Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “composition and microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

An innovative and alternative approach toward gear fabrication

In this paper, we present the first demonstration of single-step gear manufacturing via an innovative in-situ friction stir forging approach. This novel process is a natural extension to the friction stir processing technique and relies on shear and normal stresses to form the complex shapes. Friction stir welding pin tool with shoulder is plunged at high revolutions per minute (rpm) into the sample to heat it to the desired temperature and enable plastic flow. Then, the tool is forged at high plunge rate to form the desired structurally-sound and defect free complex shapes. To better visualize the process the experiments are complemented by a 3D thermomechanically coupled, smoothed particle hydrodynamics (SPH) model to understand the material flow pattern both radially and through thickness in the gear teeth, plastic strain distribution, and temperature profile. We have demonstrated application of I-FSF to inherently poor formable AZ31 Mg, AA 7075-T6, and AA5083–10 vol% TiB 2 composite and fabricated 14-tooth spur gears from these materials with minimal farther machining. In conclusion, microstructure of the forged gears exhibited a directional material flow pattern due to the normal forging action and refinement of grains to 6–13 μm through dynamically recrystallization across the radial, through-thickness direction, which is in good agreement with the corresponding SPH simulation results.

42 ENGINEERING↗
DOE OSTI2023

Composition-dependent fracture energy in metallic glasses

The interplay between metallic glasses (MGs) mechanical properties, fracture energy (G), and glass-forming ability (GFA) and their dependence on alloy composition remain poorly understood. Here, we perform molecular dynamics simulations to investigate the intrinsic composition-dependence of G in Cu x Zr 100-x MGs (x = 20, 30, 40, 50, 64). The results indicate that the value of G increases with Cu content. In addition, it is revealed that MGs with higher G values display higher Poisson’s ratio (ν) and GFA, suggesting a close correlation between fracture toughness, mechanical properties, and GFA. This correlation between G, ν and GFA can be understood based on the fragility (m) of supercooled liquids, which is directly related to the structural heterogeneity in MGs. Larger m values are related to dynamic slowdown and supercooled liquid stabilization, which enhance GFA and the formation of pronounced structural heterogeneity, comprised of loosely packed regions that favor β-relaxation and the activation of shear transformation zones. Those concurrently promote the expansion of the plastic zone at the crack tip, enhancing the observed value of G. Furthermore, these simulation results shed light on the intrinsic relationship between fracture toughness, mechanical properties, and alloy composition in MGs.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Impact of Molten Gallium on the Microstructure and Corrosion Behavior of Aluminum and Uranium-Aluminum Alloys for Used Nuclear Fuel Reprocessing

Test reactors around the world utilize highly enriched uranium fuel to achieve high neutron fluxes for materials testing. Once spent, the remaining uranium is a valuable resource for subsequent fuel fabrication. However, some of these test reactor cores consist of curved plate-type fuel elements, fabricated using aluminum alloy 6061 (AA6061) cladding to encapsulate a uranium-aluminum alloy (UAlx) fuel matrix. These assemblies require non-standard reprocessing approaches for uranium recovery, as aluminum dissolves readily in acidic solutions, generating large volumes of waste and complicating downstream chemical separations. In this work, we investigate a novel chemical decladding strategy based on the interaction between AA6061/UAlx and molten gallium (Ga). Ga is known to induce severe degradation of aluminum metal through liquid metal embrittlement (LME), even at relatively low Ga concentrations. By penetrating the aluminum crystal lattice, Ga disrupts grain cohesion and facilitates fracture or dissolution of the aluminum matrix. Thermodynamic analysis of the Al–Ga binary phase diagram suggests that Ga may offer a viable pathway to selectively weaken or dissolve the AA6061 cladding, and potentially the aluminum component of the UAlx fuel matrix within. To this end, parametric experiments were performed at 50 °C and 100 °C across a range of Al–Ga atomic fractions. At lower Al fractions, the AA6061 was completely molten after 2 hours of exposure to the Ga metal. In contrast, samples with higher Al fractions (0.9 Al, 0.1 Ga) contained residual solids after 2 hours, which were characterized by microstructural examination using electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). These Al-Ga compositions were also evaluated using FactSage thermodynamic modeling to further elucidate the relationship between phase diagram behavior and LME.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Effect of 3D printing conditions on the micro- and macrostructure and properties of high-performance thermoplastic composites

