Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “growth processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Effect of the number of pairs of the layers on the quality of the superlattices of the In{sub x}Ga{sub 1-x}As/GaAs/.../GaAs(001) type grown by molecular beam epitaxy under computer control

By the specified program of computer control over the growth process, superlattices of the In{sub x}Ga{sub 1-x}As/GaAs/.../GaAs(001) type with the number of alternating pairs N{sub 1} = 12, N{sub 2} = 6, and N{sub 3} = 3 were grown. Using the X-ray methods of quantitative analysis, the values of periods T{sub 1} = 22 nm, T{sub 2} = 22.5 nm, and T{sub 3} = 22.3 nm and the In content x{sub 1} = 0.09, x{sub 2} = 0.091, and x{sub 3} = 0.092 in these superlattices are measured. In the superlattice with N{sub 1} = 12, the plastic deformation is detected. In superlattices with N{sub 2} = 6 and N{sub 3} = 3, no plastic deformation during the growth was observed. The obtained magnitudes of the periods turned out smaller by a factor of approximately 2 and the alloy concentration turned out smaller by 1/3 than it was specified by the computer program. The measured and calculated values of elastic stresses turned out equal to {sigma}{sub 2N} = 2.43 x 10{sup 6} Pa and {sigma}{sup 2N-1} = -0.88 x 10{sup 9} Pa, at which the plastic deformation took place in the layers of the superlattice with N{sub 1} = 12. In superlattices with N{sub 2} = 6 and N{sub 3} = 3, the elastic stresses were {sigma}{sub 2N} = 1.96 x 10 6 Pa, {sigma}{sub 2N-1} = -1.45 x 10{sup 9} Pa and {sigma}{sub 2N} = 0.99 x 10{sup 6} Pa, {sigma}{sub 2N-1} = -1.88 x 10{sup 9} Pa, respectively. These stresses turned out insufficient to initiate the process of dislocation generation.

36 MATERIALS SCIENCE↗

Gas Phase Synthesis of Benzene via the Propargyl Radical Self-Reaction

Polycyclic Aromatic Hydrocarbons (PAHs) have been invoked in fundamental molecular mass growth processes in our galaxy. We provide compelling evidence of the formation of the very first ringed aromatic and building block of PAHs - benzene - via the self-recombination of two resonantly stabilized propargyl (C 3 H 3 ) radicals in dilute environments using isomer selective synchrotron-based mass spectrometry coupled to theoretical calculations. Along with benzene, three other structural isomers (1,5-hexadiyne, fulvene, 2-ethynyl-1,3-butadiene) and o-benzyne are detected and their branching ratios quantified experimentally and verified with the aid of computational fluid dynamics and kinetic simulations. Furthermore, these results uncover molecular growth pathways not only in interstellar, circumstellar, and solar systems environments, but also in combustion systems gaining us a better understanding of the hydrocarbon chemistry of our universe.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A theoretical and experimental study on manipulating the structure and properties of carbon nanotubes using substitutional dopants

We examine the possibility of controlling nanotube growth and simultaneously manipulating the nanotube properties by adding during the growth process, elements in minute amounts (such as nitrogen, phosphorous, and sulfur) that are different from carbon and the metal catalyst. This procedure is shown to be capable of producing bamboo-type morphologies, heterodoped carbon nanotubes, and Y-junctions. This also represents a critical step towards tailoring properties and controlling nanotube architectures, thus promoting the development of novel materials with unusual electronic applications. The underlying formation mechanisms that lead to the observed structures and morphologies are elucidated using wide-ranging electronic structure calculations that reveal the fundamentally different nature of nitrogen, phosphorous and sulfur during carbon nanotube growth.

