SEARCH · Engineering Papers

Results for “forward modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

All sources NASA NTRS DOE OSTI

NASA NTRS1984

Wind-tunnel free-flight investigation of a model of a forward-swept-wing fighter configuration

A wind-tunnel free-flight investigation was conducted to study the dynamic stability characteristics of a model of a forward-swept-wing fighter-airplane configuration at high angles of attack. Various other wind-tunnel techniques employed in the study included static- and dynamic- (forced-oscillation) force tests, free-to-roll tests, and flow-visualization tests. A unique facet of the study was the extreme level of static pitch instability (in excess of negative 32-percent static margin) inherent in the airframe design which precluded free-flight testing without stability augmentation in pitch. Results are presented which emphasize the high-angle-of-attack aerodynamics and the vehicle-component contributions to these characteristics. The effects of these aerodynamic characteristics on the high-angle-of-attack flying qualities of the configuration are discussed in terms of results of the wind-tunnel free-flight tests.

Murri, D. G.↗

NASA NTRS1993

Calibration of the forward-scattering spectrometer probe - Modeling scattering from a multimode laser beam

Scattering calculations using a detailed model of the multimode laser beam in the forward-scattering spectrometer probe (FSSP) were carried out using a recently developed extension to Mie scattering theory. From this model, new calibration curves for the FSSP were calculated. The difference between the old calibration curves and the new ones is small for droplet diameters less than 10 microns, but the difference increases to approximately 10 percent at diameters of 50 microns. When using glass beads to calibrate the FSSP, calibration errors can be minimized by using glass beads of many different diameters, over the entire range of the FSSP. If the FSSP is calibrated using one-diameter glass beads, then the new formalism is necessary to extrapolate the calibration over the entire range.

Hovenac, Edward A.↗

NASA NTRS1993

Calibration of the Forward-scattering Spectrometer Probe: Modeling Scattering from a Multimode Laser Beam

Scattering calculations using a more detailed model of the multimode laser beam in the forward-scattering spectrometer probe (FSSP) were carried out by using a recently developed extension to Mie scattering theory. From this model, new calibration curves for the FSSP were calculated. The difference between the old calibration curves and the new ones is small for droplet diameters less than 10 micrometers, but the difference increases to approximately 10% at diameters of 50 micrometers. When using glass beads to calibrate the FSSP, calibration errors can be minimized, by using glass beads of many different diameters, over the entire range of the FSSP. If the FSSP is calibrated using one-diameter glass beads, then the new formalism is necessary to extrapolate the calibration over the entire range.

Hovenac, Edward A.↗

NASA NTRS2005

Mapping From an Instrumented Glove to a Robot Hand

An algorithm has been developed to solve the problem of mapping from (1) a glove instrumented with joint-angle sensors to (2) an anthropomorphic robot hand. Such a mapping is needed to generate control signals to make the robot hand mimic the configuration of the hand of a human attempting to control the robot. The mapping problem is complicated by uncertainties in sensor locations caused by variations in sizes and shapes of hands and variations in the fit of the glove. The present mapping algorithm is robust in the face of these uncertainties, largely because it includes a calibration sub-algorithm that inherently adapts the mapping to the specific hand and glove, without need for measuring the hand and without regard for goodness of fit. The algorithm utilizes a forward-kinematics model of the glove derived from documentation provided by the manufacturer of the glove. In this case, forward-kinematics model signifies a mathematical model of the glove fingertip positions as functions of the sensor readings. More specifically, given the sensor readings, the forward-kinematics model calculates the glove fingertip positions in a Cartesian reference frame nominally attached to the palm. The algorithm also utilizes an inverse-kinematics model of the robot hand. In this case, inverse-kinematics model signifies a mathematical model of the robot finger-joint angles as functions of the robot fingertip positions. Again, more specifically, the inverse-kinematics model calculates the finger-joint commands needed to place the fingertips at specified positions in a Cartesian reference frame that is attached to the palm of the robot hand and that nominally corresponds to the Cartesian reference frame attached to the palm of the glove. Initially, because of the aforementioned uncertainties, the glove fingertip positions calculated by the forwardkinematics model in the glove Cartesian reference frame cannot be expected to match the robot fingertip positions in the robot-hand Cartesian reference frame. A calibration must be performed to make the glove and robot-hand fingertip positions correspond more precisely. The calibration procedure involves a few simple hand poses designed to provide well-defined fingertip positions. One of the poses is a fist. In each of the other poses, a finger touches the thumb. The calibration subalgorithm uses the sensor readings from these poses to modify the kinematical models to make the two sets of fingertip positions agree more closely.