Within the scope of extrusion based additive manufacturing, this chapter provides a review of the research in understanding the physical relationships between microstructure variables and macrostructure properties of high-performance thermoplastic polymers. The development of interlayer strength has been discussed based on the theory of inter-diffusion and re-entanglement of polymer chains at interface. The observations from the study in joining and direct-bonding of polymer surfaces provide insights into the mechanisms of the formation of interface between adjacent layers. Quantitative prediction of interfacial strength as a function of processing temperature and contact time is presented. The mechanisms that lead to reduced mechanical strength at the interface are discussed. The second half of the chapter outlined a set of printing conditions and their influence on structural properties.

Liu, Peng↗
DOE OSTI2020

Scaling Up metal additive manufacturing process to fabricate molds for composite manufacturing

Direct Energy Deposition (DED) systems are currently used to repair and maintain existing parts in the aerospace and automotive industries. This paper discusses an effort to scale up the DED technique in order to Additively Manufacture (AM) molds and dies used in the composite manufacturing industry. The US molds and dies market has been in a rapid decline over the last decade due to outsourcing to non-US entities. Oak Ridge National Laboratory (ORNL), Wolf Robotics and Lincoln Electric have developed a Metal Big Area Additive Manufacturing (MBAAM) system that uses a high deposition rate and a low-cost wire feedstock material. In this work we used the MBAAM system with a mild steel wire, ER70S-6, to fabricate a compression molding mold for composite structures used in automotive and mass-transit applications. In addition, the mechanical properties of the AM structure were investigated, and it was found that the MBAAM process delivers parts with high planar isotropic behavior. The paper investigates the microstructure and grain of the printed articles to confirm the roots of the observed planar isotropic properties. Here, the manufactured AM mold was used to fabricate 50 composite parts with no observed mold deformations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructure Alignment Effects from Engineered Cooling during Additive Manufacturing of Alnico Magnets from Prealloyed Powder

Alnico is a rare-earth free; permanent magnet (PM) which maintains its saturation magnetization while at temperatures up to 550°C but lacks the coercivity and energy product needed for a wide range of demanding applications. With an optimal set of processing and manufacturing techniques, Alnico could replace Dy-free Nd-Fe-B magnets in certain applications if the microstructure is textured in a $\langle$001$\rangle$ direction. Additive manufacturing (AM) of near-net-shape magnets may provide such texture. To investigate the possibility, directed-energy deposition (DED) in conjunction with an actively cooled substrate was used to build samples with a compositionally modified, gas-atomized, Alnico 8 alloy. The resulting samples were solutionized and quenched, followed by magnetic annealing and a heat treatment. Magnetic properties and microstructures are compared to previous work.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ultra–high molecular weight polyethylene micro–ribbon fibers gel spun using orange terpenes

Toxic, hazardous petrochemical solvents are commonly used for industrial-scale ultra-high molecular weight polyethylene (UHMWPE) fiber production, but orange terpenes, a byproduct of orange fruit production, present a bio-derived, sustainable alternative. In this work, fine UHMWPE fibers were spun using orange terpenes as the spin solvent, hot-drawn at a draw ratio of 5:1, investigated for their morphology, microstructure, and thermal and mechanical properties. The resulting fibers exhibited a flat, micro-ribbon cross-section, which is highly desirable for achieving high fiber volume fractions in UHMWPE-fiber reinforced composites. After drawing, the fibers possessed 4× greater breaking tenacity than any previously published studies on UHMWPE fibers spun using orange terpenes with a tenacity of 8.6 cN/dtex and tensile modulus of 229.2 cN/dtex. Microstructural analysis via differential scanning calorimetry and X-ray diffraction revealed that the hot drawing process significantly increased molecular orientation, but crystallinity decreased due to crystallite melting during drawing. Therefore, the mechanical properties of these fibers may be significantly improved with optimization of the fiber drawing process. As a work, this work establishes the strong potential of orange terpenes as an environmentally-friendly alternative solvent for UHMWPE gel spinning and sets a foundation for future parametric optimization of the spinning and drawing of these fibers.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Evaluating Fracture Behavior of Bioinspired Alumina-YSZ Composites through Static and Dynamic Mechanical Testing

