Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cathode and anode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Electron Delocalization Enables Sulfone-based Single-solvent Electrolyte for Lithium Metal Batteries

Li-metal batteries (LMB), although providing high energy density, face the grand challenge of identifying good electrolyte solvents for cycling. Common solvents are either only stable against lithium metal anode or only stable against LiNi x MnyCo 1-x-y O 2 (NMC) cathode. There is significant effort trying to increase the cathode stability for ether electrolytes, which are in general stable against lithium metal anode. In comparison, there is much less effort trying to increase the anode stability of electrolytes that are stable against NMC cathode. One example is the sulfone-based electrolyte. It has good cathode stability but is hindered from practical application because of (1) high viscosity and poor wetting capability and (2) poor anode stability. Here, we solve these issues by modifying the sulfone molecules using resonance and electron withdrawing effect. The viscosity is significantly reduced by delocalizing the electrons through introducing additional oxygen on the molecular backbone and applying appropriate fluorination. The resulting molecule 2,2,2-trifluoroethyl mesylate (TFEM) has decreased Lewis basicity and less reactivity toward Li + . In conclusion, the electrolyte based on TFEM as single solvent enables cycling of LMB under harsh conditions of low N/P ratio (21 mg/cm 2 NMC811 and 50 μm Li) with 90 % capacity retention after 160 cycles at C/3 discharge rate.

25 ENERGY STORAGE↗
DOE OSTI2022

Study of Cathode Gas Diffusion Architecture for Improved Oxygen Transport in Hydroxide Exchange Membrane Fuel Cells

The high pH environment in hydroxide exchange membrane fuel cells (HEMFCs) has the potential to reach lower costs than the current proton exchange membrane fuel cells (PEMFCs), the incumbent technology. A significant difference between HEMFCs and PEMFCs is the location of water production within the cell. In PEMFCs, the water is produced on the cathode, limiting oxygen transport. In HEMFCs, the water is produced on the anode where the fuel is pure hydrogen. This allows the cathode to be optimized for oxygen transport without the presence of excess liquid water. Limiting current analysis, a technique previously used in PEMFCs, is adopted in HEMFCs to evaluate the oxygen mass transport resistances for different sections of the cathode. Through elimination of the microporous layer (MPL), gas diffusion layer (GDL), and traditional flow field and using porous nickel foam for gas distribution, the transport resistance at an operating condition of 150 kPa(g) and with the cell temperature at 80 °C was decreased from 112 s m −1 to 48 s m −1 , effectively halved. The optimal configuration for performance was found with Ni foam and a GDL, eliminating the MPL and traditional flow field, which vastly improved oxygen transport while maintaining adequate electrical contact with the cathode catalyst layer.

25 ENERGY STORAGE↗
DOE OSTI2022

Ethylene Carbonate–Free Electrolytes for Stable, Safer High–Nickel Lithium–Ion Batteries

Ethylene carbonate (EC) is an important component in state-of-the-art electrolytes for lithium-ion batteries (LIBs). However, EC is highly susceptible to oxidation on the surface of high-nickel layered oxide cathodes, making it undesirable for next-generation high-energy-density LIBs. In this study, a simple, yet effective, EC-free electrolyte (20F1.5M-1TDI) is presented by adding 20 wt% fluoroethylene carbonate (FEC) and 1 wt% lithium 4,5-dicyano-2-(trifluoromethyl)imidazole (LiTDI) into 1.5 M LiPF 6 in an ethyl methyl carbonate (EMC) electrolyte. The 20F1.5M-1TDI electrolyte is found to efficiently passivate the graphite anode and stabilize high-nickel cathodes by a synergistic decomposition of FEC and LiTDI. The LiNi 0.9 Mn 0.05 Al 0.05 O 2 (NMA90)/graphite full cell with the 20F1.5M-1TDI electrolyte, therefore, exhibits an enhanced cycling stability and a suppressed voltage hysteresis growth compared to that with an EC-containing baseline electrolyte (1 M LiPF 6 in EC:EMC, 3:7 in weight, with 2 wt% vinyl carbonate). Advanced analytical tools, such as time-of-flight secondary ion mass spectrometry and X-ray photoelectron spectroscopy, are employed to understand the underlying working mechanism of the EC-free electrolyte. Furthermore, the present study clearly showcases the great potential of EC-free electrolytes as a straightforward, practical approach for LIBs with high-nickel cathodes.