36 MATERIALS SCIENCE↗

The onset and evolution of fatigue-induced abnormal grain growth in nanocrystalline Ni–Fe

Conventional structural metals suffer from fatigue-crack initiation through dislocation activity which forms persistent slip bands leading to notch-like extrusions and intrusions. Ultrafine-grained and nanocrystalline metals can potentially exhibit superior fatigue-crack initiation resistance by suppressing these cumulative dislocation activities. Prior studies on these metals have confirmed improved high-cycle fatigue performance. In the case of nano-grained metals, analyses of subsurface crack initiation sites have indicated that the crack nucleation is associated with abnormally large grains. But, these post-mortem analyses have led to only speculation about when abnormal grain growth occurs (e.g., during fatigue, after crack initiation, or during crack growth). In this study, a recently developed synchrotron X-ray diffraction technique was used to detect the onset and progression of abnormal grain growth during stress-controlled fatigue loading. Our study provides the first direct evidence that the grain coarsening is cyclically induced and occurs well before final fatigue failure—our results indicate that the first half of the fatigue life was spent prior to the detectable onset of abnormal grain growth, while the second half was spent coarsening the nanocrystalline structure and cyclically deforming the abnormally large grains until crack initiation. Post-mortem fractography, coupled with cycle-dependent diffraction data, provides the first details regarding the kinetics of this abnormal grain growth process during high-cycle fatigue testing. Finally, precession electron diffraction images collected in a transmission electron microscope after the in situ fatigue experiment also confirm the X-ray evidence that the abnormally large grains contain substantial misorientation gradients and sub-grain boundaries.

36 MATERIALS SCIENCE↗

TeO{sub 2} liquid phase: Viscosity measurements and evaluation of the thermal conductivity from crystal growth experiments

Current applications of paratellurite TeO{sub 2} in optics and nuclear physics require improving the yield and optical quality of synthesized single crystals. Modelling of the growth process is a useful tool for such purpose, however, involving the knowledge of several thermodynamic parameters of both solid and liquid phase of the compound. This work describes the determination of two main unknown ones, namely dynamic viscosity {eta} and thermal conductivity {lambda}{sub l} of the liquid phase. Measurements of {eta} are performed by means of a specifically designed apparatus; over a 40 K temperature interval above the melting point we find a mean value of 0.028 Pa.s. This data is used in commercial software to depict the evolution of the solid-liquid interface in our Bridgman growth set-up. Comparison of the distribution of defects observed in grown ingots with the results of modelling allows estimating {lambda}{sub l} as lying in the range 3.50-3.75 W m{sup -1} K{sup -1}.

36 MATERIALS SCIENCE↗

Pseudo-halide anion engineering for efficient quasi-2D Ruddlesden-Popper tin perovskite solar cells

Quasi-two-dimensional (2D) organic-inorganic hybrid tin perovskites have emerged as promising alternatives to lead-based perovskites in thin-film photovoltaics because of their reduced toxicity and improved stability. However, the undesired small n-value 2D phases and disordered crystal orientation enormously restrict the efficiency of quasi-2D tin perovskite solar cells (PSCs) due to uncontrollable nucleation and crystal growth processes. Here, we propose a mixed pseudo-halide anion engineering approach by using acetate (Ac - ) and tetrafluoroborate (BF 4 - ) anions to make quasi-2D Ruddlesden-Popper perovskites with a target formula of PEA 2 FA 4 Sn 5 I 16 . We find that the mixed Ac - and BF 4 - anions can not only promote homogeneously distributed PEA + cations in the precursor by effectively breaking the PEA + ···PEA + stacking but also retard the crystallization process by coordinating with unbonded SnI 2 , thereby, significantly reducing small n-value 2D phases, improving the crystal orientation, and suppressing the Sn 2+ oxidation. The resulting PSC exhibits up to 9% power conversion efficiency and 400 h stability.

