SEARCH · Engineering Papers

Results for “component isolation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Fiber optics for the future - wavelength division multiplexing

Optical wavelength division multiplexing (WDM) systems, with signals transmitted on different wavelengths through a single fiber, can have increased information capacity and fault isolation properties over single wavelength optical systems. This paper describes a typical WDM system. The applicability of future standards to such a system are discussed. Also, a state-of-the-art survey of optical multimode components which could be used to implement the system are made. The components to be surveyed are sources, multiplexers, and detectors. Emphasis is given to the demultiplexer techniques which are the major developmental components in the WDM system.

Spencer, J. L.↗

NASA NTRS1987

Mariner Mark II - Spacecraft control for the 1990's and beyond

The Mariner Mark II reconfigurable modular spacecraft concept will incorporate a Spacecraft Attitude and Articulation Control System of novel design. Attention is presently given to key component technologies that will be used for the first time in the Mariner Mark II; these encompass CCD-based, target-referenced extended body tracking, fiber-optic rate sensing, and momentum compensation for dynamic isolation of payloads. An analysis of star and target body-tracking requirements is presented, together with an account of the precision-pointing platform disturbance rejection properties required.

Bell, Charles E.↗

NASA NTRS1996

Structure Identification Within a Transitioning Swept-Wing Boundary Layer

Extensive measurements are made in a transitioning swept-wing boundary layer using hot-film, hot-wire and cross-wire anemometry. The crossflow-dominated flow contains stationary vortices that breakdown near mid-chord. The most amplified vortex wavelength is forced by the use of artificial roughness elements near the leading edge. Two-component velocity and spanwise surface shear-stress correlation measurements are made at two constant chord locations, before and after transition. Streamwise surface shear stresses are also measured through the entire transition region. Correlation techniques are used to identify stationary structures in the laminar regime and coherent structures in the turbulent regime. Basic techniques include observation of the spatial correlations and the spatially distributed auto-spectra. The primary and secondary instability mechanisms are identified in the spectra in all measured fields. The primary mechanism is seen to grow, cause transition and produce large-scale turbulence. The secondary mechanism grows through the entire transition region and produces the small-scale turbulence. Advanced techniques use Linear Stochastic Estimation (LSE) and Proper Orthogonal Decomposition (POD) to identify the spatio-temporal evolutions of structures in the boundary layer. LSE is used to estimate the instantaneous velocity fields using temporal data from just two spatial locations and the spatial correlations. Reference locations are selected using maximum RMS values to provide the best available estimates. POD is used to objectively determine modes characteristic of the measured flow based on energy. The stationary vortices are identified in the first laminar modes of each velocity component and shear component. Experimental evidence suggests that neighboring vortices interact and produce large coherent structures with spanwise periodicity at double the stationary vortex wavelength. An objective transition region detection method is developed using streamwise spatial POD solutions which isolate the growth of the primary and secondary instability mechanisms in the first and second modes, respectively. Temporal evolutions of dominant POD modes in all measured fields are calculated. These scalar POD coefficients contain the integrated characteristics of the entire field, greatly reducing the amount of data to characterize the instantaneous field. These modes may then be used to train future flow control algorithms based on neural networks.

Chapman, Keith↗

NASA NTRS1997

Hard X-Ray Telescope (HXT) with Simultaneous Multiwavelength Observing from UV to 1 MeV

The scientific instrumentation associated with this study includes three coaligned telescope systems: an array of grazing incidence telescopes with graded d-spacing multilayers to enhance reflectivity above 10 keV and a compound detector in their focal planes that covers the 0.1 to 100 keV band; a single laue crystal telescope that concentrates selected narrow regions in the 150 to 1300 keV bands containing interesting lines onto a cooled segmented high energy resolution germanium detector; and an array of three small UV telescopes with detectors and filters to isolate various bands in the 1000 to 2500 A region. The principal objectives of the study is to define what technology developments are required for these instruments to be built, refine the specifications of each instrument component, and identify what type of mission is needed for an HXT observatory. One key question is whether this set of instruments should be located together as an ensemble observing simultaneously aboard a single dedicated mission or distributed among multiple missions with other instrumentation.

