Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ballistic range”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Structural damage and phase stability of Al 0.3 CoCrFeNi high entropy alloy under high temperature ion irradiation

In this study, an initially single phase high entropy alloy (HEA) Al 0.3 CoCrFeNi was irradiated by 3 MeV Au ions to a fluence of 6 × 10 15 cm –2 (~31 dpa at damage peak) at four different temperatures ranging from 250 °C to 650 °C. Transmission electron microscopy (TEM) and Atom probe tomography (APT) were employed to study the evolution of structural damage and phase stability with irradiation temperature. Al 0.3 CoCrFeNi exhibited a similar evolution of irradiation-induced defects with temperature as compared with conventional FCC alloys. At 250 °C and 350 °C, most of the visible irradiation-induced defects were faulted 1/3$\langle{111}\rangle$ dislocation loops. As the irradiation temperature increased to 500 °C, perfect 1/2$\langle{110}\rangle$ dislocation loops were observed along with the faulted loops. At the highest irradiation temperature 650 °C, only dislocation lines and networks could be observed. Regarding phase stability, the 3 MeV Au irradiation was observed to suppress the precipitation of (Ni, Al)-enriched nano clusters and the L12 ordered structure at irradiation temperatures 250 °C to 500 °C whereas precipitation of the B2 ordered structure was accelerated at 650 °C. This resulted in qualitatively opposite precipitation behavior between the ion irradiated damage region and unirradiated region at 500 °C and 650 °C. The opposite phase stability of the ion-irradiated damage region and unirradiated region at different temperatures is attributed to the competing effects of ballistic dissolution vs irradiation enhanced diffusion on precipitation.

36 MATERIALS SCIENCE↗

Color-Center Production and Formation in Electron-Irradiated Magnesium Aluminate Spinel and Ceria

Single crystals of magnesium aluminate spinel (MgAl2O4) with (100) or (110) orientations and cerium dioxide or ceria (CeO2) were irradiated by 1.0-MeV and 2.5-MeV electrons in a high fluence range. Point-defect production was studied by off-line UV-visible optical spectroscopy after irradiation. For spinel, regardless of both crystal orientation and electron energy, two characteristic broad bands centered at photon energies of 5.4 eV and 4.9 eV were assigned to F and F+ centers (neutral and singly-ionized oxygen vacancies), respectively, on the basis of available literature data. No clear differences in colour-centre formation were observed for the two crystal orientations. Using calculations of displacement cross sections by elastic collisions, these results are consistent with a very large threshold displacement energy (200 eV) for oxygen atoms at RT. A third very broad band centered at 3.7 eV might be attributed either to an oxygen hole center (V-type center) or an F2 dimer center (oxygen di-vacancy). The onset of recovery of these color centers took place at 200°C with almost full bleaching at 600°C. Activation energies (~0.3-0.4 eV) for defect recovery were deduced from the isochronal annealing data by using a first-order kinetics analysis. For ceria, a sub band-gap absorption feature peaked at ~3.1 eV was recorded for 2.5-MeV electron irradiation only. Assuming a ballistic process, we suggest that the latter defect might result from cerium atom displacement on the basis of computed cross sections.

36 MATERIALS SCIENCE↗

Full-dispersion Monte Carlo simulation of phonon transport in micron-sized graphene nanoribbons

We simulate phonon transport in suspended graphene nanoribbons (GNRs) with real-space edges and experimentally relevant widths and lengths (from submicron to hundreds of microns). The full-dispersion phonon Monte Carlo simulation technique, which we describe in detail, involves a stochastic solution to the phonon Boltzmann transport equation with the relevant scattering mechanisms (edge, three-phonon, isotope, and grain boundary scattering) while accounting for the dispersion of all three acoustic phonon branches, calculated from the fourth-nearest-neighbor dynamical matrix. We accurately reproduce the results of several experimental measurements on pure and isotopically modified samples [S. Chen et al., ACS Nano 5, 321 (2011);S. Chen et al., Nature Mater. 11, 203 (2012); X. Xu et al., Nat. Commun. 5, 3689 (2014)]. We capture the ballistic-to-diffusive crossover in wide GNRs: room-temperature thermal conductivity increases with increasing length up to roughly 100 μm, where it saturates at a value of 5800 W/m K. This finding indicates that most experiments are carried out in the quasiballistic rather than the diffusive regime, and we calculate the diffusive upper-limit thermal conductivities up to 600 K. Furthermore, we demonstrate that calculations with isotropic dispersions overestimate the GNR thermal conductivity. Zigzag GNRs have higher thermal conductivity than same-size armchair GNRs, in agreement with atomistic calculations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Multi-slit triode ion optical system with ballistic beam focusing

