SEARCH · Engineering Papers

Results for “casting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Cellulose triacetate, thin film dielectric capacitor

Very thin films of cellulose triacetate are cast from a solution containing a small amount of high boiling temperature, non-solvent which evaporates last and lifts the film from the casting surface. Stretched, oriented, crystallized films have high electrical breakdown properties. Metallized films less than about 2 microns in thickness form self-healing electrodes for high energy density, pulsed power capacitors. Thicker films can be utilized as a dielectric for a capacitor.

Yen, Shiao-Ping S.↗

NASA NTRS1995

A polyimide molecular composite

A polyimide is a hard and sturdy thermoplastic made from the combination of tetracarboxylic dianhydrides and diamines in a polar aprotic solvent. A series of polyimide blends comprising of a tough moldable, wholly aromatic polyimide and a highly crystalline rigid polyimide were prepared. The flexible polyimide was based on LaRC-SI with a 2% offset, and the rigid polyimide as based on para-phenylenediamine and biphenyltetracarboxylic dinnhydride encapped with pthalic anhydride. The polyimide blends were cast as films and cured at 100, 200, and 300 C in air. These films were characterized by finding their glass-transition temperature, melting temperature, coefficient of thermal expansion, tensile modulus, tensile strength, and percent elongation. These characterizations found out which polyimide blend had exceptional mechanical and thermal properties. Experimental results showed the following: (1) A blend with increasing amounts of flexible polyimide produced a better film; (2) A blend with increasing amounts of rigid polyimide produced a brittle film; (3) LaRC-SI (2% offset) tended to phase separate during film casting; (4) Most of the films produced were brittle; and (5) There was an inability to obtain mechanical and thermal properties due to having brittle film. These conclusions demonstrate the difficulty in producing a polyimide blend comprising two physically distinct polyimides. Combining a polysmide with a poly(amic acid) thermosett could be the next phase of research in polyimide synthesis.

Hart, Aprill J.↗

NASA NTRS1995

Synthesis of low color, atomic oxygen resistant polyimides

The purpose of this project was to develop low color, atomic oxygen resistant polyimides for potential applications on spacecraft in low earth orbit. The material is needed in order to protect satellites and spacecraft from the gases and radiation found at those altitudes. Phosphorous containing polyimides have been shown to be especially resistant to corrosion and weight loss under oxygen plasma. Unfortunately the color of these phosphorous containing polyimides is still too high for them to be good heat insulators. While they are not as effective as teflon, the current material of choice. polyimides are much less dense than teflon and would be especially valuable if they could be made with low color. The approach taken was to synthesize a monomer which would contain the elements needed for giving the final polyimide its desired properties. In particular the monomer should incorporate phosphine or phosphine oxides and have bulky side groups to block any color forming charge transfer structures. The target molecule, 3,5-di-(trifluoromethylphenyl)-bis(3-aminophenyl) phosphine oxide, (containing both a phosphine oxide group and a bulky ditrifluoromethylphenyl group) was synthesized via three reactions in overall yield of 21 percent. In addition, a model compound, bis(3-phenylamine) phenyl phosphine oxide, was synthesized two different ways in order to establish the conditions for the nitration of phosphine oxides and their reduction to the amine. Finally, a trisubstituted phosphine oxide was synthesized. In all, seven phosphorus containing organic compounds were synthesized, purified and characterized. The model compound was reacted with oxydiphthalic anhydride to form a polyamic acid with inherent viscosity of 0.34. This material was cast into a film and heated, forming a normally colored fairly strong polyimide with a Tg of 240 C. The target compound was reacted with 6-fluorodiphthalic anhydride to give a polyamic acid with inherent viscosity of 0.19 and cast to give a heavily cracked colored film with a Tg of 230 C.