Goenstein, Paul↗

NASA NTRS1997

Cytoskeletal mechanics in pressure-overload cardiac hypertrophy

We have shown that the cellular contractile dysfunction characteristic of pressure-overload cardiac hypertrophy results not from an abnormality intrinsic to the myofilament portion of the cardiocyte cytoskeleton but rather from an increased density of the microtubule component of the extramyofilament portion of the cardiocyte cytoskeleton. To determine how, in physical terms, this increased microtubule density mechanically overloads the contractile apparatus at the cellular level, we measured cytoskeletal stiffness and apparent viscosity in isolated cardiocytes via magnetic twisting cytometry, a technique by which magnetically induced force is applied directly to the cytoskeleton through integrin-coupled ferromagnetic beads coated with Arg-Gly-Asp (RGD) peptide. Measurements were made in two groups of cardiocytes from cats with right ventricular (RV) hypertrophy induced by pulmonary artery banding: (1) those from the pressure-overloaded RV and (2) those from the normally loaded same-animal control left ventricle (LV). Cytoskeletal stiffness increased almost twofold, from 8.53 +/- 0.77 dyne/cm2 in the normally loaded LV cardiocytes to 16.46 +/- 1.32 dyne/cm2 in the hypertrophied RV cardiocytes. Cytoskeletal apparent viscosity increased almost fourfold, from 20.97 +/- 1.92 poise in the normally loaded LV cardiocytes to 87.85 +/- 6.95 poise in the hypertrophied RV cardiocytes. In addition to these baseline data showing differing stiffness and, especially, apparent viscosity in the two groups of cardiocytes, microtubule depolymerization by colchicine was found to return both the stiffness and the apparent viscosity of the pressure overload-hypertrophied RV cells fully to normal. Conversely, microtubule hyperpolymerization by taxol increased the stiffness and apparent viscosity values of normally loaded LV cardiocytes to the abnormal values given above for pressure-hypertrophied RV cardiocytes. Thus, increased microtubule density constitutes primarily a viscous load on the cardiocyte contractile apparatus in pressure-overload cardiac hypertrophy.

Non-NASA Center↗

NASA NTRS2006

Structural Health Monitoring and Impact Detection Using Neural Networks for Damage Characterization

Detection of damage due to foreign object impact is an important factor in the development of new aerospace vehicles. Acoustic waves generated on impact can be detected using a set of piezoelectric transducers, and the location of impact can be determined by triangulation based on the differences in the arrival time of the waves at each of the sensors. These sensors generate electrical signals in response to mechanical motion resulting from the impact as well as from natural vibrations. Due to electrical noise and mechanical vibration, accurately determining these time differentials can be challenging, and even small measurement inaccuracies can lead to significant errors in the computed damage location. Wavelet transforms are used to analyze the signals at multiple levels of detail, allowing the signals resulting from the impact to be isolated from ambient electromechanical noise. Data extracted from these transformed signals are input to an artificial neural network to aid in identifying the moment of impact from the transformed signals. By distinguishing which of the signal components are resultant from the impact and which are characteristic of noise and normal aerodynamic loads, the time differentials as well as the location of damage can be accurately assessed. The combination of wavelet transformations and neural network processing results in an efficient and accurate approach for passive in-flight detection of foreign object damage.

