Results for “block design” — Page 35

DOE OSTI2021

RELAP5-3D Modeling of High Temperature Test Facility (HTTF)

HTTF at Oregon State University (OSU) Reference: General Atomics? modular high-temperature gas-cooled reactor Helium cooled, electrically heated Prismatic graphite blocks in the core and reflectors Alumina ceramic blocks are used to simulate the core and top and bottom reflectors One-fourth scale in length and diameter Most of the coolant channels in the core are full scale Lower pressure compared to the prototype reactor Over 500 instruments Designed primarily to investigate depressurized conduction cooldown (DCC) transients

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

Status of the Down-Blending of Irradiated IGR Graphite Fuel in Kazakhstan

Dry processing remains the primary solution for managing the down-blending of irradiated IGR HEU fuel. Several tasks have been initiated and completed to achieve this, including lab modernization, lab-scale and full-scale testing, designing and fabricating an in-paddle mixing drum, and commissioning both a down-blending system and a crushing and milling system. Additionally, a testing and training center was modernized, the equipment was successfully commissioned, and the IGR HEU fuel blocks were repackaged into daily containers. The training of operators and the construction of a new down-blending facility are tasks that will need to be completed in the near future. The progress in these areas continues to validate that the proposed method for down-blending irradiated HEU graphite fuel, followed by cementation of the down-blended material for permanent disposition, appears to be achievable.

12 - MGMT OF RADIOACTIVE AND NON-RADIOACTIVE WASTE↗

DOE OSTI2022

An extrapolation method for strain ranges and hold times in developing the EPP+SMT creep-fatigue design curves for Alloy 617

Experimental and numerical studies in developing the integrated Elastic–Perfectly Plastic (EPP) plus Simplified Model Test (SMT) design methodology, referred to as the EPP+SMT method, continued in FY2022. This report focuses on the methods for extrapolating the EPP+SMT creep-fatigue (CF) design curves at long hold times and low strain ranges. In this study, the available CF failure data on Alloy 617 at 950°C were analyzed to determine a set of CF failure criteria. At very low strain ranges and long hold times, CF failure data are not accessible by experiments because of the extraordinarily long test durations and the inability of the test machines to accurately control these small strain ranges. A CF experimental approach with the concept of block-strain range CF testing protocol was developed. Tests using this protocol were conducted to generate the needed information for calibrating material parameters of the numerical material models. The Time Fraction based method and Dissipated Energy method were used to extrapolate the CF life curves to low strain ranges and long hold times. Based on the new experimental approach and CF life prediction methods, the CF life curves with various hold times were developed for Alloy 617 at 950°C. In addition, an experiment was designed and is being performed to verify the predicted CF curves at 950°C. The extrapolation procedure will be applied at lower temperatures to complete the development of the EPP+SMT CF design curves for Alloy 617 in F2023.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Pathways to fluorescence via restriction of intramolecular motion in substituted tetraphenylethylenes

The design of materials with enhanced luminescence properties is a fast-developing field due to the potential applicability of these materials as light-emitting diodes or for bioimaging. A transparent way to enhance the emission properties of interesting molecular candidates is blocking competing and unproductive non-radiative relaxation pathways by the restriction of intramolecular motions. Rationalized functionalization is an important possibility to achieve such restrictions. Using time-dependent density functional theory (TD-DFT) based on the ωB97XD functional and the semiempirical tight-binding method including long-range corrections (TD-LC-DFTB), this work investigates the effect of functionalization of the paradigmatic tetraphenylethylene (TPE) on achieving restricted access to conical intersections (RACI). Photodynamical surface hopping simulations have been performed on a larger set of compounds including TPE and ten functionalized TPE compounds. Functionalization has been achieved by means of electron-withdrawing groups, bulky groups which block the relaxation channels via steric hindrance and groups capable of forming strong hydrogen bonds, which restrict the motion via the formation of hydrogen bond channels. Most of the investigated functionalized TPE candidates show ultrafast deactivation to the ground state due to their still existing structural flexibility, but two examples, one containing –CN and –CF 3 groups and a second characterized by a network of hydrogen bonds, have been identified as interesting candidates for creating efficient luminescence properties in solution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Toward controlling wetting hysteresis with nanostructured surfaces derived from block copolymer self-assembly

