SEARCH · Engineering Papers

Results for “corrosion control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Measuring the Electrochemical Corrosion of 233U-doped UO2 in a Microfluidic Device

We have developed a microfluidic, ‘particle-attached microfluidic electrochemical’ device, or PAMEC, that uses microgram quantities of radioactive materials, such as uranium dioxide (UO2), rather than bulk specimens to both observe electrochemical changes and measure spectroscopic properties. The PAMEC device reduces the need for running experiments in a shielded facility and allows for in-operando, real-time investigations of electrochemical properties and morphological changes of micrograms of particles. This novel design offers a promising platform to investigate spent nuclear fuel (SNF) and other nuclear materials under various controlled condition, and to provide insights to nuclear waste management, and fuel performance

Electrochemistry↗

DOE OSTI2024

Environmental Validation of Materials and Design Concepts to Enable Operational Flexibility of Existing Coal Power Plants

Increasingly, coal-fired power plants are required to balance power grids by compensating for the variable electricity supply from renewable energy sources. Fossil-fueled power plants, originally designed to be base loaded, will increasingly need to operate on a load following or cyclic basis. This demanding requirement for operational flexibility will need to be evaluated for resilience to frequent start-ups, meeting major and rapid load changes, and providing frequency control duties. Our research objective was to evaluate and improve flexibility of existing power plants by improving and redesigning components and deﬁning new operational strategies, with acceptable impacts on component life, efficiency and emissions.

20 FOSSIL-FUELED POWER PLANTS↗

NASA NTRS1988

Experimental results on atomic oxygen corrosion of silver

The results of an experimental study of the reaction kinetics of silver with atomic oxygen in 10 degree increments over the temperature range of 0 to 70 C is reported. The silver specimens, of the order of 10,000 A in thickness, were prepared by thermal evaporation onto 3 inch diameter polished silicon wafers. There were later sliced into pieces having surface areas of the order of 1/4 to 1/2 square inch. Atomic oxygen was generated by a gas discharge in a commercial plasmod asher operating in the megahertz frequency range. The sample temperature within the chamber was controlled by means of a thermoelectric unit. Exposure of the silver specimens to atomic oxygen was incremental, with oxide film thickness measurements being carried out between exposures by means of an automated ellipsometer. For the early growth phase, the data can be described satisfactorily by a logarithmic growth law: the oxide film thickness increases as the logarithm of the exposure time. Furthermore, the oxidation process is thermally activated, the rate increasing with increasing temperature. However, the empirical activation energy parameter deduced from Arrhenius plots is quite low, being of the order of 0.1 eV.

Fromhold, Albert T.↗

DOE OSTI2022

Evaluation of PV Module Packaging Strategies of Monofacial and Bifacial PERC Using Degradation Pathway Network Modeling

As the PV industry is rapidly expanding, it is important to thoroughly investigate the long-term impact of packaging strategies on the performance of PV modules. In this study, the variants in sets differ on the basis of manufacturer (A/B), encapsulant (EVA/POE), rear encapsulant (UV-cutoff/opaque/transparent), module architecture (GB/DG) and cell type (monofacial/bifacial). The minimodules were exposed for 2520 hours in modified damp heat, with or without full spectrum light. Every 504 hours, stepwise electrical characterization techniques were employed to track changes in minimodules. Degradation pathway modeling using network structural equation modeling was employed to study pairwise relationships between variables and service lifetime prediction in minimodules. Through this study, differences in quality control are identified in minimodules made by different manufacturers. Minimodules with UV-cutoff rear encapsulant show relatively better stability, whereas the ones with opaque rear encapsulant show greater power loss. In addition, GB having UV-cutoff rear encapsulation and GB with POE having opaque rear encapsulation were identified to be stable as they lack a best model fit. Here, the primary power loss mechanism in degrading variants is interconnect corrosion.

