Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WOOD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Emissions of particulate matter, carbon monoxide and nitrogen oxides from the residential burning of waste paper briquettes and other fuels

Highlights: • The first attempt to report emission of key air pollutants from waste paper briquettes. • Burning of paper briquettes emitted relatively high CO and NO{sub x} concentration. • Burning of paper briquettes emitted PM with large average particle size. • Waste paper could be recycled as briquettes for domestic use like other common fuels. Using waste paper as fuel for domestic heating is a beneficial recycling option for small island developing states where there are lacks of resources for energy and waste treatment. However, there are concerns about the impact of air pollutants emitted from the burning of the self-made paper briquettes as household air pollution is recognised as the greatest environmental risk for human. In this study, combustion tests were carried out for paper briquettes made in one Pacific island and three commercial fuels in Australia including wood briquettes, kindling firewood and coal briquettes in order to: 1) characterise the emissions of three criteria air pollutants including particulate matters, CO and NO{sub x} including their emission factors (EF) from the tested fuels; and 2) compare the EFs among the tested fuels and with others reported in the literature. The results showed that waste paper briquettes burned quickly and generated high temperature but the heat value is relatively low. Paper briquettes and coal briquettes produced higher CO concentration than the others while paper briquettes generated the highest NO{sub x} level. Only PM{sub 2.5} concentration emitted from paper briquettes was similar to kindling firewood and lower than wood briquettes. Burning of paper briquettes and wood briquettes produced particulate matter with large average count median diameter (72 and 68 nm) than coal briquette and kindling firewood (45 and 51 nm). The EFs for CO, NO{sub x} and PM{sub 2.5} of paper briquettes were within the range of EFs reported in this study as well as in the literature. Overall, the results suggested that using paper briquettes as fuel for domestic heating will not likely to generate higher level of three major air pollutants compared to other traditional fuels.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2018

Biocomposite Fiber-Matrix Treatments that Enhance In-Service Performance Can Also Accelerate End-of-Life Fragmentation and Anaerobic Biodegradation to Methane

Biodegradable resins can enhance the environmental sustainability of wood-plastic composites (WPCs) by enabling methane (CH{sub 4}) recovery via anaerobic digestion (AD). An under appreciated step in biocomposite AD is the role of cracking and fragmentation due to moisture uptake by the wood fiber (WF) fraction. Here, we use batch microcosms to simulate AD at end-of-life and to assess the effects of fiber-matrix treatments used to retard in-service moisture uptake. The composites evaluated were injection molded poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) with WF (0, 20%) using two fiber-matrix compatibilization treatments: (1) hydrophobic silane treatment of the wood fiber and (2) grafting of hydrophilic maleic anhydride groups to the PHBV matrix. Both treatments accelerated rates of mass loss and CH{sub 4} production by a factor of 1.2–2.3 compared to neat PHBV. The fragmentation rate, as measured by mass loss, increased significantly for treated samples compared to untreated samples. A ranking of test samples from lowest to highest rates of mass loss gave the following sequence: neat PHBV ≈ maleated PHBV < PHBV plus untreated WF < maleated PHBV plus untreated WF < PHBV plus silane-treated WF. Compared to the untreated samples, maleic anhydride treatment increased the mass loss rate by 30%, and silane treatment increased the mass loss rate by 92%. Onset of cracking in silane-treated composites was observed at 2 weeks (using X-ray micro-computed tomography). At the same time, solid mass loss and CH{sub 4} production peaked, implicating cracking and physical disintegration as the rate-limiting step for accelerated anaerobic degradation. When modified to account for bioplastic matrix degradation, a previously derived moisture-induced damage model could predict the onset of composite fragmentation at end-of-life. These results are significant for design of bio-WPCs and demonstrate that treatments designed to improve in-service performance can also improve end-of-life options.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Self-reported health impacts of do-it-yourself air cleaner use in a smoke-impacted community

