SEARCH · Engineering Papers

Results for “conceptual model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Propulsion simulator for magnetically suspended wind tunnel models

Simulation of propulsion induced aerodynamic forces and moments, which arise as a result of interactions between propulsive jets and the free stream, is one of the most desired capabilities in magnetic suspension wind tunnels. The feasibility of generating exhaust jets of appropriate characteristics onboard magnetically suspended models was examined. Four concepts of remotely operated propulsion simulators was considered. Three conceptual designs involving conventional technologies such as compressed gas cylinders, liquid monopropellants, and solid propellants were developed. The fourth concept, a laser assisted thruster, which can potentially simulate both inlet and exhaust flows, was found to require very high power levels. The measurement of aerodynamic forces and/or moments were demonstrated, including the effects of exhaust jets, in MSBS wind tunnels. Two propulsion simulator models were developed, a small scale and a large scale unit, both using compressed, liquified CO2 as propellant. Results of the wind tunnel tests with the small scale simulator are discussed.

Joshi, P. B.↗

NASA NTRS1993

Understanding land surface evapotranspiration with satellite multispectral measurements

Quantitative use of remote multispectral measurements to study and map land surface evapotranspiration has been a challenging issue for the past 20 years. Past work is reviewed against process physics. A simple two-layer combination-type model is used which is applicable to both vegetation and bare soil. The theoretic analysis is done to show which land surface properties are implicitly defined by such evaporation models and to assess whether they are measurable as a matter of principle. Conceptual implications of the spatial correlation of land surface properties, as observed by means of remote multispectral measurements, are illustrated with results of work done in arid zones. A normalization of spatial variability of land surface evaporation is proposed by defining a location-dependent potential evaporation and surface temperature range. Examples of the application of remote based estimates of evaporation to hydrological modeling studies in Egypt and Argentina are presented.

Menenti, M.↗

NASA NTRS1988

The structure of red-infrared scattergrams of semivegetated landscapes

A physically based linear stochastic geometric canopy soil reflectance model is presented for characterizing spatial variability of semivegetated landscapes at subpixel and regional scales. Landscapes are conceptualized as stochastic geometric surfaces, incorporating not only the variability in geometric elements, but also the variability in vegetation and soil background reflectance which can be important in some scenes. The model is used to investigate several possible mechanisms which contribute to the often observed characteristic triangular shape of red-infrared scattergrams of semivegetated landscapes. Scattergrams of simulated and semivegetated scenes are analyzed with respect to the scales of the satellite pixel and subpixel components. Analysis of actual aerial radiometric data of a pecan orchard is presented in comparison with ground observations as preliminary confirmation of the theoretical results.

Jasinski, Michael F.↗

NASA NTRS1989

The structure of red-infrared scattergrams of semivegetated landscapes

A physically based linear stochastic geometric canopy soil reflectance model is presented for characterizing spatial variability of semivegetated landscapes at subpixel and regional scales. Landscapes are conceptualized as stochastic geometric surfaces, incorporating not only the variability in geometric elements, but also the variability in vegetation and soil background reflectance which can be important in some scenes. The model is used to investigate several possible mechanisms which contribute to the often observed characteristic triangular shape of red-infrared scattergrams of semivegetated landscapes. Scattergrams of simulated semivegetated scenes are analyzed with respect to the scales of the satellite pixel and subpixel components. Analysis of actual aerial radiometric data of a pecan orchard is presented in comparison with ground observations as preliminary confirmation of the theoretical results.

Jasinski, Michael F.↗

NASA NTRS1973

Study and design of a cryogenic propellant acquisition system

The development of an acquisition system for supplying subcooled liquid hydrogen and liquid oxygen under in-orbit conditions is discussed. The system will be applied to the integrated cryogenic feed requirements for space systems such as a space shuttle cryogenic auxiliary propulsion system (APS) and main propulsion for an advanced spacecraft propulsion module (ASPM). Concepts that use the favorable surface tension characteristics of fine mesh screens are emphasized. The specific objectives of the program are: (1) to evolve conceptual designs for candidate acquisition systems, (2) to formulate the analytical models needed to analyze the systems, and (3) to generate parametric data on overall candidate system performance, characteristics, and operational features in sufficient depth to establish critical design problems and criteria to support a sound system design and evaluation.

