An application of Falkner's surface-loading method to predictions of hinge-moment parameters for swept-back wings
Explore the source record for details and available documents.
LOAD DISTRIBUTION - WINGS, SWEPTBACK↗
SEARCH · Engineering Papers
Results for “Wing loading”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Performance, Loads and Stability of Heavy Lift Tiltrotors
Summaries of rotor performance are presented for a 124,000-lb Large Civil Tilt Rotor (LCTR) design, along with isolated-rotor and fully-coupled wing/rotor aeroelastic stability. A major motivation of the present research is the effect of size on rotor dynamics. Simply scaling up existing rotor designs to the vehicle size under study would result in unacceptable rotor weight. The LCTR was the most promising of several large rotorcraft concepts produced by the NASA Heavy Lift Rotorcraft Systems Investigation. It was designed to carry 120 passengers for 1200 nm, with performance of 350 knots at 30,000 ft altitude. Design features included a low-mounted wing and hingeless rotors, with a very low cruise tip speed of 350 ft/sec. The LCTR was sized by the'RC code developed by the U. S. Army Aeroflightdynamics Directorate. The rotor was then optimized using the CAMRAD II comprehensive analysis code. The blade and wing structures were designed by Pennsylvania State University to meet the rotor loads calculated by CAMRAD II and wing loads required for certification. Aeroelastic stability was confirmed by further CAMRAD II analysis, based on the optimized rotor and wing designs.
Acree, Cecil W., Jr.↗
Effects of airplane flexibility on wing bending strains in rough air
Some results on the effects of wing flexibility on wing bending strains as determined from flight tests of a Boeing B-29 and a Boeing B-47A airplane in rough air are presented. Results from an analytical study of the flexibility effects on the B-29 wing strains are compared with the experimental results. Both the experimental and calculated results are presented as frequency-response functions of the bending strains at various spanwise wing stations to gust disturbances. In addition, some indirect evidence of the effect of spanwise variations in turbulence on the response of the B-47A airplane is presented.
LOADS, GUST - WINGS↗
Means for controlling aerodynamically induced twist
A control mechanism which provides active compensation for aerodynamically induced twist deformation of high aspect ratio wings consists of a torque tube, internal to each wing and rigidly attached near the tip of each wing, which is moved by an actuator located in the aircraft fuselage. As changes in the aerodynamic loads on the wings occur the torque tube is rotated to compensate for the induced wing twist.
Elber, W.↗
Strain-gage bridge calibration and flight loads measurements on a low-aspect-ratio thin wing
Strain-gage bridges were used to make in-flight measurements of bending moment, shear, and torque loads on a low-aspect-ratio, thin, swept wing having a full depth honeycomb sandwich type structure. Standard regression analysis techniques were employed in the calibration of the strain bridges. Comparison of the measured loads with theoretical loads are included.
Peele, E. L.↗
Residual strength and crack propagation tests on C-130 airplane center wings with service-imposed fatigue damage
Fourteen C-130 airplane center wings, each containing service-imposed fatigue damage resulting from 4000 to 13,000 accumulated flight hours, were tested to determine their fatigue crack propagation and static residual strength characteristics. Eight wings were subjected to a two-step constant amplitude fatigue test prior to static testing. Cracks up to 30 inches long were generated in these tests. Residual static strengths of these wings ranged from 56 to 87 percent of limit load. The remaining six wings containing cracks up to 4 inches long were statically tested as received from field service. Residual static strengths of these wings ranged from 98 to 117 percent of limit load. Damage-tolerant structural design features such as fastener holes, stringers, doublers around door cutouts, and spanwise panel splices proved to be effective in retarding crack propagation.
Snider, H. L.↗
A method for the design of sweptback wings warped to produce specified flight characteristics at supersonic speeds
One of the problems connected with the sweptback wing is the difficulty of controlling the location of the center of pressure and hence the pitching moment. A method is presented for designing a wing to be self-trimming at a given set of flight conditions. Concurrently, the spanwise distribution of load on the wing is made to be approximately elliptical, in an effort to maintain low wing drag.
