SEARCH · Engineering Papers

Results for “boundary layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

All sources NASA NTRS DOE OSTI

NASA NTRS2016

Transient Growth Analysis of Compressible Boundary Layers with Parabolized Stability Equations

The linear form of parabolized linear stability equations (PSE) is used in a variational approach to extend the previous body of results for the optimal, non-modal disturbance growth in boundary layer flows. This methodology includes the non-parallel effects associated with the spatial development of boundary layer flows. As noted in literature, the optimal initial disturbances correspond to steady counter-rotating stream-wise vortices, which subsequently lead to the formation of stream-wise-elongated structures, i.e., streaks, via a lift-up effect. The parameter space for optimal growth is extended to the hypersonic Mach number regime without any high enthalpy effects, and the effect of wall cooling is studied with particular emphasis on the role of the initial disturbance location and the value of the span-wise wavenumber that leads to the maximum energy growth up to a specified location. Unlike previous predictions that used a basic state obtained from a self-similar solution to the boundary layer equations, mean flow solutions based on the full Navier-Stokes (NS) equations are used in select cases to help account for the viscous-inviscid interaction near the leading edge of the plate and also for the weak shock wave emanating from that region. These differences in the base flow lead to an increasing reduction with Mach number in the magnitude of optimal growth relative to the predictions based on self-similar mean-flow approximation. Finally, the maximum optimal energy gain for the favorable pressure gradient boundary layer near a planar stagnation point is found to be substantially weaker than that in a zero pressure gradient Blasius boundary layer.

Compressible boundary layer↗

NASA NTRS1992

Modeling variable blowing effects in the turbulent hypersonic boundary layer

Studies of the effects of variable blowing in turbulent hypersonic boundary layers are presented. Numerical calculations of the skin friction and surface heat transfer rates are compared to the experimental measurements of Holden (1990) for a slender cone at zero angle of attack in steady flows at Mach numbers of 11 and 13. An analysis of the transpiration feed system of the cone model was performed and showed that the blowing rate could be variable along the cone surface. This effect is confirmed by internal pressure measurements which were taken inside the cone model. The blowing rates are recalibrated using the internal gauge readings and used as the wall boundary condition for a compressible turbulent boundary layer calculation using the low Reynolds number k-epsilon model of Chien (1982). At low blowing rates, the boundary layer calculations indicate that a situation where both the effects of suction and blowing are present within the same flow. The results show excellent qualitative prediction of the experimental data.

Vanosdol, John G.↗

NASA NTRS2018

Experimental Evaluation of BLI Propulsion: The Boundary Layer Ingesting Inlet/Distortion-Tolerant Fan Solution

NASA has successfully developed a new testbed configuration for experimentally evaluating embedded boundary layer ingesting aircraft propulsors in its 8'x6' Supersonic Wind Tunnel. This testbed meets the challenges of providing the necessary freestream flow Mach conditions and desired range and distribution of boundary layer thickness for embedded aircraft propulsion systems. The testbed consists of a 48ft long raised wind tunnel floor aircraft surface simulator and a boundary layer regulation system to produce propulsion-local aircraft aerodynamic flow fields. This durable special test equipment is designed to be installed in the wind tunnel's transonic test section and is capable of evaluating a wide range of subcritical and supercritical airframe-propulsion integration configurations for subsonic cruise aircraft. The wind tunnel and testbed are well suited for meeting the test requirements of these propulsors in the most cost efficient way and has been aerodynamically calibrated and proven through tests of a first-of-its-kind boundary layer ingesting propulsor.

Arend, David J.↗

NASA NTRSDate not supplied

Some Effects of Tunnel Noise on Cylinder-Induced Mach 6 Transitional Shock Wave Boundary Layer Interactions

Experiments were conducted on a cylinder-induced shock wave boundary layer interaction (SBLI)as its state was brought through transition using a combination of boundary layer trips and Reynolds number sweep. A baseline case with no trips was also examined. The measurements were made in a Mach 6 freestream in the well-characterized Actively Controlled Expansion tunnel, which demonstrated a near tripling in fluctuation levels with unit Reynolds number increase from 3.0 to 3.5 million per meter. Surface oil flow and schlieren images suggested the jump in freestream noise served as the impetus for SBLI transition since the flow separation distance began to decrease as the Reynolds number progressed through those conditions. Likewise, surface mounted Kulite® pressure transducers indicated a rise in surface pressure fluctuations as well as initial growth in the instability responsible for transitioning the boundary layer within the interaction. Finally, heat transfer rates within the tripped SBLI were shown to be affected by the jump in freestream disturbance levels.