Ceramic materials are known for their high hardness and strength but are limited by low toughness and sudden failure. Inspired by the microstructure of dental enamel, which features undulating rods that promote crack deflection and energy absorption, architected specimens were designed and manufactured. A bespoke ball-on-ring (BoR) testing apparatus measured the static biaxial rupture strength of these bioinspired materials. Additionally, impact testing with spherical steel projectiles assessed their behavior under dynamic conditions. Monolithic alumina specimens were compared to architected alumina reinforced with yttria-stabilized zirconia (YSZ) rods produced via direct ink write 3D printing. BoR tests revealed that monolithic alumina had a Weibull modulus of 10.53 and a characteristic strength of 372.3 MPa, while the composite specimens showed a Weibull modulus of 5.46 and a characteristic strength of 213.3 MPa. Although the composite failed at lower stresses and projectile velocities, it exhibited notable crack deflection and fracture resistance, with cracks being effectively interrupted by the rod inclusions. The composite specimens also resulted in fewer and larger fragments upon impact. Finite element simulations confirmed the effectiveness of the rod structures in enhancing fracture resistance.

Bioinspired materials↗
DOE OSTI2021

Tailoring plasticity mechanisms in compositionally graded hierarchical steels fabricated using additive manufacturing

Abstract While there exists in nature abundant examples of materials with site-specific gradients in microstructures and properties, engineers and designers have traditionally used monolithic materials with discrete properties. Now, however, additive manufacturing (AM) offers the possibility of creating structures that mimic some aspects of nature. One example that has attracted attention in the recent years is the hierarchical structure in bamboo. The hierarchical architecture in bamboo is characterized by spatial gradients in properties and microstructures and is well suited to accommodate and survive complex stress states, severe mechanical forces, and large deformations. While AM has been used routinely to fabricate functionally graded materials, this study distinguishes itself by leveraging AM and physical metallurgy concepts to trigger cascading deformation in a single sample. Specifically, we have been successful in using AM to fabricate steel with unique spatial hierarchies in structure and property to emulate the structure and deformation mechanisms in natural materials. This study shows an improvement in the strength and ductility of the nature-inspired “hierarchical steel” compared with conventional cast stainless steels. In situ characterization proves that this improvement is due to the sequential activation of multiple deformation mechanisms namely twinning, transformation-induced plasticity, and dislocation-based plasticity. While significantly higher strengths can be achieved by refining the chemical and processing technique, this study sets the stage to achieve the paradigm of using AM to fabricate structures which emulate the flexibility in mechanical properties of natural materials and are able to adapt to in-service conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Layered oxide cathode-inspired secondary hard carbon microsphere anode material for high-power and long-life rechargeable batteries

A new anode material that will provide lithium ion (Li-ion) batteries with high energy and power density is urgently needed. In this work, a layered oxide cathode-inspired secondary hard carbon microsphere (CMS) anode material was designed, and exhibited excellent rate performance and long cyclability. Polyacrylonitrile/poly(styrene-co-acrylonitrile) (PAN/SAN) compositions displaying the meatball-like shape of the PAN precursor were carbonized into CMSs having turbostratic microstructures. The CMS carbonized at 1,000°C (CMS1000) displayed high specific capacity at the highest current density of 1,000mAg -1 , i.e., 77.6 % of its average charge capacity at 100 mA g -1 , and considerable cycling retention after 500 cycles, i.e., 83.8 % of the specific capacity at cycle 25. In conclusion, our work demonstrates that the design of new anode materials is a fruitful route to improve commercial Li-ion batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Interplay between element-specific distortions and electrocatalytic oxygen evolution for cobalt–iron hydroxides

A microscopic understanding of how Fe-doping of Co(OH) 2 improves electrocatalytic oxygen evolution remains elusive. We study two Co 1–x Fex(OH) 2 series that differ in fabrication protocol and find composition alone poorly correlates to catalyst performance. Structural descriptors extracted using X-ray diffraction, X-ray absorption spectroscopy, and Raman spectroscopy reveal element-specific distortions in Co 1–x Fe x (OH) 2 . These structural descriptors are composition-dependent within individual sample series but inconsistent across fabrication protocols, revealing fabrication-dependence in catalyst microstructure. Correlations between structural parameters from different techniques show that Fe–O resists bond length changes, forcing distortion of Co environments. We find the difference in O–M–O bond angles between Co and Fe sites to correlate with electrocatalytic behavior across both sample series, which we attribute to asymmetric distortion of potential energy surfaces for the Co(III) to Co(IV) oxidation. A Tafel slope consistent with a rate-limiting step without electron transfer emerges as the O–Co–O angle decreases, implying a distortion-induced transition in the rate-limiting step. The fabrication dependence of electronic and bonding structure in the catalysts should be considered in theoretical and high-throughput analyses of electrocatalyst materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Microstructure, electrical resistivity, and tensile properties of neutron-irradiated Cu–Cr–Nb–Zr