Goza, Michael↗

NASA NTRS2023

Developing a Radar Signal Simulator for the Community Radiative Transfer Model

Active radar instruments provide vertically resolved clouds and precipitation measurements that cannot be provided by the passive instruments. These active measurements are not conventionally assimilated into the data assimilation systems because of the lack of fast forward radiative transfer models and also difficulties in the error modelling of the measurements. This paper describes the development, evaluation, and sensitivity analysis for a forward radar model implemented in the Community Radiative Transfer Model (CRTM). The scattering properties required by the forward model are provided by the hydrometeor lookup tables that were generated using the discrete dipole approximation. The model is able to calculate both the reflectivity and the attenuated reflectivity for any given radar instrument at any given zenith angles as long as CRTM instrument specific coefficients are available. The evaluation using CloudSat measurements shows a very good agreement between the simulations and measurements as long as the input profiles of hydrometeors are consistent with the measured reflectivity profiles. Major sources contributing to the differences between the measured and simulated reflectivities are input hydrometeor profiles, scattering lookup tables, lack of melting layer in the forward model, CRTM scattering solvers, and attenuation calculations. In addition to the forward model, both Tangent Linear and Adjoint of the model are also implemented and tested within CRTM. These components may be required by some data assimilation systems for the assimilation of radar measurements.

radar↗

DOE OSTI2025

Statistical model of the stimulated forward Brillouin scattering driven by a randomized laser beam in plasma

The modeling of a spatially incoherent laser beam remains a central problem of the parametric instabilities in the context of inertial confinement fusion. This letter gives a simplified and comprehensive overview of the recent analytical developments regarding the modeling of these laser beams and a comparison with a dedicated experiment. Our model accounts for the first time for the statistical standard deviation of the gain and accurately captures the entanglement between wave mixing processes and the speckle correlations thus resolving the longstanding contradictions between the random phase approximation and the model of independent speckles. It is successfully compared to a recent laser beam spray experiment and the associated paraxial simulations, demonstrating that backscattering predictions require accounting for the beam spray. Furthermore, our framework thus provides a way to evaluate and guide the analysis of parametric instabilities in high laser energy experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1985

Forward and reverse transfer function model synthesis

A process for synthesizing a mathematical model for a linear mechanical system using the forward and reverse Fourier transform functions is described. The differential equation for a system model is given. The Bode conversion of the differential equation, and the frequency and time-domain optimization matching of the model to the forward and reverse transform functions using the geometric simplex method of Nelder and Mead (1965) are examined. The effect of the window function on the linear mechanical system is analyzed. The model is applied to two examples; in one the signal damps down before the end of the time window and in the second the signal has significant energy at the end of the time window.

Houghton, J. R.↗

DOE OSTI2021

Physics‐based iterative reconstruction for dual‐source and flying focal spot computed tomography