MacInnes, Dave↗

NASA NTRS1994

SSME Main Combustion Chamber (MCC) 'Hot Oil' Dewaxing

In an attempt to comply with the changing environmental regulations, a process was developed for the replacement of perchloroethylene in the dewaxing of the Space Shuttle Main Engine (SSME) Main Combustion Chamber (MCC) and other associated hardware filled with the Rigidax(registered mark) casting compound. Rigidax(registered mark) is a hard blue-dyed, calcium carbonate filled thermoplastic casting compound (melting point 77 C) that is melted and poured into hardware cavities to prevent contamination during material removal processes, i.e. machining, grinding, drilling, and deburring. Additionally, it serves as a maskant for designated areas during electroforming processes. Laboratory testing was conducted to evaluate seven alternate fluids for the replacement of perchloroethylene in the dewaxing process. Based upon successful laboratory results, a mineral oil was selected for testing on actual hardware. The final process developed involves simultaneous immersion and flushing of the MCC channels using a distinct eight stage process. A nonvolatile hydrocarbon analysis of a solvent flush sample is performed to determine the hardware cleanliness for comparison to the previous perchloroethylene dewaxing process.

Akpati, Anthony U.↗

NASA NTRS1996

Wear and Friction Behavior of Metal Impregnated Microporous Carbon Composites

Metal-matrix composites have been prepared by pressure-infiltration casting of copper-base alloy melts into microporous carbon preforms. The carbon preforms contained varying proportions of amorphous carbon and graphite. Load dependence of the wear and friction behavior of the composite pins has been examined under ambient conditions against cast-iron plates, using a pin-on-plate reciprocating wear tester. The wear resistance of the composite is significantly improved, as compared with the base alloy. Contrary to the normally expected behavior, the addition of graphite to the amorphous carbon does not reduce the friction coefficient, especially at high loads. The wear and friction behavior of the composites is very sensitive to the size and distribution of the microstructural constituents.

Goller, Gultekin↗

NASA NTRS1966

Fully Deuterated Aliphatic Hydrocarbons Obtained From Iron Carbide Treated with DCl and D2O

According to Oparin, Mendeleev thought that the origin of petroleum was the result of the hydrolysis of iron carbides by superheated steam under pressure from the deep interior of the Earth through geological formations where the metal carbides exist. As early as 1877, Mendeleev described the reaction leading to the synthesis of hydrocarbons according to the general equation 3Fe(sub m)C(sub n) + mH2O yields mFe3O4 + C(sub 3n)H(sub 8m). Other experimental studies on the production of hydrocarbons from cast iron have been reported. Because of the possibility that hydrocarbons may have been trapped within the carbon matrix of the cast iron, which usually has a high content of carbon, we have studied the reaction of pure iron carbide with deuterium chloride and deuterated water. This was done in order to distinguish any newly formed deuterated hydrocarbons from any possible impurities of trapped hydrocarbons. The experiments were carried out by simply allowing iron carbide to react with concentrated deuterium chloride in D2O. The volatile hydrocarbon fraction examined by gas chromatography-mass spectrometry (GC/MS), using a Finnigan 1020/OWA instrument. contained low molecular weight hydrocarbons in a range C3 to C7. Lower molecular weight hydrocarbons were not detected by GC/MS because the MS scanning mode was preset above mass 40 to exclude components of air. The identified hydrocarbons are similar to those obtained under prebiotic conditions using high frequency discharge. The hydrocarbons found in common were propane, butane, pentane, 3-methylpentane, hexane, and heptane. The percent yields decline with increasing carbon number (propane 11%, n-heptane 1%). Similar results have been obtained by the direct treatment of metal carbides by pulse laser vaporization mass spectrometry. These results show that the hydrolysis of iron carbides may have been a significant source of hydrocarbons on the primitive Earth. There appears to be a predominance of straight chain isomers, which may have been important in the prebiotic synthesis of membrane-forming compounds.