14 SOLAR ENERGY↗

NASA NTRS2014

International Space Station (ISS) Orbital Replaceable Unit (ORU) Wet Storage Risk Assessment

The International Space Station (ISS) Program requested the NASA Engineering and Safety Center (NESC) to evaluate the risks posed by the practice of long-term wet storage of ISS Environmental Control and Life Support (ECLS) regeneration system orbital replacement units (ORUs). The ISS ECLS regeneration system removes water from urine and humidity condensate and converts it into potable water and oxygen. A total of 29 ORUs are in the ECLS system, each designed to be replaced by the ISS crew when necessary. The NESC assembled a team to review the ISS ECLS regeneration system and evaluate the potential for biofouling and corrosion. This document contains the outcome of the evaluation.

Squire, Michael D.↗

DOE OSTI2021

Measuring the residual stress and stress-corrosion cracking susceptibility of additively manufactured 316L by ASTM G36-94

Residual stress is a contributor to stress-corrosion cracking (SCC) and a common byproduct of additive manufacturing (AM). In this work, the relationship between residual stress and SCC susceptibility in laser powder bed fusion AM 316L stainless steel was studied through immersion in saturated boiling magnesium chloride per ASTM G36-94. The residual stress was varied by changing the sample height for the as-built condition and additionally by heat treatments at 600, 800, and 1200 °C to control, and in some cases reduce, residual stress. In general, all samples in the as-built condition showed susceptibility to SCC with the thinner, lower residual stress samples showing shallower cracks and crack propagation occurring perpendicular to melt tracks due to local residual stress fields. The heat-treated samples showed a reduction in residual stress for the 800 and 1200 °C samples. Both were free of cracks after >300 hours of immersion in MgCl 2 , while the 600 °C sample showed similar cracking to their as-built counterpart. Geometrically necessary dislocation (GND) density analysis indicates that the dislocation density may play a major role in the SCC susceptibility.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Electrodeposited Sn–Cu@Sn dendrites for selective electrochemical CO 2 reduction to formic acid

Large-scale CO 2 electrolysis can be applied to store renewable energy in chemicals. Recent developments in gas diffusion electrodes now enable a commercially relevant current density. However, the low selectivity of the CO 2 reduction reaction (CO 2 RR) still hinders practical applications. The selectivity of the CO 2 RR highly depends on the electrocatalyst. Sn catalysts are considered promising cathode materials for the production of formic acid. The selectivity of Sn catalysts can be regulated by controlling their morphology or alloying them with secondary metals. In this work, we enhanced the selectivity of CO 2 reduction to formic acid by synthesizing Sn–Cu@Sn dendrites that have a core@shell architecture. The Sn–Cu@Sn dendrites were prepared by a scalable electro-deposition method. The electronic structure was modified to suppress a reaction pathway for CO production on the Sn surface. Notably, the Sn shell inhibited the cathodic corrosion of Cu during the CO 2 RR. On a gas diffusion electrode, the Sn–Cu@Sn dendrites exhibited 84.2% faraday efficiency to formic acid for 120 h with high stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2005

NASA Tech Briefs, January 2005

Topics covered include: Fiber-Optic Sensor Would Monitor Growth of Polymer Film; Sensors for Pointing Moving Instruments Toward Each Other; Pd/CeO2/SiC Chemical Sensors; Microparticle Flow Sensor; Scattering-Type Surface-Plasmon-Resonance Biosensors; Diode-Laser-Based Spectrometer for Sensing Gases; Improved Cathode Structure for a Direct Methanol Fuel Cell; X-Band, 17-Watt Solid-State Power Amplifier; Improved Anode for a Direct Methanol Fuel Cell; Tools for Designing and Analyzing Structures; Interactive Display of Scenes with Annotations; Solving Common Mathematical Problems; Tools for Basic Statistical Analysis; Program Calculates Forces in Bolted Structural Joints; Integrated Structural Analysis and Test Program; Molybdate Coatings for Protecting Aluminum Against Corrosion; Synthesizing Diamond from Liquid Feedstock; Modifying Silicates for Better Dispersion in Nanocomposites; Powder-Collection System for Ultrasonic/Sonic Drill/Corer; Semiautomated, Reproducible Batch Processing of Soy; Hydrogen Peroxide Enhances Removal of NOx from Flue Gases; Subsurface Ice Probe; Real-Time Simulation of Aeroheating of the Hyper-X Airplane; Using Laser-Induced Incandescence To Measure Soot in Exhaust; Method of Real-Time Principal-Component Analysis; Insect-Inspired Flight Control for Unmanned Aerial Vehicles; Domain Compilation for Embedded Real-Time Planning; Semantic Metrics for Analysis of Software; Simulation of Laser Cooling and Trapping in Engineering Applications; Large Fluvial Fans and Exploration for Hydrocarbons; Doping-Induced Interband Gain in InAs/AlSb Quantum Wells; Development of Software for a Lidar-Altimeter Processor; Upgrading the Space Shuttle Caution and Warning System; and Fractal Reference Signals in Pulse-Width Modulation.