electrode/electrolyte interface↗
DOE OSTI2024

A highly oxygen reduction reaction active and CO 2 durable high-entropy cathode for solid oxide fuel cells

One big obstacle for the oxygen reduction reaction (ORR) electrode in solid oxide fuel cells (SOFCs) is the poor reaction activity and fast degradations caused by CO 2 poisoning. Here, in this study, we report our design of an active A-site Ca-rich high-entropy Pr 0.1875 Ba 0.1875 Sr 0.1875 La 0.1875 Ca 0.25 CoO 3-δ (PBSLC 25 C) electrode, guided by the O p-band theory. Here, when applied as a cathode in solid oxide fuel cells (SOFCs), it demonstrates high ORR activity and excellent CO 2 tolerance under realistic operating conditions. Ni-YSZ-based anode-supported cells with PBSLC 25 C cathodes demonstrate excellent peak power densities of 1.14 W cm -2 , 1.04 W cm -2 , and 0.77 W cm -2 in the air with 1%, 5%, and 10% CO 2 , respectively, at 750 °C. The engineered high-entropy PBSLC 25 C effectively diminishes the CO 2 poisoning effect and maintains active surfaces for fast oxygen exchange, as confirmed by the cell durability test in air containing CO 2 (5 and 10 vol%), Raman spectroscopy, and density functional theory calculations.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

A04-0491 - Reduced Electrolyte Reactivity of Pitch-Carbon Coated Si Nanoparticles for Li-Ion Battery Anodes

Silicon-based anodes for Li-ion batteries (LIB) have the potential to increase the energy density over graphite-based LIB anodes. However, silicon anodes exhibit poor cycle and calendar lifetimes due to mechanical instabilities and high chemical reactivity with the carbonate-based electrolytes that are typically used in LIBs. In this work, we synthesize a pitch-carbon coated silicon nanoparticle composite active material for LIB anodes that exhibits reduced chemical reactivity with the carbonate electrolyte compared to an uncoated silicon anode. Silicon primary particle sizes <10 nm minimize micro-scale mechanical degradation of the anode composite, while conformal coatings of pitch-carbon minimized the parasitic reactions between the silicon and the electrolyte. When matched with a high voltage NMC622 cathode, the pitch-carbon coated Si anode retains -75% of its initial capacity over 1000 cycles. Efforts to increase the areal loading of the pitch-carbon coated silicon anodes to realize real energy density improvements over graphite anodes results in severe mechanical degradation on the electrode level. Developing procedures to engineer the architecture of the composite silicon anode may be a solution to this mechanical challenge.

DIRECT ENERGY CONVERSION,ENERGY STORAGE↗
DOE OSTI2024

Operando Investigation on the Role of Densification and Chemo-Mechanics on Solid-State Cathodes

All solid-state batteries are desirable for a range of energy storage applications which require high energy density. Achieving a high energy density in a solid-state battery requires the operation of an energy dense anode with a composite solid-state cathode. Pores and/or voids within a solid state cathode are ion-blocking and thus control over the concentration and distribution of pores in the initial electrode and cycled electrode is desirable. This study provides an understanding of the interplay between electrode microstructure and mechanics on active material utilization in solid state cathodes composed of NCM 811 and Li 6 PS 5 Cl. Decreasing the solid electrolyte particle size leads to greater active material-electrolyte contact and less total deformation when exposed to an external load. Composite cathodes with greater compliance can potentially decrease strain between the active material and solid electrolyte, decrease delamination events and result in higher overall active material utilization and high capacity retention.