Andrew N Leidy↗

NASA NTRS1990

Boundary-layer stability analysis of flight-measured transition data

Correlation of in-flight boundary-layer transition experiments with linear boundary-layer stability theory contributes both to the validation of the numerical methods as well as the analysis of the measured transition process. Transition results obtained in a recent flight experiment, in which the extent of laminar flow and the transition process on the wing of a business-jet fitted with an instrumented glove section were determined, are analyzed. The experiment was conducted at freestream Mach numbers from 0.55 to 0.82, chord Reynolds numbers from 10 to 20 x 10 to the 6th, and leading-edge sweep angles 17 deg to 20 deg. The growth of both Tollmien-Schlichting and crossflow instabilities are predicted using the e exp n method for several flight conditions and the calculated n-factors at transition onset are correlated. Comparison of the measured dominant boundary-layer disturbance frequencies and the predicted unstable frequencies shows fair agreement for several of the flight conditions studied.

Obara, Clifford J.↗

NASA NTRS1976

Three-dimensional boundary layers approaching separation

The theory of semi-similar solutions of the laminar boundary layer equations is applied to several flows in which the boundary layer approaches a three-dimensional separation line. The solutions obtained are used to deduce the nature of three-dimensional separation. It is shown that in these cases separation is of the "ordinary" type. A solution is also presented for a case in which a vortex is embedded within the three-dimensional boundary layer.

Williams, J. C., III↗

NASA NTRS1994

Stability of separating subsonic boundary layers

The primary and subharmonic instabilities of separating compressible subsonic two-dimensional boundary layers in the presence of a two-dimensional roughness element on a flat plate are investigated. The roughness elements considered are humps and forward- and backward-facing steps. The use of cooling and suction to control these instabilities is studied. The similarities and differences between the instability characteristics of separating boundary layers and those of the boundary layer over a flat plate with a zero pressure gradient are pointed out and discussed. The theoretical results agree qualitatively and quantitatively with the experimental data of Dovgal and Kozlov. Cooling and suction decrease the growth rates of primary and subharmonic waves in the attached-flow regions but increase them in the separated-flow regions.

Masad, Jamal A.↗

NASA NTRS2021

Assimilation of Lidar Planetary Boundary Layer Height Observations

Lidar backscatter and wind retrievals of the planetary boundary layer height (PBLH) are assimilated into 22 hourly forecasts from the NASA Unified - Weather and Research Forecast (NU-WRF) model during the Plains Elevated Convection Convection at Night (PECAN) campaign on July 11, 2015 in Greensburg, Kansas, using error statistics collected from the model profiles to compute the necessary covariance matrices. Two separate forecast runs using different PBL physics schemes were employed, and comparisons with 6 independent radiosonde profiles were made for each run. Both of the forecast runs accurately predicted the PBLH and the state variable profiles within the planetary boundary layer during the early morning, and the assimilation had a small impact during this time. In the late afternoon, the forecast runs showed decreased accuracy as the convective boundary layer developed. However, assimilation of the Doppler lidar PBLH observations were found to improve the temperature and V velocity profiles relative to independent radiosonde profiles. Water vapor was overcorrected, leading to increased differences with independent data. Errors in the U velocity were made slightly larger. The computed forecast error covariances between the PBLH and state variables were found to rise in the late afternoon, leading to the larger improvements in the afternoon. This work represents the first effort to assimilate PBLH into forecast states using ensemble methods.

Andrew Tangborn↗

NASA NTRS2006

Shuttle Return To Flight Experimental Results: Cavity Effects on Boundary Layer Transition

The effect of an isolated rectangular cavity on hypersonic boundary layer transition of the windward surface of the Shuttle Orbiter has been experimentally examined in the Langley Aerothermodynamics Laboratory in support of an agency-wide effort to prepare the Shuttle Orbiter for return to flight. This experimental study was initiated to provide a cavity effects database for developing hypersonic transition criteria to support on-orbit decisions to repair a damaged thermal protection system. Boundary layer transition results were obtained using 0.0075-scale Orbiter models with simulated tile damage (rectangular cavities) of varying length, width, and depth. The database contained within this report will be used to formulate cavity-induced transition correlations using predicted boundary layer edge parameters.