High strength, high conductivity copper alloys that can resist creep at high temperatures are one of the primary candidates for efficient heat exchangers in fusion reactors. Cu–Cr–Nb–Zr (CCNZ) alloys, which were designed to improve the strength and creep life of ITER Cu–Cr–Zr (CCZ) reference alloys, have been found to have comparable electrical conductivity and tensile properties to CCZ alloys. The measured creep rupture times for these improved alloys is about ten times higher than the ITER reference alloys at 90–125 MPa at 500 °C. However, the effects of neutron irradiation on these alloys, and the ensuing material properties, have not been studied; thus, their utility in a fusion reactor environment is not well understood. This study characterizes the room temperature mechanical and electrical properties of a neutron-irradiated CCNZ alloy and compares them to a neutron-irradiated ITER reference heat sink CCZ alloy. Tensile specimens were neutron irradiated in the High Flux Isotope Reactor (HFIR) to 5 dpa between 250 °C and 325 °C. Post-irradiation characterization included electrical resistivity measurements, hardness, and tensile tests. Microstructural evaluation used scanning electron microscopy, energy dispersive x-ray spectroscopy, and atom probe tomography to characterize the irradiation-produced changes in the microstructure and investigate the mechanistic processes leading to post-irradiation properties. Transmutation calculations were validated with composition measurements from atom probe data and used to calculate contributions to the increased electrical resistivity measured after irradiation. Comparisons with CCZ alloys in the same irradiation heat found that the post-irradiated CCNZ and CCZ alloys had comparable electrical resistivity. Although CCNZ alloys suffered more irradiation hardening than CCZ, the overall tensile behavior deviated very little from non-irradiated values in the temperature range studied.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Operating Stresses and Their Effects on Degradation of LSM-Based SOFC Cathodes

The performance of solid oxides fuel cells (SOFCs) with four different Mn excess of lanthanum strontium manganite (LSM) -based cathodes were examined under different temperatures (1,000 °C, 900 °C), current densities (0, 380, and 760 mA cm -2 ), and cathode atmospheres (p O 2 )=0.1,0.15,0.21) for durations ranging from 58 to 1,008 h. Each yttria-stabilized zirconia (YSZ) electrolyte-supported “button” cell had a porous Ni/YSZ composite anode and a porous LSM/YSZ composite cathode. The cells’ output voltage versus time were recorded and electrochemical impedance spectroscopy (EIS) and linear sweep voltammetry (LSV) measurements were performed every 24 hours. The total area specific resistance (ASR) was calculated from these measurements. The values of ASR from both EIS and LSV were comparable between each other but lower than that from durability test. Distribution of relaxation times (DRT) analysis was performed to investigate the electrochemical processes and their corresponding relaxation frequencies as well as their attributions to the total ASR. The series resistance and parallel resistance that obtained from the equivalent circuit fit of the Nyquist plot were higher at low temperature and low p O 2 regardless of LSM compositions. The area of the peaks derived from DRT analysis increased with time during individual tests. The microstructures of the tested cells were examined using scanning electron microscopy and energy-dispersive x-ray spectroscopy (SEM/EDS). Manganese oxide particles were observed near the cathode-electrolyte interface after prolonged (1,008 h) testing in air of a cell with LSM of 11% manganese excess, and after a short test (58 h) under low oxygen (p O 2 = 0.10) in a cell with LSM of 5% manganese excess. However, the role of MnOx in cell degradation is still unknown.

