Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “block design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

NASA experimental airborne doppler radar and real time processor for wind shear detection

The topics are presented in viewgraph form and include the following: experimental radar system capabilities; an experimental radar system block diagram; wind shear radar signal and data processor (WRSDP); WRSDP hardware architecture; WRSDP system design goals; DSP software development tools; OS-9 software development tools; WRSDP digital signal processing; WRSDP display operational modes; WRSDP division of functions; structure of WRSDP signal and data processing algorithms; and the wind shear radar flight experiment.

Schaffner, Philip H.↗
NASA NTRS1993

An in-depth probabilistic study of external tank attach ring

This report deals with conducting a probabilistic study of the external tank attach ring (ETA) used as an interface between the external tank attach struts and the solid rocket booster. The ideas were to use probabilistic distributions for material, geometric, and load properties; to calculate probabilistic margins of safety; and then to compare results against the deterministic factors of safety that were used in the actual design process. The report describes how this was done and discusses some of the road blocks and data problems that were encountered during the study and provides some conclusions. A further refinement of this study is being considered for future work which would make more direct use of finite element analysis data coupled with Monte Carlo simulation. The basic conclusion herein indicates that the probabilistic margins of safety for the cases analyzed (by use of existing data) appear to support deterministic results and actually indicate higher reliabilities.

Pizzano, Frank↗
NASA NTRS1994

Thermal/structural Tailoring of Engine Blades (T/SEAEBL). Theoretical Manual

The Thermal/Structural Tailoring of Engine Blades (T/STAEBL) system is a family of computer programs executed by a control program. The T/STAEBL system performs design optimizations of cooled, hollow turbine blades and vanes. This manual describes the T/STAEBL data block structure and system organization. The approximate analysis and optimization modules are detailed, and a validation test case is provided.

Brown, K. W.↗
NASA NTRS1995

Architecture Of A Sciencecraft To Fly Past Pluto

Two reports discuss architecture of proposed small sciencecraft carrying scientific instruments on trajectory passing near Pluto and continuing into interstellar space. Emphasizes those aspects of design pertaining to compactness, efficiency, and small mass (dry mass less than 100 kg). System block diagram of sciencecraft divided into blocks for sensors, integrated microelectronics, and motive effectors.

Price, Humphrey W.↗
NASA NTRS1996

A Hybrid Nonlinear Control Scheme for Active Magnetic Bearings

A nonlinear control scheme for active magnetic bearings is presented in this work. Magnet winding currents are chosen as control inputs for the electromechanical dynamics, which are linearized using feedback linearization. Then, the desired magnet currents are enforced by sliding mode control design of the electromagnetic dynamics. The overall control scheme is described by a multiple loop block diagram; the approach also falls in the class of nonlinear controls that are collectively known as the 'integrator backstepping' method. Control system hardware and new switching power electronics for implementing the controller are described. Various experiments and simulation results are presented to demonstrate the concepts' potentials.

Xia, F.↗
NASA NTRS1994

Reducing Interprocessor Dependence in Recoverable Distributed Shared Memory

Checkpointing techniques in parallel systems use dependency tracking and/or message logging to ensure that a system rolls back to a consistent state. Traditional dependency tracking in distributed shared memory (DSM) systems is expensive because of high communication frequency. In this paper we show that, if designed correctly, a DSM system only needs to consider dependencies due to the transfer of blocks of data, resulting in reduced dependency tracking overhead and reduced potential for rollback propagation. We develop an ownership timestamp scheme to tolerate the loss of block state information and develop a passive server model of execution where interactions between processors are considered atomic. With our scheme, dependencies are significantly reduced compared to the traditional message-passing model.

Janssens, Bob↗
NASA NTRS2007

Mission Studies for the Terrestrial Planet Finder - Occulter (TPF-O)

The 2000 decadal survey committee recommended a planet-finding telescope (TPF) capable of detecting and characterizing terrestrial planets orbiting nearby stars and of carrying out "revolutionary" astrophysics research. In response, we have carried out mission studies for TPF-O, a promising version of TPF that makes use of a "regular" telescope plus a free-flying occulter that blocks light from the target star while leaving planet light unattenuated. Our mission studies include design reference missions to carry out both planetary and general-astrophysics research. We will report on the results of these studies and describe their implications for the flight system and ground system.