Purpose For single‐source helical Computed Tomography (CT), both Filtered‐Back Projection (FBP) and statistical iterative reconstruction have been investigated. However, for dual‐source CT with flying focal spot (DS‐FFS CT), a statistical iterative reconstruction that accurately models the scanner geometry and acquisition physics remains unknown to researchers. Therefore, our purpose is to present a novel physics‐based iterative reconstruction method for DS‐FFS CT and assess its image quality. Methods Our algorithm uses precise physics models to reconstruct from the native cone‐beam geometry and interleaved dual‐source helical trajectory of a DS‐FFS CT. To do so, we construct a noise physics model to represent data acquisition noise and a prior image model to represent image noise and texture. In addition, we design forward system models to compute the locations of deflected focal spots, the dimension, and sensitivity of voxels and detector units, as well as the length of intersection between x‐rays and voxels. The forward system models further represent the coordinated movement between the dual sources by computing their x‐ray coverage gaps and overlaps at an arbitrary helical pitch. With the above models, we reconstruct images by an advanced Consensus Equilibrium (CE) numerical method to compute the maximum a posteriori estimate to a joint optimization problem that simultaneously fits all models. Results We compared our reconstruction with Siemens ADMIRE, which is the clinical standard hybrid iterative reconstruction (IR) method for DS‐FFS CT, in terms of spatial resolution, noise profile, and image artifacts through both phantoms and clinical scan datasets. Experiments show that our reconstruction has a higher spatial resolution, with a Task‐Based Modulation Transfer Function (MTF task ) consistently higher than the clinical standard hybrid IR. In addition, our reconstruction shows a reduced magnitude of image undersampling artifacts than the clinical standard. Conclusions By modeling a precise geometry and avoiding data rebinning or interpolation, our physics‐based reconstruction achieves a higher spatial resolution and fewer image artifacts with smaller magnitude than the clinical standard hybrid IR.

Wang, Xiao↗

NASA NTRS2002

Vortex Wake Geometry of a Model Tilt Rotor in Forward Flight

The vortex wake trajectory from one rotor of a 0.25-scale V-22 tiltrotor model was measured for four test conditions in the NASA Ames 40- by 80-Foot Wind Tunnel. Vortex wake images were acquired using a laser light sheet and video camera. Wake trajectories were constructed by extracting vortex positions from the video images. Wake trajectories were also calculated using the comprehensive analysis CAMRAD II. Measured and calculated wake geometries exhibit similar trends when advance ratio is varied at fixed thrust or when thrust is varied at fixed advance ratio.

Yamauchi, G. K.↗

NASA NTRS1993

Takeoff/approach noise for a model counterrotation propeller with a forward-swept upstream rotor

A scale model of a counterrotating propeller with forward-swept blades in the forward rotor and aft-swept blades in the aft rotor (designated F39/A31) has been tested in the NASA Lewis 9- by 15-Foot Anechoic Wind Tunnel. This paper presents aeroacoustic results at a takeoff/approach condition of Mach 0.20. Laser Doppler velocimeter results taken in a plane between the two rotors are also included to quantify the interaction flow field. The intention of the forward-swept design is to reduce the magnitude of the forward rotor tip vortex and/or wakes which impinge on the aft rotor, thus lowering the interaction tone levels. A reference model propeller (designated F31/A31), having aft-swept blades in both rotors, was also tested. Aeroelastic performance of the F39/A31 propeller was disappointing. The forward rotor tip region tended to untwist toward higher effective blade angles under load. The forward rotor also exhibited steady state blade flutter at speeds and loadings well below the design condition. The noise results, based on sideline acoustic data, show that the interaction tone levels were up to 8 dB higher with the forward-swept design compared to those for the reference propeller at similar operating conditions, with these tone level differences extending down to lower propeller speeds where flutter did not occur. These acoustic results are for a poorly-performing forward-swept propeller. It is quite possible that a properly-designed forward-swept propeller would exhibit substantial interaction tone level reductions.

Woodward, Richard P.↗

NASA NTRS1988

Interference by rain scatter

The data from Japan and the U.S. (the Virginia Precipitation Scatter Experiment) show excellent agreement between the two-component rain scatter model predictions and bistatic scatter measurements. In employing the model, all the scattering geometries should be classified as backscattering as defined by Crane (1974). The forward scatter model should only be used for great circle paths with both antennas pointed at the horizon and at each other in a typical troposcatter communication system geometry. The forward scatter model can also be used for main-lobe, side-lobe coupling when one antenna is pointed toward the other along the great circle path. The forward scatter observations made over the Prospect Hill - Mt Tug path show that the two-component model is incomplete. Much stronger signals were observed at Ku-band than expected based on simultaneous C-band measurements. The discrepancies may be due to: (1) scattering by ice/snow at height (posssible in April) at the 1 km height of the scattering volume), (2) the coherent effects of turbulent fluctuations in the hydrometeor number densities and (3) errors in the modeling of the statistical relationship between attenuation along the path and scattering in the common volume.