Burge, G. W.↗

NASA NTRS1988

Conceptual design of a lunar oxygen pilot plant Lunar Base Systems Study (LBSS) task 4.2

The primary objective was to develop conceptual designs of two pilot plants to produce oxygen from lunar materials. A lunar pilot plant will be used to generate engineering data necessary to support an optimum design of a larger scale production plant. Lunar oxygen would be of primary value as spacecraft propellant oxidizer. In addition, lunar oxygen would be useful for servicing nonregenerative fuel cell power systems, providing requirements for life support, and to make up oxygen losses from leakage and airlock cycling. Thirteen different lunar oxygen production methods are described. Hydrogen reduction of ilmenite and extraction of solar-wind hydrogen from bulk lunar soil were selected for conceptual design studies. Trades and sensitivity analyses were performed with these models.

Source record↗

NASA NTRS1991

Designs for the ATDRSS tri-band reflector antenna

Two approaches to design a tri-band reflector antenna for the Advanced TDRSS are examined. Two reflector antenna configurations utilizing frequency selective surfaces for operation in three frequency bands, S, Ku, and Ka, are proposed. Far-field patterns and the antenna feed losses were computed for each configuration. An offset-fed single reflector antenna configuration was adapted for conceptual spacecraft design. CADAM drawings were completed and a 1/13th scale model of the spacecraft was constructed.

Lee, Shung-Wu↗

NASA NTRS1990

Cryogenic On-Orbit Liquid Depot Storage, Acquisition, and Transfer satellite (COLD-SAT) feasibility study

The Cryogenic On-Orbit Liquid Depot Storage, Acquisition, and Transfer Satellite (COLD-SAT) is an experimental spacecraft launched from an expendable launch vehicle which is designed to investigate the systems and technologies required for efficient, effective, and reliable management of cryogenic fluid in the reduced gravity space environment. The COLD-SAT program will provide the necessary data base and provide low-g proving of fluid and thermal models of cryogenic storage, transfer, and resupply concepts and processes. A conceptual approach was developed and an overview of the results of the 24 month COLD-SAT Phase A feasibility is described which includes: (1) a definition of the technology needs and the accompanying experimental 3 month baseline mission; (2) a description of the experiment subsystem, major features and rationale for satisfaction of primary and secondary experiment requirements using liquid hydrogen as the test fluid; and (3) a presentation of the conceptual design of the COLD-SAT spacecraft subsystems which support the on-orbit experiment with emphasis on areas of greatest challenge.

Bailey, William J.↗

NASA NTRS1995

A numerical model for dynamic wave rotor analysis

A numerical model has been developed which can predict the dynamic (and steady state) performance of a wave rotor, given the geometry and time dependent boundary conditions. The one-dimensional, perfect gas, CFD based code tracks the gasdynamics in each of the wave rotor passages as they rotate past the various ducts. The model can operate both on and off-design, allowing dynamic behavior to be studied throughout the operating range of the wave rotor. The model accounts for several major loss mechanisms including finite passage opening time, fluid friction, heat transfer to and from the passage walls, and leakage to and from the passage ends. In addition, it can calculate the amount of work transferred to and from the fluid when the flow in the ducts is not aligned with the passages such as occurs in off-design operation. Since it is one-dimensional, the model runs reasonably fast on a typical workstation. This paper will describe the model and present the results of some transient calculations for a conceptual four port wave rotor designed as a topping cycle for a small gas turbine engine.

