SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A number of upcoming NASA missions require energy storage devices which display high energy density and can effectively operate at low temperature. Lithium-ion batteries have been identified as the most promising technology which can meet these stringent requirements.
Silicon anodes for lithium-ion batteries (LIBs) have the potential for higher energy density compared to conventionally used graphite-based LIB anodes. However, silicon anodes exhibit poor cycle and calendar lifetimes due to mechanical instabilities and high chemical and electrochemical reactivity with the carbonate-based electrolytes that are typically used in LIBs. In this work, we synthesize a pitch carbon-coated silicon nanoparticle composite active material for LIB anodes that exhibits reduced chemical reactivity with carbonate-based electrolytes compared to an uncoated silicon anode. Silicon primary particle sizes less than 10 nm diameter minimize micro-scale mechanical degradation of the anode composite, while conformal coatings of pitch carbon minimize the parasitic reactions between the silicon and the electrolyte. When matched with a high voltage NMC622 (LiNi 0.6 Mn 0.2 Co 0.2 O 2 ) cathode, the pitch carbon-coated silicon anode retains approximately 75% of its initial capacity at the end of 1000 cycles. Increasing the areal loading of the pitch carbon-coated silicon anodes to realize energy density improvements over graphite anodes results in severe mechanical degradation on the electrode level, highlighting a remaining challenge to be addressed in future work.
Lithium–sulfur (Li–S) batteries are promising candidates for next-generation energy storage systems due to their high theoretical energy density and the low cost of sulfur. However, slow conversion kinetics between the insulating S and lithium sulfide (Li 2 S) remains as a technical challenge. In this work, we report a catalyst featuring nickel (Ni) single atoms and clusters anchored to a porous hydrogen-substituted graphdiyne support (termed Ni@HGDY), which is incorporated in Li 2 S cathodes. The rapidly synthesized catalyst was found to enhance ionic and electronic conductivity, decrease the reaction overpotential, and promote more complete conversion between Li 2 S and sulfur. The addition of Ni@HGDY to commercial Li 2 S powder enabled a capacity of over 516 mAh g Li 2 S –1 at 1 C for over 125 cycles, whereas the control Li 2 S cathode managed to maintain just over 200 mAh g Li 2 S –1 . In conclusion, these findings highlight the efficacy of Ni as a metal catalyst and demonstrate the promise of HGDY in energy storage devices.
Lithium-ion rechargeable batteries have been demonstrated to have high energy density, high voltage, and excellent cycle life which make this technology more attractive than competing systems such as Ni-Cd and Ni-H2.
A facile, scalable, wastewater-free synthesis of high energy density LiMn0.5Fe0.5PO4 (LMFP) cathodes with high electrode press density is achieved by employing the spinel LiMnFeO4 (LMFO) as a precursor.
The development of a high energy density battery is discussed. Tests were conducted on a 1400 AH cell and they include: drop tests, crush tests, vibration and shock tests, hydrostatic pressure effects, charge current tests, and discharge tests. None of these tests led to a venting or explosion of the cell. Criteria are presented for extending RV safety of a 1400 AH cell.
Enabling the lithium metal anode has been the holy grail for improving the energy density for the next generation advanced batteries. Developing electrolytes that will suppress Li dendrite growth and provide sufficient ionic conductivity remains a major challenge in this field. In this study, we develop a polymer–ceramic composite electrolyte for lithium metal batteries. The polymer matrix is a vinyl ethylene carbonate (VEC) based single-ion-conducting polymer electrolyte. The ceramic filler is a Li 7 La 3 Zr 0.5 Nb 0.5 Ta 0.5 Hf 0.5 O 12 high-entropy Li-garnet (HE Li-garnet) ceramic, which is less prone to surface Li 2 CO 3 formation compared to Al-doped Li garnets. The addition of HE Li-garnet leads to a 7-fold increase in the ionic conductivity (8.6 × 10 −5 S cm −1 at 30 °C) compared to the pure polymer, while maintaining a high Li + transference of 0.73. Proton nuclear magnetic resonance and thermogravimetric analysis results suggest that the addition of HE Li-garnet results in a lower degree of polymerization of VEC, leaving more unpolymerized VEC monomers in the matrix, serving as the governing mechanism for conductivity enhancement. The favorable interactions between HE Li-garnet particles and the polymer matrix lead to a stable and well-mixed composite with 2-fold enhancement of storage modulus at 40 °C. The simultaneous ion transport and mechanical property enhancement significantly improves the composite electrolyte's dendrite resistance and cycle life in Li symmetric cells. This work highlights the positive role HE Li-garnet can play in improving polymer electrolytes to enable lithium metal anodes.