Marquez, C.↗

NASA NTRS1996

Advancement of Solidification Processing Technology Through Real Time X-Ray Transmission Microscopy: Sample Preparation

Two types of samples were prepared for the real time X-ray transmission microscopy (XTM) characterization. In the first series directional solidification experiments were carried out to evaluate the critical velocity of engulfment of zirconia particles in the Al and Al-Ni eutectic matrix under ground (l-g) conditions. The particle distribution in the samples was recorded on video before and after the samples were directionally solidified. In the second series samples of the above two type of composites were prepared for directional solidification runs to be carried out on the Advanced Gradient Heating Facility (AGHF) aboard the space shuttle during the LMS mission in June 1996. X-ray microscopy proved to be an invaluable tool for characterizing the particle distribution in the metal matrix samples. This kind of analysis helped in determining accurately the critical velocity of engulfment of ceramic particles by the melt interface in the opaque metal matrix composites. The quality of the cast samples with respect to porosity and instrumented thermocouple sheath breakage or shift could be easily viewed and thus helped in selecting samples for the space shuttle experiments. Summarizing the merits of this technique it can be stated that this technique enabled the use of cast metal matrix composite samples since the particle location was known prior to the experiment.

Stefanescu, D. M.↗

NASA NTRS1998

Barotropic Tidal Predictions and Validation in a Relocatable Modeling Environment

Under funding from the Office of Naval Research (ONR), and the Naval Oceanographic Office (NAVOCEANO), the Mississippi State University Center for Air Sea Technology (CAST) has been working on developing a Relocatable Modeling Environment(RME) to provide a uniform and unbiased infrastructure for efficiently configuring numerical models in any geographic/oceanic region. Under Naval Oceanographic Office (NAVO-CEANO) funding, the model was implemented and tested for NAVOCEANO use. With our current emphasis on ocean tidal modeling, CAST has adopted the Colorado University's numerical ocean model, known as CURReNTSS (Colorado University Rapidly Relocatable Nestable Storm Surge) Model, as the model of choice. During the RME development process, CURReNTSS has been relocated to several coastal oceanic regions, providing excellent results that demonstrate its veracity. This report documents the model validation results and provides a brief description of the Graphic user Interface (GUI).

Mehra, Avichal↗

NASA NTRS1998

Interactions Between Solidification and Compositional Convection in Alloys

This project combined theoretical and experimental ground-based studies of the interactions between convection and solidification of binary melts. Particular attention was focused on the alteration of the composition and microstructure of castings caused by convective flows through the interstices of mushy layers. Two different mechanisms causing convection were investigated. (i) Compositional, buoyancy driven convection is known to cause chimneys and freckles in directionally cast alloys on Earth. The analytical studies provide quantitative criteria for the formation of chimneys that can be used to assess the expediency of producing alloys in Space. (ii) Flow of the melt is also driven by the contraction (expansion) that typically occurs during change of phase. Such convection will occur even in the absence of gravity, and may indeed be the primary cause of macrosegregation during the production of alloys in Space. The studies will employed asymptotic methods in order to determine conditions for the stability of various states of solidifying systems. Further, simple macroscopic models of complete systems were developed and solved. These analytical studies were augmented by laboratory experiments using aqueous solutions, in which the convective flows could be easily observed and the effects of convection could be readily measured. These y experiments guided the development of the theoretical models and provided data against which the predictions of the models can be tested.

