Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WIRES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Polarimetry and Schlieren diagnostics of underwater exploding wires

Nondisturbing laser-probing polarimetry (based on the Faraday and Kerr effects) and Schlieren diagnostics were used in the investigation of underwater electrical wire explosion. Measuring the polarization plane rotation angle of a probing laser beam due to the Faraday effect allows one to determine an axially resolved current flowing through the exploding wire, unlike commonly used current probes. This optical method of measuring current yields results that match those obtained using a current viewing resistor within an accuracy of 10%. The same optical setup allows simultaneous space-resolved measurement of the electric field using the Kerr effect. It was shown that the maximal amplitude of the electric field in the vicinity of the high-voltage electrode is approx80 kV/cm and that the radial electric field is <1 MV/cm during the wire explosion. Finally, it was shown that the use of Schlieren diagnostics allows one to obtain qualitatively the density distribution behind the shock wave front, which is important for the determination of the energy transfer from the discharge channel to the generated water flow.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Observations of the long distance exploding wire restrike mechanism

An exploding wire restrike mechanism is applied to create plasma paths up to 9 m in length. The mechanism uses enameled copper wires in a 5 to 10 kV/m region of average electric field (AEF). This relatively low AEF restrike mechanism appears to be linked to the formation of plasma beads along the wire's length. Voltage traces, measurement of relative emitted light intensity and photographs are presented at AEFs below, inside and above the identified restrike region.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Controlling Cu–Sn mixing so as to enable higher critical current densities in RRP ® Nb 3 Sn wires

Dipole magnets for the proposed Future Circular Collider (FCC) demand specifications significantly beyond the limits of all existing Nb 3 Sn wires, in particular a critical current density (J c ) of more than 1500 A mm -2 at 16 T and 4.2 K with an effective filament diameter (D eff ) of less than 20 μm. The restacked-rod-process (RRP ® ) is the technology closest to meeting these demands, with a J c (16 T) of up to 1400 A mm -2 , residual resistivity ratio > 100, for a sub-element size D s of 58 μm (which in RRP ® wires is essentially the same as D eff ). An important present limitation of RRP ® is that reducing the sub-element size degrades J c to as low as 900 A mm -2 at 16 T for D s = 35 μm. To gain an understanding of the sources of this J c degradation, we have made a detailed study of the phase evolution during the Cu–Sn 'mixing' stages of the wire heat treatment that occur prior to Nb 3 Sn formation. Using extensive microstructural quantification, we have identified in this paper the critical role that the Sn–Nb–Cu ternary phase (Nausite) can play. The Nausite forms as a well-defined ring between the Sn source and the Cu/Nb filament pack, and acts as an osmotic membrane in the 300 °C–400 °C range—greatly inhibiting Sn diffusion into the Cu/Nb filament pack while supporting a strong Cu counter-diffusion from the filament pack into the Sn core. This converts the Sn core into a mixture of the low melting point (408 °C) η phase (Cu 6 Sn 5 ) and the more desirable ε phase (Cu 3 Sn), which decomposes at 676 °C. After the mixing stages, when heated above 408 °C towards the Nb 3 Sn reaction, any residual η liquefies to form additional irregular Nausite on the inside of the membrane. All Nausite decomposes into NbSn 2 on further heating, and ultimately transforms into coarse-grain (and often disconnected) Nb 3 Sn which has little contribution to current transport. Understanding this critical Nausite reaction pathway has allowed us to simplify the mixing heat treatment to only one stage at 350 °C for 400 h which minimizes Nausite formation while encouraging the formation of the higher melting point ε phase through better Cu–Sn mixing. Finally, at a D s of 41 μm, the Nausite control heat treatment increases the J c at 16 T by 36%, reaching 1300 A mm -2 (i.e. 2980 A mm -2 at 12 T), and moving RRP ® closer to the FCC targets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Quantum dot to quantum wire transition of m-plane GaN islands

Structural studies of m-plane GaN quantum dots and quantum wires are presented. A shape transition responsible for the evolution of quantum dots into quantum wires is put in evidence and shown to depend on the amount of material deposited. In addition, it is established that vertical correlation of successive nanostructure planes may also induce the dot-wire shape transition. Consistent with theoretical predictions, it is proposed that the shape transition results from an elastic energy minimization process made possible by an easy adatom diffusion along [11-20] direction.