Crane, Robert K.↗

NASA NTRS1992

Diabatic dynamic initialization

A generalized dynamical adjustment procedure was applied to a diabatic model to produce balanced initial conditions. Namely, backward adiabatic model integration is followed by forward diabatic model integration, with a high frequency (low pass) filter in the form of the Euler-backward time differencing scheme being applied throughout the whole integration. As a result of the application of such a diabatic dynamic initialization procedure within the Goddard Laboratory for Atmospheres (GLA) 4-D data assimilation system, the following properties of forecasts from initialized fields are achieved right from the beginning of the usual forecast integration: (1) the forecast tendencies (and fields) are free of any noise due to imbalance in initial conditions; (2) the shocks related to an initial imbalance between model physics and dynamics, and especially the substantial initial imbalance of precipitation and evaporation fields, or the initial spin-up effect, are practically removed. Diabatic dynamic initialization has been compared with implicit nonlinear normal mode initialization, and found to be superior in removing the initial spin-up effect, and also in improving the tropical structure. The diabatic dynamic initialization procedure was successfully tested for the GLA system with the use of all conventional data and the GLA satellite data retrievals. It allows a smooth data insertion without any shocks or imbalances, which is highly desirable for efficient functioning of 4-D data assimilation systems. The developed initialization procedure is computationally efficient and in principle easily applicable to different forecast models.

Fox-Rabinovitz, Michael S.↗

NASA NTRS1993

Diabatic dynamic initialization

A version of the dynamical adjustment procedure is generalized in order to make the procedure applicable to a diabatic model. In this new initialization procedure, backward adiabatic model integration is followed by forward diabatic model integration, with a high-frequency (low-pass) time filter in the form of the Euler backward time-differencing scheme applied throughout the integration. The new procedure was applied to the Goddard Laboratory for Atmospheres 4D data-assimilation system. It was found that, right from the beginning of the forecast integration, the forecast tendencies (and fields) were free of any noise due to imbalance in initial conditions, and the shocks related to an initial imbalance between model physics and dynamics, or the initial spinup effect, were practically removed.

Fox-Rabinovitz, Michael S.↗

NASA NTRS2018

A SysML Model Template for NASA Concurrent Engineering Studies

Systems Engineers at NASA Langley’s Engineering Design Studio (EDS) have been developing a SysML** template that models both the EDS concurrent engineering study process and the system of interest for the study. Specifically, the model template is used to develop end-to-end space-based mission concepts. The model template evolved through targeted use and technical feedback during several EDS studies in 2016-17. This year, a model template version was completed that is being tested for use throughout EDS studies. It features ease of navigation through the documented study process to create the logistical articles (e.g. session agenda) and technical articles (e.g. system requirements) connected in the study SysML model, resulting in demonstrable and trackable relationships between the system design and the study goals and objectives. The model template allows easy release of the system of interest portion at the end of the EDS study. The customers may use this as a starter model as their project moves forward. The model template design details and the motivation for them will be explained in this paper. This will be followed by the results of the first trials of the model template in an EDS study, and discussion of the integration of this template into the NASA MBSE Community of Practice.