Liechty, Derek S.↗

NASA NTRS1997

Effect of Free Stream Turbulence and Other Vortical Disturbances on a Laminar Boundary Layer

This paper is concerned with the effect of free-stream turbulence on the pretransitional flat-plate boundary layer. It is assumed that either the turbulence Reynolds number or the downstream distance (or both) is small enough so that the flow can be linearized. The dominant disturbances in the boundary layer, which are of the Klebanoff type, are governed by the linearized unsteady boundary-region equations, i.e., the Navier Stokes equations with the streamwise derivatives neglected in the viscous and pressure-gradient terms. The turbulence is represented as a superposition of vortical free-stream Fourier modes, and the corresponding individual Fourier component solutions to the boundary-region equations are obtained numerically. The results are then superposed to compute the root mean square of the fluctuating streamwise velocity in the boundary layer produced by the actual free-stream turbulence. The calculated boundary-layer disturbances are in good quantitative agreement with the experimentally observed Klebanoff modes when strong low-frequency anisotropic effects are included in the free-stream turbulence spectrum. We discuss some additional effects that may need to be accounted for in order to obtain a complete description of the Klebanoff modes.

Goldstein, Marvin E.↗

NASA NTRS1980

Interaction between a normal shock wave and a turbulent boundary layer at high transonic speeds. I - Pressure distribution

Asymptotic solutions are derived for the pressure distribution in the interaction of a weak normal shock wave with a turbulent boundary layer. The undisturbed boundary layer is characterized by the law of the wall and the law of the wake for compressible flow. In the limiting case considered, for 'high' transonic speeds, the sonic line is very close to the wall. Comparisons with experiment are shown, with corrections included for the effect of longitudinal wall curvature and for the boundary-layer displacement effect in a circular pipe.

Messiter, A. F.↗

NASA NTRS1973

Boundary-layer losses

The primary cause of losses in a turbine is the boundary layer that builds up on the blade and end-wall surfaces. Analytical and experimental methods for determining the friction, trailing edge, and mixing losses associated with the boundary layer are reported. The theory presented herein refers primarily to two dimensional blade section boundary layers. Methods for obtaining three dimensional blade plus end wall losses from the two-dimensional results are also discussed.

Herman W Prust, Jr.↗

NASA NTRS1975

Particle motion in atmospheric boundary layers of Mars and Earth

To study the eolian mechanics of saltating particles, both an experimental investigation of the flow field around a model crater in an atmospheric boundary layer wind tunnel and numerical solutions of the two- and three-dimensional equations of motion of a single particle under the influence of a turbulent boundary layer were conducted. Two-dimensional particle motion was calculated for flow near the surfaces of both Earth and Mars. For the case of Earth both a turbulent boundary layer with a viscous sublayer and one without were calculated. For the case of Mars it was only necessary to calculate turbulent boundary layer flow with a laminar sublayer because of the low values of friction Reynolds number; however, it was necessary to include the effects of slip flow on a particle caused by the rarefied Martian atmosphere. In the equations of motion the lift force functions were developed to act on a single particle only in the laminar sublayer or a corresponding small region of high shear near the surface for a fully turbulent boundary layer. The lift force functions were developed from the analytical work by Saffman concerning the lift force acting on a particle in simple shear flow.

White, B. R.↗

NASA NTRS2005

High Reynolds Number Investigation of a Flush Mounted, S-Duct Inlet With Large Amounts of Boundary Layer Ingestion

An experimental investigation of a flush-mounted, S-duct inlet with large amounts of boundary layer ingestion has been conducted at Reynolds numbers up to full scale. The study was conducted in the NASA Langley Research Center 0.3-Meter Transonic Cryogenic Tunnel. In addition, a supplemental computational study on one of the inlet configurations was conducted using the Navier-Stokes flow solver, OVERFLOW. Tests were conducted at Mach numbers from 0.25 to 0.83, Reynolds numbers (based on aerodynamic interface plane diameter) from 5.1 million to 13.9 million (full-scale value), and inlet mass-flow ratios from 0.29 to 1.22, depending on Mach number. Results of the study indicated that increasing Mach number, increasing boundary layer thickness (relative to inlet height) or ingesting a boundary layer with a distorted profile decreased inlet performance. At Mach numbers above 0.4, increasing inlet airflow increased inlet pressure recovery but also increased distortion. Finally, inlet distortion was found to be relatively insensitive to Reynolds number, but pressure recovery increased slightly with increasing Reynolds number.This CD-ROM supplement contains inlet data including: Boundary layer data, Duct static pressure data, performance-AIP (fan face) data, Photos, Tunnel wall P-PTO data and definitions.

