layer (e.g., defect levels, conductivity, interfacial atomic arrangements) that govern interfacial charge transfer in multilayer photoelectrodes.

36 MATERIALS SCIENCE↗

Inner Layer Control of Performance in a Dye-Sensitized Photoelectrosynthesis Cell

Interfacial charge transfer and core-shell structures play important roles in dye-sensitized photoelectrosynthesis cells (DSPEC) for water splitting into H 2 and O 2 . An important element in the design of the photoanode in these devices is a core/shell structure which controls local electron transfer dynamics. Here, we introduce a new element, an internal layer of Al 2 O 3 lying between the Sb:SnO 2 /TiO 2 layers in a core/shell electrode which can improve photocurrents by up to 300%. In these structures, the results of photocurrent, transient absorption, and linear scan voltammetry measurements point to an important role for the Al 2 O 3 layer in controlling internal electron transfer within the core/shell structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructure Characterization of Fiber Laser Welds of S690QL High-Strength Steels

The use of fiber laser welding to join S690QL steels has attracted interest in the field of construction and assembly. Herein, 13-mm-thick S690QL welded joints were obtained without filler materials using the fiber laser. The as-welded microstructures and the impact energies of the joints were characterized and measured using electron microscopy in conjunction with high-resolution transmission electron images, X-ray diffraction, and impact tests. The results indicated that a single-sided welding technique could be used to join S690QL steels up to a thickness of 12 mm (fail to fuse the joint in the root) when the laser power is equal to 12 kW (scan speed 1 m/min). Double-side welding technique allows better weld penetration and better control of heat distribution. Observation of the samples showed that the fusion zone exhibited bainitic and martensitic microstructures with increased amounts of martensites (Ms) compared with the base materials. Also, the grains in the fusion zone increased in coarseness as the heat input was increased. The fusion zone exhibited increased hardness (397 HV{sub 0.2}) while exhibiting a simultaneous decrease in the impact toughness. The maximum impact energy value of 26 J was obtained from the single-side-welded sample, which is greater than those obtained from the double-side-welded samples (maximum of 18 J). Many more dislocations and plastic deformations were found in the fusion zone than the heat-affected zone in the joint, which hardened the joints and lowered the impact toughness. The microstructures characterized by FTEM–energy-dispersive X-ray spectrometer also exhibited laths of M, as well as stacking faults and dislocations featuring high-density, interfacial structure ledges that occur between the high-angle grain boundaries and the M and bainite.

36 MATERIALS SCIENCE↗

Low-Frequency Interlayer Raman Modes to Probe Interface of Twisted Bilayer MoS 2

A variety of van der Waals homo- and hetero- structures assembled by stamping monolayers together present optoelectronic properties suitable for diverse applications. Understanding the details of the interlayer stacking and resulting coupling is crucial for tuning these properties. Twisted bilayer transition metal dichalcogenides offer a great platform for developing a precise understanding of the structure/property relationship. Here, we study the low-frequency interlayer shear and breathing Raman modes (<50 cm-1) in twisted bilayer MoS 2 by Raman spectroscopy and first-principles modeling. Twisting introduces both rotational and translational shifts and significantly alters the interlayer stacking and coupling, leading to notable frequency and intensity changes of low-frequency modes. The frequency variation can be up to 8 cm-1 and the intensity can vary by a factor of ~5 for twisting near 0 and 60 , where the stacking is a mixture of multiple high-symmetry stacking patterns and is thus especially sensitive to twisting. Moreover, for twisting angles between 20 and 40 , the interlayer coupling is nearly constant since the stacking results in mismatched lattices over the entire sample. It follows that the Raman signature is relatively uniform. Interestingly, unlike the breathing mode, the shear mode is extremely sensitive to twisting: it disappears between 20 and 40 as its frequency drops to almost zero due to the stacking-induced mismatch. Note that for some samples, multiple breathing mode peaks appear, indicating non-uniform coupling across the interface. In contrast to the low-frequency interlayer modes, high-frequency intralayer Raman modes are much less sensitive to interlayer stacking and coupling, showing negligible changes upon twisting. Our research demonstrates the effectiveness of low-frequency Raman modes for probing the interfacial coupling and environment of twisted bilayer MoS2, and potentially other two-dimensional materials and heterostructures.

36 MATERIALS SCIENCE↗