36 MATERIALS SCIENCE↗

Confinement of excited states in two-dimensional, in-plane, quantum heterostructures

Two-dimensional (2D) semiconductors are promising candidates for optoelectronic application and quantum information processes due to their inherent out-of-plane 2D confinement. In addition, they offer the possibility of achieving low-dimensional in-plane exciton confinement, similar to zero-dimensional quantum dots, with intriguing optical and electronic properties via strain or composition engineering. However, realizing such laterally confined 2D monolayers and systematically controlling size-dependent optical properties remain significant challenges. Here, we report the observation of lateral confinement of excitons in epitaxially grown in-plane MoSe 2 quantum dots (~15-60 nm wide) inside a continuous matrix of WSe 2 monolayer film via a sequential epitaxial growth process. Various optical spectroscopy techniques reveal the size-dependent exciton confinement in the MoSe 2 monolayer quantum dots with exciton blue shift (12-40 meV) at a low temperature as compared to continuous monolayer MoSe 2 . Finally, single-photon emission (g 2 (0) ~ 0.4) was also observed from the smallest dots at 1.6 K. Our study opens the door to compositionally engineered, tunable, in-plane quantum light sources in 2D semiconductors.

42 ENGINEERING↗

Growth kinetics and micromorphology of NH{sub 4}Cl:Mn{sup 2+} crystals formed in the NH{sub 4}Cl-MnCl{sub 2}-H{sub 2}O-CONH{sub 3} system

The growth kinetics and elementary growth processes on the surface of NH{sub 4}Cl:Mn{sup 2+} heterogeneous crystals formed in the NH{sub 4}Cl-MnCl{sub 2}-H{sub 2}O-CONH{sub 3} system are experimentally studied. It is found that a change in the composition of complexes in an NH{sub 4}Cl crystal from Mn(NH{sub 4}){sub 2}Cl{sub 4} {center_dot} 2H{sub 2}O to MnCl{sub 2} {center_dot} 2CONH{sub 3} leads to the occurrence of a local maximum in the kinetic curve and a change in the shape of dislocation growth centers from flat to conical. The growth kinetics of {l_brace}100{r_brace} faces of heterogeneous NH{sub 4}Cl:Mn{sup 2+} crystals is described within the Bliznakov model using the Fowler-Guggenheim adsorption isotherm, which takes into account the lateral interaction of adsorbed particles.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Arsenic redistribution after solid phase epitaxial regrowth of shallow pre-amorphized silicon layers

The behavior of ultra shallow ion implants of arsenic in Si following solid phase epitaxial re-growth process is reported. A 16 nm amorphous layer was created by ion implantation of Si{sup +} at energy 5 keV and a dose 1 Multiplication-Sign 10{sup 15} at/cm{sup 2}. As ion were implanted at 2 keV using 3 different doses: 1 Multiplication-Sign 10{sup 14}, 5 Multiplication-Sign 10{sup 14} and 1 Multiplication-Sign 10{sup 15} at/cm{sup 2}. The resulting As distributions, confined in the amorphous layer, were thermally treated at 550 Degree-Sign C for 5-300 s in order to electrically activate dopant atoms. Crystal re-growth and As redistribution was investigated by secondary ion mass spectrometry and medium energy ion scattering. A growth rate depending on the As concentration was observed, the rate being slower for higher As content. Arsenic re-distribution to the surface and at the end-of-range defects was observed and a segregation model was developed. Finally, the substitutional fraction of As atoms was related to sheet resistance measurements revealing a higher fraction of electrically active dopant atoms in pre-amorphized samples compared to not pre-amorphized.

36 MATERIALS SCIENCE↗

Synthesis of the Orthorhombic Dy{sub 1−x}Ho{sub x}MnO{sub 3} Single Crystals and Study of Their Magnetic Properties

In this report, we prepared for the first time the orthorhombic Dy{sub 1−x}Ho{sub x}MnO{sub 3} single crystals with x = 0, 0.1, 0.2, 0.3, and 0.4 using the flux technique. The post-growth processing and chemical and structural characterization of the synthesized samples were performed. Also, we examined the samples obtained by their magnetic properties and the magnetic anisotropy in wide ranges of temperatures and magnetic fields.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Production of fibers by a floating zone fiber drawing technique