The synthesis of nanostructured surfaces via block copolymer (BCP) self-assembly enables a precise control of the surface feature shape within a range of dimensions of the order of tens of nanometers. Herein, this work studies how to exploit this ability to control the wetting hysteresis and liquid adhesion forces as the substrate undergoes chemical aging and changes in its intrinsic wettability. Via BCP self-assembly we fabricate nanostructured surfaces on silicon substrates with a hexagonal array of regular conical pillars having a fixed period (52 nm) and two different heights (60 and 200 nm), which results in substantially different lateral and top surface areas of the nanostructure. The wetting hysteresis of the fabricated surfaces is characterized using force–displacement measurements under quasistaic conditions and over sufficiently long periods of time for which the substrate chemistry and surface energy, characterized by the Young contact angle, varies significantly. The experimental results and theoretical analysis indicate that controlling the lateral and top area of the nanostructure not only controls the degree of wetting hysteresis but can also make the advancing and receding contact angles less susceptible to chemical aging. These results can help rationalize the design of nanostructured surfaces for different applications such as self-cleaning, enhanced heat transfer, and drag reduction in micro/nanofluidic devices.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2022

Diffusion bonded compact heat exchanger in Inconel 740H for high temperature and high-pressure applications

It is desired to develop heat exchangers able to be operated at high temperatures (750°C) and pressures (3636 psi) for use in advanced Brayton power cycle. Conventional materials have not had the high strength at temperature required for these applications previously, however a fairly new material Inconel 740H developed by Special Metals for the ultra-supercritical water fossil industry has shown good performance under these conditions. In further efforts to capitalize on these new high strength high temperature alloys CompRex has developed a diffusion bonding procedure capable of alloying compact high effectiveness heat exchangers that can perform under these high temperature and high-pressure conditions. Initial tests of the heat exchanger are being conducted at the University of Wisconsin using supercritical CO2 working fluid. The bonding process has been adjusted such that the strength of the bonded block has achieved over 90% yield and tensile strength of the 740H base material values. Grain size before and after bonding were measured to determine the extent of grain growth and grain diffusion across the interface. A discussion of the heat exchanger design, etching and initial tensile tests on sample bonds will be discussed.

14 SOLAR ENERGY↗

DOE OSTI2022

Low Enriched Fuel Fabrication Safeguards Modeling

The Material Protection, Accounting, and Control Technologies (MPACT) program utilizes modeling and simulation to assess Material Control and Accountability (MC&A) concerns for a variety of nuclear facilities. Single analyst tools allow for rapid design and evaluation of advanced approaches for new and existing nuclear facilities. A low enriched uranium (LEU) fuel conversion and fabrication facility simulator has been developed to assist with MC&A for existing LEU fuel fabrication for light water reactors. Simulated measurement blocks were added to the model (consistent with current best practices). Material balance calculations and statistical tests have also been added to the model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Investigating Local Carrier Dynamics in PERC Patterned CdTe Solar Cells