Ross, Richard W.↗

NASA NTRS2010

Space Shuttle Orbiter Wing-Leading-Edge Panel Thermo-Mechanical Analysis for Entry Conditions

Linear elastic, thermo-mechanical stress analyses of the Space Shuttle Orbiter wing-leading-edge panels is presented for entry heating conditions. The wing-leading-edge panels are made from reinforced carbon-carbon and serve as a part of the overall thermal protection system. Three-dimensional finite element models are described for three configurations: integrated configuration, an independent single-panel configuration, and a local lower-apex joggle segment. Entry temperature conditions are imposed and the through-the-thickness response is examined. From the integrated model, it was concluded that individual panels can be analyzed independently since minimal interaction between adjacent components occurred. From the independent single-panel model, it was concluded that increased through-the-thickness stress levels developed all along the chord of a panel s slip-side joggle region, and hence isolated local joggle sections will exhibit the same trend. From the local joggle models, it was concluded that two-dimensional plane-strain models can be used to study the influence of subsurface defects along the slip-side joggle region of these panels.

Knight, Norman F., Jr.↗

NASA NTRS2011

Mount Protects Thin-Walled Glass or Ceramic Tubes from Large Thermal and Vibration Loads

The design allows for the low-stress mounting of fragile objects, like thin walled glass, by using particular ways of compensating, isolating, or releasing the coefficient of thermal expansion (CTE) differences between the mounted object and the mount itself. This mount profile is lower than true full kinematic mounting. Also, this approach enables accurate positioning of the component for electrical and optical interfaces. It avoids the higher and unpredictable stress issues that often result from potting the object. The mount has been built and tested to space-flight specifications, and has been used for fiber-optic, optical, and electrical interfaces for a spaceflight mission. This mount design is often metal and is slightly larger than the object to be mounted. The objects are optical or optical/electrical, and optical and/or electrical interfaces are required from the top and bottom. This requires the mount to be open at both ends, and for the object s position to be controlled. Thin inside inserts at the top and bottom contact the housing at defined lips, or edges, and hold the fragile object in the mount. The inserts can be customized to mimic the outer surface of the object, which further reduces stress. The inserts have the opposite CTE of the housing material, partially compensating for the CTE difference that causes thermal stress. A spring washer is inserted at one end to compensate for more CTE difference and to hold the object against the location edge of the mount for any optical position requirements. The spring also ensures that any fiber-optic or optic interface, which often requires some pressure to ensure a good interface, does not overstress the fragile object. The insert thickness, material, and spring washer size can be traded against each other to optimize the mount and stresses for various thermal and vibration load ranges and other mounting requirements. The alternate design uses two separate, unique features to reduce stress and hold the object. A release agent is applied to the inside surface of the mount just before the binding potting material is injected in the mount. This prevents the potting material from bonding to the mount, and thus prevents stress from being applied, at very low temperatures, to the fragile object being mounted. The potting material mixing and curing is temperature- and humidity-controlled. The mount has radial grooves cut in it that the potting material fills, thus controlling the vertical position of the mounted object. The design can easily be used for long and thin objects, short and wide objects, and any shape in between. The design s advantages are amplified for long and thin fragile objects. The general testing range was 45 to +45 C, but multiple mounts were successfully tested down to 60 and up to 50 C and the design can be adjusted for larger ranges.

Amato, Michael↗

NASA NTRS1975

Control logic for a 30 cm diameter ion thruster

Tests with a 30 cm thruster having EMT critical components have defined start-up criteria. Of the three phases comprising the start-up mode, the preheat phase is intended to heat critical feed system components to desired temperatures. Of the seven supplies available during the preheat phase, only three were found to be useful for purposes of preheating the thruster. These were the cathode and neutralizer tip heater supplies and the isolator heater supply. If the needed temperatures are attained during preheat, the ignition phase requires only several seconds. The heat phase serves to establish the proper propellant flow rates prior to the transition to the run mode. Using these techniques, a thruster with initial temperatures in the range of -15 to +25 C can be reliably started and provide a 1.0 amp beam within 45 min. High voltage recycle time profiles indicate limitations on several time functions.