Infeld, Samantha I.↗

NASA NTRS1993

Takeoff/approach noise for a model counterrotation propeller with a forward-swept upstream rotor

Woodward, Richard P.↗

NASA NTRS2014

Forward Bay Cover Separation Modeling and Testing for the Orion Multi-Purpose Crew Vehicle

Spacecraft multi‐body separation events during atmospheric descent require complex testing and analysis to validate the flight separation dynamics model and to verify no recontact. NASA Orion Multi‐Purpose Crew Vehicle (MPCV) teams examined key model parameters and risk areas to develop a robust but affordable test campaign in order to validate and verify the Forward Bay Cover (FBC) separation event for Exploration Flight Test‐1 (EFT‐1). The FBC jettison simulation model is highly complex, consisting of dozens of parameters varied simultaneously, with numerous multi‐parameter interactions (coupling and feedback) among the various model elements, and encompassing distinct near‐field, mid‐field, and far‐field regimes. The test campaign was composed of component‐level testing (for example gas‐piston thrusters and parachute mortars), ground FBC jettison tests, and FBC jettison air‐drop tests that were accomplished by a highly multi‐disciplinary team. Three ground jettison tests isolated the testing of mechanisms and structures to anchor the simulation models excluding aerodynamic effects. Subsequently, two air‐drop tests added aerodynamic and parachute parameters, and served as integrated system demonstrations, which had been preliminarily explored during the Orion Pad Abort‐1 (PA‐1) flight test in May 2010. Both ground and drop tests provided extensive data to validate analytical models and to verify the FBC jettison event for EFT‐1, but more testing is required to support human certification, for which NASA and Lockheed Martin are applying knowledge from Apollo and EFT‐1 testing and modeling to develop a robust but affordable human spacecraft capability.

Ali, Yasmin↗

NASA NTRS1977

Wind tunnel and ground static tests of a .094 scale powered model of a modified T-39 lift/cruise fan V/STOL research airplane

Ground static and wind tunnel test of a scale model modified T-39 airplane are reported. The configuration in the nose and replacement of the existing nacelles with tilting lift/cruise fans. The model was powered with three 14 cm diameter tip driven turbopowered simulators. Forces and moments were measured by an internal strain guage balance. Engine simulator thrust and mass flow were measured by calibrated pressure and temperature instrumentation mounted downstream of the fans. The low speed handling qualities and general aerodynamic characteristics of the modified T-39 were defined. Test variables include thrust level and thrust balance, forward speed, model pitch and sideslip angle at forward speeds, model pitch, roll, and ground height during static tests, lift/cruise fan tilt angle, flap and aileron deflection angle, and horizonal stabilizer angle. The effects of removing the landing gear, the lift/cruise fans, and the tail surfaces were also investigated.

Hunt, D.↗

NASA NTRS2015

Forward Bay Cover Separation Modeling and Testing for the Orion Multi-Purpose Crew Vehicle

Spacecraft multi-body separation events during atmospheric descent require complex testing and analysis to validate the flight separation dynamics models used to verify no re-contact. The NASA Orion Multi-Purpose Crew Vehicle (MPCV) architecture includes a highly-integrated Forward Bay Cover (FBC) jettison assembly design that combines parachutes and piston thrusters to separate the FBC from the Crew Module (CM) and avoid re-contact. A multi-disciplinary team across numerous organizations examined key model parameters and risk areas to develop a robust but affordable test campaign in order to validate and verify the FBC separation event for Exploration Flight Test-1 (EFT-1). The FBC jettison simulation model is highly complex, consisting of dozens of parameters varied simultaneously, with numerous multi-parameter interactions (coupling and feedback) among the various model elements, and encompassing distinct near-field, mid-field, and far-field regimes. The test campaign was composed of component-level testing (for example gas-piston thrusters and parachute mortars), ground FBC jettison tests, and FBC jettison air-drop tests that were accomplished by a highly multi-disciplinary team. Three ground jettison tests isolated the testing of mechanisms and structures to anchor the simulation models excluding aerodynamic effects. Subsequently, two air-drop tests added aerodynamic and parachute elements, and served as integrated system demonstrations, which had been preliminarily explored during the Orion Pad Abort-1 (PA-1) flight test in May 2010. Both ground and drop tests provided extensive data to validate analytical models and to verify the FBC jettison event for EFT-1. Additional testing will be required to support human certification of this separation event, for which NASA and Lockheed Martin are applying knowledge from Apollo and EFT-1 testing and modeling to develop a robust human-rated FBC separation event.

Ali, Yasmin↗