Remarkable progress has been achieved in CdTe photovoltaics (PVs) to further improve cell performance while reducing manufacturing costs. Researchers optimized the front contact that leads the short-circuit current density (J sc ) over 31mA/cm 2 (e.g., (Zn, Mg)O buffer layer and/or alloying CdTe with Se). Reese et al. reported an open-circuit voltage (V oc ) over 1 V with group-V doped single crystal, showing the feasibility of increasing V oc in CdTe PV that is fixed to less than 900 mV in most cases. Recent studies suggested that the V oc improvement in polycrystalline CdTe PVs requires well-passivated back contact. One possible strategy is to use CdMgTe alloy (E g > 1.8 eV), where the band-gap offset (ΔE CB ≈ 0.2 eV) reflects minority carrier electrons, thereby decreasing surface recombination. Another strategy is to utilize a stable Al 2 O 3 layer as an electron reflector; experimental works confirmed the improved performance with a conformal Al 2 O 3 layer. In this configuration, the precise control of Al 2 O 3 (≈1 nm) over the entire CdTe layer is essential because the J sc greatly depends on the tunneling current. While promising, both CdMgTe and Al 2 O 3 passivation on CdTe introduce unfavorable valence band offset that blocks the hole transport. Kephart et al. proposed a patterned passixc vation layer (≈ 20 nm Al 2 O 3 ) with point contacts (≈ 3 μm in diameter) that extract hole carriers. This configuration is similar to the passive emitter and rear contact (PERC) design that has been extensively studied in Si PVs. While remarkably high carrier lifetime and photoluminescence (> 10 X) were measured, consistent improvement in V oc and efficiency in this CdTe PERC were not yet observed. At this time, it is unclear how the surface potential is distributed in the presence of patterned Al 2 O 3 reflectors and how this additional field impacts the PV performance for Cu-doped and group-V doped CdTe PERC devices. To tackle this challenge, we develop robust nanofabrication and characterization platform to study CdTe PERC devices consisting of a patterned Al 2 O 3 layer on CdSe( 1-x )Te x (Cu-doped, GrV-doped; x = 0 to 1; CST). First Solar supplies high-quality CST materials. The dark and light I-Vs under 1-sun illumination are extracted for a series of each set of devices. We perform quantitative and qualitative PV analysis for a series of Cu-doped and Gr-V doped PERC devices, showing notably different V oc changes for GrV-doped compared to Cu-doped PERC devices. This project attempts to produce individual contacts on single grains and grain boundaries to measure lateral transport. As a model system, we use a CdSe( 1-x )Te x film on glass prepared by a colossal grain growth (CGG) technique at National Renewable Research Laboratories (NREL). Our preliminary results confirm that intergranular transport is hindered by the electrical barrier formed near grain boundaries. The PERC fabrication and the lateral transport measurement platform developed in this project can easily be applied to other types of advanced CdSe( 1-x )Te x architectures to better understand local photocarrier transport, in turn, providing the fundamental knowledge to improve the performance of CdTe PVs.

14 SOLAR ENERGY↗

DOE OSTI2022

Diffusion bonded compact heat exchanger in Inconel 740H for high temperature and high-pressure applications

It is desired to develop heat exchangers able to be operated at high temperatures (750˚C) and pressures (3636 psi) for use in advanced Brayton power cycle. Conventional materials have not had the high strength at temperature required for these applications previously, however a fairly new material Inconel 740H developed by Special Metals for the ultra-supercritical water fossil industry has shown good performance under these conditions. In further efforts to capitalize on these new high strength high temperature alloys CompRex has developed a diffusion bonding procedure capable of alloying compact high effectiveness heat exchangers that can perform under these high temperature and high-pressure conditions. Initial tests of the heat exchanger are being conducted at the University of Wisconsin using supercritical CO2 working fluid. The bonding process has been adjusted such that the strength of the bonded block has achieved over 90% yield and tensile strength of the 740H base material values. Grain size before and after bonding were measured to determine the extent of grain growth and grain diffusion across the interface. A discussion of the heat exchanger design, etching and initial tensile tests on sample bonds will be discussed.

14 SOLAR ENERGY↗

DOE OSTI2021

Designing Anion-Exchange Ionomers with Oriented Nanoscale Phase Separation at a Silver Interface

We report performance of polymer electrolyte-based energy systems is significantly impacted by transport within the electrode catalyst layer, where ionomer thin films coat catalyst particles. Proton exchange ionomer thin films have been thoroughly characterized, but few studies have critically examined anion-exchange ionomer (AEI) thin films. Further, none have reported nanoscale phase separation for hydrocarbon AEIs, which is critical to mitigate transport resistances. In this work, a set of hydrocarbon-based AEIs with nanoscale phase separation are developed from tunable block copolymer systems composed of polyisoprene (PIp) and polychloromethylstyrene (PCMS). The effect of the PIp/PCMS ratio, architecture, and thickness on the thin-film morphology of the neutral block copolymer precursors on silicon and silver substrates is investigated using grazing-incidence small-angle X-ray scattering (GISAXS) and atomic force microscopy (AFM). AEIs are prepared by quaternizing with trimethylamine or methylpiperidine and their cation-dependent morphology is characterized at 60 °C and 95% RH. A perpendicularly aligned morphology is observed on silver, while no phase separation is observed on silicon, indicating that silver-polymer interfacial interactions drive phase separation. After quaternization, dipole-dipole interactions induce some disorder, but nanoscale phase separation is still maintained. GISAXS patterns are modeled using a Unified Fit approach to understand water uptake and swelling, and recommendations for AEI design are presented.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Polymer-Grafted Nanoparticles as All-in-One Nanoplatforms