Bechtel, R. T.↗

NASA NTRS1985

A statistical analysis of the Einstein normal galaxy sample. I - Spiral and irregular galaxies

The results of a statistical analysis of 48 spiral and irregular galaxies observed with the Einstein Observatory are reported. It is found that the X-ray luminosity is not directly correlated with the mass of the galaxies, but is strongly correlated with the blue luminosity. This suggests that most X-ray sources, including low-mass binaries, are binary systems belonging to both old disk and young arm Population I components. A real bulge population of X-ray sources exists that can contribute significantly to the X-ray luminosity of early-type spirals. The X-ray emission from a sample of 29 relatively isolated, normal elliptical and S0 galaxies is also studied, and the results are compared to those for the above sample to investigate the origin of the X-ray emission in early-type galaxies and the possible emission mechanisms. The influence of a powerful radio source and the onset of nuclear activity are also examined.

Fabbiano, G.↗

NASA NTRS1992

Sequences Of Amino Acids For Human Serum Albumin

Sequences of amino acids defined for use in making polypeptides one-third to one-sixth as large as parent human serum albumin molecule. Smaller, chemically stable peptides have diverse applications including service as artificial human serum and as active components of biosensors and chromatographic matrices. In applications involving production of artificial sera from new sequences, little or no concern about viral contaminants. Smaller genetically engineered polypeptides more easily expressed and produced in large quantities, making commercial isolation and production more feasible and profitable.

Carter, Daniel C.↗

NASA NTRS1992

Investigation of three-dimensional flow field in a turbine including rotor/stator interaction. II - Three-dimensional flow field at the exit of the nozzle

The nozzle exit flowfield was measured at two axial locations with a miniature five-hole probe. Measurements were taken from hub-to-tip, blade-to-blade at 21 radial locations and at two axial locations downstream of the nozzle trailing edge to resolve the flowfield accurately including the nozzle wake, secondary flow region, horseshoe vortex and losses. All three components of the velocity, stagnation pressure, static pressure, and pitch and yaw angles have been resolved very accurately. The wake data seems to indicate that the decay of the wake is faster than the wake of an isolated nozzle row. The cause of this is attributed to the presence of the rotor downstream. A distinct vortex core has been observed near the tip. The indications are that the horseshoe vortex and the passage vortex have merged to produce a single loss core region. Roughly a third of the blade height passage near the tip and a third of the blade height near the hub is dominated by secondary flow, passage vortex and the horseshoe vortex phenomena. Only the middle third of the nozzle behaves as per design. These and other data are presented, interpreted and synthesized to understand the nozzle flowfield.

Zaccaria, M.↗

NASA NTRS2004

Prototype Motor Controllers Demonstrated for the James Webb Space Telescope Cryogenic Environment

NASA is in the process of designing the James Webb Space Telescope. This telescope will investigate images of objects in deep space (stars, galaxies, etc.) by using light in the infrared region of the light spectrum. To make such observations, the telescope must have light sensors that operate at very cold temperatures, near absolute zero. To achieve this low-temperature tolerance, designers must place the light sensors behind a Sun shield that will prevent sunlight, and its heat, from reaching the sensors. In this cold region inside the telescope, electric motors and some motor controls must operate at temperatures near 40 K (40 degrees above absolute zero). These motors will be used to position light filters needed by the telescope. There are motors that operate at the low temperatures, but there is little technology for low-temperature motor-control electronics. The drawing shows how the motors and their controls are positioned behind the Sun shield. Simplified version of the layout of the motor and control electronics that are located, as dictated by mission requirements, in the cold zone of the James Webb Space Telescope. A Sun shield provides protection and isolation of these electronics from the heat of the rays of the sun. Room temperature compoenets (control computer, motor select command, motor phase drive, power supply, parallel to serial, and sun shield) as well as 40-kelvin components (motor select, serial to parallel, and motors) are shown. The Low Temperature Electronics Group at the NASA Glenn Research Center has been working to develop motor control electronics that will operate at a temperature of 40 K. The group conducted tests to determine which electronic components will operate at such very low temperatures. Then, components that were determined to operate successfully at the low temperatures were used to design low-temperature motor-controller circuits. A prototype motor controller circuit was built, evaluated, and demonstrated to operate at 70 K. Next, Glenn researchers plan to determine circuit performance at much colder temperatures--down to 40 K. This low-temperature program was supported by the James Webb Space Telescope Electrical Systems Design Group at the NASA Goddard Space Flight Center and by the NASA Electronic Parts and Packaging Program at NASA Headquarters and the Jet Propulsion Laboratory.