Paxson, D. E.↗

NASA NTRS1993

Solid Modeling Aerospace Research Tool (SMART) user's guide, version 2.0

The Solid Modeling Aerospace Research Tool (SMART) software package is used in the conceptual design of aerospace vehicles. It provides a highly interactive and dynamic capability for generating geometries with Bezier cubic patches. Features include automatic generation of commonly used aerospace constructs (e.g., wings and multilobed tanks); cross-section skinning; wireframe and shaded presentation; area, volume, inertia, and center-of-gravity calculations; and interfaces to various aerodynamic and structural analysis programs. A comprehensive description of SMART and how to use it is provided.

Mcmillin, Mark L.↗

NASA NTRS1998

Technical Characteristics of a Novel Helical-Groove Traveling-Wave Tube Structure

Experimental measurements of the dispersion characteristics of a C-band helix structure were carried out and compared to the dispersion characteristics found from a helix model using the three-dimensional electromagnetic computer code MAFIA. A conceptually novel design comprising a helical thread of the same pitch and inner diameter in a cylindrical waveguide also were calculated using the MAFIA code. The helical-groove structure exhibits a smaller bandwidth but at a much higher frequency range than the traditional helical structure for similar physical dimensions. It is physically more robust in construction. The interaction impedance also compares favorably with those of the conventional structure.

Wallett, Thomas M.↗

NASA NTRS2010

Preliminary Characterization of the Altair Lunar Lander Slosh Dynamics and Some Implications for the Thrust Vector Control Design

This paper describes a conceptual design of the Thrust Vector Control (TVC) system and preliminary modeling of propellant slosh, for the Altair Lunar Lander. Altair is a vehicle element of the NASA Constellation Program aimed at returning humans to the moon. Guidance, Navigation, and Control (GN&C) is the measurement and control of spacecraft position, velocity, and attitude in support of mission objectives. One key GN&C function is the commanding of effectors that control attitude and impart delta V on the vehicle, utilizing both reaction control system (RCS) thrusters and throttling and TVC gimbaling of the vehicle main engine. Both the Altair descent and ascent modules carry fuel tanks. During thrusting maneuvers, the sloshing of liquid fuels in partially filled tanks can interact with the controlled system in such a way as to cause the overall system to be unstable. These fuel tanks must be properly placed, relative to the spacecraft's c.m., to avoid any unstable interactions. Following this will be a discussion of propellant slosh modeling work performed for the present vehicle configuration, including slosh frequency and participatory fluid mass predictions. Knowing the range of slosh mode frequencies over mission phases, the TVC bandwidth must be carefully selected so as not to excite the slosh modes at those frequencies. The likely need to increase the damping factor of slosh modes via baffles will also be discussed. To conclude, a discussion of operations procedures aimed at minimizing TVC-slosh interactions will be given.