08 HYDROGEN↗
DOE OSTI2021

Structural and magnetic properties of hard magnetic system Ce(Co 1 -Fe ) 4.4 Cu 0.6 (0 ≤ x ≤ 0.19)

The Ce(Co 1 -Fe ) 4.4 Cu 0.6 (0 ≤ x ≤ 0.19) is a composite, hard magnetic system that is based on the CaCu 5 -type structure (1:5). It shows both, unique magnetic and microstructural features that are essential for permanent magnets, e.g., exceptional squareness of the 2nd. quadrant of the magnetization loops and microstructural features typically needed for pinning. Samples solidified in alumina crucibles are coarse-grained and often clearly faceted and readily align in a magnetic field. X-ray, SEM, and TEM analyses show a 1:5-type single-phase material when quenched from high temperature, which, after heat treatment, transforms into a laminar coherent nanostructure through the formation of a dense array of extended intercalated regions. Furthermore, these extended intercalated regions are comprised of segments of the Ce 2 Ni 7 –type structure (2:7) which segregate into various closely related precipitates forming a nanostructure similar to the SmCo 5 - Sm 2 Co 17 composites seen in Sm-Co permanent magnets. Based on TEM and Lorentz microscopy of well-aligned single grain particles, the magnetic domains’ reversal mechanism is regulated by anisotropy fluctuations occurring along the easy direction of magnetization and strong exchange interactions between the matrix and defects (e.g.: stacking faults). Lorentz microscopy suggests the domain wall is not physically pinned by the defect, but rather is offset/deflected when it interacts with the defect. The Lorentz and magnetization data suggest that defects cause a bending of the moment away from the c axis inside the grains.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure homogenization of concrete used in nuclear power plants

Almost all nuclear power plants in the United States are operating past their intended lifetimes or are requesting lifetime extensions. Therefore, understanding changes to the concrete containment structure over time is crucial to evaluate the structure’s continued viability. Concrete materials are heterogeneous particulate composites that exhibit viscoelastic material properties, which can lead to slow deformation over time, causing stress redistribution and the potential for creep cracking. A code to generate random, three dimensional (3D) concrete microstructures has been developed and paired with finite element analysis to predict the long-term viscoelastic properties of concrete. Data from these simulations are used to develop constitutive equations for the viscoelastic behavior of the homogenized concrete. The codes in this work are used to virtualize laboratory experiments, to obtain long-term creep data in a faster, cheaper manner. To validate this work, the simulated creep behavior of concrete is compared to 800 d of experimental data that has been extended to 27 y of data using the Time-Temperature superposition (TTS) principal. Excellent agreement between the simulation results and experimental data is seen.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Microstructure, Transport, and Mechanics of Compacted Clay Simulated at the 0.1 μm Scale (1400 Smectite Clay Particles) Using a Coarse-Grained Model with Explicit Counterions

Clay-rich geomaterials play a critical role in many subsurface systems. The macroscale properties of these materials (low permeability, high ionic conductivity, high swelling pressure, etc.) are sensitive to molecular-level adsorption and hydration interactions at clay−water interfaces. Efforts to develop multiscale simulation approaches to predict these properties reveal a scale gap between atomistic simulations (typically limited to systems smaller than 10 nm) and continuum-scale models (which use computational grid elements with dimensions ≳ 10 μm). In this study, we present a coarse-grained (CG) framework that partly bridges this gap by simulating compacted smectite clay assemblages with dimensions of 0.1 μm containing 1,400 clay particles across a range of dry densities (1,050 to 1,850 kg·m −3 ) and Na/Ca counterion compositions (Na fraction ranging from 0.2 to 1). The simulated systems, along with their reconstructed binary three-dimensional pore networks, are used to evaluate the microstructure, pore size distribution, tortuosity, ion diffusivity, and swelling pressure of compacted smectite clay. Results show that our approach captures important features of the mesoscale heterogeneity of compacted clays, including tactoid formation, hierarchical porosity, and anisotropic pore networks. Results also reveal how compaction and counterion composition govern emergent behaviors, including dominant pore sizes, directional transport, and electrochemical response. This work highlights the potential of CG simulations to bridge molecular and continuum scales and to advance geotechnical and environmental applications involving clay-rich materials as well as related nanoporous media such as geopolymers and calcium-silicate-hydrate. However, the results also suggest that accurate prediction of certain microstructural and mechanical properties (e.g., swelling pressure) may require even larger-scale systems on the order of 1 μm.