Multi-slit triode ion-optical systems with spherical electrodes are of interest for formation of intense focused neutral beams for plasma heating. At present, two versions of focusing multi-slit triode ion optical system are developed. The first ion optical system forms the proton beam with 15 keV energy, 140 A current, and 30 ms duration. The second ion optical system is intended for heating neutral beam injector of Tokamak Configuration Variable (TCV). The injector produces focused deuterium neutral beam with 35 keV energy, 1 MW power, and 2 s duration. In the later case, the angular beam divergence of the neutral beam is 20-22 mrad in the direction across the slits of the ion optical system and 12 mrad in the direction along the slits.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Cratering and penetration experiments in teflon targets at velocities from 1 to 7 km/s

Approximately 20 sq m of protective thermal blankets, largely composed of Teflon, were retrieved from the Long Duration Exposure Facility after the spacecraft spent approximately 5.7 years in space. Examination of these blankets revealed that they contained thousands of hypervelocity impact features ranging from micron-sized craters to penetration holes several millimeters in diameter. We conducted impact experiments to reproduce such features and to understand the relationships between projectile size and the resulting crater or penetration hole diameter over a wide range of impact velocities. Such relationships are needed to derive the size and mass frequency distribution and flux of natural and man-made particles in low-earth orbit. Powder propellant and light-gas guns were used to launch soda-lime glass spheres into pure Teflon targets at velocities ranging from 1 to 7 km/s. Target thickness varied over more than three orders of magnitude from finite halfspace targets to very thin films. Cratering and penetration of massive Teflon targets is dominated by brittle failure and the development of extensive spall zones at the target's front and, if penetrated, the target's rear side. Mass removal by spallation at the back side of Teflon targets may be so severe that the absolute penetration hole diameter can become larger than that of a standard crater. The crater diameter in infinite halfspace Teflon targets increases, at otherwise constant impact conditions, with encounter velocity by a factor of V (exp 0.44). In contrast, the penetration hole size in very thin foils is essentially unaffected by impact velocity. Penetrations at target thicknesses intermediate to these extremes will scale with variable exponents of V. Our experimental matrix is sufficiently systematic and complete, up to 7 km/s, to make reasonable recommendations for velocity-scaling of Teflon craters and penetrations. We specifically suggest that cratering behavior and associated equations apply to all impacts in which the shock-pulse duration of the projectile is shorter than that assigned a unique projectile size, provided an impact velocity is known or assumed. This calibration seems superior to the traditional ballistic-limit approach.

Horz, Friedrich↗

Hot electron transmission in metals using epitaxial NiSi{sub 2}/n-Si(111) interfaces

We have investigated hot electron transmission across epitaxial metal-disilicide/n-Si(111) interfaces using ballistic electron emission microscopy (BEEM). Different crystal orientations of epitaxial NiSi{sub 2} were grown on a Si(111) substrate using molecular beam epitaxy. The presence of different interfaces of NiSi{sub 2} on Si(111) were confirmed by high resolution transmission electron microscopy. Electrical transport measurements reveal a clear rectifying Schottky interface with a barrier height of 0.69 eV. However, using BEEM, three different regions with different transmissions and Schottky barrier heights of 0.65 eV, 0.78 eV, and 0.71 eV are found. The addition of a thin Ni film on the NiSi{sub 2} layer strongly reduces the transmission in all the three regions and interestingly, almost equalizes the transmission across them.