Abstract In pursuit of the highest possible energy density, researchers shift their focus to the ultimate anode material, lithium metal (Li 0 ), and high‐capacity cathode materials with high nickel content (Ni > 80%). The combination of these aggressive electrodes presents unprecedented challenges to the electrolyte. Here, we report a hybrid electrolyte consisting of a highly fluorinated ionic liquid and a weakly solvating fluorinated ether, whose hybridization structure enables the reversible operation of a battery chemistry based on Li 0 and LiNiO 2 (Ni = 100%), delivering nearly theoretical capacity of the latter (up to 249 mAh g −1 ) for >300 cycles with retention of 78.6% and in absence of unwanted morphological changes in both electrodes. Extensive characterization assisted by molecular dynamic simulation and density functional theory calculations reveals the function of the fluorinated ether to be far more profound than simple dilution and viscosity reduction. Instead, it induces drastic changes in Li + ‐solvation environment, the consequence of which engenders simultaneous stabilization of electrode/electrolyte and interfacing via formation of respective interfacial chemistries. This study further unlocks fundamental knowledge underneath the prevailing “diluent strategy” that is extensively applied by the electrolyte researchers and opens more design space for the next‐generation electrolytes and interphases for these coveted battery chemistries.
Abstract All‐solid‐state battery with Li metal anode is a promising rechargeable battery technology with high energy density and improved safety. Currently, the application of Li metal anode is plagued by the failure at the interfaces between lithium metal and solid electrolyte (SE). However, little is known about the defects at Li–SE interfaces and their effects on Li cycling, impeding further improvement of Li metal anodes. Herein, by performing large‐scale atomistic modeling of Li metal interfaces with common SEs, we discover that lithium metal forms an interfacial defect layer of nanometer‐thin disordered lithium at the Li–SE interfaces. This interfacial defect Li layer is highly detrimental, leading to interfacial failure such as pore formation and contact loss during Li stripping. By systematically studying and comparing incoherent, coherent, and semi‐coherent Li–SE interfaces, we find that the interface with good lattice coherence has reduced Li defects at the interface and has suppressed interfacial failure during Li cycling. Our finding discovered the critical roles of atomistic lithium defects at interfaces for the interfacial failure of Li metal anode, and motivates future atomistic‐level interfacial engineering for Li metal anode in solid‐state batteries.
Not Available
Abstract Microparticulate silicon (Si), normally shelled with carbons, features higher tap density and less interfacial side reactions compared to its nanosized counterpart, showing great potential to be applied as high-energy lithium-ion battery anodes. However, localized high stress generated during fabrication and particularly, under operating, could induce cracking of carbon shells and release pulverized nanoparticles, significantly deteriorating its electrochemical performance. Here we design a strong yet ductile carbon cage from an easily processing capillary shrinkage of graphene hydrogel followed by precise tailoring of inner voids. Such a structure, analog to the stable structure of plant cells, presents ‘imperfection-tolerance’ to volume variation of irregular Si microparticles, maintaining the electrode integrity over 1000 cycles with Coulombic efficiency over 99.5%. This design enables the use of a dense and thick (3 mAh cm–2) microparticulate Si anode with an ultra-high volumetric energy density of 1048 Wh L–1 achieved at pouch full-cell level coupled with a LiNi0.8Co0.1Mn0.1O2 cathode.