Source record↗

DOE OSTI2024

Distributed strain sensing using Bi-metallic coated fiber optic sensors embedded in stainless steel

Silica fiber optic sensors are resistant to corrosive environments and high temperatures, making them attractive candidates for harsh conditions found in nuclear and aerospace industries. Moreover, fibers can be deployed remotely for continuous measuring of spatially distributed temperatures and strains. Here, this study investigated embedding a Ni/Cu bi-metallic coated fiber in a stainless-steel 316 (SS316) matrix using laser powder bed fusion towards functionalizing metal components for site-specific health monitoring. The embedded fiber was continuously interrogated during controlled heating to 1000°C. The measured fiber strains were similar to the expected differential thermal strains between the fiber and the SS316 matrix, until divergent behavior was observed at temperatures >500°C. No debonding at the matrix–coating–fiber interfaces was observed during microscopy, but significant interactions between the coatings and matrix resulted in diffusion-driven chemistry variations and Kirkendall void formation. Applying the strain-lag theory revealed plastic behavior in the Ni coating at temperatures >500°C, limiting the strain transfer to the fiber at higher temperatures. It was estimated that the elastic modulus in the Ni coating had decreased from ~200 GPa at room temperature to below 40 GPa, starting at 600°C. The low elastic modulus above 600°C is within the margin of what the tangent modulus would be in the case of bilinear isotropic hardening. Regardless of the divergent strain transfer at higher temperatures, the fiber was exposed to the equivalent of 1.9 % engineering strain at 1000°C, but measured only a 0.7 % engineering strain due to the poor strain transfer. Although compensating for the plastic behavior of Ni proved challenging, the bonding of a brittle silica fiber to a metal matrix surviving to 1000°C invites potential iterations on coating material for future application. For example, the embedded fiber is sufficient for acoustic energy transfer, realizing high temperature distributed acoustic sensing.

36 MATERIALS SCIENCE↗

NASA NTRS1989

Intrinsic fatigue crack propagation in aluminum-lithium alloys - The effect of gaseous environments

Gaseous environmental effects on intrinsic fatigue crack growth are significant for the Al-Li-Cu alloy 2090, peak aged. For both moderate Delta K-low R and low Delta K-high R regimes, crack growth rates decrease according to the environment order: purified water vapor, moist air, helium and oxygen. Gaseous environmental effects are pronounced near threshold and are not closure dominated. Here, embrittlement by low levels of H2O (ppm) supports hydrogen embrittlement and suggests that molecular transport controlled cracking, established for high Delta K-low R, is modified near threshold. Localized crack tip reaction sites or high R crack opening shape may enable the strong, environmental effect at low levels of Delta K. Similar crack growth in He and O2 eliminates the contribution of surface films to fatigue damage in alloy 2090. While 2090 and 7075 exhibit similar environmental trends, the Al-Li-Cu alloy is more resistant to intrinsic corrosion fatigue crack growth.