Smoke exposure from wildfires or residential wood burning for heat is a public health problem for many communities. Do-It-Yourself (DIY) portable air cleaners (PACs) are promoted as affordable alternatives to commercial PACs, but evidence of their effect on health outcomes is limited. Pilot test an evaluation of the effect of DIY PAC usage on self-reported symptoms, and investigate barriers and facilitators of PAC use, among members of a tribal community that routinely experiences elevated concentrations of fine particulate matter (PM 2.5 ) from smoke. We conducted studies in Fall 2021 (“wildfire study”; N = 10) and Winter 2022 (“wood stove study”; N = 17). Each study included four sequential one-to-two-week phases: 1) initial, 2) DIY PAC usage ≥8 h/day, 3) commercial PAC usage ≥8 h/day, and 4) air sensor with visual display and optional PAC use. We continuously monitored PAC usage and indoor/outdoor PM 2.5 concentrations in homes. Concluding each phase, we conducted phone surveys about participants’ symptoms, perceptions, and behaviors. We analyzed symptoms associated with PAC usage and conducted an analysis of indoor PM 2.5 concentrations as a mediating pathway using mixed effects multivariate linear regression. We categorized perceptions related to PACs into barriers and facilitators of use. No association was observed between PAC usage and symptoms, and the mediation analysis did not indicate that small observed trends were attributable to changes in indoor PM 2.5 concentrations. Small sample sizes hindered the ability to draw conclusions regarding the presence or absence of causal associations. DIY PAC usage was low; loud operating noise was a barrier to use. This research is novel in studying health effects of DIY PACs during wildfire and wood smoke exposures. Such research is needed to inform public health guidance. Recommendations for future studies on PAC use during smoke exposure include building flexibility of intervention timing into the study design.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2017

Heavy Metal-Free Tannin from Bark for Sustainable Energy Storage

A novel renewable cathode made from earth abundant, low-cost materials can contribute to the intermittent storage needs of renewable energy-based society. In this work, we report for the first-time tannin from Nature as a cathode material. Our approach exploits the charge storage mechanism of the redox active quinone moiety. Tannins extracted from tree bark using environmental friendly aqueous solvents have the highest phenol content (5.56 mol g -1 ) among all the natural phenolic biopolymers, 5000 times higher than lignin. Tannins coupled with a conductive polymer polypyrrole acquire high specific capacitance values of 370 F g -1 at 0.5 A g -1 as well as excellent rate performance of 196 F g -1 at 25 A g -1 . Additionally, we employed carbonized wood as an electrode substrate to produce a sustainable electrochemical device with dramatically improved performance compared to conventional devices. The high surface area provided by the well-aligned, cellular porosity of wood-derived substrate combined with the high mobility of ions and electrons in the carbonized cell walls and deposited tannin can achieve an areal capacitance of 4.6 F cm -2 at 1 mA cm -2 , which is 1.5 times higher than activated wood carbon.

09 BIOMASS FUELS↗
DOE OSTI2019

Coal-Filler-Based Thermoplastic Composites as Construction Materials: A New Sustainable End-Use Application

This paper investigates coal’s viability as an alternative filler to wood flour in Wood Plastic Composites (WPCs) – a class of materials used in building applications in lieu of pressure-treated wood. Coal Plastic Composites (CPCs) were fabricat-ed with 15 – 60 wt.% coal combined with high density polyethylene and their physical (mechanical, water absorption and metal leaching) and chemical (oxidative degradation and flammability) properties were compared with commercial WPCs. In addition, mass and energy balances (10 tonne/hr basis) and life cycle analyses (60 wt.% filler and 1 tonne ba-sis) were conducted on CPCs and WPCs to assess environmental impact during manufacturing. At 60 wt.%, CPCs had a higher flexural strength, slower oxidative degradation and burn rate, and lower water absorption in comparison to com-mercial WPCs, suggesting better performance and stability in building applications. Furthermore, CPC manufacturing showed 44% lower greenhouse gas emissions and 62% less energy usage in comparison with WPC. These results indi-cate that direct utilization of coal as a filler in construction composite applications may yield lower cost products with lower associated emissions and energy demand compared to existing WPC materials, potentially yielding a more sustain-able end-use for coal than current uses such as power production.