Lee, Allan Y.↗

NASA NTRS2019

Orbital Debris Ontology, Terminology, and Knowledge Modeling

The looming threat orbital debris poses to assets in orbit demands solutions. As the orbital population grows, so does this hazard, but so does the sea of data. The problem is also an opportunity for interdisciplinary innovation and cooperation. This paper focuses on the data and information management aspect of developing solutions for a sustainable and safe orbital space environment. The corresponding author’s in-progress work to develop an orbital debris domain ontology is summarized in order to discuss knowledge modeling for this domain. Methodological approaches of this effort can also contribute to standards efforts and address terminological and policy questions. Leveraging the growing volumes of orbital debris and space situational awareness (SSA) data will create a more complete picture of the orbital space environment. Part of the solution will be: consistent and correct data interpretation, sharing orbital debris and SSA data in one form or another, terminology development & harmonization, and knowledge or domain modeling. To facilitate this, [Rovetto, 2015/16] discussed ontology development for the orbital debris domain. This paper lists concepts from that paper, and subsequently developed concepts [2-9]. Ontology engineering is an interdisciplinary field related to knowledge representation and reasoning in artificial intelligence, semantic technologies and the so-called semantic web. An ontology is effectively a computable and semantically rich terminology that presents a knowledge or domain model for a topic area. Expressions of knowledge or assertions are stored using formally defined term. This knowledge base is reasoned over to yield answers to queries, among other things. Ontologies have been developed in knowledge-based projects across various disciplines, and used for such things as search engines, chatbots, enterprise knowledge graphs, etc. Ontologies support: interoperability, automated reasoning, data sharing and integration, data search and retrieval, and communicating the meaning of data. The Orbital Debris Ontology (ODO), and related ontologies [Rovetto & Kelso 2016] [Rovetto 2016, 2017], were proposed to help achieve this. ODO, for instance, is intended as a domain ontology that can be used across federated databases, offering an explicitly specified set of concepts describing the orbital debris domain. Its meaning-rich taxonomy will provide a sharable semantics for orbital debris data to, in part, consistently communicate the meaning of data to both humans and machines, and tag data elements in space object catalogs to help afford inference tasks, decision support, knowledge discovery, and information integration. ODO and the SSA ontology (SSAO) is part of the overall Orbital Space Domain Ontology concept, which is conceived as a broader domain reference ontology. It aims to provide a knowledge representation structure of the orbital space environment, a common semantic model, and develop a sharable terminology. Collectively this will provide common meaning for datasets, a high-level taxonomy or classification for orbital space objects, and thus means to characterize space objects. Ongoing efforts have included using visualizations, R, JSON-LD, and contemporary semantic technologies. Potential applications and interdisciplinary partnerships include web-based platforms, web apps, visualizations, and academia projects. Community input and participation may yield a more widely understood domain model as well as facilitate terminological standards. For example, the proposed conceptual, terminological and ontological analysis may contribute to such efforts as the Space Debris Mitigation Requirements in the International Standards Organization by developing more precise, consistent and coherent terms and definitions. Projects that seek to develop in-house ontologies can use ODO and related ontologies as domain reference ontologies. This paper was developed independent of author affiliations. Readers are encouraged to contact corresponding author(1) with general interest and potential opportunities to support or realize the described project.

Robert J. Rovetto↗

NASA NTRSDate not supplied

Wind-Optimal Trajectories for Multirotor eVTOL Aircraft on UAM Missions

Distributed electric propulsion powered electric vertical takeoff and landing aircraft are expected to enable urban air mobility. Low specific energy of onboard lithium-ion polymer batteries and wind conditions impose constraints on flight endurance. Therefore, from the safety and efficiency perspective, planning and flying minimum energy trajectories are important.The primary motivation for this paper is to determine if there is an operational benefit to flying wind-optimal trajectories for short flights (less than 60 miles) in the urban environment. This study employs wind-optimal trajectories for a NASA-proposed conceptual multirotor aircraft flight in the urban environment. The optimal control model presented includes a wind model for quantifying the effect of wind on the trajectory. The optimal control problem is numerically solved using the direct method. Energy consumption and flight duration flying wind-optimal trajectories between origins and destinations in a metropolitan area are compared with energy consumption and flight duration flying on the great-circle paths between the same origin and destination pairs to determine the operational benefit of wind-optimal routing for short flights.The flight duration results for different scenarios are validated using a simulation tool designed and developed by NASA for exploring advanced air traffic management concepts. In summary,this research study suggests that for short flights in an urban environment, the wind-optimal trajectories have a very slight (insignificant) operational advantage over the great-circle trajectories in terms of energy consumption and flight duration. As expected, headwinds and tailwinds along the route of flight have a significant impact on energy consumption and flight duration.

Urban Air Mobility↗

NASA NTRS2018

Using Maxwell's Demon to Tame the "Devil in the Details" that are Encountered During System Development

Model-Based Systems Engineering (MBSE) is the formalized application of modeling to support system requirements, design, analysis, verification and validation activities beginning in the conceptual design phase and continuing throughout development and later life cycle phases . This presentation will discuss the value proposition that MBSE has for Systems Engineering, and the associated culture change needed to adopt it.