36 MATERIALS SCIENCE↗

Mechanical Response of Additively Manufactured Stainless Steel 304L Across a Wide Range of Loading Conditions

The mechanical response of additively manufactured (AM) stainless steel 304L has been investigated across a broad range of loading conditions, covering 11 decades of strain rate, and compared with the behaviors of traditional ingot-derived (wrought) material. In general, the AM material exhibits a greater strength and reduced ductility compared with the baseline wrought form. These differences are consistently found from quasi-static and high strain rate tests. A detailed investigation of the microstructure, the defect structure, the phase, and the composition of both forms reveals differences that may contribute to the differing mechanical behaviors. Compared with the baseline wrought material, dense AM stainless steel 304L has a more complex grain structure with substantial sub-structure, a fine dispersion of ferrite, increased dislocation density, oxide dispersions and larger amounts of nitrogen. In-situ neutron diffraction studies conducted during quasi-static loading suggest that the increased strength of AM material is due to its initially greater dislocation density. The flow strength of both forms is correlated with dislocation density through a square root dependence akin to a Taylor-like relationship. Neutron diffraction measurements of lattice strains also correlate with a crystal plasticity finite element simulations of the tensile test. Other simulations predict a significant degree of elastic and plastic anisotropy due to crystallographic texture. Hopkinson tests at higher strain rates $\dot{ε}$ = 500 and 2500 s -1 ) also show a greater strength for AM stainless steel 304L; although, the differences compared with wrought are reduced at higher strain rates. Gas gun impact tests, including reverse ballistic, forward ballistic and spall tests, consistently reveal a larger dynamic strength in the AM material. The Hugoniot Elastic Limit (HEL) of AM SS 304L exceeds that of wrought material although considerable variability is observed with the AM material. Forward ballistic testing demonstrates spall strengths of AM material (3.27 -- 3.91 GPa) that exceed that of the wrought material (2.63 -- 2.88 GPa). The Hugoniot equation-of-state for AM samples matches archived data for this metal alloy.

36 MATERIALS SCIENCE↗

Theoretical overview and modeling of the sodium and potassium atmospheres of mercury

A general theoretical overview for the sources, sinks, gas-surface interactions, and transport dynamics of sodium and potassium in the exospheric atmsophere of Mercury is given. Information for these four factors, which control the spatial distribution of these two alkali-group gases about the planet, is incorporated in numerical models. The spatial nature and relative importance of the initial source atom atmosphere and the ambient (ballistic hopping) atom atmosphere are then examined and are shown to be controlled and coupled to a great extent by the extremely large and variable solar radiation acceleration experienced by sodium and potassium as they resonantly scatter solar photons. The lateral (antisunward) transport rate of thermally accommodated sodium and potassium ambient atoms is shown to be driven by the solar radiation acceleration and, over a significant portion of Mercury's orbit about the Sun, is sufficiently rapid to be competitive with the short photoionization lifetimes for these atoms when they are located on the summit surface near or within about 30 deg of the terminator. The lateral transport rate is characterized by a migration time determined by model calculations for an ensemble of atoms initially starting at a point source on the surface (i.e., a numerical spacetime dependent Green's function). Four animations for the spacetime evolution of the sodium (or potassium) atmosphere produced by a point source on the surface are presented on a videotape format. For extended surface sources for sodium and potassium, the local column density is determined by competition between the photoionization lifetimes and the lateral transport times of atoms originating from different surface source locations. Sodium surface source fluxes (referenced to Mercury at perihelion) that are required on the sunlit hemisphere to reproduce the typically observed several megarayleighs of D2 emission-line brightness and the inferred column densities of 1-2 x 10(exp 11) atoms per sq cm range from approximately 2-5 x 10(exp 7) atoms/sq cm/sec. The sodium model is applied to study observational data that document an anticorrelation in the average sodium column density and solar radiation acceleration. Lateral transport driven by the solar radiation acceleration is shown to produce this behavior for combinations of different sources and surface accomodation coefficients. The best fit model fits to the observational data require a significant degree of thermal accommodation of the ambient sodium atoms to the surface and a source rate that decreases as an inverse power of 1.5 to 2 in heliocentric distance.

Smyth, William H.↗

Enhancement of magnetoresistance by inserting thin NiAl layers at the interfaces in Co{sub 2}FeGa{sub 0.5}Ge{sub 0.5}/Ag/Co{sub 2}FeGa{sub 0.5}Ge{sub 0.5} current-perpendicular-to-plane pseudo spin valves