Coal Plastic Composites, Wood Plastic Composites, ↗
DOE OSTI2025

Life Cycle Cost Analysis of Prestressed Concrete Poles Subjected to Wind, Surges, and Waves

Prestressed concrete (PC) poles are becoming popular choices to support coastal power transmission systems. However, the existing literature does not offer a detailed analysis of the effectiveness of PC poles in terms of long-term vulnerabilities and the direct and indirect costs. This is due to (1) lack of fragility models for PC poles and (2) lack of probabilistic wind, storm surge, and wave models in coastal settings. In this study, we address these gaps through a series of Monte Carlo simulations to estimate fragility of PC poles as a function of age and hazard (wind, surges, and waves) intensity, and the development of a probabilistic hazard model based on 10,000 years of synthetic tropical cyclone data. The probabilistic hazard model is used in conjunction with high-resolution hydrodynamic models to generate realizations of coastal wind, storm surges, and waves for the Louisiana and Mississippi coasts. A comprehensive life cycle cost analysis for a service life of 70 years considering direct and indirect losses is conducted to compare the performance of a transmission line located in Pascagoula, Mississippi, when wood poles are replaced by PC poles. Results showed that aging has a minor effect on the reliability of PC poles, highlighting the advantages of replacing wood poles with PC poles, especially in coastal areas. In addition, PC poles are significantly more cost-effective compared with wood poles over their life cycle, leading to an estimated saving of $11.55 million (68.17% reduction). The results of this study provide key insight to inform decision-making processes to keep the coastal power grids resilient and cost-effective against future storm hazards.

natural disasters↗
DOE OSTI2019

Gene Regulation Shifts Shed Light on Fungal Adaption in Plant Biomass Decomposers

ABSTRACT Fungi dominate the recycling of carbon sequestered in woody biomass. This process of organic turnover was first evolved among “white rot” fungi that degrade lignin to access carbohydrates and later evolved multiple times toward more efficient strategies to selectively target carbohydrates—“brown rot.” The brown rot adaption was often explained by mechanisms to deploy reactive oxygen species (ROS) to oxidatively attack wood structures. However, its genetic basis remains unclear, especially in the context of gene contractions of conventional carbohydrate-active enzymes (CAZYs) relative to white rot ancestors. Here, we hypothesized that these apparent gains in brown rot efficiency despite gene losses were due, in part, to upregulation of the retained genes. We applied comparative transcriptomics to multiple species of both rot types grown across a wood wafer to create a gradient of progressive decay and to enable tracking temporal gene expression. Dozens of “decay-stage-dependent” ortho-genes were isolated, narrowing a pool of candidate genes with time-dependent regulation unique to brown rot fungi. A broad comparison of the expression timing of CAZY families indicated a temporal regulatory shift of lignocellulose-oxidizing genes toward early stages in brown rot compared to white rot, enabling the segregation of oxidative treatment ahead of hydrolysis. These key brown rot ROS-generating genes with iron ion binding functions were isolated. Moreover, transcription energy was shifted to be invested on the retained GHs in brown rot fungi to strengthen carbohydrate conversion. Collectively, these results support the hypothesis that gene regulation shifts played a pivotal role in brown rot adaptation. IMPORTANCE Fungi dominate the turnover of wood, Earth’s largest pool of aboveground terrestrial carbon. Fungi first evolved this capacity by degrading lignin to access and hydrolyze embedded carbohydrates (white rot). Multiple lineages, however, adapted faster reactive oxygen species (ROS) pretreatments to loosen lignocellulose and selectively extract sugars (brown rot). This brown rot “shortcut” often coincided with losses (>60%) of conventional lignocellulolytic genes, implying that ROS adaptations supplanted conventional pathways. We used comparative transcriptomics to further pursue brown rot adaptations, which illuminated the clear temporal expression shift of ROS genes, as well as the shift toward synthesizing more GHs in brown rot relative to white rot. These imply that gene regulatory shifts, not simply ROS innovations, were key to brown rot fungal evolution. These results not only reveal an important biological shift among these unique fungi, but they may also illuminate a trait that restricts brown rot fungi to certain ecological niches.

plant biomas↗
DOE OSTI2015

Downregulation of GAUT12 in Populus deltoides by RNA silencing results in reduced recalcitrance, increased growth and reduced xylan and pectin in a woody biofuel feedstock