Heap, S.↗
NASA NTRS2008

Innovative Applications of Laser Scanning and Rapid Prototype Printing to Rock Breakdown Experiments

We present the novel application of two technologies for use in rock breakdown experiments, i.e. close-range, ground-based 3D triangulation scanning and rapid prototype printing. These techniques aid analyses of form-process interactions across the range of scales relevant to breakdown (micron-m). This is achieved through (a) the creation of DEMs (which permit quantitative description and analysis of rock surface morphology and morphological change) and (b) the production of more realistically-shaped experimental blocks. We illustrate the use of these techniques, alongside appropriate data analysis routines, in experiments designed to investigate the persistence of fluvially-derived features in the face of subsequent wind abrasion and weathering. These techniques have a range of potential applications in experimental field and lab-based geomorphic studies beyond those specifically outlined here.

Bourke, Mary↗
NASA NTRS2013

Method for Processing Lunar Regolith Using Microwaves

A paper describes a method of using microwave heating experiments on lunar simulants to determine the mechanism that causes lunar regolith to be such an excellent microwave absorber. The experiments initially compared the effects of sharp particle edges to round particle edges on the heating curves. For most compositions, sharp particle edged samples were more effective in being heated by microwaves than round particle edged materials. However, the experiments also showed an unexpected effect for both types of particles. Upon heating the sample surface above 400 C, the sample experienced some sort of internal structure change that caused it to heat much more efficiently. This enhancement may be associated with the unique microwave volumetric heating that can produce a large temperature gradient within the sample leading to melting of some components at the center of the sample. This new effect that may also be happening in lunar regolith samples is probably the cause of the previously observed enhanced heating of a sample of lunar regolith. Properly designed microwave applicators could heat and solidify the lunar regolith to form roads and building blocks for structures needed on the Moon

Barmatz, Martin B.↗
NASA NTRSDate not supplied

Thermoplastic Composite Lunar Tower Truss Structure: Design Development and Verification Plans

The National Aeronautics and Space Administration (NASA) Space Technology and Mission Directorate (STMD) is advancing thermoplastic composite (TPC) technologies for exploration missions. The Technology Development for Exploration Applications (TDEA) project goals are to develop and mature TPC materials, designs, analyses tools and techniques, and mature manufacturing processes. This includes development of manufacturing and joining approaches relevant to space environments. To these ends TDEA endeavors toward demonstrating a TPC truss structure for a lunar tower configuration. The design, predicated on robotic assembly, uses open section truss elements fused to a joint splice plate, without a structural adhesive. This presentation details the TDEA lunar truss structure design development approach including design heritage, the requirements established, the mechanical design and analyses, and thermal analyses demonstrating structural requirements conformance, as well as planned building block verification efforts either underway or planned. The mechanical analyses show the most severe environment is a moon-quake the truss dynamic responses. The thermal analyses show the extreme cold for on-orbit welding, the window for less severe on-orbit welding, as well as the large thermal gradients on the truss. The building block approach shown includes ultrasonic welding and lap shear coupon testing on various truss element thicknesses and layups. Knockdown factor determinations due to lunar dust contamination (simulated) and effects of welding in a vacuum are presented. The most highly loaded truss joint configuration sub-element verification test matrix is outlined. Lastly, plans to build, inspect, and test a 2-bay truss representative unit cell that is 1.5 meters by 1.5 meters by 3.0 meters tall are detailed.