Polymer-grafted nanoparticles (PGNPs) represent a versatile class of hybrid nanomaterials, in which nanoparticle cores and tethered polymer coronas are integrated into structurally programmable building blocks. Rapid advances in nanoparticle surface functionalization and surface-initiated polymerization have enabled increasingly precise control over the nanoparticle core composition and brush architecture, greatly expanding the accessible structural and functional landscape of PGNPs. This review summarizes recent progress in the modular design and structural regulation of PGNPs, with an emphasis on nanoparticle platforms and associated surface functionalization strategies, polymer brush synthesis and architectural control, and the structure−property relationships that govern PGNP behavior. Emerging applications are further highlighted, including additive manufacturing, self-healing materials, membrane-based gas separations, and battery-related systems, where PGNPs provide unique opportunities to couple nanoscale interfacial design with macroscopic performance. Finally, future opportunities are discussed for extending PGNP concepts to increasingly complex, multifunctional, and application-oriented hybrid materials.

functional nanocomposites↗

DOE OSTI2023

Spontaneous assembly of hierarchical phases

We report the grand promise of self-assembly is the creation of target nanostructures through spontaneous molecular organization, a process that is — in principle — simpler and more scalable than laborious top-down nanofabrication methods. Yet self-assembly faces a fundamental challenge: the structures that form thermodynamically tend to minimize surface area and maximize symmetry; the most readily-accessible structures are thus quite simple. Block copolymer (BCP) self-assembly, for example, takes advantage of the chemical incompatibility along a polymer backbone to drive local phase separation; frustrated assembly leads to a nanoscale morphology whose unit cell is dictated by chain architecture. Canonical BCPs (linear chains with two blocks) form alternating lamellae and hexagonally-packed cylinders in a straightforward manner; but more exotic phases require additional control, for example directing the assembly using external forces, such as shear or chemical templates. An elegant alternative is to use synthetic methods to design more sophisticated chain architectures, which may give rise to new morphologies. An outstanding challenge is to achieve morphological control without undue synthetic burden. Sun et al. now report in Nature Nanotechnology the design and synthesis of novel triblock copolymers that give rise to structural order at multiple length scales, thereby forming complex and hierarchical nanoscale phases.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2025

A stoichiometrically conserved homologous series with infinite structural diversity

Here, we describe a compositionally guided structural evolution within a stoichiometrically conserved framework, BaSbQ 3 (Q = Te 1−x S x ), where each value of x gives rise to a distinct phase. The fundamental building blocks, A 1 (BaSbSTe 2 ) and B n (Ba n Sb n S n−1 Te 2n+1 ), were composed of modular double rocksalt slabs stacked with functional polytelluride zigzag chains, with each phase differing only in the size and assembly of these blocks. Ten compounds were synthesized that maintained a coherent chemical identity that arose from this isovalent, isoelectronic substitution of Te and S. We envision that the phase formation at a molecular level unfolds in stages of extension, termination, and assembly and propose a design concept of “anionic disparity,” where phase homologies and polytelluride hierarchical networks can be controlled by leveraging differences in anion electron affinity and sizes.

Zhao, Hengdi [Argonne National Laboratory (ANL), A↗

DOE OSTI2025

Generic Discretization Library

The GenDiL library is a collection of C++ software abstractions designed to discretize and solve partial differential equations (PDEs) for high-performance computing (HPC) applications. Its primary focus is on modern C++ generic programming, which helps ensure portability across various hardware architectures. The central idea behind the library is to provide building blocks for numerical algorithms-such as discretization methods and iteration patterns-so that domain experts can focus on the math, rather than the low-level details of hardware or implementation. By defining abstractions for data types, iteration over computational grids, and scheduling of operations, the library isolates the high-level PDE algorithms from the platform-specific optimizations needed to achieve efficient performance.