36 MATERIALS SCIENCE↗

Current shunting and formation of stationary shock waves during electric explosions of metal wires in air

Results of experiments on the generation of shock waves during electric explosions of fine copper and tungsten wires in air are analyzed. The generation mechanism of stationary shock wave by a plasma piston formed during the shunting breakdown of the electrode gap in the course of a wire explosion is investigated. The role of structural elements of such discharges, such as the core, corona, and wire environment, is analyzed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Enhanced Second Generation (2G) High Temperature Superconducting (HTS) wire for Electric Motor Applications

This project focused on the development of a revolutionary Second Generation (2G) high temperature superconducting (HTS) wire engineered specifically to meet the requirements for a new generation of high temperature superconducting electric machines. This novel design combined a roll-to-roll irradiation process to enhance the performance of the HTS wire in the presence of strong magnetic fields (improved flux pinning) with an innovative process to incorporate multiple HTS layers within a single 2G wire.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Difficult Removal of Retrievable IVC Filters: A Description of the 'Double-Wire Restraining' Technique

We describe our experience with the use of the 'double-wire restraining' technique to assist in the removal of two retrievable inferior vena cava filters: one had been misplaced in the right brachiocephalic vein with apex perforation of the vessel wall, and the second filter had migrated cephalad to straddle across both renal veins. The 'double-wire restraining' technique consists of two stiff-shaft Glidewires (Terumo, Somerset, NJ) placed through the same introducer sheath and positioned on opposite sides of the filter. Both wires restrain the filter at the tip of the sheath as the sheath is advanced, thus allowing the operator to reposition the filter. This report details how this technique was used to realign two malpositioned filters and reposition the filter apices from their extravascular location, thus exposing them for ensnarement.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Radiofrequency Guide Wire Recanalization of Venous Occlusions in Patients with Malignant Superior Vena Cava Syndrome

Fibrotic central venous occlusions in patients with thoracic malignancy and prior radiotherapy can be impassable with standard catheters and wires, including the trailing or stiff end of a hydrophilic wire. We report two patients with superior vena cava syndrome in whom we successfully utilized a radiofrequency guide wire (PowerWire, Baylis Medical, Montreal, Quebec, Canada) to perforate through the occlusion and recanalize the occluded segment to alleviate symptoms.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Radiofrequency Wire Recanalization of Chronically Thrombosed TIPS

Radiofrequency (RF) guide wires have been applied to cardiac interventions, recanalization of central venous thromboses, and to cross biliary occlusions. Herein, the use of a RF wire technique to revise chronically occluded transjugular intrahepatic portosystemic shunts (TIPS) is described. In both cases, conventional TIPS revision techniques failed to revise the chronically thrombosed TIPS. RF wire recanalization was successfully performed through each of the chronically thrombosed TIPS, demonstrating initial safety and feasibility in this application.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

MRI-guided Wire Localization Surgical Biopsy in an Adolescent Patient with a Difficult to Diagnose Case of Lymphoma

A 17-year-old previously healthy female presented with a progressive soft tissue infiltrative process involving the neck and thorax. Extensive diagnostic evaluation including multiple imaging, laboratory, and biopsy studies was nondiagnostic. Due to an urgent need to establish a diagnosis and several previous nondiagnostic biopsies, she was referred to interventional radiology for MRI-guided wire localization immediately prior to open surgical biopsy. Under general anesthesia, wires were placed in the areas of increased T2 signal within the bilateral splenius capitis muscles using intermittent MRI-guidance followed by immediate surgical biopsy down to the wires. Pathology confirmed the diagnosis of diffuse large B-cell lymphoma.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Radiofrequency Wire Recanalization of Chronically Occluded Venous Stents: A Retrospective, Single-Center Experience in 15 Patients