Tucker, Warren A↗
Gust Load Alleviation Control and Gust Estimation for a High Aspect Ratio Wing Wind Tunnel Model
This paper presents the gust load alleviation (GLA) study of the aspect ratio 13.5 Common Research Model (CRM) wind-tunnel model. This study details the design of the GLA controller in preparation for wind-tunnel testing in the Transonic Dynamics Tunnel at NASA Langley Research Center. An aeroservolastic (ASE) model was first reduced using a model reduction method that takes advantage of the sinusoidal steady-state response. Then, the reduced model was used to design an extended-state Kalman filter which estimates the states and the sinusoidal gust input. The GLA control was then derived using the optimal control solution to a multi-objective cost function. The results of the GLA controller indicate a 75.6% reduction in wing-root strain while maintaining robust stability margins. The final paper will include performance under sub-optimal conditions, e.g., sensor noise, uncertainty in gust frequency, etc..
Christopher Forte↗
Gust Load Alleviation Control and Gust Estimation for a High Aspect Ratio Wing Wind Tunnel Model
This paper presents the gust load alleviation (GLA) study of the aspect ratio 13.5 Common Research Model (CRM) wind-tunnel model. This study details the design of the GLA controller in preparation for wind-tunnel testing in the Transonic Dynamics Tunnel at NASA Langley Research Center. An aeroservolastic (ASE) model is first reduced using a model reduction method that takes advantage of the sinusoidal steady-state response. Then, the reduced model is used to design an extended-state Kalman filter which estimates the states and the sinusoidal gust input. The GLA control is then derived using the optimal control solution to a multi-objective cost function. The results of the GLA controller indicate a 69.07% reduction in wing-root strain without sensor noise and 68.45% reduction with sensor noise, while maintaining robust stability margins. An adaptive GLA controller is developed for uncertain gust frequency and shows a 71.03% reduction in wing root strain compared to the non-adaptive control reduction of just 39.19%.
Christopher Forte↗
Analytical Fuselage and Wing Weight Estimation of Transport Aircraft
A method of estimating the load-bearing fuselage weight and wing weight of transport aircraft based on fundamental structural principles has been developed. This method of weight estimation represents a compromise between the rapid assessment of component weight using empirical methods based on actual weights of existing aircraft, and detailed, but time-consuming, analysis using the finite element method. The method was applied to eight existing subsonic transports for validation and correlation. Integration of the resulting computer program, PDCYL, has been made into the weights-calculating module of the AirCraft SYNThesis (ACSYNT) computer program. ACSYNT has traditionally used only empirical weight estimation methods; PDCYL adds to ACSYNT a rapid, accurate means of assessing the fuselage and wing weights of unconventional aircraft. PDCYL also allows flexibility in the choice of structural concept, as well as a direct means of determining the impact of advanced materials on structural weight. Using statistical analysis techniques, relations between the load-bearing fuselage and wing weights calculated by PDCYL and corresponding actual weights were determined.
Chambers, Mark C.↗
Gust-tunnel Tests to Determine Influence of Airfoil Section Characteristics on Gust-load Factors
Explore the source record for details and available documents.
LOADS, GUST - WINGS↗
Modeling damaged wings: Element selection and constraint specification
The NASTRAN analytical program was used for structural design, and no problems were anticipated in applying this program to a damaged structure as long as the deformations were small and the strains remained within the elastic range. In this context, NASTRAN was used to test three-dimensional analytical models of a damaged aircraft wing under static loads. A comparison was made of calculated and experimentally measured strains on primary structural components of an RF-84F wing. This comparison brought out two sensitive areas in modeling semimonocoque structures. The calculated strains were strongly affected by the type of elements used adjacent to the damaged region and by the choice of multipoint constraints sets on the damaged boundary.
Stronge, W. J.↗
Elevated-temperature effects on strain gages on the YF-12A wing
A general study is made of the effects of structural heating on calibrated-strain-gage load measurements on the wing of a supersonic airplane. The primary emphasis is on temperature-induced effects as they relate to slope changes and thermal shifts of the applied load/strain relationships. These effects are studied by using the YF-12A airplane, a structural computer model, and subsequent analyses. Such topics as the thermal environment of the structure, the variation of load paths at elevated temperature, the thermal response characteristics of load equations, elevated-temperature load-measurement approaches, the thermal calibration of wings, and the correlation of strains are discussed. Ways are suggested to measure loads with calibrated strain gages in the supersonic environment.
Jenkins, J. M.↗
Analysis of high aspect ratio jet flap wings of arbitrary geometry.