We have investigated the effects of insertion of a thin NiAl layer (≤0.63 nm) into a Co{sub 2}FeGa{sub 0.5}Ge{sub 0.5} (CFGG)/Ag interface on the magnetoresistive properties in CFGG/Ag/CFGG current-perpendicular-to-plane giant magnetoresistance (CPP-GMR) pseudo spin valves (PSVs). First-principles calculations of ballistic transmittance clarified that the interfacial band matching at the (001)-oriented NiAl/CFGG interface is better than that at the (001)-Ag/CFGG interface. The insertion of 0.21-nm-thick NiAl layers at the Co{sub 2}FeGa{sub 0.5}Ge{sub 0.5}/Ag interfaces effectively improved the magnetoresistance (MR) output; the observed average and the highest MR ratio (ΔRA) are 62% (25 mΩ μm{sup 2}) and 77% (31 mΩ μm{sup 2}) at room temperature, respectively, which are much higher than those without NiAl insertion. Microstructural analysis using scanning transmission electron microscopy confirmed the existence of thin NiAl layers at the Ag interfaces with only modest interdiffusion even after annealing at 550 °C. The improvement of the interfacial spin-dependent scattering by very thin NiAl insertion can be a predominant reason for the enhancement of the MR output.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Nanoscale mapping of the W/Si(001) Schottky barrier

The W/Si(001) Schottky barrier was spatially mapped with nanoscale resolution using ballistic electron emission microscopy (BEEM) and ballistic hole emission microscopy (BHEM) using n-type and p-type silicon substrates. The formation of an interfacial tungsten silicide is observed utilizing transmission electron microscopy and Rutherford backscattering spectrometry. The BEEM and BHEM spectra are fit utilizing a linearization method based on the power law BEEM model using the Prietsch Ludeke fitting exponent. The aggregate of the Schottky barrier heights from n-type (0.71 eV) and p-type (0.47 eV) silicon agrees with the silicon band gap at 80 K. Spatially resolved maps of the Schottky barrier are generated from grids of 7225 spectra taken over a 1 μm × 1 μm area and provide insight into its homogeneity. Histograms of the barrier heights have a Gaussian component consistent with an interface dipole model and show deviations that are localized in the spatial maps and are attributed to compositional fluctuations, nanoscale defects, and foreign materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Cratering and penetration experiments in Teflon targets at velocities from 1 to 7 km/s

Approximately 20 sq m of protective thermal blankets, largely composed of Teflon, were retrieved from the Long Duration Exposure Facility (LDEF) after the spacecraft had spent approximately 5.7 years in space. Examination of these blankets revealed that they contained thousands of hypervelocity impact features ranging from micron-sized craters to penetration holes several millimeters in diameter. We conducted impact experiments in an effort to reproduce such features and to -- hopefully -- understand the relationships between projectile size and the resulting crater or penetration-hole diameter over a wide range of impact velocity. Such relationships are needed to derive the size- and mass-frequency distribution and flux of natural and man-made particles in low-Earth orbit. Powder propellant and light-gas guns were used to launch soda-lime glass spheres of 3.175 mm (1/8 inch) nominal diameter (Dp) into pure Teflon FEP targets at velocities ranging from 1 to 7 km/s. Target thickness (T) was varied over more than three orders of magnitude from infinite halfspace targets (Dp/T less than 0.1) to very thin films (Dp/T greater than 100). Cratering and penetration of massive Teflon targets is dominated by brittle failure and the development of extensive spall zones at the target's front and, if penetrated, the target's rear side. Mass removal by spallation at the back side of Teflon targets may be so severe that the absolute penetration-hole diameter (Dh) can become larger than that of a standard crater (Dc) at relative target thicknesses of Dp/T = 0.6-0.9. The crater diameter is infinite halfspace Teflon targets increases -- at otherwise constant impact conditions -- with encounter velocity by a factor of V0.44. In contrast, the penetration-hole size is very thin foils (Dp/T greater than 50) is essentially unaffected by impact velocity. Penetrations at target thicknesses intermediate to these extremes will scale with variable exponents of V. Our experimental matrix is sufficiently systematic and complete, up to 7 km/s, to make reasonable recommendations for the velocity-scaling of Teflon craters and penetrations. We specifically suggest that cratering behavior and associated equations dominate all impacts in which the shock-pulse duration of the projectile (tp) is shorter than that of the target (tt). We also demonstrate that each penetration hole from space-retrieved surfaces may be assigned a unique projectile size, provided an impact velocity is known or assumed. This calibration seems superior to the traditional ballistic-limit approach.