Patterson, Richard L.↗

NASA NTRS2004

The Pulse Width Modulator ASIC for Deep Space Missions

The Jet Propulsion Laboratory has started the development of a Pulse Width Modulator Application Specific Integrated Circuit (PWMA). This development is leveraging the previous development of the Switch Control ASIC (SCA). The purpose of the development is to provide the control for a selected range of power converter topologies and to meet the stringent environmental requirements of deep space missions. The PWMA will include several power control functions that are not normally included on the off-the-shelf components available today. One key functional requirement is the ability to implement an N + K redundant power converter with the ability to control the charging of a battery. Other applications will be the typical point of load isolated and non-isolated power converters. The purpose the development is not only to provide a much needed flight part, but also to accelerate the engineering process by using a standard cell library from previous ASIC developments. Under previous developments with Boeing and Lockheed Martin, JPL has produced three ASICs. Each ASIC has been implemented by using an analog standard cell library. One such development was the SCA, which is design to provide a floating power switch control. The functional verification of this ASIC has been completed and the cells used have been targeted for the new development of the PWMA. The primary function of the PWMA is to provide the control function of a point of load power converter. The design is an isolated 60 W converter with a 33 V output. In architecting the design, several functions were left up to the power converter design in order to make the ASIC more generic. The ASIC can be used for several power converter topologies and power levels. Some additional features have been added to the ASIC to provide the interfaces for multi-phase topologies and battery control functions. An N+K fault tolerant strategy has been implemented in order to provide the battery control functions. The PWMA has been developed to provide an ASIC with several functions not normally available in the off the shelf controllers. These functions have been added to enable the power converter designers to achieve fault tolerant designs and battery control functions.

Pulse Width Modulator Application Specific Integra↗

NASA NTRS2015

Forward Bay Cover Separation Modeling and Testing for the Orion Multi-Purpose Crew Vehicle

Spacecraft multi-body separation events during atmospheric descent require complex testing and analysis to validate the flight separation dynamics models used to verify no re-contact. The NASA Orion Multi-Purpose Crew Vehicle (MPCV) architecture includes a highly-integrated Forward Bay Cover (FBC) jettison assembly design that combines parachutes and piston thrusters to separate the FBC from the Crew Module (CM) and avoid re-contact. A multi-disciplinary team across numerous organizations examined key model parameters and risk areas to develop a robust but affordable test campaign in order to validate and verify the FBC separation event for Exploration Flight Test-1 (EFT-1). The FBC jettison simulation model is highly complex, consisting of dozens of parameters varied simultaneously, with numerous multi-parameter interactions (coupling and feedback) among the various model elements, and encompassing distinct near-field, mid-field, and far-field regimes. The test campaign was composed of component-level testing (for example gas-piston thrusters and parachute mortars), ground FBC jettison tests, and FBC jettison air-drop tests that were accomplished by a highly multi-disciplinary team. Three ground jettison tests isolated the testing of mechanisms and structures to anchor the simulation models excluding aerodynamic effects. Subsequently, two air-drop tests added aerodynamic and parachute elements, and served as integrated system demonstrations, which had been preliminarily explored during the Orion Pad Abort-1 (PA-1) flight test in May 2010. Both ground and drop tests provided extensive data to validate analytical models and to verify the FBC jettison event for EFT-1. Additional testing will be required to support human certification of this separation event, for which NASA and Lockheed Martin are applying knowledge from Apollo and EFT-1 testing and modeling to develop a robust human-rated FBC separation event.