Davis, S. H.↗

NASA NTRS1998

MoSi2-Base Hybrid Composite Passed Engine Test

The intermetallics compound molybdenum disilicide (MoSi2) is an attractive high-temperature structural material for advanced engine applications. It has excellent oxidation resistance, a high melting point, relatively low density, and high thermal conductivity, and it is easily machined. Past research'at the NASA Lewis Research Center has resulted in the development of a hybrid composite consisting of a MoSi2 matrix reinforced with silicon nitride (Si3N4) Particulate and silicon carbide (SiC) fibers. This composite has demonstrated attractive strength, toughness, thermal fatigue, and oxidation resistance, including resistance to "pest" oxidation. These properties attracted the interest of the Office of Naval Research and Pratt & Whitney, and a joint NASA/Navy/Pratt & Whitney effort was developed to continue to mature the MoSi2 Composite technology. A turbine blade outer air seal, which was part of the Integrated High Performance Turbine Engine Technology (IHPTET) program, was chosen as a first component on which to focus. The first tasks of the materials development effort were to develop improved processing methods to reduce costs and to use fine-diameter fibers that enable the manufacturing of complex shapes. Tape-casting methods were developed to fully infiltrate the fine SiC fibers with matrix powders. The resulting composites were hot pressed to 100-percent density. Composites with cross-plied fiber architectures with 30 vol. % hi-nicalon SiC fibers and 30 vol. % nitride particles are now made routinely and demonstrate a good balance of properties. The next task entailed the measurement of a wide variety of mechanical properties to confirm the suitability of this composite in engines. In particular, participants in this effort demonstrated that composites made with Hi-Nicalon fibers had strength and toughness properties equal to or better than those of the composites made with the large-diameter fibers that had been used previously. Another critically important property measured was impact resistance. Aircraft engine components require sufficient toughness to resist manufacturing defects, assembly damage, stress concentrations at notches, and foreign object damage. Engine company designers indicated that impact resistance would have to be measured before they would seriously consider these types of composites. The Charpy V-notch test was chosen to assess impact resistance, and both monolithic and composite versions Of MOSi2 were tested from -300 to 1400 C. The results (see the following graphs) show that nitride-particulate-reinforced MoSi2 exhibited impact resistance higher than that of many monolithic ceramics and intermetallics, and that the fiber-reinforced composites had even higher values, approaching that of cast superalloys.

Keith, Theo G., Jr.↗

NASA NTRS1998

Barotropic Tidal Predictions and Validation in a Relocatable Modeling Environment

Under funding from the Office of Naval Research (ONR), the Mississippi State University Center for Air Sea Technology (CAST) has been working on developing a Relocatable Modeling Environment (RME) to provide a uniform and unbiased infrastructure for efficiently configuring numerical models in any geographic or oceanic region. Under Naval Oceanographic Office (NAVOCEANO) funding, the model was implemented and tested for NAVOCEANO use. With our current emphasis on ocean tidal modeling, CAST has adopted the Colorado University's numerical ocean model, known as CURReNTSS (Colorado University Rapidly Relocatable Nestable Storm Surge) Model, as the model of choice. During the RME development process, CURReNTSS has been relocated to several coastal oceanic regions, providing excellent results that demonstrate its veracity. This report documents the model validation results and provides a brief description of the Graphic user Interface.

Mehra, Avichal↗

NASA NTRS1999

Real-Time Investigation of Solidification of Metal Matrix Composites

Casting of metal matrix composites can develop imperfections either as non- uniform distributions of the reinforcement phases or as outright defects such as porosity. The solidification process itself initiates these problems. To identify or rectify the problems, one must be able to detect and to study how they form. Until, recently this was only possible by experiments that employed transparent metal model organic materials with glass beads to simulate the reinforcing phases. Recent results obtained from a Space Shuttle experiment (using transparent materials) will be used to illustrate the fundamental physics that dictates the final distribution of agglomerates in a casting. We have further extended this real time investigation to aluminum alloys using X-ray microscopy. A variety of interface-particle interactions will be discussed and how they alter the final properties of the composite. A demonstration of how a solid-liquid interface is distorted by nearby voids or particles, particle pushing or engulfment by the interface, formations of wormholes, Aggregation of particles, and particle-induced segregation of alloying elements will be presented.