Hoerz, Friedrich↗

Propulsive trajectory optimization to minimize surface contamination

MOTIVATION: We present an optimization technique for propulsive vehicles that autonomously minimizes contamination during surface approach and landing. In addition to short-range hoppers, the optimization technique is also fully applicable to traditional orbit-to-surface landers. This study addresses scenarios where surface alterations from propulsion events are counterproductive or hazardous to the mission objectives. This is of immediate interest for landers (whether human or robotic), that may rely on pristine soils collected in the immediate vicinity of landing sites to accomplish science investigations, mining, or ISRU surface operations. Such missions are averse to various surface-plume interactions such as thermal scoring, physical agitation, and contamination. The capability can be applied with minimal impact to the baseline mission concept. METHODS: Optimization algorithms have been developed to calculate descent trajectories and maneuvers, thrust magnitude, and attitude for various mission cases. These parameters are determined as an optimal solution when minimizing either fuel consumption, contamination deposited at the landing site, or some weighted combination of both. Among constraints imposed on the solution, we examined pitch rate, vertical takeoff and vertical landing (VTVL) requirements, size of the contamination zone, and minimum ground clearance during flight. This tool provides unique, non-intuitive solutions and can be a valuable resource for mission planners. RESULTS: A variety of agile trajectory solutions were obtained, each yielding different reductions in landing site contamination and corresponding to only modest increases in fuel consumption. Several optimal trajectories were obtained by varying the contamination weight in the fitness function. As expected, when the contamination weight is zero, the trajectory appears close to parabolic since the optimization scheme only attempts to minimize for fuel utilization, yielding essentially, the expected ballistic trajectory. Notably for contamination weights greater than zero, trajectory inflections are observed in the descent phase, which manifests as hovering or additional, mini “pseudo hops” before the final touchdown. A trajectory inflection is characterized by arresting the majority of the spacecraft vertical velocity component at a coordinate outside of the landing target, and without violating ground clearance constraints. FUTURE WORK: Our optimization technique is ready for laboratory or field demonstrations to validate the sophisticated maneuvering solutions obtained for fuel optimization and surface preservation. An appropriate testbed would validate the optimal guidance algorithms, the navigation system, and sensor suite by emulating vehicle flight in closed loop robotic tests. Critically, these algorithms could then be ported to flight software for implementation.

surface contamination↗

Terahertz oscillations in an In{sub 0.53}Ga{sub 0.47}As submicron planar Gunn diode

The length of the transit region of a Gunn diode determines the natural frequency at which it operates in fundamental mode—the shorter the device, the higher the frequency of operation. The long-held view on Gunn diode design is that for a functioning device the minimum length of the transit region is about 1.5 μm, limiting the devices to fundamental mode operation at frequencies of roughly 60 GHz. Study of these devices by more advanced Monte Carlo techniques that simulate the ballistic transport and electron-phonon interactions that govern device behaviour, offers a new lower bound of 0.5 μm, which is already being approached by the experimental evidence that has shown planar and vertical devices exhibiting Gunn operation at 600 nm and 700 nm, respectively. The paper presents results of the first ever THz submicron planar Gunn diode fabricated in In{sub 0.53}Ga{sub 0.47}As on an InP substrate, operating at a fundamental frequency above 300 GHz. Experimentally measured rf power of 28 μW was obtained from a 600 nm long × 120 μm wide device. At this new length, operation in fundamental mode at much higher frequencies becomes possible—the Monte Carlo model used predicts power output at frequencies over 300 GHz.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Spectroscopic Chemical Analysis Methods and Apparatus

This invention relates to non-contact spectroscopic methods and apparatus for performing chemical analysis and the ideal wavelengths and sources needed for this analysis. It employs deep ultraviolet (200- to 300-nm spectral range) electron-beam-pumped wide bandgap semiconductor lasers, incoherent wide bandgap semiconductor lightemitting devices, and hollow cathode metal ion lasers. Three achieved goals for this innovation are to reduce the size (under 20 L), reduce the weight [under 100 lb (.45 kg)], and reduce the power consumption (under 100 W). This method can be used in microscope or macroscope to provide measurement of Raman and/or native fluorescence emission spectra either by point-by-point measurement, or by global imaging of emissions within specific ultraviolet spectral bands. In other embodiments, the method can be used in analytical instruments such as capillary electrophoresis, capillary electro-chromatography, high-performance liquid chromatography, flow cytometry, and related instruments for detection and identification of unknown analytes using a combination of native fluorescence and/or Raman spectroscopic methods. This design provides an electron-beampumped semiconductor radiation-producing method, or source, that can emit at a wavelength (or wavelengths) below 300 nm, e.g. in the deep ultraviolet between about 200 and 300 nm, and more preferably less than 260 nm. In some variations, the method is to produce incoherent radiation, while in other implementations it produces laser radiation. In some variations, this object is achieved by using an AlGaN emission medium, while in other implementations a diamond emission medium may be used. This instrument irradiates a sample with deep UV radiation, and then uses an improved filter for separating wavelengths to be detected. This provides a multi-stage analysis of the sample. To avoid the difficulties related to producing deep UV semiconductor sources, a pumping approach has been developed that uses ballistic electron beam injection directly into the active region of a wide bandgap semiconductor material.