Lunar Tower↗
NASA NTRS1994

Asteroid 243 IDA and its satellite

A high-resolution mosaic of Ida shows a highly irregular body (roughly 56 km long), heavily covered with craters, with many interesting geological features, including grooves, blocks, chutes, dark-floored craters, and crater chains. A satellite of Ida, with a preliminary designation of 1993 (243) 1, was discovered in orbit around Ida. It is approximately 1.5 km in diameter, has an albedo and spectral reflectance not grossly different from Ida, and orbits Ida in a prograde direction with a period of roughly 20 hr. No other comparable-sized satellites have been found near Ida. New pictures of the opposite side of Ida reveal an irregular, dog-bone shape, with a prominent gouge that seems to separate Ida into two chief components. A V-shaped valley, well shown in the highest-resolution view of Ida returned in April, may mark a modest expression on the September face of the more dramatic feature on the back side. Ida's dense population of craters shows a wide diversity of morphologies, consistent with the surface having been subjected to saturated bombardment by smaller projectiles. Assuming the same projectile flux applies to Ida was used in deriving Gaspra's cratering age of about 200 m.y., and assuming that Gaspra and Ida both have the same impact strength, then the age of Ida's surface is calculated to be 1-2 b.y. This is considerably older than expected from other evidence concerning the Koronis family. Our favored explanation of Ida's satellite is that it (or a precursor satellite from which the present satellite was derived) formed during the catastrophic disruption event that formed Ida itself and formed the Koronis family of asteroids. Perhaps, instead, the satellite is a block ejected from a cratering impact. In any case, smaller blocks visible on some parts of Ida are more certain to be crater ejecta, whether or not they were ever temporary satellites.

Chapman, C. R.↗
NASA NTRSDate not supplied

Design and Analysis of A Jet Stretcher for High-Altitude Supersonic Free Jet Testing

A jet stretcher can be used to extend the region of clean flow for a test article in a supersonic free jet. The device acts to shield the article from shock waves reflected from the free jet shear layer. It can also allow for overexpanded nozzle operation through blocking shocks emanating from the nozzle lip, enlarging the potential test envelope. The FUN3D computational fluid dynamics solver was used to test a design process for developing jet stretchers. The inner surface of the axisymmetric jet stretcher was obtained from a streamline extracted from a free flight simulation around a notional test article at the intended test condition of Mach 3.2, 53,000 ft. The test article and jet stretcher were then simulated in a free jet nozzle exhaust, and the flowfield within a notional inlet aperture was compared between the installed and free flight calculations. Ambient pressure was increased until separation within the free jet nozzle finally induced disturbances at the inlet. The jet stretcher was shown to provide clean flow to the inlet at cell pressure ratios up to 2.8. A process for trimming the axisymmetric jet stretcher was also tested. This was intended to provide blockage relief for complex test articles, aiding with starting, as well as reducing weight and fabrication cost. The trimmed jet stretcher performed identically to the axisymmetric model at slightly-overexpanded conditions, but at cell pressure ratios above 1.3 allowed disturbances from the trailing edge to reach the inlet.

free jet↗
NASA NTRSDate not supplied

Design and Analysis of A Jet Stretcher for High-Altitude Supersonic Free Jet Testing

A jet stretcher can be used to extend the region of clean flow for a test article in a supersonic free jet. The device acts to shield the article from shock waves reflected from the free jet shear layer. It can also allow for overexpanded nozzle operation through blocking shocks emanating from the nozzle lip, enlarging the potential test envelope. The FUN3D computational fluid dynamics solver was used to test a design process for developing jet stretchers. The inner surface of the axisymmetric jet stretcher was obtained from a streamline extracted from a free flight simulation around a notional test article at the intended test condition of Mach 3.2, 53,000 ft. The test article and jet stretcher were then simulated in a free jet nozzle exhaust, and the flowfield within a notional inlet aperture was compared between the installed and free flight calculations. Ambient pressure was increased until separation within the free jet nozzle finally induced disturbances at the inlet. The jet stretcher was shown to provide clean flow to the inlet at cell pressure ratios up to 2.8. A process for trimming the axisymmetric jet stretcher was also tested. This was intended to provide blockage relief for complex test articles, aiding with starting, as well as reducing weight and fabrication cost. The trimmed jet stretcher performed identically to the axisymmetric model at slightly overexpanded conditions, but at cell pressure ratios above 1.3 allowed disturbances from the trailing edge to reach the inlet.

free jet↗
NASA NTRSDate not supplied

Precision in Assembled Discrete Lattice Space Structures for Next-Generation ISAM Applications