25 ENERGY STORAGE↗
DOE OSTI2021

Extended cycle life implications of fast charging for lithium-ion battery cathode

Enabling extreme fast charging (XFC, =10–15 min charging) requires a comprehensive understanding of its implications. While lithium plating is a key bottleneck for the anode, the full extent of limitations for the cathode are not well-understood, particularly in extended-cycle settings with well-defined battery designs and conditions. This article presents cycle-life implications of XFC on cathodes at multiple length scales, combining electrochemical analyses, degradation modeling, and post-test characterizations. The comprehensive test matrix includes 41 well-defined gr/NMC pouch cells under varied fast-charge rates (1–9C) and state-of-charges cycled up to 1000 times. Cathode issues remain minimal in early cycling, but begin to accelerate in later life, when distinct cracking is found and identified as a fatigue mechanism. The bulk structure of cathodes remains intact, but distinct particle surface reconstruction is observed; however, this shows less pronounced effect on cathode aging than does cracking.

25 ENERGY STORAGE↗
DOE OSTI2023

Composite Lithium Metal Structure to Mitigate Pulverization and Enable Long‐Life Batteries

In lithium metal batteries, non‐uniform stripping of lithium results in pit formation, which promotes subsequent non‐uniform, dendritic deposition. This viscous cycle leads to pulverization of lithium which promotes cell shorting or capacity degradation, symptoms further exaggerated by high electrode areal loading and lean electrolytes. Here, to address this challenge, a composite lithium metal anode is engineered that contains uniformly distributed, nanometer‐sized carbon particles. This composite lithium is shown to strip more uniformly since the growth of non‐uniform pits is intercepted by the carbon particles. This mechanism is corroborated by a continuum electrochemical model. Subsequent lithium deposition on carbon particles is also found to be more uniform than on the surface with irregular pits. Notably, the pulverization rate of composite lithium is 26 times slower than that of commercial lithium. Moreover, in a Li‐S battery with sulfurized polyacrylonitrile cathode, the use of the composite anode extends the cycle life by three times when the areal capacity is 8 mAh cm −2 . The approach of using an engineered lithium composite structure to address challenges during both stripping and plating can inform future designs of lithium metal anodes for high areal capacity operations.

high areal capacity↗
DOE OSTI2022

Electrolytic Methane Production from Reactive Carbon Solutions

Here, we report an electrochemical reactor that converts 3.0 M KHCO 3 into methane at the cathode, and oxidizes water at the anode. The molar ratio of methane product to unreacted CO 2 gas (defined herein as "methane yield") was measured to be 34% at a partial current density of 120 mA cm -2 . The highest previously reported CO 2 -to-methane yield is 3%. Our reactor achieved this improvement in methane yield because it is fed with 3.0 M KHCO 3 , a type of reactive carbon solution, rather than gaseous CO 2 . The reactor uses H + delivered by a bipolar membrane to form CO 2 at the cathode. This CO 2 is subsequently reduced into methane. A cationic surfactant added to the catholyte suppressed hydrogen evolution and increased methane formation. A 1D continuum model confirmed that H + from the membrane promotes the formation of methane over multicarbon products at the cathode. These findings present design principles for electrochemical methane synthesis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

In-situ visualization of the transition metal dissolution in layered cathodes

Transition metal dissolution in layered cathodes is one of the most intractable issues that deteriorates the battery performance and lifetime. It not only aggravates the structure degradation in cathode, but also damages the solid electrolyte interphase in anode and even induce the formation of lithium dendrites. In this work, we investigate the dissolution behaviors of polycrystalline and single-crystalline layered cathode via operando X-ray imaging techniques. The described cathode particle morphology appears to have a significant impact on the evolution of the dissolution dynamics. As a mitigation strategy, we reveal that doping with trace amount of Zr in the layered cathode could improve its robustness against the transition metal dissolution. Our finding provides valuable insights for designing the next-generation highly-stable layered battery cathodes.