Introduction: Chronically occluded venous stents may be difficult to salvage, necessitating multiple approaches and adjunctive techniques. Radiofrequency wires have been used to cross chronic obstructions in a variety of settings. Herein, radiofrequency wire recanalization (RFWR) of chronically occluded venous stents is presented. Materials and Methods: Fifteen patients (8 males; 7 females) aged 23–74 years (median 42 years) underwent prior venous stenting in the setting of venous occlusions. Seven had an underlying coagulopathy, three had May–Thurner syndrome, three had provoked deep venous thrombosis, one had a dialysis fistula, and one had pacer leads in situ. All indwelling venous stents were chronically occluded and symptomatic. Out of 15 patients, 13 (87%) had iliocaval venous stents, while two (13%) had superior vena cava and/or upper extremity venous stents. After failing conventional and blunt recanalization techniques, RFWR was performed to traverse the chronic occlusions. Technical success and complications were recorded. Results: Fifteen patients underwent 19 procedures. Twelve patients underwent one procedure, two patients had two procedures, and one patient had three procedures. RFWR alone was used in 12/19 (63%) procedures, while 7/19 (37%) required adjunctive sharp recanalization techniques. Technical success or crossing of the occlusion with flow restoration through the occluded segments was achieved in 17/19 (89%). One major and one minor complication occurred. Conclusion: Radiofrequency wire recanalization is an effective adjunct to revise chronically occluded venous stents, potentially increasing procedural success in challenging cases.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Structural-Phase States of Fe–Cu and Fe–Ag Bimetallic Particles Produced by Electric Explosion of Two Wires

X-ray phase analysis, transmission electron microscopy, and X-ray microanalysis were used to examine the structural-phase states of Fe–Cu and Fe–Ag bimetallic nanoparticles. The nanoparticles were obtained by the electric explosion of two twisted metal wires in argon atmosphere. It was demonstrated that the nanoparticles have the structure of Janus particles. Presence of the Janus particle structure in the samples indicates formation of binary melt under conditions of combined electric explosion of two wires. Phases based on supersaturated solid solutions were not found in the examined samples. The data obtained allow arguing that it is possible to achieve uniform mixing of the two-wire explosion products under the described experiment conditions.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Fabrication of Copper-Rich Cu-Al Alloy Using the Wire-Arc Additive Manufacturing Process

An innovative wire-arc additive manufacturing (WAAM) process is used to fabricate Cu-9 at. pct Al on pure copper plates in situ, through separate feeding of pure Cu and Al wires into a molten pool, which is generated by the gas tungsten arc welding (GTAW) process. After overcoming several processing problems, such as opening the deposition molten pool on the extremely high-thermal conductive copper plate and conducting the Al wire into the molten pool with low feed speed, the copper-rich Cu-Al alloy was successfully produced with constant predesigned Al content above the dilution-affected area. Also, in order to homogenize the as-fabricated material and improve the mechanical properties, two further homogenization heat treatments at 1073 K (800 °C) and 1173 K (900 °C) were applied. The material and mechanical properties of as-fabricated and heat-treated samples were compared and analyzed in detail. With increased annealing temperatures, the content of precipitate phases decreased and the samples showed gradual improvements in both strength and ductility with little variation in microstructures. The present research opened a gate for in-situ fabrication of Cu-Al alloy with target chemical composition and full density using the additive manufacturing process.

36 MATERIALS SCIENCE↗

Advanced Process Possibilities in Friction Crush Welding of Aluminum, Steel, and Copper by Using an Additional Wire

Joining sheet metal can be problematic using traditional friction welding techniques. Friction crush welding (FCW) offers a high speed process which requires a simple edge preparation and can be applied to out-of-plane geometries. In this work, an implementation of FCW was employed using an additional wire to weld sheets of EN AW5754 H22, DC01, and Cu-DHP. The joint is formed by bringing together two sheet metal parts, introducing a wire into the weld zone and employing a rotating disk which is subject to an external force. The requirements of the welding preparation and the fundamental process variables are shown. Thermal measurements were taken which give evidence about the maximum temperature in the welding center and the temperature in the periphery of the sheet metals being joined. The high welding speed along with a relatively low heat input results in a minimal distortion of the sheet metal and marginal metallurgical changes in the parent material. In the steel specimens, this FCW implementation produces a fine grain microstructure, enhancing mechanical properties in the region of the weld. Aluminum and copper produced mean bond strengths of 77 and 69 pct to that of the parent material, respectively, whilst the steel demonstrated a strength of 98 pct. Using a wire offers the opportunity to use a higher-alloyed additional material and to precisely adjust the additional material volume appropriate for a given material alignment and thickness.