A CO2 laser heated, floating zone fiber growth process was developed. The resulting Al2O3 fibers exhibited the high room temperature strengths for large diameter fibers as well as high specific creep rupture strengths observed at 1093 C and 1316 C (2000 F and 2400 F). Single crystal fibers of TiC and Y2O3 were also grown. An optical system was developed to focus four CO2 laser beams onto the surface of a feed rod permitting the formation of highly controllable molten zones. The optical system permitted energy densities and angle of incidence of the beams to be adjusted over wide ranges. This optical system was incorporated into a controlled atmosphere, fiber growth furnace. The two principal advantages of a CO2 laser heat source are that ambient atmospheres may be freely selected to optimize fiber properties and the laser has no inherent temperature limit, so extremely high melting point materials can be melted. Both advantages were demonstrated.

Haggerty, J. S.↗

LDRD 191204: Optimization of Sputtered Aluminum Nitride for the Seeding of Metal Organic Chemical Vapor Deposition Gallium Nitride Films

GaN-on-Si combines the wide bandgap advantages of GaN with the cost and scaling advantages of Si. Sputtered A1N is an attractive nucleation layer material because it reduces Al diffusion into the Si and eliminates a time-intensive preconditioning step in the GaN growth process, but is limited by the poor film quality of PVD A1N films deposited on Si substrates. Sputtering also offers a large degree of control over A1N film properties, including control of the intrinsic stress using substrate biasing. Doping the A1N films with Sc improves the lattice match to A1GaN and GaN films by expanding the a-axis and c-axis lattice parameters. A1N and A1 0.88 Sc 0.12 N films have been grown on silicon, metal, and sapphire substrates and characterized for properties such as stress, grain size, roughness, and film orientation for use as nucleation layers for MOCVD GaN growth.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Space-based crystal growth and thermocapillary flow

The demand for larger crystals is increasing especially in applications associated with the electronic industry, where large and pure electronic crystals (notably silicon) are the essential material to make high-performance computer chips. Crystal growth under weightless conditions has been considered an ideal way to produce bigger and hopefully better crystals. One technique which may benefit from a microgravity environment is the float-zone crystal-growth process, a containerless method for producing high-quality electronic material. In this method, a rod of material to be refined is moved slowly through a heating device which melts a portion of it. Ideally, as the melt resolidifies it does so as a single crystal which is then used as substrate for building microelectronic devices. The possibility of contamination by contact with other material is reduced because of the 'float' configuration. However, since the weight of the material contained in the zone is supported by the surface-tension force, the size of the resulting crystal is limited in Earth-based productions; in fact, some materials have properties which prevent this process from being used to manufacture crystals of reasonable size. Consequently, there has been a great deal of interest in exploiting the microgravity environment of space to grow larger size crystals of electronic material using the float-zone method. In addition to allowing larger crystals to be grown, a microgravity environment would also significantly reduce the magnitude of convection induced by buoyancy forces during the melting state. This type of convection was once thought to be at least partially responsible for the presence of undesirable nonuniformities--called striations--in material properties observed in float-zone material. However, past experiments on crystal growth under weightless conditions found that even with the absence of gravity, the float-zone method sometimes still results striations. It is believed that another mechanism is playing a dominant role in the microgravity environment.

Shen, Yong-Hong↗

Liquid encapsulated Czochralski growth of low dislocation GaAs

The availability of high-quality, large-diameter GaAs substrates is key to the successful development and production of high-speed GaAs devices and high-efficiency GaAs solar cells. The liquid encapsulated Czochralski (LEC) technique has provided a means for producing large-diameter GaAs. Progress in improving the LEC growth process which has resulted in 3-inch GaAs crystals with exceptionally low dislocation densities and reduced propensity for twinning is reported. Undoped, semi-insulating GaAs ingots were grown in a Melbourn high-pressure LEC system. The effects of seed perfection, seed necking, cone angle, melt stoichiometry, ambient pressure, thickness of the B2O3 encapsulating layer, and diameter control on the dislocation density were investigated. The material was characterized by preferential etching and X-ray topography. It is shown that 3-inch diameter substrates can be produced with dislocation densities as low as 6000 per sq cm through proper selection and control of growth parameters. Also, the incidence of twinning can be reduced significantly by growing from slightly As-rich melts.