02 PETROLEUM↗
DOE OSTI2022

Microstructural Characterization of the Second High Fluence Baffle-Former Bolt Retrieved from a Westinghouse Two-loop Downflow Type PWR

As one of the pressurized water reactor (PWR) internal components, baffle-former bolts (BFBs) are subjected to significant mechanical stress and neutron irradiation from the reactor core during the plant operation. Over the long operation period, these conditions lead to potential degradation and reduced load-carrying capacity of the bolts. In support of evaluating long-term operational performance of materials used in core internal components, the Oak Ridge National Laboratory (ORNL), through the Department of Energy (DOE), Light Water Reactor Sustainability (LWRS) Program, Materials Research Pathway (MRP) has harvested two high fluence BFBs from a commercial Westinghouse two-loop downflow type PWR. The two bolts of interest, i.e. bolts # 4412 and 4416, were withdrawn from service in 2011 as part of a preventative replacement plan. No identification of cracking or potential damage was found for these bolts during their removal in 2011. However, the bolts required a lower torque for removal from the baffle structure than the original torque specified during installation. Irradiation displacement damage levels in the bolts range from 15 to 41 displacements per atom. The goal of this project is to perform detailed microstructural and mechanical property characterization of BFBs following in-service exposures. The information from these bolts will be integral to the LWRS program initiatives in evaluating end of life microstructure and properties. Furthermore, valuable data will be obtained that can be incorporated into model predictions of long-term irradiation behavior and compared to results obtained in high flux experimental reactor conditions. In this report, we present our latest study in FY22 on microstructural characterizations of the second high fluence baffle-former bolt, i.e., bolt # 4412. Analytical electron microscopy and atom probe tomography characterization were performed. The radiation-induced defects in the material add to the large wealth of knowledge for neutron-induced defects in 304/316 grades of stainless steels, specifically for radiation-induced precipitation after high fluence commercial PWR irradiation. The main findings are summarized as follows: 1) The cavity size was considerably larger in the bolt thread section than in the bolt head, with the bolt thread section having a bimodal distribution of cavities greater than ~6 nm in diameter and less than ~3 nm in diameter. The bolt head only had the small-sized cavities. In addition, there was a denuded zone of large cavities near grain boundaries in the thread section of the bolt. 2) Radiation-induced precipitation in the BFB #4412 was highly complex, with the volume fraction, size, and number density of Ni/Si and Cu-rich precipitates depending strongly on the radiation temperature/dose. In many cases, co-precipitates of adjoined clusters were found with Ni/Si-rich precipitates sandwiched between Cu-rich clusters and Mo/Cr/P-rich clusters. 3) Solute segregation out of solution was highest for most solutes in the thread section of the bolt #4412 with the exception of Cu, which experienced more separation out of solution into Curich clusters in the bolt head section. This highlights the difference in the mechanisms for precipitation of Ni/Si clusters, which have the Ni 3 Si phase composition, and precipitation of Cu-rich clusters. 4) There appear to be multiple simultaneous influences that affect the microstructural variation along the length of the bolt that overcomes the ~2X difference in irradiation dose between the bolt head and the bolt thread. The irradiation temperature, thermal/fast neutron ratio variation, potential strain gradient, and exposure to PWR coolant water that each section of the bolt sees may have more influence on the microstructural evolution than the total irradiation dose. The bolt thread and shank, with higher temperature, higher relative fast neutron flux, higher strain, and exposure to coolant but lower dose, underwent more enhanced cavity formation, precipitation, and solute segregation than the bolt head section.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Deep learning-based segmentation of lithium-ion battery microstructures enhanced by artificially generated electrodes

Accurate 3D representations of lithium-ion battery electrodes, in which the active particles, binder and pore phases are distinguished and labeled, can assist in understanding and ultimately improving battery performance. Here, we demonstrate a methodology for using deep-learning tools to achieve reliable segmentations of volumetric images of electrodes on which standard segmentation approaches fail due to insufficient contrast. We implement the 3D U-Net architecture for segmentation, and, to overcome the limitations of training data obtained experimentally through imaging, we show how synthetic learning data, consisting of realistic artificial electrode structures and their tomographic reconstructions, can be generated and used to enhance network performance. We apply our method to segment x-ray tomographic microscopy images of graphite-silicon composite electrodes and show it is accurate across standard metrics. We then apply it to obtain a statistically meaningful analysis of the microstructural evolution of the carbon-black and binder domain during battery operation.

25 ENERGY STORAGE↗