36 MATERIALS SCIENCE↗

Use of wire grid polarizers with liquid crystal display for large-volume stereolithography

Spatial light modulators that use liquid crystal devices (LCDs) to pattern ultraviolet light for vat polymerization suffer from a few limitations: limited range of wavelengths that can be patterned, low damage threshold for incoming light, and low efficiency of light transmission. A monochrome LCD can more efficiently transmit useful wavelengths of light for stereolithography (365–405 nm) than a color LCD, but it still contains two absorptive film polarizers that suffer from the aforementioned limitations. Wire grid polarizers reflect rather than absorb the blocked polarizations of light, resulting in a higher intensity damage threshold. They can also polarize lower wavelength light that is limited only by the wire pitch. In this work, this research investigates the effects of replacing an LCD’s film polarizers with wire grid polarizers to enable polarization and patterning of high intensity UV light, resulting in shorter curing times and the ability to print a wider range of stereolithography feedstocks.

42 ENGINEERING↗

Experimental studies on heat transfer and friction factor characteristics of Al{sub 2}O{sub 3}/water nanofluid in a circular pipe under laminar flow with wire coil inserts

In this paper, fully developed laminar flow convective heat transfer and friction factor characteristics of Al{sub 2}O{sub 3}/water nanofluid flowing through a uniformly heated horizontal tube with and without wire coil inserts is presented. For this purpose, Al{sub 2}O{sub 3} nanoparticles of 43 nm size were synthesized, characterized and dispersed in distilled water to form stable suspension containing 0.1% volume concentration of nanoparticles. The Nusselt number in the fully developed region were measured and found to increase by 12.24% at Re = 2275 for plain tube with nanofluid compared to distilled water. Two wire coil inserts made of stainless steel with pitch ratios 2 and 3 were used which increased the Nusselt numbers by 15.91% and 21.53% respectively at Re = 2275 with nanofluid compared to distilled water. The better heat transfer performance of nanofluid with wire coil insert is attributed to the effects of dispersion or back-mixing which flattens the temperature distribution and make the temperature gradient between the fluid and wall steeper. The measured pressure loss with the use of nanofluids is almost equal to that of the distilled water. The empirical correlations developed for Nusselt number and friction factor in terms of Reynolds/Peclet number, pitch ratio and volume concentration fits with the experimental data within {+-}15%. (author)

42 ENGINEERING↗

DSP methods for correcting dispersion and pulse width effects during pulsed wire measurements

Measuring a magnetic field by applying electric current to a wire in a magnetic field for a short duration and recording the resulting travelling wave is referred to as the pulsed wire method. This technique is beneficial when other methods for acquiring magnetic field data are not feasible, e.g. small aperture limit of a Hall probe to measure an insertion device, or it can be used as a complement to other techniques. Data collected during pulsed wire measurements require corrections due to dispersion of the travelling wave and averaging effects of the current pulse duration. As a result, a flexible method for correcting dispersion has been developed using all pass digital filtering techniques and deconvolution is used to correct for pulse width averaging. Implementing the correction method is described along with the results of measuring a reference magnet and a 2.4-meter long undulator.

47 OTHER INSTRUMENTATION↗

Size effect in stainless steel thin wires under tension

Miniaturization of modern devices drives the exploration into how materials behave in small dimensions. However, the mechanical behaviors of micro-scale specimens under varied loading conditions are still challenging to characterize and predict. In this work, specimen size-dependent weakening effect was experimentally revealed in 316L stainless steel thin wires under tension with wire diameter decreasing from 200 μm down to 61 μm. The underlying mechanisms were primarily associated with surface grain softening and strain localization, which were largely dependent on the number of grains across wire diameter. Through an analog composite model with surface and interior grains that follows the Hall-Petch relation, the extent of surface grain softening was found to coincide with the flow stress reduction due to lack of boundary strengthening. Further using elasto-plastic self-consistent polycrystal modeling, the stress-strain behaviors of interior and surface grains were well described in analogy to those of bulk materials with similar-size grains and extremely large grains, respectively. Subsequently, the analog composite model well simulated the specimen size-dependent weakening effect under tension. This article provided more insights into the size effect exploration and proposed a practical model for describing size-dependent mechanical behaviors of small-scale materials to be applied to miniaturized devices.

316L stainless steel↗