Hug, William F.↗

SOFT X-RAY TEMPERATURE TIDAL DISRUPTION EVENTS FROM STARS ON DEEP PLUNGING ORBITS

One of the puzzles associated with tidal disruption event candidates (TDEs) is that there is a dichotomy between the color temperatures of a few × 10{sup 4} K for TDEs discovered with optical and UV telescopes and the color temperatures of a few × 10{sup 5}–10{sup 6} K for TDEs discovered with X-ray satellites. Here, we propose that high-temperature TDEs are produced when the tidal debris of a disrupted star self-intersects relatively close to the supermassive black hole, in contrast to the more distant self-intersection that leads to lower color temperatures. In particular, we note from simple ballistic considerations that greater apsidal precession in an orbit is the key to closer self-intersection. Thus, larger values of β, the ratio of the tidal radius to the pericenter distance of the initial orbit, are more likely to lead to higher temperatures of more compact disks that are super-Eddington and geometrically and optically thick. For a given star and β, apsidal precession also increases for larger black hole masses, but larger black hole masses imply a lower temperature at the Eddington luminosity. Thus, the expected dependence of the temperature on the mass of the black hole is non-monotonic. We find that in order to produce a soft X-ray temperature TDE, a deep plunging stellar orbit with β > 3 is needed and a black hole mass of ≲5 × 10{sup 6}M{sub ⊙} is favored. Although observations of TDEs are comparatively scarce and are likely dominated by selection effects, it is encouraging that both expectations are consistent with current data.

79 ASTRONOMY AND ASTROPHYSICS↗

Kinetics of spin relaxation in quantum wires and channels: Boundary spin echo and formation of a persistent spin helix

In this paper we use a spin kinetic equation to study spin-polarization dynamics in one-dimensional (1D) wires and 2D channels. The spin kinetic equation is valid in both diffusive and ballistic spin transport regimes and therefore is more general than the usual spin drift-diffusion equations. In particular, we demonstrate that in infinite 1D wires with Rashba spin-orbit interaction the exponential spin-relaxation decay can be modulated by an oscillating function. In the case of spin relaxation in finite length 1D wires, it is shown that an initially homogeneous spin polarization spontaneously transforms into a persistent spin helix. We find that a propagating spin-polarization profile reflects from a system boundary and returns back to its initial position similarly to the reflectance of sound waves from an obstacle. The Green's function of the spin kinetic equation is derived for both finite and infinite 1D systems. Moreover, we demonstrate explicitly that the spin relaxation in specifically oriented 2D channels with Rashba and Dresselhaus spin-orbit interactions of equal strength occurs similarly to that in 1D wires of finite length. Finally, a simple transformation mapping 1D spin kinetic equation into the Klein-Gordon equation with an imaginary mass is found thus establishing an interesting connection between semiconductor spintronics and relativistic quantum mechanics.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Shape Effect Analysis of Aluminum Projectile Impact on Whipple Shields