Dudouit, Yohann [Lawrence Livermore National Labor↗

DOE OSTI2021

VTK-m User's Guide (V.1.6)

High-performance computing relies on ever finer threading. Advances in processor technology include ever greater numbers of cores, hyperthreading, accelerators with integrated blocks of cores, and special vectorized instructions, all of which require more software parallelism to achieve peak performance. Traditional visualization solutions cannot support this extreme level of concurrency. Extreme scale systems require a new programming model and a fundamental change in how we design algorithms. To address these issues we created VTK-m: the visualization toolkit for multi-/many-core architectures.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2021

VTK-m User's' Guide (V.1.7)

High-performance computing relies on ever finer threading. Advances in processor technology include ever greater numbers of cores, hyperthreading, accelerators with integrated blocks of cores, and special vectorized instructions, all of which require more software parallelism to achieve peak performance. Traditional visualization solutions cannot support this extreme level of concurrency. Extreme scale systems require a new programming model and a fundamental change in how we design algorithms. To address these issues we created VTK-m: the visualization toolkit for multi-/many-core architectures. VTK-m supports a number of algorithms and the ability to design further algorithms through a top-down design with an emphasis on extreme parallelism. VTK-m also provides support for finding and building links across topologies, making it possible to perform operations that determine manifold surfaces, interpolate generated values, and find adjacencies. Although VTK-m provides a simplified high-level interface for programming, its template-based code removes the overhead of abstraction. VTK-m simplifies the development of parallel scientific visualization algorithms by providing a framework of supporting functionality that allows developers to focus on visualization operations. Consider the listings in Figure 1.1 that compares the size of the implementation for the Marching Cubes algorithm in VTK-m with the equivalent reference implementation in the CUDA software development kit. Because VTK-m internally manages the parallel distribution of work and data, the VTK-m implementation is shorter and easier to maintain. Additionally, VTK-m provides data abstractions not provided by other libraries that make code written in VTK-m more versatile.This book includes contributions from the VTK-m community including the VTK-m development team and the user community.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2022

The VTK-m Users' Guide (V.1.9)

High-performance computing relies on ever finer threading. Advances in processor technology include ever greater numbers of cores, hyperthreading, accelerators with integrated blocks of cores, and special vectorized instructions, all of which require more software parallelism to achieve peak performance. Traditional visualization solutions cannot support this extreme level of concurrency. Extreme scale systems require a new programming model and a fundamental change in how we design algorithms. To address these issues we created VTK-m: the visualization toolkit for multi-/many-core architectures. VTK-m supports a number of algorithms and the ability to design further algorithms through a top-down design with an emphasis on extreme parallelism. VTK-m also provides support for finding and building links across topologies, making it possible to perform operations that determine manifold surfaces, interpolate generated values, and find adjacencies. Although VTK-m provides a simplified high-level interface for programming, its template-based code removes the overhead of abstraction. VTK-m simplifies the development of parallel scientific visualization algorithms by providing a framework of supporting functionality that allows developers to focus on visualization operations. Consider the listings in Figure 1.1 that compares the size of the implementation for the Marching Cubes algorithm in VTK-m with the equivalent reference implementation in the CUDA software development kit. Because VTK-m internally manages the parallel distribution of work and data, the VTK-m implementation is shorter and easier to maintain. Additionally, VTK-m provides data abstractions not provided by other libraries that make code written in VTK-m more versatile.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2023

The VTK-m Users' Guide (V.2.0)

High-performance computing relies on ever finer threading. Advances in processor technology include ever greater numbers of cores, hyperthreading, accelerators with integrated blocks of cores, and special vectorized instructions, all of which require more software parallelism to achieve peak performance. Traditional visualization solutions cannot support this extreme level of concurrency. Extreme scale systems require a new programming model and a fundamental change in how we design algorithms. To address these issues we created VTK-m: the visualization toolkit for multi-/many-core architectures. VTK-m supports a number of algorithms and the ability to design further algorithms through a top-down design with an emphasis on extreme parallelism. VTK-m also provides support for finding and building links across topologies, making it possible to perform operations that determine manifold surfaces, interpolate generated values, and find adjacencies. Although VTK-m provides a simplified high-level interface for programming, its template-based code removes the overhead of abstraction. VTK-m simplifies the development of parallel scientific visualization algorithms by providing a framework of supporting functionality that allows developers to focus on visualization operations. Consider the listings in Figure 1.1 that compares the size of the implementation for the Marching Cubes algorithm in VTK-m with the equivalent reference implementation in the CUDA software development kit. Because VTK-m internally manages the parallel distribution of work and data, the VTK-m implementation is shorter and easier to maintain. Additionally, VTK-m provides data abstractions not provided by other libraries that make code written in VTK-m more versatile.

97 MATHEMATICS AND COMPUTING↗