Kaukler, William↗

NASA NTRS1999

The Isothermal Dendritic Growth Experiment (IDGE): USMP-4 One-Year-Report

Dendrites describe the tree-like crystal morphology commonly assumed in many material systems--particularly in metals and alloys that freeze from supercooled or supersaturated melts. There remains a high level of engineering interest in dendritic solidification because of the role of dendrites in the determination of cast alloy microstructures. Microstructure plays a key role in determining the physical properties of cast or welded products. In addition, dendritic solidification provides an example of non-equilibrium physics and is one of the simplest non-trivial examples of dynamic pattern formation, where an amorphous melt, under simple starting conditions, evolves into a complex ramified microstructure. Although it is well-known that dendritic growth is controlled by the transport of latent heat from the moving solid-melt interface as the dendrite advances into a supercooled melt, an accurate, and predictive model has not been developed. Current theories consider: 1) the transfer of heat or solute from the solid-liquid interface into the melt, and 2) the interfacial crystal growth and growth selection physics for the interface. However, the effects of gravity-induced convection on the transfer of heat from the interface prevent either element from being adequately tested solely under terrestrial conditions. The Isothermal Dendritic Growth Experiment (IDGE) constituted a series of three NASA-supported microgravity experiments, all of which flew aboard the space shuttle, Columbia. This experimental space flight series was designed and operated to grow and record dendrite solidification in the absence of gravity-induced convective heat transfer, and thereby produce a wealth of benchmark-quality data for testing solidification scaling laws. The data collection from the on-orbit phase of the IDGE flight series is now complete. We are currently completing analyses and moving towards final data archiving.

Glicksman, M. E.↗

NASA NTRS2000

Development of Metal Matrix Composites for NASA'S Advanced Propulsion Systems

The state-of-the-art development of several aluminum and copper based Metal Matrix Composites (MMC) for NASA's advanced propulsion systems will be presented. The presentation's goal is to provide an overview of NASA-Marshall Space Flight Center's planned and on-going activities in MMC for advanced liquid rocket engines such as the X-33 vehicle's Aerospike and X-34 Fastrac engine. The focus will be on lightweight and environmental compatibility with oxygen and hydrogen of key MMC materials, within each NASA's new propulsion application, that will provide a high payoff for NASA's reusable launch vehicle systems and space access vehicles. Advanced MMC processing techniques such as plasma spray, centrifugal casting, pressure infiltration casting will be discussed. Development of a novel 3D printing method for low cost production of composite preform, and functional gradient MMC to enhanced rocket engine's dimensional stability will be presented.

Lee, Jonathan A.↗

NASA NTRS2000

Effects of Melt Convection and Solid Transport on Macrosegregation and Grain Structure in Equiaxed Al-Cu Alloys

Macrosegregation in metal casting can be caused by thermal and solutal melt convection, and the transport of unattached solid crystals resulting from nucleation in the bulk liquid or dendrite fragmentation. To develop a comprehensive numerical model for the casting of alloys, an experimental study has been conducted to generate benchmark data with which such a solidification model could be tested. The objectives were: (1) experimentally study the effects of solid transport and thermosolutal convection on macrosegregation and grain size; and (2) provide a complete set of boundary conditions temperature data, segregation data, and grain size data - to validate numerical models. Through the control of end cooling and side wall heating, radial temperature gradients in the sample and furnace were minimized. Thus the vertical crucible wall was adiabatic. Samples at room temperature were 24 cc and 95 mm long. The alloys used were Al-1 wt. pct. Cu, and Al- 10 wt. pct. Cu; the starting point for solidification was isothermal at 710 and 685 C respectively. To induce an equiaxed structure various amounts of the grain refiner TiB2 were added. Samples were either cooled from the top, or the bottom. Several trends in the data stand out. In attempting to model these experiments, concentrating on these trends or differences may be beneficial.

Rerko, Rodney S.↗

NASA NTRS2000

A Solid Case for Microgravity Processing

Solidification of metals, particularly alloys, is a complicated process. At some sufficiently high temperature, the components comprising an alloy fully mix, producing a single homogeneous liquid. Unfortunately, after this liquid is cast into a mold and allowed to freeze, the resulting solid is usually very inhomogeneous. In most cases the first solid to "freeze out" of the liquid has a composition very close to one of the pure metals. This initially solidifying metal usually comprises microscopic, pine-tree shaped components, collectively referred to as a dendritic array, whose distribution, alignment, and scale directly influence a materials strength and docility. During dendrite growth the adjacent liquid becomes enriched, and consequently, solidifies a much lower temperature and considerably later time. Thus, in the course of solidification, both the solid and the enriched liquid can have compositions (and local temperatures) significantly different from those of the bulk liquid. Different compositions and temperatures imply different densities that, in Earth's gravity, induce motion in the liquid. Such motion promotes formation of a casting that is denser at the bottom and lighter at the top. This condition known as macrosegregation, precludes optimized, uniform material properties.