Ali, Yasmin↗

NASA NTRS2018

Validation and Norms of Cognition and Spaceflight Assessments with Senior Military Leaders

Spaceflight hazards include risks to cognitive performance. NASA requires sensitive neuropsychological screening tools to determine changes to cognitive risks to crew health and performance. Currently, NASA uses WinSCAT (Spaceflight Cognitive Assessment Tool for Windows) for neurocognitive screening and to monitor the status of astronauts during spaceflight. The CognitionTest Battery was recently developed by NASA-funded researchers at UPenn as part of the Behavioral Health and Performance component of NASA Standard Measures. This research provides independently validated norms and psychometric properties to compare WinSCAT to Cognition using a military population who operates in high demand, extreme environments similar to those experienced by astronauts (deployments, isolation, extreme environments).

Williams, T. J.↗

NASA NTRS2020

PACE Propulsion Subsystem Surge Analysis and Testing

Propulsion subsystem surge analysis and testing was performed at NASA Goddard Space Flight Center (GSFC) in order to analytically and experimentally determine the potential for damaging dynamic pressure events in the Plankton Aerosol Cloud and ocean Ecosystem (PACE) propulsion subsystem. Surge pressures occur when propellant flow is initiated following the actuation of an isolation valve separating an upstream high pressure fluid from a downstream low pressure manifold. By design, the PACE propulsion subsystem mitigates surge pressures using an orifice, or a cavitating venturi, placed upstream of each thruster bank isolation latch valve. Venturi sizing is a balancing act due to the competing performance goals of staying within the margins of an acceptable pressure loss and maintaining surge pressures below the proof pressure rating of the subsystem components. Subsystem pressure loss is dependent upon the venturi throat diameter and is higher for smaller venturi sizes. A venturi with a smaller throat diameter incurs an increased pressure loss through the orifice resulting in a reduced thruster inlet pressure and diminished thruster performance. The PACE propulsion subsystem surge analysis and testing supports system optimization, i.e. pressure drop minimization, while still meeting the surge pressure requirements to maximize overall system performance. In this paper a new approach to surge pressure analytical gauging is discussed, as well as its accuracy when compared to traditional surge testing campaign.

Space↗

NASA NTRSDate not supplied

Advances in Integrally Formed Metallic Structures

NASA Langley Research Center (LaRC) is applying flow forming technology to aerospace aluminum alloys for the manufacture of integrally stiffened cylinders that meet aircraft fuselage or launch vehicle specifications. High-strength 2xxx series alloys, in various temper/product form conditions, are being compared with medium-strength, very formable AA 6061 as the benchmark. Screening of candidate materials traditionally relies on empirical forming trials, but more recently on metrics derived from constant nominal strain rate tensile testing. In this work, the established hierarchy of formability metrics is adopted as the baseline; tensile area reduction, work hardening exponent, and modulus of resilience. The suite of metrics can be expanded based on phenomenological and mechanistic considerations of plastic flow instabilities to incorporate anisotropy ratio, rate of work hardening, and dynamic strain aging effects. Separate research thrusts at LaRC are aimed at formulating a protocol for scalable production of fully formed, defect-free components: 1) quantifying the extended set of formability metrics from constant and jump strain rate tensile tests with digital image correlation (DIC); 2) using statistically designed experiments on a vertical spin/flow forming facility (WF VUD-600®) to isolate the effect of convenient process variables, such as axial feed rate and thickness reduction; and 3) predicting the effect of feed ratio (roller translation relative to mandrel rotation speeds) on material response via process modeling using the DEFORM® simulation software. Current results will be discussed in terms of correlating intrinsic material properties with the bulk workability characteristics to successfully fabricate cylinders with complex cross-sections.

Aluminum↗