25 ENERGY STORAGE↗
DOE OSTI2023

SPUTTERED THIN FILMS FOR VERY HIGH POWER, EFFICIENT, AND LOW-COST COMMERCIAL SOFCS

The aim of this project was to leverage the low area specific resistance (ASR) of Redox’s GDC electrolyte-based cell architecture and increase solid oxide fuel cell (SOFC) efficiency (i.e., open circuit voltage, or OCV) without significantly increasing cell resistance. The key to achieving the increased SOFC efficiency is the introduction of a thin sputtered yttria stabilized zirconia (YSZ) electron-blocking layer and a thin sputtered gadolinia doped ceria (GDC) barrier layer on top of the half-cell substrate (i.e., anode and GDC electrolyte). A key initial effort of the project was to improve the quality of the half-cell substrate surface so that any remaining defects were significantly smaller than the desired film thickness. During lab-scale trials, we had to overcome challenges with film cracking during post-sputtering treatments (e.g., thermal anneals) as well as damage to the sputtering targets. After the initial lab-scale trials, the focus shifted toward the use of commercial scale sputtering equipment with a sputtering equipment manufacturer in the microelectronics industry. Using the commercial sputtering equipment, we deposited films with different variations of power, PO2, sputtering time, platen speed, etc. We then determined the combinations of sputtering conditions and post-sputtering treatments that yielded high-quality films without cracks or other significant defects. While thin films were deposited on cells as large as 10 cm by 10 cm, the processing was optimized using 4 cm by 4 cm cells. Cell performance was evaluated in stainless-steel test fixtures between 500 °C and 700 °C with hydrogen fuel fed to the anode and air fed to the cathode. Extensive studies allowed us to determine that modified cathode and cathode contact firing processes were required to achieve theoretical OCV. Moreover, use of the new firing processes resulted in the need for a modified cathode contact to achieve a low ASR. In summary, the project demonstrated the performance of high OCV (1.13 V at 650 °C) from sputtered layers and a low ASR (~0.25 Ohms-cm2 at 650 °C) resulting from a modification of cathode/contact processing and the introduction of alternative contact layers that are sufficient to yield a Gen-1 cell with a maximum power density of approximately 1.2 W/cm2. At an operating voltage of 0.74 V, this would yield a cell power density of ~1.1 W/cm2. While not utilized in this project, a Redox Gen-2 cell has a catalyst-infiltrated porous anode that reduces the ASR by more than 50% from that of the Gen-1 cells used in this project. Therefore, if the sputtered YSZ electron-blocking layer and GDC barrier layer are added to a Gen-2 half cell with a similar increase in OCV to the theoretical value of ~1.13 V at 650 °C, and if the same improvement in ASR (from that demonstrated in this project) is achieved when using the Gen-2 half-cell architecture as a sputtered cell substrate, then the power density at 0.74 Vop could be as high as ~2.6 W/cm2. The impact of such power density gains, while still maintaining high cell efficiency, and thus high system efficiency, is a dramatic decrease in system cost because the stack represents ~30-40% of the SOFC system cost.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Dynamic Molecular Investigation of the Solid-Electrolyte Interphase of an Anode-Free Lithium Metal Battery Using In Situ Liquid SIMS and Cryo-TEM

Solid electrolyte interphase (SEI) has been widely perceived to play a critical role in the stable cycling of rechargeable batteries. However, associated with the fragile and air-sensitive nature of the SEI layer, delineation of the formation process and the nature of SEI remains a big challenge. Here, we use in situ liquid time-of-flight secondary ion mass spectroscopy (TOF-SIMS), cryo- transmission electron microscope (TEM) and density functional theory (DFT) calculation to delineate molecular process on the formation of SEI layer under the dynamic operating condition. We discover that the onset potential for SEI layer formation and the thickness of the SEI show dependence on the solvation shell structure. Using LiCoO 2 as a cathode and Cu film as an anode, the SEI is noticed to start to form at around 2.0 V and reach its final thickness (irreversible part, ~ 40-50 nm) at about 3.0 V in the 1 M LiPF 6 –EC/DMC electrolyte, while for the case of 1 M LiFSI–DME, the SEI starts to form at around 1.5 V and reaches its final thickness (~ 20 nm) at about 2.0 V. The in situ TOF-SIMS clearly indicates the outer SEI layer formation and dissipation upon charging and discharging, implying a continued evolution of electrolyte structure with extended cycling. In conclusion, the present work establishes a direct correlation between the molecular signature of SEI layer with solvation feature of electrolytes in lithium batteries, providing insights for tailoring SEI layer toward improved electrochemical properties of lithium batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