The informed design with respect to hypervelocity collisions involving micrometeoroid and orbital debris (MMOD) is influential to the success of space missions. For an orbit comparable to that of the International Space Station, velocities for MMOD can range from 1 to 15 km/s, with an average velocity around 10 km/cu s. The high energy released during collisions at these speeds can result in damage to a spacecraft, or worst-case, loss of the spacecraft, thus outlining the importance of methods to predict the likelihood and extent of damage due to an impact. Through experimental testing and numerical simulations, substantial work has been conducted to better understand the effects of hypervelocity impacts (HVI) on spacecraft systems and shields; however, much of the work has been focused on spherical impacting particles. To improve environment models for the analysis of MMOD, a large-scale satellite break-up test was performed at the Arnold Engineering and Development Complex to better understand the varied impactor geometries that could be generated from a large impact. As a part of the post-experiment analysis, an undertaking to characterize the irregular fragments generated is currently being performed by the University of Florida under the management of NASA's Orbital Debris Program Office at Johnson Space Center (JSC). DebriSat was a representative, modern LEO satellite that was catastrophically broken up in a HVI test. The test chamber was lined with a soft-catch system of foam panels that captured the fragments after impact. Initial predictions put the number of fragments larger than 2mm generated from the HVI at roughly 85,000. The number of fragments thus far extracted from the foam panels has exceeded 100,000, with that number continuously increasing. The shapes of the fragments vary dependent upon the material. Carbon-fiber reinforced polymer pieces, for instance, are abundantly found as thin, flat slivers. The characterization of these fragments with respect to their mass, size, and material composition needs to be summarized in a form that can be used in MMOD analysis. The mechanism that brings these fragment traits into MMOD analysis is through ballistic limit equations (BLE) that have been developed largely for a few types of materials1. As a BLE provides the failure threshold for a shield or spacecraft component based on parameters such as the projectile impact velocity and size, and the target's materials, thickness, and configuration, it is used to design protective shields for spacecraft such as Whipple shields (WS) to an acceptable risk level. The majority of experiments and simulations to test shields and validate BLEs have, heretofore, largely used spheres as the impactor, not properly reflecting the irregular shapes of MMOD. This shortfall has motivated a numerical impact analysis study of HVI involving non-spherical geometries to identify key parameters that environment models should provide.

Carrasquilla, Maria J.↗

Compositional Impact of Io Volcanic Emissions on Jupiter's Magnetosphere and the Icy Galilean Moons

The magnetospheric ion population of Jupiter is dominated by the 1000 kg/s of iogenic material constantly ejected by IO volcanism as neutral gas (approx. 1 kg/s goes out as high speed dust grains), subsequent atmospheric losses to the IO torus, and radial transport of torus ions throughout the magnetosphere. As that magnetosphere is greatly distended in radial size by the iogenic plasma loading, so are surfaces of the other Galilean moons also significantly, and perhaps even dominantly, affected by iogenic plasma bombardment, e.g. at the level up to 0.2 kg/s heavy ions (mostly O and S) onto Europa as per local plasma ion measurements. In comparison, cometary impacts onto IO deliver about 0.02 kg/s of impact ejecta to Europa via ballistic transfer through the Jupiter system. The magnetosphere of this system operates as a powerful engine to produce and transport ions from the IO source to the surfaces of these other moons, and any future orbiter missions to these moons must account for surface distributions of the iogenic material and its chemical effects before real assessments can be made of sensible chemical materials otherwise arising from primordial formation and subsequent evolution of these moons. This is a fundamental problem of space weathering that must be addressed for all planetary bodies with thin atmospheres and direct surface exposure to their space plasma environments. Long-standing debates from Galileo Orbiter measurements about the origins of hydrate sulfates at Europa present examples of this problem, as to whether the sulfates arise from oceanic minerals or from iogenic sulfur chemistry. Any orbiter or landed mission to Europa for astrobiological investigations would further need to separate the potential chemical biosignatures of life or its precursors from the highly abundant background of iogenic material. Although no single ion carries a tag identifying it as of iogenic or other origin, the elemental abundance distributions of ions to be measured throughout the jovian magnetosphere and in the local moon environments can act as tracers if we know from direct measurements and models the distributions at the mostly likely sources, i.e. at IO. However, our knowledge of these abundances are very limited from earlier in-situ and remote measurements, mainly confined to major (S, O) and some minor (Na, K, Cl) species with abundances at or above a few percent relative to O. Future in-situ plasma measurements by the planned Jupiter Europa Orbiter and Jupiter Ganymede Orbiter missions should extend the abundance coverage to minor and even trace elemental species. For Europa astrobiological investigations it is also important to specify iogenic inputs and surface processing of isotopic species. We discuss the range of abundance distributions arising from models for IO hot volcanic emissions, and from the subsequent dynamics of ion injection, magnetospheric transport, and icy moon surface bombardment.

Cooper, John↗