The inherent recalcitrance of woody bioenergy feedstocks is a major challenge for their use as a source of second-generation biofuel. Secondary cell walls that constitute the majority of hardwood biomass are rich in cellulose, xylan, and lignin. The interactions among these polymers prevent facile accessibility and deconstruction by enzymes and chemicals. Plant biomass that can with minimal pretreatment be degraded into sugars is required to produce renewable biofuels in a cost-effective manner. The following are the results: GAUT12/IRX8 is a putative glycosyltransferase proposed to be involved in secondary cell wall glucuronoxylan and/or pectin biosynthesis based on concomitant reductions of both xylan and the pectin homogalacturonan (HG) in Arabidopsis irx8 mutants. Two GAUT12 homologs exist in Populus trichocarpa, PtGAUT12.1 and PtGAUT12.2. Knockdown expression of both genes simultaneously has been shown to reduce xylan content in Populus wood. We tested the proposition that RNA interference (RNAi) downregulation of GAUT12.1 alone would lead to increased sugar release in Populus wood, that is, reduced recalcitrance, based on the hypothesis that GAUT12 synthesizes a wall structure required for deposition of xylan and that cell walls with less xylan and/or modified cell wall architecture would have reduced recalcitrance. Using an RNAi approach, we generated 11 Populus deltoides transgenic lines with 50 to 67% reduced PdGAUT12.1 transcript expression compared to wild type (WT) and vector controls. Ten of the eleven RNAi lines yielded 4 to 8% greater glucose release upon enzymatic saccharification than the controls. The PdGAUT12.1 knockdown (PdGAUT12.1-KD) lines also displayed 12 to 52% and 12 to 44% increased plant height and radial stem diameter, respectively, compared to the controls. Knockdown of PdGAUT12.1 resulted in a 25 to 47% reduction in galacturonic acid and 17 to 30% reduction in xylose without affecting total lignin content, revealing that in Populus wood as in Arabidopsis, GAUT12 affects both pectin and xylan formation. Finally, analyses of the sugars present in sequential cell wall extracts revealed a reduction of glucuronoxylan and pectic HG and rhamnogalacturonan in extracts from PdGAUT12.1-KD lines.

09 BIOMASS FUELS↗
DOE OSTI2016

Analysis of Joist Masonry Moisture Content Monitoring

BSC TO5 Task 7.2 Analysis of Joist Masonry Moisture Content Monitoring House - Lawrence, MA 01840 This work involved the field monitoring of embedded wood joist ends in a solid brick building in zone 5A that was retrofitted with interior insulation. Eleven joists throughout the building (which have a variety of orientations, exposures, and masonry wall types) were monitored for wood MCs at the embedded joist ends and for temperatures and RHs within the joist pocket. Indoor and outdoor conditions were also recorded. Results were collected for 28 months (December 2012-April 2015). One limitation was that the renovation was still ongoing; limited wintertime construction heating and no permanent occupancy were factors. Much of the building experienced cold interior temperatures (e.g., construction heating) during the winters. These were not typical interior heating set points. Because the building was essentially unoccupied, no significant interior moisture was generated. These boundary conditions are not normal service conditions. Overall, the RHs and MCs measured in joist pockets were higher than recommended for longterm durability. Many of the joist pockets had sustained conditions of 100% RH, and many wood MCs were in the 25%-35% range for extended periods. Typical guidance includes: (1) MCs lower than 20% are safe, and (2) decay fungi become active at MCs higher than 28%. ASHRAE xi 160 analysis showed that high RH levels coincided with temperatures that were high enough to support mold growth for most of the monitoring period (60%-70% of the hours) in most joists. However, no damage was seen at the joist ends when the instrumentation was installed or when a joist end sample was removed. This suggests that dense, old-growth framing might be able to survive these MCs without damage. Orientation has a significant effect on RH and MC levels: solar heating and drying kept all southfacing joist MCs well within the safe range. The east and west orientations had mixed results: some were in the safe range, but others exceeded the 20% MC level. The north side joists consistently had the highest MCs. Almost all the joists showed seasonal rises and falls; MC and RH conditions were higher during the summer and lower during the winter. This indicates the temperature gradient caused moisture to be driven inward during the summer. MC plots with driving rain showed no discernable correlations. In the parts of the building that had significant wintertime heating, many joists showed a drop in MC that coincided with the addition of heat, even after insulation and air sealing were installed. The joist ends showed a repeated pattern of MC measurements at their upper and lower ends. The lower joist end was consistently wetter than the upper joist end, which can be attributed to contact with the masonry pocket, gravity drainage of bulk water to the bottom of the pocket, greater drying at the top of the beam or deeper embedment at the bottom of the beam, and a larger air pocket at the top of the beam. The north-facing insulated and uninsulated joist ends were compared; a significant or consistent MC or RH difference was not seen between these cases. All three joist pockets essentially remained at a constant 100% RH.