A reactive wetting strategy improves lithium metal reversibility

The cycling of lithium metal (Li 0 ) anode is often accompanied by irregular lithium plating/stripping, leading to poor Li 0 reversibility, and posing a grand challenge to constructing reliable Li 0 batteries. Hereby, we report a reactive wetting strategy to enable conformal and highly reversible Li 0 plating/stripping through a lithium-reactive substrate. In this study, the reactive wetting, smooth nucleation, and conformal growth behaviors of Li 0 are visualized through in-situ transmission electron microscopy, ex-situ scanning electron microscope, and in-situ optical microscope characterizations. Based on the reactive wetting substrate, high average Coulombic efficiencies (99.0% at 0.5 mA cm -2 for 400 cycles) are realized for Li 0 anodes. By pre-plating Li 0 into the reactive wetting substrate as anodes and leveraging LiFePO 4 as cathodes, high capacity retention (76.0% after 200 cycles in low N/P ratio conditions) is also achieved in the as-constructed Li 0 full cells. This work establishes a fundamental understanding of reactive wetting dynamics of Li 0 and provides a drop-in solution to improving Li 0 reversibility.

25 ENERGY STORAGE↗
DOE OSTI2023

Electron Delocalization Enables Sulfone-based Single-solvent Electrolyte for Lithium Metal Batteries

Li-metal batteries (LMB), although providing high energy density, face the grand challenge of identifying good electrolyte solvents for cycling. Common solvents are either only stable against lithium metal anode or only stable against LiNi x Mn y Co 1-x-y O 2 (NMC) cathode. There is significant effort trying to increase the cathode stability for ether electrolytes, which are in general stable against lithium metal anode. In comparison, there is much less effort trying to increase the anode stability of electrolytes that are stable against NMC cathode. One example is the sulfone-based electrolyte. It has good cathode stability but is hindered from practical application because of (1) high viscosity and poor wetting capability and (2) poor anode stability. Here, we solve these issues by modifying the sulfone molecules using resonance and electron withdrawing effect. The viscosity is significantly reduced by delocalizing the electrons through introducing additional oxygen on the molecular backbone and applying appropriate fluorination. The resulting molecule 2,2,2-trifluoroethyl mesylate (TFEM) has decreased Lewis basicity and less reactivity toward Li + . The electrolyte based on TFEM as single solvent enables cycling of LMB under harsh conditions of low N/P ratio (21 mg/cm 2 NMC811 and 50 μm Li) with 90 % capacity retention after 160 cycles at C/3 discharge rate.

25 ENERGY STORAGE↗
DOE OSTI2023

Delineating the Impact of Transition‐Metal Crossover on Solid‐Electrolyte Interphase Formation with Ion Mass Spectrometry

Abstract Lithium‐metal batteries (LMB) employing cobalt‐free layered‐oxide cathodes are a sustainable path forward to achieving high energy densities, but these cathodes exhibit substantial transition‐metal dissolution during high‐voltage cycling. While transition‐metal crossover is recognized to disrupt solid‐electrolyte interphase (SEI) formation on graphite anodes, experimental evidence is necessary to demonstrate this for lithium‐metal anodes. In this work, advanced high‐resolution 3D chemical analysis is conducted with time‐of‐flight secondary‐ion mass spectrometry (TOF‐SIMS) to establish spatial correlations between the transition metals and electrolyte decomposition products found on cycled lithium‐metal anodes. Insights into the localization of various chemistries linked to crucial processes that define LMB performance, such as lithium deposition, SEI growth, and transition‐metal deposition are deduced from a precise elemental and spatial analysis of the SEI. Heterogenous transition‐metal deposition is found to perpetuate both heterogeneous SEI growth and lithium deposition on lithium‐metal anodes. These correlations are confirmed across various lithium‐metal anodes that are cycled with different cobalt‐free cathodes and electrolytes. An advanced electrolyte that is stable to higher voltages is shown to minimize transition‐metal crossover and its effects on lithium‐metal anodes. Overall, these results highlight the importance of maintaining uniform SEI coverage on lithium‐metal anodes, which is disrupted by transition‐metal crossover during operation at high voltages.