Model Based Systems Engineering↗

NASA NTRS2016

Application of Design of Experiments and Surrogate Modeling within the NASA Advanced Concepts Office, Earth-to-Orbit Design Process

Decisions made during early conceptual design have a large impact upon the expected life-cycle cost (LCC) of a new program. It is widely accepted that up to 80% of such cost is committed during these early design phases [1]. Therefore, to help minimize LCC, decisions made during conceptual design must be based upon as much information as possible. To aid in the decision making for new launch vehicle programs, the Advanced Concepts Office (ACO) at NASA Marshall Space Flight Center (MSFC) provides rapid turnaround pre-phase A and phase A concept definition studies. The ACO team utilizes a proven set of tools to provide customers with a full vehicle mass breakdown to tertiary subsystems, preliminary structural sizing based upon worst-case flight loads, and trajectory optimization to quantify integrated vehicle performance for a given mission [2]. Although the team provides rapid turnaround for single vehicle concepts, the scope of the trade space can be limited due to analyst availability and the manpower requirements for manual execution of the analysis tools. In order to enable exploration of a broader design space, the ACO team has implemented an advanced design methods (ADM) based approach. This approach applies the concepts of design of experiments (DOE) and surrogate modeling to more exhaustively explore the trade space and provide the customer with additional design information to inform decision making. This paper will first discuss the automation of the ACO tool set, which represents a majority of the development effort. In order to fit a surrogate model within tolerable error bounds a number of DOE cases are needed. This number will scale with the number of variable parameters desired and the complexity of the system's response to those variables. For all but the smallest design spaces, the number of cases required cannot be produced within an acceptable timeframe using a manual process. Therefore, automation of the tools was a key enabler for the successful application of an ADM approach to an ACO design study. Following the overview of the tool set automation, an example problem will be given to illustrate the implementation of the ADM approach. The example problem will first cover the inclusion of ground rules and assumptions (GR&A) for a study. The GR&A are very important to the study as they determine the constraints within which a trade study can be conducted. These trades must ultimately reconcile with the customer's desired output and any anticipated "what if" questions.

Zwack, Mathew R.↗

NASA NTRS2012

Improved Aerodynamic Analysis for Hybrid Wing Body Conceptual Design Optimization

This paper provides an overview of ongoing efforts to develop, evaluate, and validate different tools for improved aerodynamic modeling and systems analysis of Hybrid Wing Body (HWB) aircraft configurations. Results are being presented for the evaluation of different aerodynamic tools including panel methods, enhanced panel methods with viscous drag prediction, and computational fluid dynamics. Emphasis is placed on proper prediction of aerodynamic loads for structural sizing as well as viscous drag prediction to develop drag polars for HWB conceptual design optimization. Data from transonic wind tunnel tests at the Arnold Engineering Development Center s 16-Foot Transonic Tunnel was used as a reference data set in order to evaluate the accuracy of the aerodynamic tools. Triangularized surface data and Vehicle Sketch Pad (VSP) models of an X-48B 2% scale wind tunnel model were used to generate input and model files for the different analysis tools. In support of ongoing HWB scaling studies within the NASA Environmentally Responsible Aviation (ERA) program, an improved finite element based structural analysis and weight estimation tool for HWB center bodies is currently under development. Aerodynamic results from these analyses are used to provide additional aerodynamic validation data.

Gern, Frank H.↗

NASA NTRS1973

Qualitative investigation of booster recovery in open sea

Limited tests were conducted using 1/27 scale model of a Titan 3C booster plus 1/32.9 and 1/15.6 scale models of a solid rocket booster case to establish some of the characteristics that will effect recovery operations in open seas. This preliminary effort was designed to provide additional background information for conceptual development of a waterborne recovery system for space shuttle boosters, pending initiation of comprehensive studies. The models were not instrumented; therefore, all data are qualitative (approximations) and are based on observations plus photographic coverage.

Beck, P. E.↗