Array↗
NASA NTRS1997

A Study of the Electrical Properties and Mineralogy of the Surface of Venus

This annual progress report is a list of papers on a study of the electrical properties and mineralogy of the surface of Venus. These papers were written by P. I. Wood and C. A. Robinson. Titles include: Subduction on the margins of coronae on Venus: Evidence from radiothermal emissivity measurements; The weathering process on Venus takes 2-3 hundred million years: Evidence from radiothermal emissivity signatures at coronae; SO2 and CH4 levels in the Venusian atmosphere, measured by Pioneer Venus: Caused by plinian-style volcanic activity at Maat Mons; Magellan reveals Venus; Recent volcanic activity on Venus: Evidence from radiothermal emissivity signatures; Occurrences of low-emissivity surface material at low altitudes on Venus: A window to the past; Must the Venus surface material contain hematite; Rock weathering on the surface of Venus; Comment on "The Rate of Pyrite Decomposition on the Surface of Venus-by J. A. Wood, and R. Brett; and Complex dielectric constants and magnetic permeabilities of mineral mixtures-by De Roo, R.D, C.A. Robinson, F.T. Ulaby, and J.A. Wood.

Wood, John A.↗
NASA NTRS2019

Effects of Topography on Tropical Forest Structure Depend on Climate Context

Topography affects abiotic conditions which can influence the structure, function, and dynamics of ecological communities. An increasing number of studies have demonstrated biological consequences of fine-scale topographic heterogeneity but we have a limited understanding of how We merged high-resolution (1 sq. meter) data on topography and canopy height derived from airborne lidar with ground-based data from 15 forest plots in Puerto Rico distributed along a precipitation gradient spanning ca. 800 to 3,500 mm yr(exp -1). Ground-based data included species composition, estimated above-ground biomass (AGB), and two key functional traits (wood density and leaf mass per area, LMA) that reflect resource-use strategies and a trade-off between hydraulic safety and hydraulic efficiency. We used hierarchical Bayesian models to evaluate how the interaction between topography climate is related to metrics of forest structure (i.e., canopy height and AGB), as well as taxonomic and functional alpha- and beta-diversity. Fine-scale topography (characterized with the topographic wetness index, TWI) significantly affected forest structure and the strength (and in some cases direction) of these effects varied across the precipitation gradient. In all plots, canopy height increased with topographic wetness but the effect was much stronger in dry compared to wet forest plots. In dry forest plots, topographically wetter microsites also had higher levels of AGB but in wet forest plots, topographically drier microsites had higher AGB. Fine-scale topography influenced functional composition but had only weak or non-significant effects on taxonomic and functional alpha- and beta-diversity. For instance, community-weighted wood density followed a similar pattern to AGB across plots. We also found a marginally significant association between variation of wood density and topographic heterogeneity that depended on climate context. Synthesis: The effects of fine-scale topographic heterogeneity on tropical forest structure and composition depend on the climate context. Our study demonstrates how a stronger integration of topographic heterogeneity across precipitation gradients could improve estimates of forest structure and biomass, and may provide insight to the ways that topography might mediate species responses to drought and climate change.

Tropical dry forest↗
DOE OSTI2016

Chapter 8 - Challenges and Opportunities for International Trade in Forest Biomass. In the book Mobilisation of Forest Bioenergy in the Boreal and Temperate Biomes.

In an effort to reduce fossil fuel consumption, the use of woody biomass for heat and power generation is growing. Key destination markets will be countries within the European Union (EU), particularly the United Kingdom (UK), the Netherlands, Denmark, and Belgium. While demand from Asia (particularly South Korea and Japan) will also increase, it will continue to play a secondary role. Across the EU, adoption of sustainability criteria for forest biomass based on the Renewable Energy Directive (RED) 2009/28/EC or similar criteria is likely. In the UK, the largest market for traded wood pellets, such criteria have already been proposed. As of 2015, only forest biomass that achieves at least a 60% reduction in GHG emissions relative to the EU fossil fuel electricity average can be used for bioenergy production, and proof of Sustainable Forest Management (SFM) is required. In the Netherlands, the energy industry and non-governmental organizations achieved principal agreement on sustainability criteria for solid biomass, but issues of compliance testing and monitoring must still be addressed. In Flemish Belgium, the sustainability requirements for bioliquids may soon be applied to woody biomass. In Denmark, a voluntary industry agreement is set to ensure that all bioenergy production by 2019 is conducted sustainably. At present, internationally traded wood pellets from temperate and boreal biomes originate primarily from the United States (US), Canada, and Russia. Among these, Canada offers large stretches of SFM-certified forests, but the US Southeast has seen the strongest increase in wood pellet production and export in recent years. The expansion of pellet production in the US Southeast is mainly linked to available forest inventory (pulpwood in particular)and the competitive advantage gained by the relative proximity to demand markets in the EU. In addition to the mobilization barriers observed in supply chains at the local and national scale, limitations in the supply of forest biomass for international trade will be influenced by regulatory measures that could restrict the trade of specific feedstock fractions.