Kirkpatrick, C. G.↗

Reactive sputter magnetron reactor for preparation of thin films and simultaneous in situ structural study by X-ray diffraction

The purpose of the designed reactor is (i) to obtain polycrystalline and/or amorphous thin films by controlled deposition induced by a reactive sputtering magnetron and (ii) to perform a parallel in situ structural study of the deposited thin films by X-ray diffraction, in real time, during the whole growth process. The designed reactor allows for the control and precise variation of the relevant processing parameters, namely, magnetron target-to-sample distance, dc magnetron voltage, and nature of the gas mixture, gas pressure and temperature of the substrate. On the other hand, the chamber can be used in different X-ray diffraction scanning modes, namely, {theta}-2{theta} scanning, fixed {alpha}-2{theta} scanning, and also low angle techniques such as grazing incidence small angle X-ray scattering and X-ray reflectivity. The chamber was mounted on a standard four-circle diffractometer located in a synchrotron beam line and first used for a preliminary X-ray diffraction analysis of AlN thin films during their growth on the surface of a (100) silicon wafer.

36 MATERIALS SCIENCE↗

In situ X-ray investigation of changing barrier growth temperatures on InGaN single quantum wells in metal-organic vapor phase epitaxy

The effects of GaN quantum barriers with changing growth temperatures on the interfacial characteristics of GaN/InGaN single quantum well (SQW) grown on GaN templates by metalorganic vapour phase epitaxy were in situ investigated by X-ray crystal truncation rod (CTR) scattering and X-ray reflectivity measurements at growth temperature using a laboratory level X-ray diffractometer. Comparing the curve-fitting results of X-ray CTR scattering spectra obtained at growth temperature with that at room temperature, the In{sub x}Ga{sub 1-x}N with indium composition less than 0.11 was stabile of the indium distribution at the interface during the whole growth processes. By using several monolayers thickness GaN capping layer to protect the InGaN well layer within temperature-ramping process, the interfacial structure of the GaN/InGaN SQW was drastically improved on the basis of the curve-fitting results of X-ray CTR scattering spectra, and the narrow full width at half-maximum and strong luminous intensity were observed in room temperature photoluminescence spectra.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Vanadium-Doped Cadmium Manganese Telluride (Cd1-X Mn (X) Te) Crystals as X- and Gamma-Ray Detectors

CdMnTe offers several potential advantages over CdZnTe as a room- temperature gamma-ray detector, but many drawbacks in its growth process impede the production of large, defect-free single crystals with high electrical resistivity and high electron lifetimes. Here, we report our findings of the defects in several vanadium-doped as-grown as well as annealed Cd{sub 1-x} Mn{sub x} Te crystals, using etch pit techniques. We carefully selected single crystals from the raw wafer to fabricate and test as a gamma-ray detector. We describe the quality of the processed Cd{sub 1-x} Mn{sub x} Te surfaces, and compare them with similarly treated CdZnTe crystals. We discuss the characterization experiments aimed at clarifying the electrical properties of fabricated detectors, and evaluate their performance as gamma-ray spectrometers.

36 MATERIALS SCIENCE↗

Preparation and characterization of Co single-crystal thin films with hcp, fcc and bcc structures

Co crystals with three different structures are realized in the form of single-crystal thin films hetero-epitaxially grown on single-crystal substrates by ultrahigh vacuum rf magnetron sputtering. hcp-, fcc-, and bcc-Co single-crystal films are formed on Cr(211){sub bcc}, Cu(100){sub fcc}, and GaAs(110){sub B3}, respectively. The film growth process is studied by RHEED, and the lattice constants of these Co films are determined by x-ray diffraction. The magnetization properties of these thin films are reflecting the magnetocrystalline anisotropies of Co crystals with the easy magnetization axes along hcp<0001>, fcc<111>, and bcc<100> directions.

36 MATERIALS SCIENCE↗