Piascik, Robert S.↗

DOE OSTI2021

Optimization of Magnesium‐Doped Lithium Metal Anode for High Performance Lithium Metal Batteries through Modeling and Experiment

Abstract Lithium (Li)‐magnesium (Mg) alloy with limited Mg amount, which can also be called Mg‐doped Li (Li‐Mg), has been considered as a potential alternative anode for high energy density rechargeable Li metal batteries. However, the optimum doping‐content of Mg in Li‐Mg anode and the mechanism of the improved performance are not well understood. Herein, density functional theory (DFT) calculations are used to investigate the effect of Mg amount in Li‐Mg anode. The Li‐Mg with about 5 wt. % Mg (abbreviated as Li‐Mg5) has the lowest absorption energy of Li, thus all the surface area can be “controlled” by Mg atoms, leading to the smooth and continuous deposition of Li on the surface around the Mg center. A localized high concentration electrolyte enables Li‐Mg5 to exhibit the best cycling stability in Li metal batteries with high‐loading cathode and lean electrolyte under 4.4 V high‐voltage, which is approaching the demand of practical application. This electrolyte also helps generate an inorganic‐rich solid electrolyte interphase, which leads to smooth, compact and less corrosion layer on the Li‐Mg5 surface. Both theoretical simulations and experimental results prove that Li‐Mg5 has optimum Mg content and gives best battery cycling performance.

Gao, Peiyuan↗

NASA NTRS1994

Cryogenic Hybrid Magnetic Bearing

Cryogenic hybrid magnetic bearing is example of class of magnetic bearings in which permanent magnets and electromagnets used to suspend shafts. Electromagnets provide active control of position of shaft. Bearing operates at temperatures from -320 degrees F (-196 degrees C) to 650 degrees F (343 degrees C); designed for possible use in rocket-engine turbopumps, where effects of cryogenic environment and fluid severely limit lubrication of conventional ball bearings. This and similar bearings also suitable for terrestrial rotating machinery; for example, gas-turbine engines, high-vacuum pumps, canned pumps, precise gimbals that suspend sensors, and pumps that handle corrosive or gritty fluids.

Meeks, Crawford R.↗

DOE OSTI2021

Formation of three-dimensional bicontinuous structures via molten salt dealloying studied in real-time by in situ synchrotron X-ray nano-tomography

Abstract Three-dimensional bicontinuous porous materials formed by dealloying contribute significantly to various applications including catalysis, sensor development and energy storage. This work studies a method of molten salt dealloying via real-time in situ synchrotron three-dimensional X-ray nano-tomography. Quantification of morphological parameters determined that long-range diffusion is the rate-determining step for the dealloying process. The subsequent coarsening rate was primarily surface diffusion controlled, with Rayleigh instability leading to ligament pinch-off and creating isolated bubbles in ligaments, while bulk diffusion leads to a slight densification. Chemical environments characterized by X-ray absorption near edge structure spectroscopic imaging show that molten salt dealloying prevents surface oxidation of the metal. In this work, gaining a fundamental mechanistic understanding of the molten salt dealloying process in forming porous structures provides a nontoxic, tunable dealloying technique and has important implications for molten salt corrosion processes, which is one of the major challenges in molten salt reactors and concentrated solar power plants.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Alkali cation-induced cathodic corrosion in Cu electrocatalysts

The reconstruction of Cu catalysts during electrochemical reduction of CO 2 is a widely known but poorly understood phenomenon. Herein, we examine the structural evolution of Cu nanocubes under CO 2 reduction reaction and its relevant reaction conditions using identical location transmission electron microscopy, cyclic voltammetry, in situ X-ray absorption fine structure spectroscopy and ab initio molecular dynamics simulation. Our results suggest that Cu catalysts reconstruct via a hitherto unexplored yet critical pathway - alkali cation-induced cathodic corrosion, when the electrode potential is more negative than an onset value (e.g., –0.4 V RHE when using 0.1 M KHCO 3 ). Having alkali cations in the electrolyte is critical for such a process. Consequently, Cu catalysts will inevitably undergo surface reconstructions during a typical process of CO 2 reduction reaction, resulting in dynamic catalyst morphologies. While having these reconstructions does not necessarily preclude stable electrocatalytic reactions, they will indeed prohibit long-term selectivity and activity enhancement by controlling the morphology of Cu pre-catalysts. Alternatively, by operating Cu catalysts at less negative potentials in the CO electrochemical reduction, we show that Cu nanocubes can provide a much more stable selectivity advantage over spherical Cu nanoparticles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1992