09 BIOMASS FUELS↗
DOE OSTI2016

Computed Tomography by Combining Transmission and Scatter Radiography Methods

In 2015, approximately 13 billion tons of freight was transported in the US, roughly 40 tons per person. 40% of all freight on a ton-mile basis will be transported by railroads. Class I railroads have approximately 140,000 miles (224,000 km) of railroad track across the country. Approximately 3,200 crossties per mile secure the rails at the proper gauge, transmit loads to the ballast, and prevent lateral and longitudinal shifting. Wood crossties can fail in many ways including rotting, breaking, cracking, and splitting. Developing new technologies to inspect these crossties are necessary to help maintain and ensure safe railroad operations. The Georgetown Railroad Equipment Company partnered with the University of Florida to develop the Aurora Xi X-ray backscatter inspection system. This system generates 2D backscatter images at 25 mph to detect weakness in wood crossties long before the internal degradation is visible on the tie surface. The railroad industry has a need for a high-speed high resolution 3D inspection method to inspect approximately 20 million newly fabricated railroad crossties per year. Currently new ties are not radiographically inspected to reject internal flaws and verify that rot prevention treatments have adequately penetrated into the crosstie. Current spiral scan computed tomography (CT) systems are not designed for the 100 cm/s to 400 cm/s speed of a wood crosstie production line. Building on the technology developed for the 2D Aurora Xi system, a new 3D fan-beam inspection system and CT method is being developed. A previous scatter CT method by Arsenault and Hussein required moving the Xray source to many positions, averaging the X-ray spectra, and ignoring the Compton scatter change of energy. The proposed design and method combines transmission and scatter radiography in all directions without moving or rotating the X-ray sources or detectors. (authors)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Characterization of the thermophilic xylanase Fsa02490Xyn from the hyperthermophile Fervidibacter sacchari belonging to glycoside hydrolase family 10

Fervidibacter sacchari is an aerobic hyperthermophile belonging to the phylum Armatimonadota that degrades a variety of polysaccharides. Its genome encodes 117 enzymes with one or more annotated glycoside hydrolase (GH) domain, but the roles of these putative GHs in polysaccharide catabolism are poorly defined. Here, we describe one F. sacchari enzyme encoding a GH10 domain, Fsa02490Xyn, that was previously shown to be active on Miscanthus, oat β-glucan, and beech-wood xylan, with optimal activity at 90-100 °C. We show that Fsa02490Xyn is also active on birch-wood xylan and gellan gum. The pH range on beech-wood xylan was 4.5 to 9.5 (pHopt 7.0-8.0). Fsa024940Xyn had a Km of 2.375 mm, Vmax of 1250 μm·min-1, and kcat/Km of 1.259 × 104 s-1·m-1 when using a para-nitrophenyl-?-xylobioside assay. A phylogenetic analysis of GH10 family enzymes revealed a large clade of enzymes from diverse members of the class Fervidibacteria, including Fsa02490Xyn and a second enzyme from F. sacchari, with apparent horizontal gene transfer within Fervidibacteria and between Fervidibacteria and thermophilic Bacillota. This study establishes Fsa02490Xyn as a hyperthermophilic GH10 enzyme with endo-β-1,4-xylanase activity and identifies a large clade of homologous GH10 enzymes within the class Fervidibacteria. Impact statement The depolymerization of xylan at high temperatures is important because this process limits the degradation of polysaccharides in nature and the synthesis of biofuels from plant wastes. Our study is also important because F. sacchari is one of only a few cultivated members of the Armatimonadota, which are polysaccharide-degradation specialists.