Robust lithium/solid electrolyte/iodine electrochemical cells that offer significant advantages over commercial lithium/ iodine cells have been developed. At room temperature, these cells can be discharged at current densities 10 to 30 times those of commercial lithium/iodine cells. Moreover, from room temperature up to 80 C, the maximum discharge-current densities of these cells exceed those of all other solid-electrolyte-based cells. A cell of this type includes a metallic lithium anode in contact with a commercial flexible solid electrolyte film that, in turn, is in contact with an iodine/ graphite cathode. The solid electrolyte (the chemical composition of which has not been reported) offers the high ionic conductivity needed for high cell performance. However, the solid electrolyte exhibits an undesirable chemical reactivity to lithium that, if not mitigated, would render the solid electrolyte unsuitable for use in a lithium cell. In this cell, such mitigation is affected by the formation of a thin passivating layer of lithium iodide at the anode/electrolyte interface. Test cells of this type were fabricated from iodine/graphite cathode pellets, free-standing solid-electrolyte films, and lithium-foil anodes. The cathode mixtures were made by grinding together blends of nominally 10 weight percent graphite and 90 weight percent iodine. The cathode mixtures were then pressed into pellets at 36 kpsi (248 MPa) and inserted into coin-shaped stainless-steel cell cases that were coated with graphite paste to minimize corrosion. The solid-electrolyte film material was stamped to form circular pieces to fit in the coin cell cases, inserted in the cases, and pressed against the cathode pellets with polyethylene gaskets. Lithium-foil anodes were placed directly onto the electrolyte films. The layers described thus far were pressed and held together by stainless- steel shims, wave springs, and coin cell caps. The assembled cells were then crimped to form hermetic seals. It was found that the solid electrolyte films became discolored within seconds after they were placed in contact with the cathodes - a result of facile diffusion of iodine through the solid electrolyte material (see figure).
We report Lithium (Li) metal shows great potential for achieving high-energy-density rechargeable batteries. However, the practical applications of Li-metal batteries are still challenged by the formation of Li dendrites and unstable solid-electrolyte interphase (SEI) on metallic Li. Herein, a thin covalent organic framework layer is in situ fabricated on Li (COF-Li) to suppress Li dendrite growth and mitigate the side reaction on the Li anode. The COF has a periodic and uniform porosity, allowing for selectively sieving Li ions and guiding a uniform Li deposition. As a result, the COF-Li exhibits a non-dendrite morphology during repeated Li plating/stripping and demonstrates a remarkable cycle life over 13 200 h with an extremely low overpotential of only 16 mV at a high current density of 10 mA cm -2 and a high areal capacity of 10 mAh cm -2 .
Electric Vehicle (EV) sales and adoption have seen a significant growth in recent years, thanks to advancements and cost reduction in lithium-ion battery technology, attractive performance of EVs, governments' incentives, and the push to reduce greenhouse gases and pollutants. In this article, we will explore the progress in lithium-ion batteries and their future potential in terms of energy density, life, safety, and extreme fast charge. Here we will also discuss material sourcing, supply chain, and end-of-life-cycle management as they have become important considerations in the ecosystem of batteries for the sustained growth and adoption of EVs. With significant government and private sector investments in research and development, processing, and manufacturing and advances in anodes (lithium and silicon), cathodes (high nickel), designs, supply chain development, and the circularity of lithium-ion batteries, lithium-based batteries are on track to make EVs mainstream, addressing climate concerns of fossil-fueled vehicles.
NbSe3 exhibits superior characteristics such as high capacity, high volumetric and gravimetric energy densities, and high discharge rate capability, as compared to other intercalating cathodes. This paper reports the preparation, characterization, and performance of NbSe3. Several electrochemical techniques, such as cyclic voltammetry, constant-current/constant-potential discharges, dc potentiodynamic scans, ac impedance, and ac voltammetry, have been used to give insight to the mechanisms of intercalation of three lithiums with NbSe3 and also into the rate determining process in the reduction of NbSe3.