Mach 6 electroformed nickel nozzle refurbishment: FNAS investigation of ultra-smooth surfaces

The task objective has been to apply a coating of nickel-phosphorous alloy to a laminar flow wind tunnel nozzle by catalytic deposition and then polish and inspect the inside surface using optical device processes. The surface of the nozzle was coated with a nickel-phosphorous alloy of sufficient hardness and corrosion resistance to improve the durability. Due to plating defects that were clearly process related and not inherent, the final polished part was less than the desired quality. Surface finishing processes and lapping media were identified which produced a submicron surface finish on the interior plated surface. Defects apparently manifested by the first plating attempt were repaired using a small brush plating process demonstrating that individual small defects can be repaired. Measurement and analysis by profilometry demonstrated that quantitative control of the surface can be achieved.

Rood, Robert↗

DOE OSTI2021

Optimization of Magnesium-Doped Lithium Metal Anode for High Performance Lithium Metal Batteries through Modeling and Experiment

Lithium (Li)-magnesium (Mg) alloy with limited Mg amount, which can also be called Mg-doped Li (Li-Mg), has been considered as a potential alternative anode for high energy density rechargeable Li metal batteries. However, the optimum doping-content of Mg in Li-Mg anode and the mechanism of the improved performance are not well understood. In this study, density functional theory (DFT) calculations are used to investigate the effect of Mg amount in Li-Mg anode. The Li-Mg with about 5 wt. % Mg (abbreviated as Li-Mg5) has the lowest absorption energy of Li, thus all the surface area can be “controlled” by Mg atoms, leading to the smooth and continuous deposition of Li on the surface around the Mg center. A localized high concentration electrolyte enables Li-Mg5 to exhibit the best cycling stability in Li metal batteries with high-loading cathode and lean electrolyte under 4.4 V high-voltage, which is approaching the demand of practical application. This electrolyte also helps generate an inorganic-rich solid electrolyte interphase, which leads to smooth, compact and less corrosion layer on the Li-Mg5 surface. Both theoretical simulations and experimental results prove that Li-Mg5 has optimum Mg content and gives best battery cycling performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Fundamental chemical physics revealed by scattering reactive open-shell atoms from surfaces

The dynamics of reactive atoms at surfaces are centrally important to areas such as heterogeneous catalysis, corrosion, materials degradation in extreme environments, and plasma etching. Remarkably detailed understanding of dynamical processes at surfaces has been extracted from scattering molecules and inert atoms under well-defined conditions. However, traditional techniques for generating beams of reactive atoms often result in impure mixtures, broad energy distributions, and poorly defined contributions of metastable electronically excited atoms. In this perspective article, we review the state-of-the-art in reactive atom surface scattering with a focus on experiments performed under controlled conditions on well-defined surfaces. We highlight a new technique for controlled state-to-state scattering of polyelectronic atoms from surfaces, based on vacuum ultraviolet photolysis and state-selective ion imaging. The new capabilities provide an avenue for research into the underexplored area of excited state and spin selective chemical dynamics at surfaces.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2024

Development of Miniaturized High-Temperature Multi-Process Monitoring System

The main objective of this research program is to design, manufacture, and demonstrate a miniaturized, multi-process, monitoring system (mMPMS) for boiler condition management and easy system deployment to obtain a higher spatial resolution. This system will facilitate a Condition-Based Maintenance (CBM) philosophy that actively monitors the health of assets to predict and prevent failures and maximize availability and generating capacity at a reduced cost. CBM systems can provide boiler data that the advanced process control (APC) system can utilize for plant performance optimization, which is increasingly relevant as coal power plants shift from predominantly base-load operation to predominantly transient operation involving large load swings.

20 FOSSIL-FUELED POWER PLANTS↗