Armatimonadota↗
DOE OSTI2016

Multi-spatial analysis of forest residue utilization for bioenergy

The alternative energy sector is expanding quickly in the USA since passage of the Energy Policy Act of 2005 and the Energy Independence and Security Act of 2007. Increased interest in wood-based bioenergy has led to the need for robust modeling methods to analyze woody biomass operations at landscape scales. However, analyzing woody biomass operations in regions like the US Inland Northwest is difficult due to highly variable terrain and wood characteristics. We developed the Forest Residue Economic Assessment Model (FREAM) to better integrate with Geographical Information Systems and overcome analytical modeling limitations. FREAM analyzes wood-based bioenergy logistics systems and provides a modeling platform that can be readily modified to analyze additional study locations. We evaluated three scenarios to test the FREAM's utility: a local-scale scenario in which a catalytic pyrolysis process produces gasoline from 181 437 Mg yr-1 of forest residues, a regional-scale scenario that assumes a biochemical process to create aviation fuel from 725 748 Mg yr-1 of forest residues, and an international scenario that assumes a pellet mill producing pellets for international markets from 272 155 Mg yr-1 of forest residues. The local scenario produced gasoline for a modeled cost of $22.33 GJ-1*, the regional scenario produced aviation fuel for a modeled cost of $35.83 GJ-1 and the international scenario produced pellets for a modeled cost of $10.51 GJ-1. Results show that incorporating input from knowledgeable stakeholders in the designing of a model yields positive results.

09 BIOMASS FUELS↗
DOE OSTI2013

Integrating a process-based ecosystem model with Landsat imagery to assess impacts of forest disturbance on terrestrial carbon dynamics: Case studies in Alabama and Mississippi

Forest ecosystems in the southern United States are dramatically altered by three major disturbances: timber harvesting, hurricane, and permanent land conversion. Understanding and quantifying effects of disturbance on forest carbon, nitrogen, and water cycles is critical for sustainable forest management in this region. In this study, we introduced a process-based ecosystem model for simulating forest disturbance impacts on ecosystem carbon, nitrogen, and water cycles. Based on forest mortality data classified from Landsat TM/ETM + images, this model was then applied to estimate changes in carbon storage using Mississippi and Alabama as a case study. Mean annual forest mortality rate for these states was 2.37%. Due to frequent disturbance, over 50% of the forest land in the study region was less than 30 years old. Forest disturbance events caused a large carbon source (138.92 Tg C, 6.04 Tg C yr -1 ; 1 Tg = 10 12 g) for both states during 1984–2007, accounting for 2.89% (4.81% if disregard carbon storage changes in wood products) of the total forest carbon storage in this region. Large decreases and slow recovery of forest biomass were the main causes for carbon release. Forest disturbance could result in a carbon sink in few areas if wood product carbon was considered as a local carbon pool, indicating the importance of accounting for wood product carbon when assessing forest disturbance effects. The legacy effects of forest disturbance on ecosystem carbon storage could last over 50 years. Lastly, this study implies that understanding forest disturbance impacts on carbon dynamics is of critical importance for assessing regional carbon budgets.

58 GEOSCIENCES↗
DOE OSTI2024

Dissimilar material joining of densified superwood to aluminum by adhesive bonding

Abstract Superwood is a densified wood product that shows promise as a lightweight and renewable alternative for metallic materials. In order for this high-performance new material to be used in multi-material products, it must be able to be joined with other major materials. For example, joining superwood to aluminum would provide a key enabling technology for its use in automotive components since aluminum is presently a major lightweight material for such applications. In this paper, a methacrylate-based adhesive has been identified to provide high lap shear strength (7.5 MPa) for aluminum-to-superwood joints. The aluminum-to-superwood samples were prepared with different amounts of pre-polishing to create openings to the pores in the superwood so adhesive could penetrate into them and create a mechanical interlock, in addition to the hydrogen/chemical bonding at the surface between the methyl methacrylate (MMA) in methacrylate-based adhesive and the cellulose in superwood. For aluminum samples, a thin layer (typically a few nanometers) of oxide film on the surfaces provides hydrogen/chemical bond to MMA structure in the adhesive layer. The failure strength of the superwood-to-aluminum joint sample is about 50% higher than that of natural wood to natural wood joint sample and comparable to that of aluminum-to-aluminum joint sample.

Automation & Control Systems↗