Chemistry↗
DOE OSTI2020

Redox Mechanism in Na-Ion Battery Cathodes Probed by Advanced Soft X-Ray Spectroscopy

A Na-ion battery (NIB) device is a promising solution for mid-/large-scale energy storage, with the advantages of material abundance, low cost, and environmental benignity. To improve the NIB capacity and retainability, extensive efforts have been put into the developments of NIB electrode materials. The redox activities of the transition metal (TM)-based NIB electrodes are critical in defining the capacity and stability. Here, we provide a comprehensive review on recent studies of the redox mechanisms of NIB cathodes through synchrotron-based soft X-ray absorption spectroscopy (sXAS) and mapping of resonant inelastic X-ray scattering (mRIXS). These soft X-ray techniques are direct and effective tools to fingerprint the TM-3d and O-p states with both bulk and surface sensitivities. Particularly, 3d TM L-edge sXAS has been used to quantify the cationic redox contributions to the electrochemical property; however, it suffers from lineshape distortion for the bulk sensitive signals in some scenarios. With the new dimension of information along the emitted photon energy, mRIXS can address the distortion issue of in TM-L sXAS; moreover, it also breaks through the limitation of conventional sXAS on detecting unconventional TM and O states, e.g., Mn(I) in NIB anode and oxidized oxygen in NIB cathodes. The mRIXS fingerprint of the oxidized oxygen state enables the detection of the reversibility of the oxygen redox reaction through the evolution of feature intensity upon electrochemical cycling and thus clarifies various misunderstandings in our conventional wisdom. We conclude that, with mRIXS established as a powerful tool, its potential and power will continue to be explored for characterizing novel chemical states in NIB electrodes.

25 ENERGY STORAGE↗
DOE OSTI2019

Toward Long-Life, Ultrahigh-Nickel Layered Oxide Cathodes for Lithium-Ion Batteries: Optimizing the Interphase Chemistry with a Dual-Functional Polymer

Boosting the Ni content in LiMO 2 (M = Ni, Co, Mn, etc.) layered oxides is a promising way to establish high-energydensity, low-cost cathodes, but the poor cathode surface stability is a daunting challenge for their practical viability. Herein, by constructing a dual-functional binder framework with a conductive polymer - polyaniline (PANI), the ultrahigh-Ni layered oxide cathode (LiNi 0.94 Co 0.06 O 2 ) exhibits significantly improved cyclability, with a capacity retention greatly increased from 47% to 81% over 1,000 cycles in full cells. It is demonstrated that the acidic species (e.g. HF) in the electrolyte can be efficiently scavenged through a protonation process of PANI, hence the cathode surface reactivity is greatly suppressed and the rock-salt phase propagation into bulk structure is considerably alleviated. Furthermore, the PANI binder system effectively prevents both the cathode-electrolyte interphase (CEI) and anode-electrolyte interphase (AEI) from degrading to a thick “triple-layer” architecture upon extensive cycling, resulting in more robust, thinner CEI and AEI with regulated interphasial chemistry. Moreover, the delocalized π-conjugated electrons along the backbone of PANI facilitate fast electron transfer and promote rate capability even at low temperatures (-20 °C). Finally, this work sheds light on rational binder engineering for developing high-energy-density lithium-ion batteries with acceptable cycle life.

25 ENERGY STORAGE↗