Robust autonomous robotic assembly of large-scale space structures has been a long-term and challenging goal to enable higher quality in-space communication and science instrumentation. For optical observatory support structures and antenna structures, the challenge is the strict dimensional precision requirements (generally RMS surface error) driven by the operational radiation wavelength. Early theoretical work in the area linked RMS surface error of a reflector support truss plate to the natural passive dynamic mode frequencies of the structure, as well as to the error distribution in dimensions of constituent structural elements. Prior robotic truss assembly demonstrations focused on designing ultra-high precision structural elements, joints, and robotic actuators. Recently, an alternative space structure assembly strategy based on a programmable matter approach (NASA ARMADAS) was demonstrated. This approach uses lattice building blocks (voxels) that are reversibly, mechanically joined into a bulk lattice structure by robots that locomote in and on the structure itself. Such a system can achieve high-level autonomy with low computation, robustly assemble utilizing inexpensive and imprecise robots, and efficiently build structures several orders of magnitude larger than the assembly robots. However, for instrumentation support structure applications, the resulting precision of these building block-based lattice structures is not well studied. Since they are demonstrated with many more assembly units than prior art trusses, it is unclear whether the same precision design approaches apply. In this work, we study in simulation the effects of voxel geometry, error in distribution, assembly resolution (module size), and assembly geometry on the error of both beam and plate lattice structures. While average RMS error of a plate increases with plate size, increasing plate thickness quickly collapses RMS error towards a limit that is on the order of the error of the constituent parts. We validate our models against previously published precision measurements of built systems. Results from this study will guide manufacturing precision requirements, as well as designs, for future robotically assembled structural applications and establish feasibility for different applications.

Christine E Gregg↗
NASA NTRS2012

Low-Dissipation Advection Schemes Designed for Large Eddy Simulations of Hypersonic Propulsion Systems

The 2nd-order upwind inviscid flux scheme implemented in the multi-block, structured grid, cell centered, finite volume, high-speed reacting flow code VULCAN has been modified to reduce numerical dissipation. This modification was motivated by the desire to improve the codes ability to perform large eddy simulations. The reduction in dissipation was accomplished through a hybridization of non-dissipative and dissipative discontinuity-capturing advection schemes that reduces numerical dissipation while maintaining the ability to capture shocks. A methodology for constructing hybrid-advection schemes that blends nondissipative fluxes consisting of linear combinations of divergence and product rule forms discretized using 4th-order symmetric operators, with dissipative, 3rd or 4th-order reconstruction based upwind flux schemes was developed and implemented. A series of benchmark problems with increasing spatial and fluid dynamical complexity were utilized to examine the ability of the candidate schemes to resolve and propagate structures typical of turbulent flow, their discontinuity capturing capability and their robustness. A realistic geometry typical of a high-speed propulsion system flowpath was computed using the most promising of the examined schemes and was compared with available experimental data to demonstrate simulation fidelity.

White, Jeffrey A.↗
NASA NTRS1993

A widely adaptable habitat construction system utilizing space resources

This study suggests that the cost of providing accommodations for various manned activities in space may be reduced by the extensive use of resources that are commonly found throughout the solar system. Several concepts are proposed for converting these resources into simple products with many uses. Concrete is already being considered as a possible moonbase material. Manufacturing equipment should be as small and simple as possible, which leads to the idea of molding it into miniature modules that can be produced and assembled in large numbers to create any conceivable shape. Automated equipment could build up complex structures by laying down layer after layer in a process resembling stereolithography. These tiny concrete blocks handle compression loads and provide a barrier to harmful radiation. They are joined by a web of tension members that could be made of wire or fiber-reinforced plastic. The finished structure becomes air-tight with the addition of a flexible liner. Wire can be made from the iron modules found in lunar soil. In addition to its structural role, a relatively simple apparatus can bend and weld it into countless products like chairs and shelving that would otherwise need to be supplied from Earth. Wire woven into a loose blanket could be an effective micrometeoroid shield, tiny wire compression beams could be assembled into larger beams which in turn form larger beams to create very large space-frame structures. A technology developed with lunar materials could be applied to the moons of Mars or the asteroids. To illustrate its usefulness several designs for free-flying habitats are presented. They begin with a minimal self-contained living unit called the Cubicle. It may be multiplied into clusters called Condos. These are shown in a rotating tether configuration that provides a substitute for gravity. The miniature block proposal is compared with an alternate design based on larger triangular components and a tetrahedral geometry. The overall concept may be expanded to envision city-sized self-sufficient environments where humans could confortably live their entire lives. One such proposal is the Hive. It is configured around a unique sunlight collection system that could provide all its energy needs and that could be scaled up to compensate for the reduced solar intensity at greater distances from the sun. Its outer perimeter consists of a cylindrical section mated to two conical end walls that taper inwards toward a small aperture at the center of rotation. Light collected by two huge mirrors of unusual design enters the aperture and is redirected to the inside of the cylinder. The conical end walls are shielded from direct sunlight and are designed to radiate heat into space. They are lined with air ducts that passively recirculate the atmosphere while extracting moisture by condensation. Although there is no immediate demand for spacecraft on this scale, their consideration can influence even the earliest stages of the development process.