Paper presents a design technique for rapidly computing lift, induced drag, and spanwise loading of unswept jet flap wings of arbitrary thickness, chord, twist, blowing, and jet angle, including discontinuities. Linear theory is used, extending Spence's method for elliptically loaded jet flap wings. Curves for uniformly blown rectangular wings are presented for direct performance estimation. Arbitrary planforms require a simple computer program. Method of reducing wing to equivalent stretched, twisted, unblown planform for hand calculation is also given. Results correlate with limited existing data, and show lifting line theory is reasonable down to aspect ratios of 5.
Lissaman, P. B. S.↗
Numerical study of the effects of icing on fixed and rotary wing performance
The sectional and total aerodynamic load characteristics and performance degradation of swept wings and helicopter rotors have been studied using a three-dimensional, compressible Navier-Stokes solver. Correlations of predictions with experimental data for swept wings with and without leading-edge ice formation show the ability of the present computational technique to accurately predict both the distributed surface pressures and integrated sectional loads. The leading-edge flow separation and reattachment on the wing surface associated with the leading-edge ice are also captured well showing a vortex formation and the spanwise migration of the flow inside the separated flow region. In the case of the helicopter rotors in hover, the rotor thrust loss and the torque penalties due to the leading-edge ice formation are numerically demonstrated.
Kwon, Oh J.↗
Effect at High Subsonic Speeds of Fuselage Forebody Strakes on the Static Stability and Vertical-Tail-Load Characteristics of a Complete Model Having a Delta Wing
A wind-tunnel investigation at high subsonic speeds has been conducted to determine the effect of fuselage forebody strakes on the static stability and the vertical-tail-load characteristics of an airplane-type configuration having a delta wing. The tests were made at Mach numbers from 0.60 to 0.92 corresponding to Reynolds numbers from 3.0 x 10(exp 6) to 4.2 x 10(exp 6), based on the wing mean aerodynamic chord, and at angles of attack from approximately -2 to 24 deg. The strakes provided improvements in the directional stability characteristics of the wing-fuselage configuration which were reflected in the characteristics of the complete configuration in the angle-of-attack range where extreme losses in directional stability quite often occur. It was also found that the strakes, through their beneficial effect on the wing-fuselage directional stability, reduced the vertical-tail load per unit restoring moment at high angles of attack. The results also indicated that, despite the inherent tendency for strakes to produce a pitch-up, acceptable pitching-moment characteristics can be obtained provided the strakes are properly chosen and used in conjunction with a wing-body-tail configuration characterized by increasing stability with increasing lift.
Polamus, Edward C.↗
Calculated effect of various types of flap on take-off over obstacles
In order to determine whether or not flaps could be expected to have any beneficial effect on take-off performance, the distances required to take off and climb to an altitude of 50 feet were calculated for hypothetical airplanes, corresponding to relatively high-speed types and equipped with several types of flap. The types considered are the Fowler wing, the Hall wing, the split flap, the balanced split flap, the plain flap, and the external-airfoil flap. The results indicate that substantial reductions in take-off distance are possible through the use of flaps, provided that the proper flap angle corresponding to a given set of conditions is used. The best flap angle for taking off varies inversely as power loading and, to a much smaller extent, varies inversely with wing loading. Apparently, the best take-off characteristics are provided by the type of device in which the flap forms an extension to the main wing as in the case of the Fowler wing and the external-airfoil flap.
Wetmore, J W↗
Preliminary aerodynamic design considerations for advanced laminar flow aircraft configurations
Modern composite manufacturing methods have provided the opportunity for smooth surfaces that can sustain large regions of natural laminar flow (NLF) boundary layer behavior and have stimulated interest in developing advanced NLF airfoils and improved aircraft designs. Some of the preliminary results obtained in exploratory research investigations on advanced aircraft configurations at the NASA Langley Research Center are discussed. Results of the initial studies have shown that the aerodynamic effects of configuration variables such as canard/wing arrangements, airfoils, and pusher-type and tractor-type propeller installations can be particularly significant at high angles of attack. Flow field interactions between aircraft components were shown to produce undesirable aerodynamic effects on a wing behind a heavily loaded canard, and the use of properly designed wing leading-edge modifications, such as a leading-edge droop, offset the undesirable aerodynamic effects by delaying wing stall and providing increased stall/spin resistance with minimum degradation of laminar flow behavior.
Johnson, Joseph L., Jr.↗