Grugel, Richard N.↗

NASA NTRS2000

Numerical Calculation of the Drag Force Acting on a Solid Particle Pushed by a Solid/Liquid Interface

The distribution of insoluble particles in a metal casting depends primarily on the interaction of the particles with the solid/liquid interface (SLI) during the solidification process. The balance of the forces acting on the particle essentially determines whether a particle will be engulfed or pushed by the SLI. An important component of this force balance is the drag force generated by the particle motion in front of the SLI. Previously developed mathematical models for particle/SLI interaction made use of steady-state solutions of this force provided by the lubrication theory. However, our numerical model based on the SLI tracking approach shows that the steady-state approach is inappropriate to model the interaction process and that at steady-state the theoretical solution underestimates the drag force. It was found that regression analysis of steady-state numerical solutions for cylindrical particles moving normal to a flat SLI gives a relationship of the form: Abstract The distribution of insoluble particles in a metal casting depends primarily on the interaction of the particles with the solid/liquid interface (SLI) during the solidification process. The balance of the forces acting on the particle essentially determines whether a particle will be engulfed or pushed by the SLI. An important component of this force balance is the drag force generated by the particle motion in front of the SLI. Previously developed mathematical models for particle/SLI interaction made use of steady-state solutions of this force provided by the lubrication theory. However, our numerical model based on the SLI tracking approach shows that the steady-state approach is inappropriate to model the interaction process and that at steady-state the theoretical solution underestimates the drag force. It was found that regression analysis of steady-state numerical solutions for cylindrical particles moving normal to a flat SLI gives a relationship of the form: F(sub D, sup num) =sqoare root of 3(pi)(eta)V(sub p)(R(sub p)/d)(sup 10(gamma)/3). This is to compared to the solution provided by the lubrication theory: F(sub D), sup theor) = 3 square root of 2(pi)(eta)V(sub p)(R(sub p)/d)(sub 3/2), where F(sub D) is the drag force, eta is the dynamic viscosity of the fluid, V(sub p) is the particle velocity, R(sub p) is the particle radius, gamma is Euler's constant (gamma approx. = 0.577), and d is the width of the gap between the particle and the SLI. The domain on which the equations proposed by the lubrication theory are relevant is clearly identified in the paper. The numerical model was then validated against the classical lubrication theory within the domain of its validity.

Catalina, Adrian V.↗

NASA NTRS2001

Adaptive-Grid Methods for Phase Field Models of Microstructure Development

Modeling solidification microstructures has become an area of intense study in recent years. The properties of large scale cast products, ranging from automobile engine blocks to aircraft components and other industrial applications, are strongly dependent on the physics that occur at the mesoscopic and microscopic length scales during solidification. The predominant morphology found in solidification microstructures is the dendrite, a tree-like pattern of solid around which solidification proceeds. The microscopic properties of cast products are determined by the length scales of these dendrites, and their associated segregation profiles. For this reason understanding the mechanisms for pattern selection in dendritic growth has attracted a great deal of interest from the experimental and theoretical communities. In particular, a great deal of research has been undertaken to understand such issues as dendrite morphology, shape and growth speed. Experiments on dendrite evolution in pure materials by Glicksman and coworkers on succinonitrile (SCN), and more recently pivalic acid (PVA), as well as other transparent analogs of metals, have provided tests of theories for dendritic growth, and have stimulated considerable theoretical progress. These experiments have clearly demonstrated that in certain parameter ranges the physics of the dendrite tip can be characterized by a steady value for the dendrite tip velocity, radius of curvature and shape. Away from the tip, the time-dependent dendrite exhibits a characteristic sidebranching as it propagates, which is not yet well understood. These experiments are performed by observing individual dendrites growing into an undercooled melt. The experiments are characterized by the dimensionless undercooling. Most experiments are performed at low undercooling.

Dantzig, Jonathan A.↗