The US Department of Energy (DOE) has a rich history of funding key innovations in batteries through multiple programs, including the Energy Efficiency and Renewable Energy programs sponsored by the Vehicle Technologies Office and Advanced Manufacturing Office. These DOE-sponsored innovations have been critical in lowering the cost of lithium-ion batteries to less than $160/kWh and increasing their energy density to more than 250 Wh/kg, enhancing the nation’s electrification system and achieving higher degrees of decarbonization. These investments continue to be crucial for positioning the United States as the hub for the most cumulative battery R&D programs worldwide. However, major breakthroughs in battery manufacturing are still needed to enable an electrified future evolving to predominantly incorporate rechargeable lithium-ion batteries. This will require a strong battery manufacturing base that will not only enable cutting-edge advancements in materials and manufacturing sciences but will also allow the United States to become a world leader in this fast-growing area. This review aims at supporting DOE’s Advanced Technology Vehicle Manufacturing Loan Program to give technology background and information that can be used to develop the basis for loan topics and evaluate battery applications. Such a program can represent a significant stride toward reinforcing the US position in advanced manufacturing by introducing artificial intelligence, machine learning, and sensing and smart controls to facilitate, expedite, and lead the battery industry by 2030.
Lithium spinels (Li MM 'O 4 ) are an important class of mixed-cation materials that have found uses in batteries, catalysis, and optics. Postspinels are a series of related framework structures with the AMM 'O 4 host composition that are formed with larger A -site cations, typically under high pressure. Postspinels have one-dimensional tunnel structures with pores that are larger than those in spinel and triangular in cross-section, but they are relatively unexplored as intercalation electrodes. While lithium postspinels have been previously found to be thermodynamically stable only at high pressures, we have identified a synthetic pathway that produces the lithium-containing materials at ambient pressure using an ion-exchange process from the corresponding sodium postspinels. Here, in this work, we report the synthesis and a survey of the electrochemical properties of 10 new lithium CaFe 2 O 4 -type postspinel compounds where M = Mn 3+ , V 3+ , Cr 3+ , Rh 3+ , Fe 2+ , Mg 2+ , Co 2+ and M ' = Ti 4+ and/or Sn 4+ . Although complete delithiation is not achieved during electrochemical cycling, many of the lithium postspinels have substantial charge storage capacity in Li battery cells owing to the ability of the large framework tunnels to accommodate more than one lithium ion per formula unit. Multiple redox couples are accessed for LiMnSnO 4 , Li 0.96 Mn 0.96 Sn 1.04-x Ti x O 4 , Li 0.96 V 0.96 Ti 1.04 O 4 , Li 0.96 Cr 0.96 Ti 1.04 O 4 , and LiFe 0.5 Ti 1.5 O 4 . Compositions with moderate or poor lithium cyclability are also discussed for comparison. Redox mechanisms and trends are identified by comparing this new redox-active framework to related spinels, ramsdellites, and 'Na 0.44 MnO 2 ' structures, and from density functional theory (DFT) electronic structures. Operando diffraction shows complex structural responses to lithium insertion and extraction in this postspinel framework. A DFT framework was proposed to identify promising lithium postspinel phases that could be accessed metastably under ambient pressure conditions and to assess their stability to lithium insertion and extraction. This work suggests that CaFe 2 O 4 -type hosts are a promising new class of lithium-ion energy storage materials.
All-solid-state battery with Li metal anode is a promising rechargeable battery technology with high energy density and improved safety. Currently, the application of Li metal anode is plagued by the failure at the interfaces between lithium metal and solid electrolyte (SE). However, little is known about the defects at Li–SE interfaces and their effects on Li cycling, impeding further improvement of Li metal anodes. Herein, by performing large-scale atomistic modeling of Li metal interfaces with common SEs, we discover that lithium metal forms an interfacial defect layer of nanometer-thin disordered lithium at the Li–SE interfaces. Further, this interfacial defect Li layer is highly detrimental, leading to interfacial failure such as pore formation and contact loss during Li stripping. By systematically studying and comparing incoherent, coherent, and semi-coherent Li–SE interfaces, we find that the interface with good lattice coherence has reduced Li defects at the interface and has suppressed interfacial failure during Li cycling. Our finding discovered the critical roles of atomistic lithium defects at interfaces for the interfacial failure of Li metal anode, and motivates future atomistic-level interfacial engineering for Li metal anode in solid-state batteries.