Wykes, Harry B.↗
NASA NTRS2015

Development of Stitched Composite Structure for Advanced Aircraft

NASA has created the Environmentally Responsible Aviation Project to develop technologies which will reduce the impact of aviation on the environment. A critical aspect of this pursuit is the development of a lighter, more robust airframe that will enable the introduction of unconventional aircraft configurations. NASA and The Boeing Company are working together to develop a structural concept that is lightweight and an advancement beyond state-of-the-art composites. The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is an integrally stiffened panel design where elements are stitched together and designed to maintain residual load-carrying capabilities under a variety of damage scenarios. With the PRSEUS concept, through-the-thickness stitches are applied through dry fabric prior to resin infusion, and replace fasteners throughout each integral panel. Through-the-thickness reinforcement at discontinuities, such as along flange edges, has been shown to suppress delamination and turn cracks, which expands the design space and leads to lighter designs. The pultruded rod provides stiffening away from the more vulnerable skin surface and improves bending stiffness. A series of building blocks were evaluated to explore the fundamental assumptions related to the capability and advantages of PRSEUS panels. These building blocks addressed tension, compression, and pressure loading conditions. The emphasis of the development work has been to assess the loading capability, damage arrestment features, repairability, post-buckling behavior, and response of PRSEUS flat panels to out-of plane pressure loading. The results of this building-block program from coupons through an 80%-scale pressure box have demonstrated the viability of a PRSEUS center body for the Hybrid Wing Body (HWB) transport aircraft. This development program shows that the PRSEUS benefits are also applicable to traditional tube-andwing aircraft, those of advanced configurations, and other structures where weight and through-the-thickness strength are design considerations. An overview of the development of PRSEUS technology for commercial transport aircraft is the subject of this paper.

Jegley, Dawn↗
NASA NTRS1996

Development of Methodologies for the Estimation of Thermal Properties Associated with Aerospace Vehicles

A thermal stress analysis is an important aspect in the design of aerospace structures and vehicles such as the High Speed Civil Transport (HSCT) at the National Aeronautics and Space Administration Langley Research Center (NASA-LaRC). These structures are complex and are often composed of numerous components fabricated from a variety of different materials. The thermal loads on these structures induce temperature variations within the structure, which in turn result in the development of thermal stresses. Therefore, a thermal stress analysis requires knowledge of the temperature distributions within the structures which consequently necessitates the need for accurate knowledge of the thermal properties, boundary conditions and thermal interface conditions associated with the structural materials. The goal of this proposed multi-year research effort was to develop estimation methodologies for the determination of the thermal properties and interface conditions associated with aerospace vehicles. Specific objectives focused on the development and implementation of optimal experimental design strategies and methodologies for the estimation of thermal properties associated with simple composite and honeycomb structures. The strategy used in this multi-year research effort was to first develop methodologies for relatively simple systems and then systematically modify these methodologies to analyze complex structures. This can be thought of as a building block approach. This strategy was intended to promote maximum usability of the resulting estimation procedure by NASA-LARC researchers through the design of in-house experimentation procedures and through the use of an existing general purpose finite element software.

Scott, Elaine P.↗