Berrier, Bobby L.↗

NASA NTRS1989

Curvature effects on the stability of three-dimensional laminar boundary layers

The linear stability equations for compressible, three-dimensional laminar boundary layer flow are derived in an orthogonal curvilinear coordinate system. The system of equations is solved using a finite difference scheme in order to study the effects of streamline and surface curvature and compressibility on the stability of the flow past a swept wing. It is known that convex surface curvature can have a stabilizing effect on the laminar boundary layer. Conversely, concave surface curvature can be destabilizing. The magnitude of these effects for swept wings is determined. Results indicate that amplification rates and hence, N-factors, for the flow over the convex upper surface of a swept wing can be reduced by about 15 to 45 percent when curvature effects are included in the linear stability analysis. The results of the calculations show that concave curvature destabilizes crossflow type disturbances with a significant increase in amplification rate. In addition, comparisons are made with some experimental results on a swept concave-convex surface. Calculated velocity vector plots show good agreement with observed disturbances in the laminar boundary layer over the concave surface.

Collier, F. S., Jr.↗

NASA NTRS1993

Interaction of solar wind with the magnetopause-boundary layer and generation of magnetic impulse events

The transport of mass, momentum, energy and waves from the solar wind to the Earth's magnetosphere takes place in the magnetopause-boundary layer region. Various plasma processes that may occur in this region have been proposed and studied. In this paper, we present a brief review of the plasma processes in the dayside magnetopause-boundary layer. These processes include (1) flux transfer events at the dayside magnetopause, (2) formation of plasma vortices in the low-latitude boundary layer by the Kelvin-Helmholtz instability and coupling to the polar ionosphere, (3) the response of the magnetopause to the solar wind dynamic pressure pulses, and (4) the impulsive penetration of solar wind plasma filaments through the dayside magnetopause into the magnetospheric boundary layer. Through the coupling of the magnetopause-boundary layer to the polar ionosphere, those above processes may lead to occurrence of magnetic impulse events observed in the high-latitude stations.

Lee, L. C.↗

NASA NTRS1974

Measurement and correlation of aerodynamic heating to surface corrugation stiffened structures in thick turbulent boundary layers

The flow conditions for which heating distributions were measured on corrugated surfaces and wavy walls in turbulent boundary layers are shown, along with the ratio of the displacement thickness to the roughness height versus the local edge Mach number for an equivalent smooth surface. The present data are seen to greatly extend the range of data available on corrugated surfaces in turbulent boundary layers. These data were obtained by testing fullscale corrugation roughened panels in the wall boundary layer of a supersonic and hypersonic wind tunnel. The experimental program used to obtain the data is described. The data are analyzed and correlated in terms of the pertinent flow and geometric parameters. The developed correlations are compared with the available thin boundary layer data, as well as with previously published correlation techniques.

Brandon, H. J.↗

NASA NTRS2012

In-Flight Boundary-Layer Transition on a Large Flat Plate at Supersonic Speeds

A flight experiment was conducted to investigate the pressure distribution, local flow conditions, and boundary-layer transition characteristics on a large flat plate in flight at supersonic speeds up to Mach 2.0. The primary objective of the test was to characterize the local flow field in preparation for future tests of a high Reynolds number natural laminar flow test article. The tests used a F-15B testbed aircraft with a bottom centerline mounted test fixture. A second objective was to determine the boundary-layer transition characteristics on the flat plate and the effectiveness of using a simplified surface coating for future laminar flow flight tests employing infrared thermography. Boundary-layer transition was captured using an onboard infrared imaging system. The infrared imagery was captured in both analog and digital formats. Surface pressures were measured with electronically scanned pressure modules connected to 60 surface-mounted pressure orifices. The local flow field was measured with five 5-hole conical probes mounted near the leading edge of the test fixture. Flow field measurements revealed the local flow characteristics including downwash, sidewash, and local Mach number. Results also indicated that the simplified surface coating did not provide sufficient insulation from the metallic structure, which likely had a substantial effect on boundary-layer transition compared with that of an adiabatic surface. Cold wall conditions were predominant during the acceleration to maximum Mach number, and warm wall conditions were evident during the subsequent deceleration. The infrared imaging system was able to capture shock wave impingement on the surface of the flat plate in addition to indicating laminar-to-turbulent boundary-layer transition.

Banks, Daniel W.↗